Cannot access router Readyshare

Similar Questions

• Cannot access router wi - fi remote intelligent service said router offline.

  I can't access router remotely by using smart WiFi. When I connect it says router is in offline mode. Wrt1200AC. Used to work and now it doesn't. I have an account setup smart wi - fi. I can connect locally on my network. I went to troubleshooting, diagnosis, status and clicked on report. It shows that smart wi - fi service is stopped. How to start the service or connect. Everything else works fine.

  We have exhausted all possible solutions for our final step is to reflash manually its firmware. If all else fails, we will have it carefully studied by our team of level 2. Please send us an email to [email protected] with your file number, community username and link to this post for reference.

  Ann_18678
  Linksys technical support

• Cannot access router EA3500 to change settings

  I would like to make a few changes to the configuration of my router, but can't access the configuration screens. I tried Smart Wifi and myrouter.local.  After entering my password, it hangs on "Waiting."... "and I never have to the configuration screens.  What I am doing wrong?

  Hi there, lindsayla18! It is possible that the IP address (192.168.1.1) of the EA3500 may have changed. You try to access the wireless user interface? It is preferable that you access with the cable from the computer to the router.

  Try to get the IP address and the default gateway ('router' for Mac) of the connected computer and use this default gateway to access the user interface.
  Last resort would be to reset and reconfigure the EA3500. You still have to, do it connected to the router.

• Cannot access router after support call

  Support has changed the password of my router. I can see is more settings. What I have to do a complete reset to get it back?

  Disconnect the modem entirely.  Connect through the wire of your computer to a LAN port.  Press and hold the button of reset for 30 seconds and then release.  Wait 10 seconds and cycle power to the router.  Go to 192.168.1.1 with your browser, the connection empty user name, the password "admin".  Try now.

• Cannot access router page... any ideas

  I am running Snow Leopard on a MacBook Pro.

  I just updated my wrt110. Everything goes well until I restored my config.bin file.

  All my configs seem to have disappeared (password!). But no problem, I thought. I'll just go and put a new one.

  To my surprise, when I try to go to my IP (I see it on my network system preferences) I get thrown into a kind of a page of search with the following URL:

  http://websearch.Linksys.com/error_redirect_site/get_error_redirect?eg=1607625782&job=192.168.1.1/

  No matter what I have on any browser (I tried Firefox, Safari and Google Chrome) I get the same results.

  My router has lost the ID (now appears as the linksys just without password). I could fix it if I could barely get my order page.

  I searched all the help pages, but nothing tells me what is happening.

  Can anyone throw me a line on that?

  Thank you.

  Think you need to reset your router by pressing the reset button at the back of the router for 30-40 years years when it is turned on, after connect computer to the temporary router in this way, connect to the management page of the router with username/password default username and reconfigure the router by taking a look at this example of router configuration.

  Linksys router

  by default the user name: (leave empty)

  password: admin

  I hope this helps.

• Cannot access 'route '.

  I'm an illustrator tutorial, but got stuck.

  In the tut, an ink drawing is scanned in illustrator and vectored by using "tracing". Then the image is colored as follows:

  "I started coloring by creating a single shape that filled the whole of creation. I did this, just make a copy of my drawing vector line, select it, and then doing the following: object > compound path > release, then object > ungroup, then Pathfinder > add to the area of the shape. Basically this process broke up all these pieces of vector, then merged them into a single form. »

  http://www.gomediazine.com/tutorials/go-media-rapid-fire-illustration-technique/

  Here's my problem: I am a copy of the drawing to vector line, select it, however when I click on 'object', 'path' option is not available to choose. Where am I wrong?

  See you soon,.

  Erin.

  Have you tried new object--> Expand? Also try to run unbundle several times. Live webcam of trace creates strange group, which is not always logical in regard to this that things go together visually...

  Mylenium

• WRT110, Vista, wired desktop cannot access utility based on the router's web

  Computer Vista hard wired to the WRT110 cannot access the router. But it CAN get to internet and CAN ping router without losses. The XP machine is wireless, can get internet and CAN ping router without losses, but also can NOT access the router page. Ipconfig displays 192.168.1.1 is the correct default gateway address.  Yesterday, I had to reset the modem to access the router and had to enter all the parameters.  Could access router yesterday but can't today. The IP address is valid from yesterday to tomorrow. I don't understand what has happened to prevent access to the router. I even unplugged the modem to the router and still cannot access router today.  I can't find this problem in the forum, hope this isn't a duplicate request. Thanks for any help

  I have NO idea why, but I can access the Web with IE8 installed utility pages.  Has absolutely no sense to me.  Of course, it must be some kind of safety but my IE use medium-high settings, so I can't imagine what passage of IE7 to IE8 did indeed these parameters.

