Can't forget the network

Similar Questions

• How can I get the "network" icon in the taskbar? The box of 'network' in the bar of tasks and Start Menu Properties; Notification area; System icons, will not respond to what it is.

  How can I get the "network" icon in the taskbar? The box of 'network' in the bar of tasks and Start Menu Properties; Notification area; System icons, will not respond to what it is.

  Use this tutorial:

  http://www.Vistax64.com/tutorials/106787-notification-area-system-icons.html

  Go to method 3.

  3. for the network icon.

  (B) to activate the icon network - Enable_Network.reg< click="" to="">

  * Don't forget to restart to complete the procedure. ***

• I am not able to connect to the main wifi network but can connect to the network of comments.

  Hello

  This is something new, I am facing to where I am not able to connect to a main network of airport extreme, but can connect to the network of comments. Guest network works perfectly fine while the main network does not connect to devices in the home. I also found that none of my base stations are visible in the airport utility (I Airpot extreme and Airport Express on the same network). Help, please.

  The first step in troubleshooting with this type of problem is to perform a complete network power cycle on your network. If you decide to do...

  Power off all the devices on your network... modem, routers, computers, printers, etc... in any order you want.

  Wait a minute

  Turn on the modem first and leave a few minutes, he managed by itself

  Turn on the next device that is connected to a modem and leaves turn a good minute

  Keep turn on devices one by one at a time, one minute apart, until the entire network is back

  Recheck the network and report on your results

• I use iphone 5 s updated to 9.2, but I can not use the network and call :( Please help me

  I use iphone 5 s updated to 9.2, but I can't use the network and call someone help me please

  What happens when you try to use the network?

• Using Windows XP with an access switched. How can I stop the network Dialer to invite the user connect even if I checked never dial a connection in Control Panel, then apply, then OK?

  Using Windows XP with an access switched. How can I prevent the network Dialer to invite the user connect even if I checked: never establish a connection to the Control Panel, then apply, then OK? She comes right back in a few minutes for: always connect by default. Help! Control panel Connections tab doesn't really seem to apply my change to never establish a connection right back to always make the default connection. What else is there to do?

  Hi Richard,

  You did it all change hardware or software on your computer before this problem?

  You can follow this link & check if the problem persists:

  Network connections and remote access troubleshooting

  Hope the helps of information.

• can connect to the network but not internet XP

  I use a computer on a local network xp, can connect to the network, ping the DNS server, gateway, etc.  However, I can't not conncet to internet.  When I ping a web address using the address of the site name or xxx.xxx.x.xx I have no success.  Tried to reset winsock, tcp/ip, without success.  Would appreciate any help.

  First course of action:

  1. turn off the PC.

  2. turn off the router.

  3. turn on the router.

  4. turn on the PC.

• I can´t find the network controller driver. Is Hp 2000 - 2d09EE, 8 x 64 windows. Please can you help me?

  Hello

  I can´t find the network controller driver. Is Hp 2000 - 2d09EE, 8 x 64 windows. Please can you help me?

  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C & REV_01
  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C
  PCI\VEN_168C & DEV_0036 & CC_028000
  PCI\VEN_168C & DEV_0036 & CC_0280

  Direct link is here

  http://ftp.HP.com/pub/SoftPaq/sp62001-62500/sp62425.exe

• Can't see the network hpsetup on my Macbook Pro on a C4780

  Help - I'm trying to get working wirelessly on a C4780 connected to a new Macbook Pro with 10.6.2.  I am on a network of wireless-G linksys with WPA_PSK and when the HP configuration utility try to connect to my network, it goes into "the network... search. "forever.  So, I tried to connect manually by some of the other posts, but I can't find the network hpsetup even after resetting to the default printer.  The serial number of the printer is CN99SD12ZF.  Is that printers with factory default SSID settings incorrect?  If so, what I try next?

  Some sent C47xx factory printers have an incorrect default setting in their non-volatile memory that prevents the method of ad-hoc configuration.  There is nothing wrong with the printer HW or FW and you should still be able to set up the printer using the Setup program on the CD.

