Cannot add the RT Watchdog subpalette

Similar Questions

• Cannot add the printer network Windows 7 64 bit

  My laptop Home Premium 64 - bit of Windows 7 (client) cannot add the network printer that sits on the Windows 7 Ultimate 64 bit computer. A client XP computer easily added the network printer. When you try to add the network printer, the Windows 7 client searches for the driver on the host computer and says "unable to connect to the printer - the operation has failed with error 0x000003e3. I downloaded the driver from the manufacturer of the printer to the client computer. I also disabled the firewall on the computers... Any help would be appreciated.

  Hello

  ·         What is the number and model of the printer that you are using?

  ·         How many computers are connected to the host computer?

  ·         You are on a domain network?

  Method 1:

  You can check the items below that explain how to install a printer in Windows 7.

  Install a printer

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

  Find and install printer drivers

  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  Method 2:

  a. now follow the document below to add the printer to the Windows 7 computer.

  http://Windows.Microsoft.com/en-us/Windows7/share-a-printer

  b. If the steps above does not help try the procedure below.

  We need to change the port and check. Let us perform the steps below to install this printer and check.

  a. Click Start, click Control Panel, and double click on devices and printers.

  b. click Add a printer.

  c. Select "add a local printer.

  d. Select "create a new port". Select "Local Port" as the port type.

  e. in the "type a port name" box, type the address in the following format.

  \\[IP address of the host computer]------[the share name of the printer]

  And then click Next.

  f. Select the driver in the list of drivers. If no driver available, click the Windows Update button, wait the process finishes and then search for the driver again.

  g. complete the installation.

  For additional help, refer to the article below.

  Printer in Windows problems

  You can also check out the link below that addresses the same issue when you face:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/error-0x000003e3-when-trying-to-install-network/2348b57b-7448-E011-8dfc-68b599b31bf5?msgId=d577ab02-DC48-E011-8dfc-68b599b31bf5

• get the 1726 error: cannot add the port monitor

  get the 1726 error: cannot add the port monitor hp discovery port monitor (hp photosmart 5525 series) running Windows XP, HP Photosmart 5525

  Could not complete the installation.

  Hi Jeff,

  The computer manufacturing must have created a partition on the disk or provided you CD to restore the computer to the way it was when you bought it. If you have a PC clone, then probably you need to reformat your hard drive and reinstall the operating system. If you have an OEM computer (example: HP, Dell, ETC) there is most likely instructions when you turn on/off press F11 or F12 to return the computer to the computer.

  Note: Do nothing until you have all of your backup data.

• Cannot add the header HTML - CFWebstore on CF11

  Hello

  I get the error below on a new installation of CFWebstore v6.6 on CF11. I used a previous version of CFWebstore on CF7 and CF9 without problem. Looking for suggestions...

  Cannot add the HTML header. ColdFusion is unable to add the header specified in the output stream. It's probably because you used to define one of the ColdFusion Cookies of Session or authentication cookie. To do this, please use configuration at the application server level. The error occurred on line 213.

  Thanks in advance for any help!

  Gary

  I found this answer:

  To resolve this issue, connect to Coldfusion Admin, go to the memory Variables and uncheck "Disable the update from Coldfusion cookies using tags/functions of Coldfusion." Memorize your settings, and then restart your Web site.

• Cannot add the vmkernel nic: a specified parameter was not correct. vSphere CLI + ESXi 4

  Hello. I try to add vmknic with frames in my distributed virtual switch.

  I read the vSphere command-line Interface Installation and reference Guideguide:

  "vicfg-vmknic - a-i DHCP"vmk5"

  I see the error message:

  Cannot add the vmkernel nic: a specified parameter was not correct.

  Vim.Host.VirtualNic.Specification.Ip

  What's wrong?

  I tried all the combinations of parameters with the same result.

  Ok! I've found a workaround.

