Can only start a barrette of RAM at a time (2x4gb OWC Upgrade)

Similar Questions

• I can only start my computer in safe mode, what can I do?

  Hello

  I can only start my computer in safe mode and my security settings are turned off, what do I do?

  I tried to download an anti virus scan, but it does not work?

  Hello

  1. what happens when you start your computer in normal mode?

  2. what version of Windows is installed on your computer?

  3 are you aware of any changes made to the computer, before the show?

  Assuming you have Windows Vista or Windows 7 is installed on the computer,

  Method 1:

  Perform a clean boot and check for the issue.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once you are done with the boot, follow step 7 of article to put your computer to normal startup.

  Method 2:

  Check if your computer is configured to start only in safe mode.

  a. Click Start, type msconfig and press ENTER.

  b. click on the Startup tab.

  c. under Start Options, uncheck safe startup.

  d. click on apply and OK.

  I hope this helps.

• Computer hangs, reboot, can only start in safe mode

  Original title:-i can only start in safe mode

  Ive tried to use several restore points but when I try to reboot the computer freezes and I have to start in safe mode

  Safe mode is a mode where Windows works only the bare minimum programs and processes necessary to the performance of your system.  When you start in Normal mode, many more processes and applications running.  At least one of these programs or process causes your computer to crash.  If your task is to identify this program/process and, at least temporarily, to prevent it from running at startup.  Microsoft has a tool that you can use to selectively disable or or the process that normally run at startup called "msconfig".  It can be a long and exhausting iterative process of turning things off and restart to see if it you fixed program, but that's what you do:

  "How to solve configuration errors by using the System Configuration utility in Windows XP"

  <>http://support.Microsoft.com/kb/310560/en-us >

  First, disable all items "start-up".  If it does not, set it to 'Services '.  If this does not work, then reactivate some of them and try again until you zero - in on the culprit.

  HTH,

  JW

• I can only start using the list of Windows XP

  Original title: WINDOWS XP STARTUP W/DISC PROBLEMS

  I have a problem starting my desktop xp computer. I can ONLY start with the XP disk, of course, I have to press 'R' over and over again. After a few tries, it starts well, how can I start up without having to redo this process over and over again. I passed by 'MSCONFIG' and past from NORMAL to SELECTIVE startup and even deleted some programs from my hard drive. I can't make changes without putting in my (domain name Name\Administrator). I don't know what could be and am lost at this point... HELP!!!!!!!!!!!!!!!!

  THOMAS

  Hi Thomas,

  ·         Did you do changes on the computer before the show?

  ·         You receive an error message or error code?

  Follow the suggestions below for a possible solution:

  Method 1: Remove all external devices connected to the computer such as printers scanners or USB external hard drives and restart the computer and check if you receive the error.

  Method 2: Try to start the computer in safe mode with network and check if the issue still persists, see the link below to start in safe mode.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

   

  Method 3: You can try and perform a system restore to a date when things were working well and check.

  How to restore Windows XP to a previous state

  http://support.Microsoft.com/kb/306084

  In addition, you can also download the minidump files so the experts here can analyze the cause of the problem.

  How read partial memory dump files that Windows creates for debugging

  http://support.Microsoft.com/kb/315263

   

  Use SkyDrive download collected files and post screen shot/image

  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  Let us know the results.

• I have windows xp after the installation of service pack 3 I can only start in safe mode

  I have windows XP after the installation of service pack 3 I can only start in safe mode?

  Hello

  ·         You get the error message?

  ·         What happens when you try to start in normal mode?

  Method 1

  Windows XP can in every start Safe Mode by default. Even if you select the option Start Windows normally, it always starts in Mode without failure. IOW, you can't get out of safe mode.

  This happens if the switch/SafeBoot is added to the Boot.ini file. / SafeBoot parameter forces a boot in safe mode by using the specified parameters. The available parameters are:

  (a) minimal (b) network (c) safeboot: minimal (alternateshell) For more information about the boot.ini switches, see visualization and correction of the settings of the boot on x 86 systems RESOLUTION (a) click Start, run and type MSCONFIG (b) click the Boot.ini tab (c) If you have a dual-boot system, select the entry that is appropriate under the [operating systems] (d) in section downstairs, Startup Options uncheck / hisFEBOOT (e) click OK (f) restart Windows The entry/SafeBoot are removed from the Boot.ini file.