  Happy now that I can access these pages, finally.  Hope this helps someone else.

• Cannot access the internet (table routing and connection seems to be very well)

  Hello

  I have a problem that I can't know at the present time.
  The problem started after uninstalling cisco anyconnect vpn.
  Description:
  cannot access Web sites or even the router configuration panel
  cannot tracert beyond the first jump (router)
  can ping to ip Internet addresses
  routing table appears to be well
  After disabling all services additional error is always persistent
  computer is connected to the router cable
  So, it seems that something is blocking the connection, but I can't understand what...

  It fixed to the help of netsh winsock reset catalog and restart...

• Cannot access my router through the Explorer configuration page

  I need to do a port forwarding on my router. My internet connection works (even if she falls occasionally) and I can also connect to other computers on my network. However, I cannot access my router through IE page (I get a message saying: page not found). When I go see the map in the options Vista network, the router is not displayed and when I clikc on "See the whole map", I get a message saying that Windows cannot detect any computer or devices.

  My connection to the router is connected, and it is a WRT54G Lyinksys. Any ideas how I can see my router or go to its page layout? Another thing, I went to CMD and the ping command returns a default gateway 192.168.1.1, which is what I have my using the address of the webb page.

  Thanks for any help.

  Hi JBHPUser,
  
  (a) other router configuration page, you are able to access other Web sites?
   
  (b) what operating system and Internet Explorer version do you use?
   
  This article can be very useful.
   
  You receive an error message in Internet Explorer: "Internet Explorer cannot display the webpage".
  http://support.Microsoft.com/kb/956196
   
  You can also access these links, which is primarily for Windows Vista, but are also applies to Windows 7
   
  
  Solve problems with computers not appearing is not in the network map
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-computers-not-appearing-on-the-network-map
   
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
   
   
  
  Aziz Nadeem - Microsoft Support

• HP 15 laptop: laptop computer is connected to the wi - fi connection, but cannot access the internet

  Hello

  My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?

  Thanks in advance.

  Hello @jerome256,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I understand that you are having a problem with your WiFi and wanted to help you!

  You are trying to access WiFi through router?  If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router.  Check that the router is connected to the internet.  If you have more than one router, then you can ensure that you are connected to the correct router.  You can also try unplugging the router for about 30 seconds, and then reconnecting it.  Please consult the following document, as it can help solve the problem for you:

  HP PC - Troubleshooting wireless network and Internet (Windows 10)

  Please let me know if this information has been helpful by clicking the thumbs up below.

  Have a great day!

• Cannot access the gateway/DHCP WS2012

  Hi all

  For some reason any Windows Server 2012 machine cannot access my gateway (router). I got a new modem/router ATT (NVG589) so I got rid of my dlink router DGL4500. For some reason my server cannot get an IP from the DHCP on the router (windows is currently giving a private ip address). The dlink gateway is 192.168.0.1, and the new is 192.168.1.254. I have tried to put a static IP address, flush the dns, set it to automatic and searched online, nothing seems to work. When I plug the dlink again, the server is able to get an ip address from it. Am I missing something that I must specially configured in the NVG589? or y at - it something on the server, I need to change?

  Hello

  For questions on Windows Server 2012 you can post your question to the TechNet forums. They will be able to guide you to the best.

  https://social.technet.Microsoft.com/forums/WindowsServer/en-us/home

• Cannot access Time Capsule and MacBook Pro on Windows task force immediately after upgrade to Vista professional professional 7

  I had a Windows workgroup for years, linking the PC and Mac, but also a Linkstation network through a Time Capsule router/Hard Drive Combo.  Immediately after the upgrade from professional Vista to 7 Professional on my Sony Vaio VGN-Z750D, I can see the Time Capsule and MacBook but cannot access it.  I am able to access the Linkstation - system wonder a user name and password, and I have immediate access.  However, the system does not n = me a username and password when I try to access the two Apple products.

  Interestingly, I can access the Vaio MacBook, in providint the username and password for the Vaio.

  Please notify.  Thank you.

