Can I connect SFP GLC-LH-SMD connector lc single fiber on Cisco 897VA Module?
Hi all
Please can I connect SFP GLC-LH-SMD connector lc single fiber on Cisco 897VA Module?
Thanks in advance.
If you have only a single glass fiber then the GLC-LH-SMD = is NOT good
because it is for double connection to a pair of fiber.
You would like more information by your ISP, you will most likely need a GLC-BX-D (RX-TX/1310 nm, 1490 nm) or a GLC-BX-U(1310-nm TX/1490-nm RX)
See below
1000Base-BX10-D and 1000BASE-BX10-U SFP for bidirectional single fiber Applications
SFP 1000BASE-BX-D and 1000BASE-BX-U, compatible with the IEEE 802.3Ah standard 1000BASE-BX10-D and 1000BASE-BX10-U, carried on in a single strand of SMF standard.
A 1000BASE-BX10-D device is always connected to a device of 1000BASE-BX10-U with one strand of SMF standard with functioning of the chain of transmission, up to 10 km.
The communication on a single strand of fiber is achieved by separating the wavelength of transmission of both devices, as shown in Figure 2: 1000BASE-BX10-D transmits a channel 1490 nm and receives a signal of 1310 nm, while 1000BASE-BX10-U transmits at 1310 nm wavelength and a signal of 1490 nm. As shown, the presence of a separator of multiplexing (WDM) length of wave-division integrated with SFP to split the 1310 nm, 1490 nm light railways.
GLC-BX-D and SFP GLC-BX-U supports also digital Optics (DOM) of the functions of surveillance in accordance with approval of the standard of the industry (MSA) multisource SFF-8472. This feature gives the end user the ability to analyze parameters in real time of the FPS, such as the optical output power, optical input power, temperature, laser bias current and transceiver supply voltage.
Tags: Cisco Support
Similar Questions
-
Can I have load balancing for two ISP (PPPoE and PPPoA) on Cisco 897va connections
Hello
I have two ISP connection and I have Cisco router 897va, I want to have the load balancing for two ISP connection second connection is PPPoE connection and second is PPPOA (ATM) connection.
It is possible to do?
Thank you in advance.
You can balance by TCP (the default behavior with CEF enabled) stream. Alias a user turns off a pipe and the next user goes off the next pipe.
Make sure that you use the nat with route map that matchers the output interface, then you just need two routes of equal cost default (a leaver each circuit).
-
Can I connect SINGLE MODE SFP (GLC-LH-SM =) to cord fiber MULTIMODE which has ST connector on the other side (patch panel). What is the loss of this set?
The short answer is Yes.
The contours of the links up to 550mtrs on multimode fiber SFP datasheet . You will need to use a Mode conditioning Patch Cord (CMCP) If your installed MMF is OM1 or OM2 rated, kernel 62.5 microns or 50 microns (use MMF cable connection if your fiber installed is OM3/OM4. You can buy MCPCs with hybrid connectors; LC at one end and ST on the other; available at many reputable suppliers. My link to a hybrid CMCP is 62.5 microns MMF.
I hope this helps.
-
Can I connect 1080 p TV 48 "to my iMac in early 2009
If I use a mini port screen hdmi adapter, can I connect a TV external 48 "1080 p on my iMac in early 2009.
EveryMac.com seems to say there is a limit of 30 ", but they throw in some dimensions of the screen of
2600 x 1600 and I don't know how this fits - I get my TV is 1080 p - 1920 x 1200?
Any clarification would be appreciated.
Take a look-> On Mini DisplayPort to HDMI - Apple Support adapters
You shouldn't have any problem due to the size of your TV, but more probably to the resolution of your TV. However, your iMac supports up to 2560 x 1600 resolution for an external display and your TV got a lower resolution (1920 x 1080), so it should work.
(Please note that your iMac does not support streaming audio via the Mini DisplayPort connector, then you will not get audio on your TV).
-
I have an ipad4. Can I connect it to a boom box type device to listen to music on the speakers of the box. using an RCA type plug/plug?
The iPad lacks a RCA type connector. You can connect from your headphones to an auxiliary, if it works with the headphone jack.
-
How can I connect an iPad Pro to an Apple cinema display monitor?
How can I connect an iPad Pro to an Apple cinema display monitor?
http://www.Apple.com/shop/product/MD826AM/A/lightning-Digital-AV-adapter?FNODE=9 1
or
http://www.Apple.com/shop/product/MD825AM/A/lightning-to-VGA-adapter?FNODE=91
and if the display does not have such a connector you need a converter to make the screen connector
-
DeskJet 2542. Help, please! How can I connect to the ipad
I just bought the deskjet printer 2542 for my son as I said it would work with his iPad. I don't have a computer/laptop and the software is not compatible to download on the iPad. How to connect the printer to the connector wireless without it? Still, can it be done? Really hard!
Hello Ro1312,
Welcome to the Forums of HP Support!