  If necessary, it is a manual method to get the printer on your network.  Here's how to printers wireless C47xx:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  • Press the Scan button to get the wireless settings
  • Select wireless Menu
  • Select wireless settings
  • Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks and then Showall the bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  In the Web page of the printer, click Networking , and then select Wireless (802.11().  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.

• Windows 7 can not find the network

  Hi guys I hope that someone can help me, I walked trough the forums but none of the above helped me. I also do not really understand some of them. But that's what happened. My internet was fine yesterday, I was watching some stuff on aliexpress when my mouse froze, I tried to restart the laptop, but nothing worked so I had to remove the battery. After that the computer took forever to turn back and when he did my computer did not find my wifi more. I ran the following anti-virus, I tried the steps in the verification of all past system. I went in Sync Center, I have trid addition in manual, I tried to search for a wifi switch (I don't think I have a) I tried to restart the pc and the internet, I tried the system restore, I don't really know what else to do. Any suggestions?

  Hi Kate,.

  Thanks for posting your query in Microsoft Community.

  I understand that Windows 7 can't find the network and I appreciate the efforts made to try the patches. Let me ask you;

  • Restoring the system led?
  • What exactly happens when you try to connect to the Wi - Fi?

  This could be due to several reasons, including any third party software conflict. Try the following methods and check.

  Method 1: Start the computer in Mode safe mode with network and check if the problem persists. If the problem does not persist in SafeMode with network, put the computer in a clean boot state and check.

  Step 1: Start the computer using safe mode with networking

  Safe mode with networking is an option of troubleshooting for Windows that starts your computer in a limited State. Only basic files and drivers needed to run Windows are started. Safe Mode with networking appears in the corners of your monitor to identify which Windows mode you are using. You can use the internet connection in this mode.

  Please refer to: , start your computer in safe mode

  Step 2: Perform a clean boot in order to avoid any conflict of third party software.

  To help resolve the error and other messages, you can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Place your system in the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  Note: see 'How do I reset the computer to start normally after a boot minimum troubleshooting' to reset the computer starts normally after troubleshooting.

  Method 2: Update the network adapter

  Step 1: Update the driver through Device Manager

  a. click Start , type Device Manager and click on it

  b. expand network adapters

  c. make a right click driver, and then click Update driver software

  Step 2: Install the Windows updates pending

  To check the updates:

  1. Open Windows Update by clicking the Start button . In the search box, type Update, and then in the list of results, click Windows Update.

  2. In the left pane, click check for updates, and then wait while Windows searches the latest updates for your computer.

  3. If you see a message telling you that important updates are available, or you say to look at the important updates, click the message to view and select the updates to install.

  4. In the list, click the important updates for more information. Select the check boxes for the updates that you want to install and then click OK.

  5. Click install updates.

     Read and accept the terms of the license and then click Finish if the update requires it. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  Step 3: Visit the computer manufacturer's support Web site and install the latest network for Windows 8 for the same model of device drivers.

  Additional information:

  Wireless and wired network problems

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Problem of password of account, without that we can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid.

  Hi, I hope you can help with this problem. A friend has 6 computers networked to a Tower Server and have a problem. A worker student put computers into hibernation, and since then, nobody can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid. I tried to get into the pc to try removing network and replace it, but I can't get on the Administrators account because it has been disabled. I'm at a loss on how to proceed. My friend cannot afford a service call, so I'll try to help him.  Thank you

  If the computer is on a domain then there are at least two accounts that can be used to remove the computer from the domain:

  • A domain administrator account.
  • A local administrator account.

  When your friend has launched Windows for the first time after buying the machine, he was prompted to enter the name of an account. This account is created automatically with administrator privileges. He should use it now.

• My computer has virus of the FBI, I wiped it is clean but now it cannot connect to intermet because it can't find the network driver how can I find it?

  My computer has virus of the FBI, I wiped it is clean but now it cannot connect to intermet because it can't find the network driver how can I find it?

