Can I connect to the internet via the simulated device

Similar Questions

• SDK can not connect to the Simulator in VMware

  My operating system: Windows 7 64-bit

  SDK version: 10.0.9; Build id: v201212072306

  VMware Player Version: 5.0.1 build-894247

  Video card: NVIDIA GTX 560 Ti

  I'm trying to use the simulator of 10 BlackBerry, running in VMware Player, to test applications under development in the native BlackBerry SDK. However, when I try to run these applications from the SDK and connect to the Simulator, I see that even though (I think) I got the correctly configured IP address for the target, it is still listed as "Not connected" in the list of Options of the target (I don't know if this is normal or not). Then, if I try to launch the project in any case, I get the following error message:

  "Unable to connect. Make sure USB cable or Wi - Fi is connected, the IP address is correct, and the mode of development. »

  Sorry if I didn't explain very clearly, this is very new to me, and I still have trouble getting my head around it. I'm sure there is probably some information that I forgot to include in this post, but I will provide if I think that whatever it is.

  I have been looking for solutions to the question, but it seems that there could be many possible causes, so I thought it would be better to make a new thread specifically for my situation. I tried the following:

  -Check that the development Mode has been activated (it seems that it has been enabled by default)

  -Ping I thought several times, was the IP address of the command line simulator (sometimes I had to meet with success, but not at the beginning)
  -Disabling Windows Firewall
  -Running a .bat file with 'ipconfig/release; ipconfig / renew. ipconfig/flushdns ".
  -I check the correct target for the Simulator IP address (double-check this confuses me a little, but I think I can find it in "Settings"-> "About" simulation-> 'Network' menu?)
  -Temporarily disable Avast! antivirus software to check if she is interfering
  -Verification of VMware Windows were running (I think he installed four of them in total)
  -Uninstall (then reboot) and reinstall the SDK, Simulator and VMware and restarting, repeatedly

  -Windows asked to troubleshoot the connection of VMnet8 of VMware; He said DHCP must be enabled, but then failed to do this for me (this left me confused; I wasn't sure if it was important or not)

  -Passage of the NAT VMware Bridged mode for the simulator mode, then the connectivity test (it doesn't seem to help, and the "About"-> page 'Network' in the simulation was empty), then power back up

  Any help or any what pointers to additional information, I would give, would be greatly appreciated. Thank you!

  EDIT: I also cant seem to get QML previews to work at all. I don't know if it is related to my other question, but I thought it might be worth mentioning, and this is something else I would try to fix, if possible. I tried to update my drivers, but to no avail.

  Solution found! I just tried to add a target in the software development kit using the IP address on 'Settings' of the Simulator-> "About"-> "Network" screen, but the target has been filtered out of the list, unless I unchecked "target filter based on the selection of C/C++ applications". If I unchecked, the target has been classified as ' 192.168.31.128 (Neutrino / x 86) ', but the Run button was grayed out when I chose it and I noticed the error message, ' binary Selected target do not match x 86 "at the top of the window." I have googled this error message and found the following (quite old) thread:

  http://supportforums.BlackBerry.com/T5/native-development/QNX-IDE-target-selected-binary-and-target-...

  After reading through and testing, it turns out that all I had to do was change the active configuration in the drop-down list at the top of the window SDK 'Device-Debug' for 'Simulator-Debug", little"hammer"that I needed to build to the Simulator and not a real physical BlackBerry device. Here is a quote from the post of cdamus, which is where I found the solution:

  "A little trick to streamline your workflow: prospects for development C/C++ has a little"hammer"toolbar of action that you can pull down (click on the black triangle next to it) to define and build the active configuration in one step, for one or several projects."  The icon to the right (it looks a bit like a sundial) defines the active configuration, but is not build. »

  I took a screenshot to help indicate the setting that I need to use:

  

  Hope this helps you chuma and anyone else who has this problem. Thanks for the tip, cdamus!

• Why can't connect me to Internet Via Ethernet?

  Hello

  I help set up the iMac to a friend. No problem problem connecting to Internet through WiFi but can not get the connection via Ethernet. Cables checked and ethernet and all are in working condition. Took some screen shots but I'm not good at all with this stuff. Can someone explain where I'm wrong. Of course, it's simple for a person - but not for me!

  That's what I mean when I open the network tab:

  

  I'm not with the Mac today so instructions to take with me would be very appreciated.

  Kind regards.

  Are plug you the ethernet cable directly to one of the ports on the router to the ethernet port of the iMac, rather than through network extensions? If so, and it is not working, you have another ethernet cable, you can try?