  Method 2:

  If the above method is not the cause, it seems that Service Pack 3 is not installed correctly.

  Step 1: You try to run the system restore from safe mode that will repair return the computer to the point while it was working fine.

  How to restore Windows XP to a previous state

  Step 2:

  I suggest you follow the troubleshooting steps form the article and check if it helps.

   

  How to troubleshoot an installation fails on Windows XP Service Pack 3

  http://support.Microsoft.com/kb/950718

  Note: System requirements to install Windows XP SP3

  Reference: Learn how to install Windows XP Service Pack 3 (SP3)

  Hope the helps of information.

• Is it true that I can only transfer my license FPP windows 7 10 times?

  Is it true that I can only transfer my license FPP windows 7 10 times?
  What should I do if I reach the limit?

  Is it true that I can only transfer my license FPP windows 7 10 times?
  What should I do if I reach the limit?

  You can reinstall and transfer your Windows FPP retail as many times as you like - there is no limit.

  However, there is a limit to how many times you can use the online activation. After awhile, you will need to use the phone activation when reinstalling.

  Installation and reinstallation of Windows 7:

  http://Windows.Microsoft.com/en-us/Windows7/installing-and-reinstalling-Windows-7

  Activate Windows 7 on this computer

  http://Windows.Microsoft.com/en-us/Windows7/activate-Windows-7-on-this-computer

  Case of failure of the online activation:

  Call Microsoft use the manual phone Activation

  Note: If you always install Windows page enter your product key, do not enter your key and uncheck the "Automatically activate when online" then click OK/next to complete the installation.

  1. open Windows Activation - click on the Start button, right-click computer, click Properties, then click the option to activate Windows now or change your key.

  2. click on show me other ways to activate.

  3 type your Windows 7 product key, and then click Next.

  4. click on use the automated phone system.

  5. click on the location nearest you from the drop-down list, and then click Next.

  6. dial one of the available phone numbers listed.

  7. do not select all options and wait for a person pick up, then explain what happened.

  Can move you to a new Windows 7 computer

  If it's a full license or upgrade retail - Yes. You can move it to another computer as long as it is installed on a single computer at a time (and if it's a Windows 7 Upgrade version the new computer must have its own qualification license XP/Vista/7). The previous installation of Windows 7 on the old computer must be formatted or deleted. You will have to perhaps call Microsoft and explain what happened to complete activation. Turning it on the second computer will automatically be in effect 'disable' the license for the first computer. The key works with 32 and 64 bit, but can only be installed at a time.

  If it's an OEM license - don't. OEM licenses, including Windows preinstalled on a computer before purchase and Windows purchased separately, are related to the first computer, they are installed on and cannot be transferred to another computer. To install Windows on another computer, you will need to buy another copy.

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• SP3 update: problems, can only start in safe mode

  Windows XP Home Edition: update to SP3, in the hope that it would, among other things, allow me to install the windows update service. Unfortunately, I can only boot in safe mode. If I try the normal startup, it goes into a boot loop. By that I mean that he tries to startup that fails, she tries again, then fails and just keep the loop. All of the answers.
  The only way I see is to uninstall, and which may not be the right answer.

  Hi, Harvey,.

  Try the solution given by DenyB:

  "Installation disk to boot into the Windows XP Recovery console. He asks which disk you want to access and the Admin password (if you do not have a fair shot of password to enter). "Then type: COPY C:\WINDOWS\SERVICEPACKFILES\i386\gdi32.dll (1 place) C:\WINDOWS\SYSTEM32\gdi32.dll press enter crush Y (Yes) press enter type EXIT reboot should Do It."

• Satellite Pro A100-830 - can only use 3 GB of RAM under Windows 7 64-bit

  Hello

  I just upgraded my laptop Windows 7 Ultimate x 64 and also improved my ram to 4GB (2x2GB)

  Windows is to see all 4 GB but says only 3 GB is usable, because it is a 64-bit version of Windows wouldn't be able to use all the 4 GB?