  Since adding a vmkernel remote interface doesn't seem to work with DVS, I simply created one on a standard vSwitch and it then migrated to the DVS. And voila: the value 9000 MTU migrated intact with her! Here are the steps I followed:

  1. put the ESX host into maintenance mode - evacuate VMs manually if necessary

  2 remove the VMKernel iSCSI/NFS to the DVS interface

  3. create a standard virtual switch with no physical cards. He has no need to be a VMKernel VM Networking switch is fine. Make a note of the name you gave to the PortGroup created on the new vSwitch.

  4 using the remote control line, add the new interface vkernel specifying an appropriate jumbo MTU (9000) and the PortGroup on the standard new vSwitch. For example:

  esxcfg - vmknic.pl - Server

  If you get 3 answers, everything works. If you get failures, something has gone wrong. Go back and check that the interface is configured correctly using the command list esxcfg - vmknic.pl-.

  Enjoy!

  M

• Cannot add the new log file for the 11g database.

  Salvation of DBA
  
  I'm not able to add the log file, I receive the error message when the database is added.
  
  SQL > alter database add logfile group 3 ('/ oracle/DEV/db/apps_st/data/log03a.dbf','/oracle/DEV/db/apps_st/data/log03a.dbf') Re-use of size of 50 m;
  alter database add logfile group 3 ('/ oracle/DEV/db/apps_st/data/log03a.dbf','/oracle/DEV/db/apps_st/data/log03a.dbf') Re-use of 50 m of size
  *
  ERROR on line 1:
  ORA-01505: Error adding log files
  ORA-01577: cannot add the log file ' / oracle/DEV/db/apps_st/data/log03a.dbf'-fichier
  already a part of the database
  
  SQL > select a.group #, a.status, a member of the journal of v$ a, v$ logfile b where a.group # order of b.group = # 1;
  
  GROUP # MEMBER STATUS
  ---------- ---------------------------------------- ----------
  1 ACTIVE /oracle/DEV/db/apps_st/data/log01a.dbf
  1 ACTIVE /oracle/DEV/db/apps_st/data/log01b.dbf
  /Oracle/DEV/db/apps_st/data/log02a.dbf CURRENT 2
  /Oracle/DEV/db/apps_st/data/log02b.dbf CURRENT 2
  
  Kindly help me to add the new log file to my database.
  
  Thank you
  SG

  PGO

  Please see (how can redo log group be dropped when it ever becomes inactive?) [ID] 730827.1).

  Thank you
  Hussein

• Cannot add the program to enable the WIndows firewall

  I try to install Peachtree Accounting 2011 and firewall Windows gives me a message «firewall WIndows cannot add Peachree accounting 2011»

  to the exceptions list", so I can't install the program.  I tried almost everything.  Not very technologically trained but can follow instructions well.  Thank you

  Here is a fix for this problem:

  Tweaking.com - repair Windows Firewall 2.8.8

  http://www.MajorGeeks.com/files/details/tweaking_com_repair_windows_firewall.html

  I had a customer with the same problem - cannot add programs, and the link above has solved the problem.

• Cannot add the partition to an existing table.

  Hello

  I don't add the partition to an existing table that is not partitioned, get the error as a type of data not valid, then I'm not find syntax errors.

  ALTER TABLE MESSAGEX_XCHANGE

  ADD THE PARTITION OF RANGE (LAST_MODIFY_TIMESTAMP)

  (

  PARTITION old_data VALUES LESS THAN (To_TIMESTAMP('27/02/2014','DD/MM/YYYY')),

  You see for VALUES LESS THAN (To_TIMESTAMP('28/02/2014','DD/MM/YYYY')) of the PARTITION

  );

  Error report:

  SQL error: ORA-00902: invalid data type

  1. 00000 - "invalid data type".

  * Cause:

  * Action:

  Thank you

  Manon...

  You get this error because your edit statement has an invalid syntax. In addition, you cannot partition a table that is not already configured for partitioning!