  If the cable connections are good and it still does not, you can try a reset SMC and NVRAM (PRAM) and then test again:

  Reset the management system (SCM) controller on your Mac - Apple Support

  How to reset the NVRAM on your Mac - Apple Support

• I can't connect to the Preview device.

  It just says: "you do not have access to this service. Contact your system administrator. »

  I am the administrator of the system. I'm on the same network, but there is no link or the QR code is generated.

  I use a mini iPad and the latest Dreamweaver.

  One more thing, you can check, it is how the synchronization parameters behave?

  If it failed, can try you sign of Dreamweaver and leave and sign in to creative cloud and provide contact information there.

  Now start Dreamweaver and then connect you if requested. check the settings for synchronization and device Preview.

  He has worked several times. Hope this works for you also.

  -Lalita

• Connection to the Simulator takes ten attempts to work

  Hey. I can always connect to the Simulator Momentics 2.1.1 (10.3.1.2267) but it always made a dozen attempts of connection. It says to check the IP address, which is correct, and fix the device and make sure the dev mode is activated. Unless someone else has had this problem and resolved, which brings me to something:

  Is it possible to make changes to an application and test the new version without closing and reopening the Simulator?

  See you soon

  J.

  You don't need to close and reopen the Simulator.  Simply press the button on the green arrow again and a version update of your application is built, deployed and launches.

  As to the connection attempts, you're waiting until the Simulator began before trying to connect from Momentics?  Do you have any firewall or VPN software that would block the connection?

• I can't connect to the internet via my host after uninstalled antivirus software and restart

  I can't connect to the internet via my host after uninstalled antivirus software and restart it.

  I use windows xp on my host computer and all computers in my client. After that I uninstalled the free trial NIS version and restart my host, I lost the internet connection. Tried to restore with the restoration of the system, but when I restarted it, it said the system restore could not be made. I changed it then with my laptop and I can connect to the internet as the host.

  Hello

  This can happen if the uninstall process fails and leaves behind a Symantec registry value. See the following Symantec article.

  Unable to connect to the Internet after uninstalling Norton AntiVirus.

  http://Service1.Symantec.com/support/NAV.nsf/8d071816eedd7cac88256c0e005a96e5/751c3298ab99cf7188256d34006702e2?OpenDocument

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows?

  322756 (http://support.microsoft.com/kb/322756/ )

• I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.

  I can't connect to the Internet via the wireless network. It shows that I have local access only. I can't connect even in SafeMode with network.  I have Ping www.microsoft.com and the answer is "ping request could not find host www.microsoft.com.  I am connected to the network wireless through my iPad and can connect via my smartphone. This leads me to believe there is only something configured properly on my laptop. Can anyone provide assistance?

  Hello

  You can try a system restore...

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  .. .choose time, until this problem (you may tick to show more older restore points).

  Tricky

• Can not connect to the internet via my router

  I recently changed my dsl cable and Internet service provider. Everything worked fine when I had dsl (no problem connecting by router) but now I can only connect to the internet when the cable modem is connected directly to one of my PCs. I tried to reset the router by default and computers can see each other on the lan, but after trying to reconfigure the router with the modem cable connected it does not detect not the new address ip & dns info even if the adapter is configured to receive the ip address and dns automatically (in windows and the settings of the router.)

  Is there something else in my network installation of Windows 7 that needs to reconfigure?

  Hi Viking_Dan,

  It is really difficult to troubleshoot network connections because there are so many factors that might cause a problem. I'll do my best, however.

  Make sure that you connected the modem cable to the router using the Ethernet port on the router (Wide Area Network) "WAN". Then try to ping the router from an elevated command prompt window. The default IP address is usually something like 192.168.1.1, or similar. Check with your router's configuration. The ping command is:

  Ping xxx.xxx.xxx.xxx

  (where the x's represent the IP address)

  You will receive all 4 packets back with 0% loss. If you do not have, so I'm puzzled. If you receive all 4 packages without losses and still can't connect to the internet, then check if the radio for the router matches the capacity of your PC. Your router may have a frequency of 2.4 GHz only, only 5 GHz, or a mixture. Your PC can support one of those, or both. Check to see if they match.

  If it still does not work, try to set a static IP address for each of your PCs, with the IP address of the router as the default gateway. For the DNS server, I suggest that you use the DNS from Google free, fast and secure server. The IP address is 8.8.8.8

  Let me know what happens

• I have the wireless option, but if I use it not I can't connect to the internet.