  IT FIXED!  Found the answer on the W7 Forum

  Access to Mac OS X Windows sharing Windows 7
  Windows 7 will not work with the Mac OS X Windows support for default share file. If you try to access a shared folder on Mac OS X, W7 will display a logon error repeatedly.
  The problem is that W7, by default, will only use NTLMv2 for authentication, which is not supported by the service of sharing of Windows of Mac OS x.
  The other problem is that safety minimum Session for NTVLM SSP based Clients.
  To work around this problem:
  1. in W7, open the control panel
  3. double-click on Administrative Tools
  4 double click on local security policy
  5 expand "Local policies" and select "Security Options".
  6. locate "network security: LAN Manager Authentication Level" in the list and double-click it.
  7. change the setting of "NTMLv2 only send responses" to"send LM and NTLM - use NTLMv2 session if negotiated"
  8. network Security: minimum session for the NTLM SSP (including secure RPC) Clients security
  9. change the setting of "128-bit" unchecked (No Minimum)
  10. click on OK

• I cannot access internet Windows XP.

  Hello

  My name is Tommy and I need help. My desktop computer shows that it is connected to the internet, but when I try to use any application that requires the internet (IE, firefox, chrome, League of legends, etc..) I get a 'connection error' / Web page isn't reachable. Internet works on my parents and my sisters computer, so I don't think it's a problem with the router (even if they're using wifi). My firewall will not turn on either. I tried a reset winsock, but to no avail.  I ran a few antivirus scans and eventually find a sitting trojan.muldrop in my System Volume Information folder, and I deleted it with by Dr.Web CureIt. After the removal of the virus, my computer will still not access the internet, and I can't turn on my firewall. Please help if possible!
  Thank you!

  Original title: my computer says it is connected but cannot access the internet.

  Hi Tommy,.

   

  Please contact the Microsoft Community.

   

  I would have you look at the article-

  How can I reset the default Hosts file?

  http://support.Microsoft.com/kb/972034

  Do get back to us and let us know. We will be happy to help you.

  Thank you.

• Dell has developed a passwoord and cannot access the Windows XP system on a network share in Windows 7.

  Original title: network router, XP computer and Windows 7 laptop computer dilemma.

  My system XP computer is part of a network using a router. I also have a laptop Windows 7, using the same network. Reference Dell set up a password so that the network is not accessible without password, reducing the risk of piracy. Now, I can not in the XP system because of the defined password.  How to reset or enter the password on the XP computer?

  Hi Scottid2,

  1. do you receive error messages when you access the Windows XP system?

  2. What is the password being set by Dell?

  You can check in the Windows 7 system if the password protected sharing is enabled. When protected by password sharing is enabled, people using other computers on your network cannot access your shared folders or printers unless they have a user account on your computer.

  You can turn off password protected sharing and check if it helps.

  For more information, see the articles:

  Why can't I connect to other computers?

  Networking of computers running different versions of Windows

  As the password is set by Dell, you can also consult with support of Dell for the same thing:

  Dell support

• Cannot access the internet on a network Windows XP when Windows 7 goes to sleep

  Original title: Windows 7 Windows XP network problem.

  I replaced a Windows XP computer on my node 4 (2 PC, printer 2) cable network with a Windows 7 computer.  When the Windows 7 computer in mode 'sleep' the other (XP) computer cannot access the internet.  A message appears that there are 2 computers with the same IP address.  If I wake the computer 7 fine.  That is what it is?  I agree not all files between the computers.

  Hello

  It is usually the case when, for example, a router is off, but one or more of the devices connected to the router are left on.

  The devices to retain the ip address assigned to them, but when the router starts up again it has no knowledge of this. If when you start one of the other devices, the router can assign an ip address already in use. Concrete example that I reproduced with my router and the PC...

  • Start the router, then boot PC1 and PC2 - the router (192.168.1.1) will allocate for PC1 192.168.1.2 and 192.168.1.3 to PC2
  • Turn off the router, then turn off PC2, restart and shut off again
  • Put the PC1 to sleep
  • Start the router and PC2, the router does not PC1 and allocate 192.168.1.2 to PC2
  • PC1 to wake up and there still 192.168.1.2 who now is a confrontation with PC2

  Other ways to reproduce this situation may also be possible.

  All devices on your network must have a unique ip address, where the warning message.

  If you get this situation once again, the solution is to turn off all devices, including the router, then restart the router, then restart all devices connected to the router.

  To avoid this, you may be able to put ip Reservations for your router address which will ensure that all devices connected to the router always get the same ip address (unique). If you are unsure how to proceed, we will need your router brand and model to help.

  Tricky