  Since you have formatted the PC and reinstalled Windows, your question will be handled better in the hardware forum space and drivers for Windows 7, so I'll move it there.

  Apparently, you need to install the driver of your PC network. If you used the CD to restore the PC manufacturer that should have been included, but it may be on a 2nd CD with drivers and programs.

  If not, the first thing to do is contact the PC manufacturer to see if they have a driver available for download. If the PC has a wireless network card and wired, perhaps one has been configured, but not the other and you try to use the not yet detected and installed.

  -steve

• How can I change the "network protection" off to on?

  How can I change the "network protection" off to on?

  If you ask about network access Protection, see this:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-security/how-to-turn-on-network-access-protection/7daeddb9-f652-4fac-a3bc-e1234c928add

• How can I change the network address of my Time Machine drive?

  Hi people,

  This is my second question in 12 hours. Thanks to help I received here, I abandoned my doomed attempt to use my old AirPort Extreme and a USB key for Time Machine backups.

  I've used my ReadyNAS for Time Machine backups, but it has never been reliable. I think I have tracked the question and I would like to try again. However, Time Machine remembers the old network address for the ReadyNAS unit (smb://NAS_TimeMachine.local/ReadyNAS) and does not 'see' the same unit at current address (afp://[email protected]/NASTimeMachine). You could collect that networking is not something I understand.

  I think that this can be also responsible for the boring 'There was a problem... "messages that I receive at startup telling me the drive could not be mounted.

  Is there a way to force the time Machine to forget the old address and 'see' a new?

  See you soon,.

  Grant

  (PS I have also posted this question on the legacy of networking community, but I think it's a better place for this)

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click select drive

  Click on a disc that appears under the heading of backup discs , so that it appears highlighted

  Click remove disk

  Do the same for all the other disks that may appear under the heading of backup discs

  Turn off and restart the AirPort Extreme

  Restart the Mac.

  Click the 'clock' Time machine at the top of the screen

  Click Open Time Machine Preferences

  Click select drives

  Under the heading of available records , click a disk that you want to use to highlight the disk

  Click use the disk

  Close the windows

  Wait a few minutes to see if a backup will start. Otherwise, click the "clock" Time machine at the top of the screen, then click on NTI Backup Now

  Report on the results

• How can I change the network to a WiFi connection profile in Windows 8?

  When I connect to a wireless connection, it automatically assigns me for the Public Profile. But, I know to trust the network and want to select it as private, so that I can use the share.

  In previous versions of Windows, it was easy to change the WiFi profile. For example, in Windows 7, I would go to the network share and click on the name of the profile, and it would allow me to change it. Now, in Windows 8, the profile name is static text and is no longer provides a link that allows me to edit the profile.

  I tried to remove the profile and add it back, using the context menu on the WiFi network and "forget this network". But he never asks on the profile or sharing when I add the network.

  Try this:

  -Show the charms

  -Select settings

  -Select the network icon

  -Right click (using a mouse), or press and hold (with your finger) on the name of the network connection, that you care

  -A menu will appear to allow you to control the sharing, so to go from a private and public profile.

• Where can I download the network drivers / wireless for my Satellite Pro L300?

  Hello.

  I reformatted my laptop from Windows Vista to Windows XP Professional SP3 and it never came with the network drivers / wireless to connect to the Internet.

  I tried to go on the Web from Toshiba site, which is the manufacturer of the laptop, but when you type in my model that is pslb9e-02v003en (L300-1FJ) it basically says that there is no such thing.

  I also tried to Google it but had a real hard time to his research... Where can I find my network/Wireless drivers so my laptop can detect my internet! Help, please!

  I ve checked the download page of Toshiba and support for Windows XP Home edition.
  I found the driver LAN here.
  WLAN driver can be downloaded from the Toshiba WLAN portal - http://aps2.toshiba-tro.de/wlan/

  Your laptop has Realtek WLAN card so please download Realtek WLAN driver Toshiba WLAN on download page.

  I hope this will help you.

  Please post comments.