  You have to physically re-create the partitioned table in order to add new partitions to it.

• vifp addserver fails with the error cannot add the user

  This my first post on this forum that I couldn't find an answer via Google search. If I do not use correct terminology or fail to provide comprehensive information, please forgive me. I'm not an expert on VMWare, just a passionate curious tech. I found VMWare to be a very exciting and easy to use product. The VMWare knowledge base is excellent and so is the community of users.

  I have install VMWare ESXi 6.0 free House on servers Dell T420 and T110 II. I recently tested vMA 5 by installing it as a virtual machine on one of the servers. I watched the tutorial Youtube how to use vifp to add servers. I have network etc. on vMA installation and it works fine. Automatic update worked. I issue the command sudo vifp addserver 192.168.250.96, I am prompted for the password. When I enter the password, I get an error error: cannot add users. I checked the log file in /var/opt/vmware/vma/vifpd.log and the more descriptive message is:

  addServer: error occurred when adding users for 192.168.250.96... roll back. An error occurred during the creation of users on 192.168.250.96

  Then I noticed that since I'm on the console vMA to run these commands, as soon as the error occurs, I see that in the lower part, under recent tasks, I see an error: General system error: weak password. The details of the error says:

  

  Weak password: not quite different characters or classes.

  Now my password is strong enough. I can't post it here but I'll post a similar password:

  4518Gabdhjg #01

  It is 14 characters and has the numbers, letter uppercase, lowercase letters and special characters. I read the VMWare documentation on passwords and for me, the password seems very well. Any help will be appreciated.

  Thank you

  Arun Gupta

  My bad. I didn't know that vMA 6.0 is available. I just downloaded and configured vMA 6.0 and the problem is solved. Sorry for disturbing everyone.

• Cannot add the NFS share to store Cluster data

  Hello

  I have this scenario:

  Server - FREENAS with NFS share

  -cluster with 2 guests

  I added the NFS datastore successfully to each host in the cluster. The problem is when I try to add the NFS Datastore for the Cluster data store, I get the error: a specified poarameter was not correct. datastore.info.type.

  Any suggestions would be much appreciated.

  Thank you.

  Datastore1 and datastore2 data warehouses are data warehouses local? If so, you must remove these storages of data added before the NFS datatore to the cluster, first cause a cluster cannot be VMFS and NFS on the same cluster and second cause without making sense have warehouses of local data within a cluster data store.

• cannot add the new hard drive more than 2 TB on vsphere upgrade 5

  can someone give me a clue? I can't add new greater than 2 TB drive to my vm on my upgraded vsphere 5.0. My data store is 6 TB and already read by vsphere... I create new virtual machine and add the new drive, but it limits again just 2 TB when I change 4 TB, the error message will appear. I recently added my datastore LUN with VMFS5 version. is there a any mistake I made? Please help me this problem is so frustrating me... i need to create new disk 6 TB to my new file server

  Hello.

  You will need to use a RDM in physical Compatibility Mode to achieve. As weinstein5 said, a VMDK cannot be greater than 2-to-512bytes. You can use the OS to spread over several 2 TB-512bytes VMDK, if that's what you really want.

  Good luck!

• Cannot add the new printer port for Central Output Server 5.7 under Windows Server 2012

  I am my output of an old Windows box to a new server migration and have problems with the new ports.  I have 6 installed instances and the last looks OK, but all the others get errors when all output is sent to them, even a Windows Test print. I have them all the same thing, with the format \\.\pipe\jetform\server5 configuration port

  When I installed the software, I installed all 6 instances then went through and added 6 local printer ports - it seemed to configure them OK this first time.

  My test was then on the 6th and last instance and went well.

  When I wanted to test the other forums, I found all simply erroneous jobs on the queue for the printer.

  If I have one of these printers connected to the 6th port, it worked fine.

