Can't access BIOS - Portege R500 PPR50E

Similar Questions

• Portege R500 (PPR50E) speaker does not mute when headphones plugged

  Hello

  I am using Toshiba Portege R500 (PPR50E) with Windows XP Professional (SP3).

  The problem is the 'secret' doesnot portable speaker when I connect the headphones. The audio is coming from headphones and speakers of the laptop. It is verymuch irritating when you do voice chat. Is there a solution for this problem?

  Thanks in advance,
  Dev

  Hello

  I guess you have a Realtek audio chip.
  In Control Panel, you should find the Realtek HD audio Manager.

  The Audio i/o tab contains settings.
  I put t remember exactly how they call but you will see the audio jacks.
  Here, you will need to right click and change the setting.

• How can I access BIOS?

  Title: original passport / BIOS

  Does not start with Passport attached to the USB port...  Said to eliminate "USB boot" from the BIOS.  How can I access BIOS?  The support fellow WD told me to push "F10" at the start, but it just sent me multiple choice starter.

  Depends on the brand and model of your system. When the initial screen, you should see similar instructions to "Press F1 to enter setup". F1 is just one example. It might be F2 or DEL or any other key. You disable and then boot from a usb device. The problem should be solved.

• Portege R500 - PPR50E replacement of the HDD or SSD

  Hello

  The hard drive in my beloved Portege R500 is dead.

  The model is a Toshiba MK1237GSX and am looking for a compatible hard drive to replace it with conclusion that this exact model turns out to be difficult. You can also and my first choice would be to replace the HDD with a ssd drive - is this possible and any recommendation on model?

  Any help is very appreciated

  Thanks in advance

  Agree with Akuma.
  You need an SSD that supports the SATA interface.
  You need disc SSD SATA 2.5

• Can I use my Portege R500-121 3 G for GSM calls

  Hello

  I have TOSHIBA Portege R500-121 3 G.

  Can I use my TOSHIBA for GSM calls and if SO what software do I need?

  Thank you

  Hello

  No, you can t make GSM calls.
  You can only use it for a data transfer.

  If you want to make a call, you need an internet connection and could use a software like Skype for example.

• Re: Satellite A500-1GL - Can t Access BIOS aftre updated

  Hello
  I have a laptop A500-1GL.
  Yesterday, I checked that the drivers download page, just to check if there is something new. and I noticed that there was a new version of the BIOS.

  My old BIOS:
  SystemBiosVersion: 1.6
  SystemBiosDate: 05/06/10

  the Web site was:
  Version: 1.7
  Date: 29/07/10

  So, I downloaded this file and flashed the BIOS... after the reboot, I checked the "regedit". and the version was changed to 1.7, but the date remains the same (05/06/10)!

  Now, this isn't a big problem - I know, but I wanted to check the BIOS configuration (before the start).
  So I restarted the laptop, you press "DEL"... nothing happened, went straight to Windows!
  I tried again, with F1, F2 ~ F12... anyway.
  So, how can I access the BIOS Setup screen? I tried re-flashing the BIOS again, but he keep saying that I already have the new version, so I can't flash.

  any ideas?

  Hello

  > So, I restarted the laptop, you press "DEL"... nothing happened, went straight to Windows!
  > I tried again, with F1, F2 ~ F12... anyway.

  It looks at, start fast, active in the Bios. Read this thread, the Andrusito guy explained how he has disabled it:

  http://forums.computers.Toshiba-Europe.com/forums/message.jspa?MessageID=208999#208999

• Can't access bios dv3500

  I've updated my OS to Win 8.1 and while the operating system works very well - I can't access the BIOS during startup.  I made several tough stops and restarts and tried (F1, F2, F8, F12, DEL, and ESC) but I am unable to enter the bios.  Y at - it a workaround solution that will allow me to interrupt the boot to access the BIOS?

  Hello

  Now try the SHIFT key when you click Shutdown to temporarily prevent a hybrid boot.  Then away to the ESC key as soon as you press the power button and see if it launches the Start Menu - if this is the case, select the Bios Menu (f10) from here.

  Kind regards

  DP - K

• Fingerprint sensor can be found on Portege R500

  Since my Portege R500 has recently developed a habit of not being able to find the fingerprint sensor.
  I have re-installed Truesuite (new version 2.0.2.0) but that didn't improve matters.

  On startup, I get an error software fingerprinting system is not available.
  At the start of TrueSuite, trying to footprints fingerprinting registration, I get a message "cannot open the sensor.

  Am I missing a driver or so (at the start there is also a cryptic message on a port USB)

  Any ideas?

  It of difficult to say why the new fingerprint driver or software does not solve your problem

  The whole story is really mysterious.
  The European driver Toshiba page provides the AuthenTec fingerprint software (v2.0.2.0)
  If reinstalling this software does not help the question must relate to a corrupt Windows Vista files and in my opinion that using the Toshiba Recovery CD should help.

  A question:
  Have you installed SP1?

• Portege R500 ppr50e - boot from SD card

  Hi all

  I thought to buy a 32 GB SD card for my ppr50e r500-05402ren, so I can install Ubuntu and have a system dual boot with Windows 7.

  Does anyone know if it will work?

  See you soon,.
  Al

  Hello

  As far as I know the BIOS of the R500 is able to boot from the HARD drive, Network (LAN), FDD, USB, SD, USB, ODD USB memory.

  So if you would create a bootable Ubuntu SD then you should be able to boot from the SD card.

