Can CCNA configure DSL/PPPoE connection into the router?

Similar Questions

• How can I configure numerical Lock ON when the computer starts?

  I have a new laptop HP G70.  In the User Guide HP G70 on keyboards - C01540939.pdf, paragraph 3 using keyboards & pointing devices, Page 8 there is a note "the function of the keyboard that is active when the computer is turned off is restored when the computer turns on.   This does not work on my computer HP G70.  It always starts up the number Lock OFF.   How can I configure my computer to set the digit Lock ON when the computer starts?  I always use the number keypad and never use page up/down - button on top/bottom/right/lelt arrow.

  Also, how can I configure my computer to set the touch mouse on the computer OFF for the start.  I always use an external mouse.

  Any help would be appreciated.  It is a simple thing, but the present operation HP G70 is most annoying.

  PLEASE DO NOT CONTINUE TO MEET THIS PROBLEM!

  THE HP G70 WAS FAULTY!   EACH HP G70 HAS THIS PROBLEM!

  HP REPLACED MY HP G70 WITH a HPdv7.  THE HPdv7 PERFORMED THE DESCRIBER NERMAU LOCK FUNCTION AS IN THE HP INCTRUCTIONS.

  .
  
  Bob_in_PGI

  I'm surprised that nobody knows how to set the Num Lock at startup before you connect.  Where is the help of HP?

  I now have Windows 7 64 bit.

  There must be someone who knows how to do this.

  Bob in PGI

• Just got a monitor hpx2301, can I plug my xbox 360 into the HDMI?

  Can I plug my Xbox 360 into the HDMI

  on my new monitor, it's a hp x 2301

  Thank you

  As long as you have an HDMI cable to connect your XBOX 360 console to your 2301 x monitor, I don't see why it wouldn't work.

  Frank

• Configuring the network for windows7 and computers portable XP with printer connected to the router

  Computer laptop windows 7 works with the printer lexmark that is connected to the router, but the laptop XP who worked with the printer can't find using the "add a Printer Wizard. Two portable computers connect to the internet O K

  Printers configured in this mode are better develop a fixed TCP/IP address.  Your printer manual should tell you how to do this.  In general, there is a 'Settings' menu on the printer where it can be defined.  The IP address should usually have the first three digits than other devices on the subnet (for home networks it would be something like 192.168.1.x) and the final number should be unique and apart from the DHCP numbers range that your router would normally assign (see the manual of your router).

  HTH,
  JW

• iPad can't connect to the router

  Hello

  I have a WRT320N router with firmware version 1.0.01 build 008.  I just got an iPad and so that it can find my router, I can't access the WiFi when I enter my password.  I can use the router with my laptop so I know the login and the password are correct.

  I saw two directors here suggest the same thing.  And one person said it worked.  The same directions were:

  Try changing some wireless settings on the router.

  Connect the computer to the router with the Ethernet cable. Open the router configuration page.

  Click on the wireless tab and put in manual configuration. Change the channel to 11 wireless. Save the settings.

  Go to the wireless tab and click the settings advanced wireless.

  Change the tag to 75 interval, RTS threshold to 2307 and 2306 fragmentation threshold. Save the settings.

  Try to connect to the wireless network again and see if it works.

  My problems are:

  1. I think that my computer is already connected to the router with the Ethernet cable - I want to say that it is an Ethernet cable attached to my computer and my router - in slot 1 on the router

  2 - the only thing I know how to access is the Linksys EasyLink Advisor.  What and where is the router configuration page?

  Thanks - I wouldn't think that if I can't get my router to work, I just lost money on an iPad only WiFi and will instead get one of these devices to attach to the iPad that allows you to connect to wireless internet - like device "clear."

  Read the user guide. The web interface is at http://192.168.1.1/ unless you changed the address LAN IP of the WRT.

• Cannot install a network - error message: this wizzard can not configure a network connection.

  Vista Business SP2 32 bit OS

  Impossible to set up a network connection using a wizzard.  Message: This wizzard cannot set up a network connection.

  A broadband connection was founded prviously.  There is no display of the network in 'connect to a network window.

  a new folder by name hiddenpbk appeared on the desktop and through which I can connect to the previously established connection.  but can not connect via "connect to a network window.  Neither I am able to set up a new connection using the wizzard.

  Please helpme.

  Hello

  Can you explain what connection to a network means in your case?

  What exactly you want to connect?

  If you have a valid broadband (Internet connection), you are already connected to a network.

  If you want to check your wireless system follows this process.

  If as a result of this process, you find something wrong, tell us what it is.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• I have my printer connected to my router via a usb cable... I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print on my prints through the router?

  I have my printer connected to my router via a usb cable. I also have my (Vista) computer connected to the router by ethernet cable. How can I set the computer to print to my printer via the router?

  Usually, you need to install the printing software / drivers on your PC, configured / installed specially for a printer "remote" (its an option in the installation of the printer software)

• WUMC710 connected to the router, but can not see internet

  My media WUMC710 connector on my router Netgear Nighthawk AC1900 double band on the first try.  Can see the MAC address in the connected devices list when you are connected to the router.  However, the devices connected to the WUMC710 cannot connect to the internet.  Tried TV, Blue-Ray and laptop.  All other devices on the wireless network properly.

  What is the problem?