  I deleted one of the ports that did not work and I tried to re-add. Then I got the message "the system cannot find the file specified."

  I tried to add the port via the registry - he added, but would not yet print.

  Then I noticed in the output server control center, when I tried to stop Central and start one of them, I got the error "unable to connect to the channel named"\\.\pipe\jetform\server5.ctr"

  I use a domain account that is configured to run Adobe services, he is a Director of field with all required fees

  I modified the local security policy to enable users to add printer drivers.

  And I have now run out of ideas! Someone at - it a?

  Thank you

  This was traced to one of still having ini files a record of the proceedings of last name installed (i.e. SERVER6).

  So it's fixed

• Cannot add the Flash disk

  Hello

  I came into work this morning to find one of our servers in a State that won't start plu.

  This virtual server is hosted on an ESXi 3.5.0 123629 server with two data warehouses.

  The following error occurred when trying to start the server.

  Please check that the path is valid and try again. Cannot open disk 'path to the file DEVSQL1_1 - 000001.vmdk' or one of the snapshot disks it depends on. Reason: The system cannot find the specified file.

  When you browse the data store, I could see the vmdk file.

  I learned later that the DEVSQL1_1.vmdk file has been moved to the another data store.

  Unfortunately, at this time, I removed the hard drive that was pointing to the file - 000001.vmdk if I could add a new hard disk that points the moved file from DEVSQL1_1.vmdk.

  Server started the first pop, except that the data stored on the disk problem are old.

  At this point, I stop the server and moved the DEVSQL1_1.vmdk file to its original location. Then, I removed the disc newly added and tried to add a hard drive pointing to the original DEVSQL1_1 - 000001.vmdk. When you do this I get the error "object reference is not set to an instance of an object" and I am unable to go further.

  When open the Snapshot Manager, I am unable to see relating to this disk snapshots.

  Anyone know how I can join the DEVSQL1_1 - 000001.vmdk disc in order to start the server and also have access to current data?

  Thank you very much

  Glen

  Glen - I don't think we should use this DEVSQL1 - 000001.vmdk snapshot

  I have no evidence that it has been used in the history of this virtual machine.
  It does not fit to the size of its parent disk.

  Do you remember if DEVSQL1.vmdk has been developed in the history of this virtual machine?

  Edit the vmx and change

  scsi0:0. FileName = 'DEVSQL1 - 000001.vmdk ".
  TO
  scsi0:0. FileName = "DEVSQL1.vmdk".

  It was also the State used when the machine virtual last started successfully.

  Honestly, I was a little surprised when you found this DEVSQL1 - 000001.vmdk

  You have an idea about this?

  After editing the vmx file the VM must start - when starting carefully inspect the condition = if it is out of date turn off directly.

  I doubt you'll see an out-of-date status - but if the first disk is expired I must expand the snapshot - that would be a bit strange

• Cannot add the debit card to Apple Watch

  I discovered lately that my Apple Watch does not have to pay for Apple.  I deleted the card from my iPhone 6 and added with no problems, but when I try to add the same card to my Apple Watch, it fails with the error pop up not added card - Contact your issuer of the card for more information. Add card later or try again.  I'm with Lloyd's bank, to the United Kingdom and do not understand why it seems to work on the iPhone but not the watch.

  Try to set up Apple pay on Apple Watch as described in the article configure Apple pay on your iPad, iPhone, or Apple Watch - Apple Support

• Cannot add the Google account

  I am trying to add my Google account to synchronize contacts and calendars on my Mac. When I go to Internet accounts and add the Google account, I am stuck in the login screens. I entered the code sent a text message to my phone because I have 2 factor auth enabled, and I check the Contacts and calendars:

  

  When I click on done, disables the button and nothing happens:

  

  Any ideas on how to solve the problems? I don't know if there is a problem with the factor 2 auth or something else.

  Thank you

  Zach

  Accounts Internet does not not on the password for google accounts