  Welcome them

• Satellite A110-179 - BIOS password has been changed - can't access BIOS

  Hi, everyone:

  I have a problem with my toshiba satellite A110-179.
  I'm not exactly how, my computer has set a user password CMOS, which completely avoid me access to the BIOS, or a correct boot system settings.
  So I Don t know to restart the CMOS settings, to remove all configurations, the user password that is included in this.

  I been reading about the process of possible resetting my BIOS of the laptop, so I can't find exactly how do, so everyone know that it is impossible in laptops from Toshiba, reset the default installation settings.

  Is this true?
  Can I do something?

  Please, explain the process. I'm completely hopeless on this issue.
  Excuse my terrible English, it has been forgotten.

  Thank you, for your help.

  Best regards from the Spain.

  Hello

  Is the password of the BIOS cannot be deleted by the user if the user doesn t know this password.
  In this case, the ASP from Toshiba (certified partner) must be contacted in order to remove this password.

  Sorry mate but to my knowledge, there is no other way to remove it
  Therefore, get in touch with your ASP and ask for help!

  Good luck

• be hpe530: can't access bios

  After updating the firmware to 7.15 the system restarts fine
  The second time was select the boot device to obtain hollow the boot process
  The third time I changed the boot order in the bios and from that moment, I was unable to do something
  I disconnected the sata drives and battery to reset thr bios but success witjout
  I am unable to access the bios pf10 stille
  What can I do else?
  Windows 7 64 standaard hp installation environment (with a bootmgr I guess.. original hp installation)

  Thx for your answer, but I was not able to access the Bios with the F10 key

  I solved the problem by unplugging the battery and the 220V taken during 2 min...

  From that moment, I could access the bios.

  But my first problem was solved not (bootmgr missing)

  Months ago, I copied my system on a ssd and it worked without changing anything on the partition definitions

  After installing the new firmware, I received the message "bootmgr." missing

  I started a "partition mgr" by starting from the cd and noticed that my old drive without system has been defined as active

  The ssd with the system on it was not "active".

  I changed the 'active' and on the next reboot, a HP utility (?) noticed a problem and automatically repaired

  == > All problems solved

  I installed a new firmware because I thought that the time between the market and the login screen was taking too long for one SSD boot (40 seconds)

  Once you log in to windows it happens very fast

  Is there a solution to reduce this time-out before the login screen, or is this normal

  Thanks in advance

• Can't access bios on Y580 Windows 8

  After the upgrade to windows 8, I can no longer access the bios. The lenovo screen appears at startup, but no startup option. And just to make sure, as someone who still has windows 7 please tell me which key allows you to participate? I tried everything, but I'm stumped.

  Hey Tyler,

  Please see article "how to get into BIOS...

  http://forums.Lenovo.com/T5/Windows-8-knowledge-base/how-to-get-into-BIOS-after-win-8-upgrade-or-on-...

  Zehn

• Pavilion p7-1254: can't access Bios - Windows 7 pro

  I tried the methods "F10" and "esc" while restarting, but whenever I do, I get in a configuration screen of HP with no way to get to the bios.  I just installed a hp amd radeon graphics, that works very well. However graphics originally included is automatically disabled. In order to use my sound bar speakers, I need to get into the bios, so I can enable the audio part of the map. Thanks for any help.

  You repeatedly type the F10 key at startup to access the BIOS

  This will help you with the setup of the BIOS:

  http://support.HP.com/us-en/document/bph07110

• HP laptop - 15-r224tx: can't access BIOS without password

  I try to access my BIOS but do not have the administrator password.

  When trying to jump by pressing on enter it fails and I get a message "system disabled [12345678]."

  The most recent value included in the disabled system message is 68026369.

  Can you please provide the password so I can access my BIOS?

  Hello

  Use the code to reset below

  77984969

  If the above does not work, follow the steps below to link to generate the reset key

  http://h30434.www3.HP.com/T5/notebook-operating-systems-and-software/system-halt-error-message-or-BIOS-password-reset-generator/TD-p/5010033

• H8 - 1420t envy: Hp Envy - can't Access BIOS Can or Start Menu after replacing HARD drive

  Hello!
  
  One of my friends has problems with their computer and gave it to the difficulty. First thing I did was try to start it up and it didn't not even start. He tried the auto repair and failed. Then attempted to fix startup problems via the Win8 splash screen and doesn't have too much that. So, I tried a refresh and even that failed. I took out the hard drive, connected on my PC at home and save all the data I could find. I had problems with some data and often he would crash my windows explore (as my friend told me that he did while they were using the PC), so I've determined the drive HARD shot.
  
  Got a new HARD drive and put it in. At caught my drive of Windows 8 and slapped in. When I went to start the PC, I tried to hit all the keys BIOS I could think: Esc, f2, f8, f10 and f12, del even. Nothing has worked. He's just sitting at the HP logo and then after about 20 seconds, he went to a black screen that says something along the lines of "not detected no boot disk".
  
  I can't boot into the BIOS. If I plug the old drive hard when I get to the blue screen of Windows 8 start with parameters such as the "Refresh" and "reset the PC. If I try to access the CD/DVD drive under the 'Remote access' button, I get a black screen with a cursor. It just freezes there. If I try to access the settings of UEFI, it freezes in the blue menu with functions.
  
  I don't really know what to do here. I'd appreciate any help! Never had a problem this stubborn before.

  Wanted to just go back and say I have solved my problem.

  The computer didn't like the keyboard I used! I caught a pretty generic keyboard that was laying around and plugged him that. Hit Esc at startup led me to the boot menu.