  Fixed a problem with the update of the firmware of the router.  WUMC710 works great!

• BEFSRU31 - connected to the router, but can not browse the internet.

  Hi, I had this problem in the last three months. I share a Linksys BEFSRU31 with my friend. However, once or twice a week, or even more frequently, the router suddenly ceases to send data to my computer. However, my roommate still receives data. So I'm unable to browse the internet even though I am connected to the router and the router gives me an IP address. The only solution I found to do this is to reset the router, which is annoying, because the router is in my friend's room and I don't like to disturb whenever this happens. The ISP is Optimum Online, and I'm on a cable connection 8 MBit. Can someone help me please this problem? Thank you for your time and your collaboration.

  Message edited by EvilBrownie on 18-01-200708:47 PM

  
  

• notification area: How can I get my internet connection and the life of the battery and its return in the notification area

  How can I get my internet connection and the life of the battery and its return in the notification area

  on the bottom right of my screen?

  I tried the properties and to add notifications but it net let me add them...

  Hello

  1 Please reboot nothing so interfere with this process.

  Click with the right button on Taskbar - Properties - tab Notification area - check box Volume - if it is grayed out
  Then, use this link. (The battery is the same method.)

  How to enable or disable the system tray in Vista icons (there are several methods
  and you can to use them all).
  http://www.Vistax64.com/tutorials/106787-notification-area-system-icons.html

  If necessary: a Mr Fixit

  System icons do not appear in the notification area in Windows Vista or in Windows 7 until you
  Restart the computer
  http://support.Microsoft.com/default.aspx/KB/945011

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• My photosmart c309g-m is connected to the router by ethernet cable. Can I add?

  My photosmart c309g-m is connected to the router by ethernet cable.  Can I still add to e-print?

  Hello

  Is a printer ready ePrint? You can use the home router to access the internet? If Yes and Yes, then you should be able to do.

  Kind regards.

• HOW CAN I CONFIGURE BOARDERS TO ZERO AS THE SLIDERS ONLY GO TO 0.13 INCHES

  HOW CAN I CONFIGURE BOARDERS TO ZERO AS THE SLIDERS ONLY GO TO 0.13 INCHES

  Make sure that the sizes correspond to the title of the layout and printing. If you select a pre-set for example the first models LR (1) 4 x 6 you will get margins. On the page layout tab to move all the sliders to zero margin and the size of the cell must then match the custom size.

• WRT54G v4 works PC connected to the router... but not of wireless signal

  The subject says it all.  A few things before this.  One is that we did pass the router in another room.  But things has worked well for a few days after that.  Before just what is happening, I used my phone inter-tel (plugged into the router).  PC and phone continue to have access to the internet... as I say, wireless in the House.  Fact stop and start all.  All unplugged / plugged in.

  Updated the firmware and it did nothing.  Some would like to help.

  After an update of the firmware, you must reset the default router, and then configure the router again from scratch.  If you have not done this since your last update of the firmware, please do it now and see if it solves your problem.  If you have saved a router configuration file, DO NOT use it.

  To reset the router press and hold the reset button for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

  Settings wireless-

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.

  Click on the Wireless tab

  -Here the wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the channel 11-2 wireless, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

  XP:
  Click Start and goto the control panel and double-click on network connections, right click wireless network connection and click Properties.
  Now, in this window, click on the second tab of wireless network and give a check mark on "use windows to configure my wireless" and then delete all network names present in the preferred networks window. Then click OK...
  Right click on the wireless again network connection and then click View available wireless networks and try to re - connect to your network...
  Now, it will give you the opportunity to put the network/wep key, make sure that you enter the correct network key and confirm...
  It will connect...

  Vista:
  Click Start > Control Panel > Network and Sharing Center > manage wireless networks, here to remove any present network and close the window.
  Click on connect to a network and try to re - connect to your network, he must ask for your key/password network, enter the network and password correct key and click on connect...
  It needs to connect... Once you're connected, you must restart the computer, it needs to connect to the Internet...

• Smart Wi - Fi cannot connect to the router

  I can't access my router remotely. It is said that my router has no internet connectivity, but I can access the Internet fine when I am connected to the router locally. Somewhere that my modem is using the bridge to do this, I met and so I tried to fill it, but I still get the same message. Tried changing from dhcp to pppoe, I read somewhere, but my ISP does not seem to support. The router firmware is updated. Help, please. Never been able to use this feature because I bought the router.

  You'll probably have to do a factory reset and set up again. There could be other things to try, but it's the easiest way. If you have a large number of special configurations, you can save the config before you perform the reset of encephalitis in ticks and once that you have reset it and see if it is accessible, then restore settings.

• Connects to the router, but cannot send or receive data

  I have a WRT54G.  I can find the network and connect to the router, but I can't send or receive data.  I tried to connect directly to the router and I still not able to send or receive data. Both computers on the router has the same problem.  I did a reset the router back to the settings by default and still no luck.  Any thoughts?  Thanks in advance for the help.

  The first thing you can try is when you the Modem and the router is connected to the other, disconnect the power from the router and Modem, wait 30 seconds and then plug in the power to the Modem and once all the lights are solid, then connect the power supply to the Linksys router, now check if you are able to go online. If still no then...

  Who is your ISP. So I think you need to re - configure all settings of your router again.

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link