  I have the wireless option, but if I use it not I can't connect to the internet.

  original title: difficulty borrowed from internet

  If it's the Acer utility, it is best to visit Acer support:

  http://support.Acer.com/us/en/default.aspx

• I can't connect to the Internet wirelessly

  I just replaced my wireless device and now I can't connect to the Internet wirelessly

  Hi JimMahoney,

  You have installed the necessary drivers for your new wireless device?

  You receive an error message when you try to connect to the internet using your router?

  What virus protection software is installed on your computer?

  I suggest you try the steps mentioned below.

  Method 1: Run the network troubleshooter utility in Windows 7.

  Please follow the steps below mentioned link to run the network troubleshooter utility

  http://Windows.Microsoft.com/en-us/Windows/help/network-connection-problems-in-Windows?T1=Tab03

  Method 2: You can also check the configuration of your new wireless device.

  Contact your Internet Service Provider (ISP) or wireless device manufacturer to check the configuration of your wireless device.

  I hope this helps.

• I deleted a virus from my computer this morning with Security Essentials, now I can't connect to the internet.

  I deleted a virus from my computer this morning with security essentials, now I can't connect to the internet. The connection icon in the lower right corner of the screen says I am connected and the signal strength is 'very good', but I can't go online. The error message I receive when I right click and 'fix' the connection says: "failed to query TCP/IP connection parameters. Cannot continue. " For assistance, contact the person who manages your network. How can I fix it? The computer is a HP Pavilion dv2000.

  original title: can't get online

  Hello BurnBurn,

  I suggest you to re-installing the driver for your network card. This may involve completely un-installing it and re - install:
  http://support.Microsoft.com/kb/283658

• After the removal of a virus, I can't connect to the internet, is looking for an IP address, and the RPC server is unavailable, said

  My netbook has a virus so I did a scan and remove infected files and a program which the virus attached itself to.  Now, I can not connect to the internet.  He is looking for an IP address, and he also says that the RPC server is unavailable.  Any ideas?  Help

  Hello

  Step 1: Start your computer in safe mode, and then try to start the Remote Procedure Call (RPC) services and start the computer in a clean boot
  a. Click Start, type services.msc and press to enter.
  b. in the list of services, double-click Remote Procedure Call services.
  c. change the startup type to automatic, and then click Start.
  d. click ok to apply the changes.

  Reference: http://windows.microsoft.com/en-US/windows7/what-is-safe-mode

• I have a laptop with Windows XP. After getting a virus, I scanned with AVG and removed the threat. After re-booting, I can not connect to wireless internet.

  I have a laptop with Windows XP.  After getting a virus, I scanned with AVG and removed the threat.  After re-booting, I can not connect to wireless internet.  The icon shows "acquiring network address".  I connected the router directly on laptop computer connected to the wireless network and still unable to connect.  I tried to restore the system as well, but the message says "unable to restore the system, no changes were made.  Help?

  original title: acquisition of network address

  Hello, Steve.

  Try this link below on how to reset IE and let me know if it helps.
  http://support.Microsoft.com/kb/923737

• I can't connect to the internet on this laptop wireless

  Hello. For some reason, I can't connect to the internet on this laptop wireless. I used to access through wireless, but recent I tried several times without success. I even leave do to set still no chance. I am pretty frustrated here, can you help please.

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://support.Microsoft.com/kb/870702

  It will be useful.

• My wireless on my laptop will read the files on my desktop but I can't connect to the internet, my lapto electrician iI unless other computers work well

  My wireless on my laptop will read the files on my desktop but I can't connect to the internet, hard wire my laptop iI unless other computers work fine

  The following diagnostic information:

  1. Connect your laptop wireless so that you can "read the files on your desktop."
  2. Open a command prompt window (start > run > cmd > OK)
  3. Type the following command in the black command prompt window and press enter

     ipconfig/all > "% userprofile%\Desktop\testdata.txt".

  4. Let the window open orders and "hard wire" your laptop to connect to Internet
  5. Type the following commands in the black command prompt window and press ENTER after each one

     ipconfig/all > "% userprofile%\Desktop\testdata.txt".
     Notepad '% userprofile%\Desktop\testdata.txt '.

  6. Copy and paste the contents of the testdata.txt file into your answer here

  Please note that there are 2 for the second command ipconfig > characters.

  You can close and remove testdata.txt (which is located on your desktop) and close the command prompt window.

• I have a WAN Miniport PPPOE problem. Can't connect to the internet.

  I have a WAN Miniport PPPOE problem. Can't connect to the internet.

  Hello

  If you have a Modem and a wireless router or a Modem/Router combination. Read its manual and configure the WAN for PPPOE port.

  http://www.ezlan.NET/PPPoE.html