You are able to connect the Deskjet 2540 to the network with only an iPad, I'll link the steps below.
Let me know if it helps.
-
How can I connect 2 monitors for a Pavilion p6 2120 Windows 7
How can I connect 2 monitors for a Pavilion p6 2120 Windows 7
Hello
Based on the following link, you can have 2 monitors, 1 uses the VGA connection and 1 uses the connection DVD
http://www.shopping.HP.com/shopping/PDF/h2m53aa.PDF
All you need is to buy 2 monitors (can also have good analog & digital connectors) and 2 cables. Normally the cables should come in boxes.
Kind regards.
-
Can not connect to the WiFi on MacMini 2014
When I try to connect to any WiFi on my MacMini it says ' Unable to join, try to get closer the router. but the router is right next to my Macmini.
In addition, my wifi connection is correct. It is easily connected to my iPad and iPhone.
I tried transferring a file using release from my iPad to MacMini. It worked.
When I tried to connect to the MacMini with ethernet cable, it worked too!
The only problem is that I can't connect to the router using the wifi on my MacMini.
What should I do?
Try to create a new network location:
Using network locations (Mac OS X 10.6 and later)-Apple Support
Try to connect as a different user.
Have you removed the Mini?
AirDrop uses bluetooth
http://iPad.about.com/od/iPad_Guide/SS/what-is-AirDrop-how-does-it-work.htm
-
Can I connect more than one headset bluetooth with Apple TV 4?
Can I connect more than one headset bluetooth with Apple TV 4?
No, sorry. This is a limitation for all devices Bluetooth headset.
-
Can I connect to Netflix or Amazon Prime with an Apple TV?
Can I connect to Netflix or Amazon Prime with an Apple TV?
Yes, Netflix, Amazon Prime I don't know.
-
Safari can't connect to google
I can not connect to Google, using Safari. I am trying to export my hotmail contacts to a new gmail account.
-
So I recently had my password wrong too many times and my iPhone 4S locked out telling me "iPhone is disabled; Connect to iTunes'. And so I connected to iTunes and decided to restore my phone. I finished the process of restoration of the configuration of my phone, but ultimately, it was not even let me in the phone! Once AGAIN he said "iPhone is disabled; " Connect " to iTunes '. However, this time, this message appeared just when I turned on my phone with a black background. I didn't scan the screen for the error message is displayed (and there was no time to be shown). When I tried to connect to iTunes again as he asked, now it says "iTunes can not connect to the iPhone because it is locked with a password".
So now, he said "iPhone is disabled; ' Connect to iTunes' on my iPhone 4S and ''iTunes can't connect to the iPhone because it is locked with a password ' on my computer. WHAT should I do?
As described in step 2 of "Erase your device with iTunes" in this article, you will need to use the Recovery Mode.
Recovery mode is described in this article as well. You may try to go into recovery mode more than once to succeed.
-
If 2 Airport extreme can stay connected to each other using their LAN ports?
Hello friends,
I would like to know if 2 Airport extreme or 1 Airport Extreme and Airport Express can stay connected to each other using LAN ports at the ends? I thought this is the LAN port 1 connected to the WAN port on the 2nd.
Thank you
To clarify the issue and the scenario, one of my friend described a typical scenario in which there are 2 AEs. AE1 has an ISP in its port WAN and AE2 has a different ISP in its WAN port. This 2 AE can mutually connected between them by using ports LAN AE1 and AE2 ethernet cable? He said this could be feasible if AE2 remained in bridged mode, without using the ISP attached to its WAN port. I just don't get how this is possible. Friends of the search help.
Thank you
-
I can't connect to iTunes Store since I updated ios 10
I can't connect to iTunes Store since I updated ios 10
Even and I am able to connect via the web with the same id / password.
Maybe you are looking for
-
I try to use google search and 'access' denied. Help!
It is a bad day. I am trying to use your search function and everything I plug in there, I get "" access denied message. That's happened? This is my 'go - to' Internet search mechanism, and I have a lot of work on my desk today. Help! Thank you.
-
How can I save Windows XP show size and position?
How to save window size and position?
-
Photosmart C7250 all-in-one: compatibility Windows 10 for HP Photosmart C7250 all-in-one
Hello. I have a HP Photosmart C7250 all-in-one, which I am currently using with Windows 8.1 I think upgrade to Windows 10. This printer is not compatible with Windows 10? If so, do we need to download a new driver? Which one? Thanks for your help
-
No way to do an update or uninstall Silverlight?
I can't uninstall Silverlight? or install a new version? -Patch installed not? -I can't do all the updates! Please help me
-
Download files for use in Illustrator CS5 Adobe Capture CC
I want to download three SVG files I created in CC Capture on my iPad for use on my Mac desktop where I would edit in Illustrator CS5 (upgrade to CC is not an option for me right now). I see the asset via my Adobe account, but I can't access it.Is t