  Any help appreciated

  Thank you

  Laptop specs

  Intel Core2Duo T7200 2.0 GHz
  RAM DDR2 677 MHz 4 GB
  ATI Radeon Mobility X 1600
  120 GB HD

  Hello

  Have you already checked the BIOS? How much RAM show the BIOS?
  And what kind of modules you have exactly?

  Normally, it should be possible to use full 4 GB of RAM on a 64 bit OS as your laptop also supports 4 GB.

  Maybe you should also try updating the chipset driver. You can find it on the Toshiba site.

• Re: Satellite P300 - 19 p - can only start in safe mode

  I started up my laptop recently and there is no noise when Vista starts loading and then Vista crashes while loading. Now I can run only my laptop is safe mode.

  The sound card will not affect Vista, and can do something if the sound card is faulty?

  Hello!

  As Luke has already said if an earlier work of t restore point doesn't use HARD drive recovery.

  If you don't know how to use it, you should read this article:
  http://APS2.toshiba-tro.de/KB0/HTD9102IR0000R01.htm

  Good bye

• start-up after norton install fails can only start in safe mode

  I don't know how this problem started, I got a blue screen on startup, start single icould my pc in safe mode.

  The only way I could use my pc was to do a system restore.

  At this point, I have lost Norton 360 v 3?

  I contacted norton and they have been very helpful, they re-installed norton remotely.

  they are just me to reboot my pc

  My pc is restarted, I got the blue screen and could only restart in safe mode, I had to again, restore the system to get online and I lost norton, but the Startup icons are still there.

  The problem may be caused by the incompatible Norton (Symantec) with the hardware or software you installed recently.

  Uninstall Norton (Symantec) in Mode completely safe
  

  ==========================================

  1. reboot the computer and start pressing the F8 on the keyboard key. On a computer that is configured to start to multiple operating systems, please press the F8 key when you see the boot menu.

  2. when the Windows Advanced Options menu appears, select Safe Mode, and then press ENTER.

  3 log on to Windows by using the administrator account or any user account with administrator privileges.

  To uninstall Norton Internet Security, please run Norton Removal Tool.

  Note: If the following tool cannot be downloaded via Safe Mode, I suggest we first download it on a different computer and then copy it to the problematic original computer to install it.

  4. Please visit the following Web site to download the tool:

  http://Service1.Symantec.com/support/tsgeninfo.nsf/docid/2005033108162039

  5. save the tool for Windows Vista desktop.

  6. run the tool according to the instructions on the Web site.

  7 restart the computer

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error starting XP - can only start in safe mode

  I have XP with Service Pack 3.  When starting, I get the following message:

  ("We apologize for the inconvenience, but Windows did not start successfully" it gives then five options: 1) start windows normally. (2) safe mode; (3) safe mode with networking; (4) safe mode with command prompt; and (5) last known good configuration.

  The only option that works is safe mode.

  Safe mode, I made several attempts to restore the system, without success.

  I ran SuperAntiSpyware and Malwarebytes Antimalware, find no malware.  However, my antivirus program cannot perform a scan.

  I have no connection to the internet.

  Any suggestions would be greatly appreciated!

  Well done.

  The savrt.sys file is a driver belonging to Symantec.  I think it stands for Symantec Anti Virus Run Time (good guesser).

  It could be that you got some update that did not work completely or is not compatible with anything else on your system.  I spend too much time trying to understand it, I uninstall, download going again and then reinstall the latest version.  Maybe your cleaning program clean up too much or not enough.  What happened, you know what at least part of the problem is now you can work on fixing it.

  You can see if you can get help from Symantec, but sometimes they tell you that your only solution is to resinstall XP or let them connect remotely to your system and run their tools and perhaps their 'Eraser '.  I've never seen a happy ending with these approaches, but you could see what they have to say.  They may not know immediately and exactly what to do.

  If you paid for the Service, he came sinstalled or you got by your Internet provider, I would uninstall it making sure to use the Symantec unintaller who is here:

  http://us.Norton.com/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834EN

  The tool is an executable, so you may need to copy to your Internet system not using a USB key... or maybe someone else has other ideas.  I have not used all of the Symantec products in a long time.

  You can click on start, run and enter in the box:

  Msconfig

  Click OK to enter msconfig and see if you can locate all Symantec, NAV stuff in the tabs XP Services and startup and disable the (this does not uninstall anything) and see if you can boot normally and go online to download the tool.  I have just do one thing at a time and restart until you can start normally (sorry for the trial and error).  Make notes of what you turn off when you turn off something that is no better off so you can put it back.  Do not disable the just what you see in msconfig if you don't know what it is or is not obvious (look for the stuff Service or SYM).  I only remember that the savrt would be in the Services tab.

  This also explains why you can boot mode safe too - Symantec stuff will not be loaded in Mode without failure.  Symantec/Norton is part of the affection.

  Perhaps using Add/Remove programs to remove Symantec will work enough for you will get, but the Symantec tool must be run at a time to clean up the damage.  It must be a bit messy, since they had to come out with their own removal program (but a lot of antivirus provider it nowadays).  I do not like the installation of their products to see how it works these days.

  I would like to use msconfig to disable as much as you can find a little at a time, then see if you can boot normally and get on the Internet.

  Of you can just hang out and wait for other ideas for other ways to remove or to start normally.

  What happens when you try to get on the Internet now (not to mention it doesn't)?

  They you will need to decide if you can fix your Symantec or just drop out all together and use something else after this pleasant experience.

  Some people really like their Symantec/Norton products, so I'll try not not too bad the bash.

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• I can only start my computer in Safe Mode - system hangs on startup after installation of updates

  Original title: UPDATES DOWNLOADED PROBLEMS to START NORMAL, MUST LOAD IN SAFE MODE - LOST AFTER 30-40 SECONDS VIDEO

  After the download and installation of updates on my desktop Gateway (FX7020) the computer freezes on me and was forced to shut down hard. After a few attempts to start the computer, I was able to get into safe mode. After some time in the exploration of the event viewer I tried out and re-start of normal BONE. I was unable to make it through the boot sequence and had to shut down hard again. I waited a while and it made back in safe mode, but this time after 25-40 sec. I lost the video, the mouse, the keyboard. Everything was running. I've read a few articles and I hope that I don't have a F... THE OS.

  Thanks any help will be graciously appreciated... RA

  Hello

   
  Method 1:
  You can try restoring the system to safe mode and check:
  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
  You can consult the links for:
  System restore
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions
  
  Method 2:
  If the problem persists, you can refer startup Repair in Windows Vista, which is a recovery tool that can fix certain problems. You can check the link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

• Since my computer downloaded the auto update: hotfix for windows XP (KB2570791), it does not start in place... the screen goes all black. I can only start in safe mode.

  I restored the computer to a previous point, but as soon as I stop and restart, the same thing happens. ??

  Hello

  You can try the steps listed in the link: after the Windows Logo appears, or after you log on Windows, a Windows XP computer can display the wallpaper, a black screen or a blue screen: http://support.microsoft.com/kb/318027

• When I click on a tab, the tab will not open, so I can only have one tab open at the same time. How can I fix it?

  I use Firefox for about a year, and I use several tabs all the time. Tonight, when I clicked to open a new tab, nothing happened. Firefox starts and displays the first tab with the site, I've specified, but when I try to open new tabs, nothing happens.

  You probably have an another addon that is the cause.

  http://support.Mozilla.com/en-us/KB/troubleshooting+extensions+and+themes

• HP Envy H8-1549: computer doesn't recognize only half of the new Ram

  Hi all.

  I took a set of ram Ripjaws X 32 gig (4 x 8).  When I install all four chips, only half of them are recognized by the Bios. If I remove two, both of which have not been recognized are visible and working in the same locations they were. It all works, but not all.

  Current configuration: http://support.hp.com/us-en/document/c03666767

  RAM: http://www.newegg.com/Product/Product.aspx?Item=N82E16820231569

  Everything I read on my motherboard and ram has indicated that it is compatible. I updated the Bios and erased the CMS.  I'm a bit of a loss. Am I missing something fundamental?

  What is a tension problem? If so, how can I send it?

  RAM is usually such an easy upgrade. Not so much this time, it seems to me.

  Thank you.

  This seller has guaranteed 8 GB modules for the H8-1549 envy.  The specs are "CL11.