Cannot configure network for POS

Similar Questions

• BBM cannot configure BBM for 9900

  When I hit the bbm, it says he "cannot configure bbm" (not enough wireless coverage or your connection to the wireless network is turned off)... so I can't click anything on the screen... Please help on what to do because almost 3 days that I can not use my bbm. Thank you...

  BlackBerry devices running BlackBerry OS7 (like your Bold 9900) and below require a data plan services of BlackBerry to use BBM.

• Cannot configure 7410 for wireless network

  I have a 7410 that I hooked up to a cable for several years but have just moved my office and need to set up a wireless network. Modem, router and computers are fine, but the printer does not have a wireless option, even if it is a wireless printer. I went to the help section and saw that I needed to hit the installer, 8 and 4, that is not problem, except in the network menu, I have only 1, 2 or 3.

  Does anyone know where is my 4 (wireless configuration)?

  Return to the Ethernet cable option - your Windows machine will complain of limited connectivity, but it's OK.

  Once your computer gets an IP address (it will be in the form 169.254.x.y), then open web page internal printer by accessing its IP address.  Select network, wireless (802.11) and then advanced.  Activate the wireless link and click on apply.

  If you do not find the wireless section of the 7410 internal web page, then your printer is ignored and is not a radio.

• Re-install Windows 7 from Dell reinstallation DVD fails with "cannot configure Windows for your hardware.

  I have to do a ground up to Windows 7, re - install media re-installing Win7 provided, due to the failure of the hard drive (so no available recovery partition).  The machine is a XPS 9000 (circa 2010).   The first phase (partitioning, file copy and extraction) works very well.  However, when I restart in Windows for the first time since the hard drive, I get a message that Windows install can not configure Windows to my hardware.  The only option is to recognize and to restart (which gives the same message).  Subsequent reboots just to say that the Windows installation cannot be completed and restart to install Windows.

  Clues to this topic?  I have no new hardware in the machine which would be incompatible with this disc to re - install (admittedly old and probably non - SP1).  I wonder if the drive is missing in fact support that they put in the installation image factory.  My next step is to get a Dutch Win 7 installation disc (probably with SP1) to see if it works.  Other thoughts?

  Belarc Advisor only gives you the product key of the registry which, for installation OEM Dell will be a SLP key. This will be different from the key on the COA and can be activated manually by entering it during installation.

  The key on the certificate of authenticity can be introduced during the installation and this activation requires a call to Microsoft.

  Key/OEM SLP activation can be applied to a retail facility without a product key by using the program and cert ABR files which I saved for installs with the Dell reinstallation DVD:

  http://dellwindowsreinstallationguide.com/a-clean-install-of-Windows/Microsoft-product-activation/the-activation-backup-and-recovery-program-Windows-Vista-7-version/

  Although Windows view (s) and begins to install it on the hard drive, it could be an art of hiccups the end with the HDD and loading SATA drivers can always solve this problem.

• error windows cannot configure network adhoc connection? win7home premium

  in network and sharing Center I select new connection > network configuration ad-hoc (computer to count) name network and fill all boxes and press enter then I get windows error could not set up 'network name' I adapter.plz wireless brodcome802.11g give me a solution a solution.thanks perfect

  Hello

  1. when exactly do you get this error message?

  2. have there been recent changes to the computer before the show?

  I suggest you to see link and check if it helps.

  Error message when you try to connect to an ad-hoc connection Windows 7 or Windows Vista: "Windows cannot connect to ": http://support.microsoft.com/kb/946481

  More information: Set up a computer-to-computer (ad hoc) network: http://windows.microsoft.com/en-US/windows7/Set-up-a-computer-to-computer-ad-hoc-network

  Hope this information is useful.

• Cannot configure wrp400 for service HyperDog digital...

  I just had a wrp400 and signed for HyperDog Digitial service... I thought that the configuration would be easy because the router part of the wrp400 is really nice, a setting up quick and very quick start.

  Anyway, I stuck the username / password / auth id / HyperDog digital (for the PAP2) site of numbering plan and... no dice.

  Are there changes to the numbering plan that need to be made... or what... (?)

  Any help would be appreciated.

  Make sure that the proxy settings is correct. If you have a router in front of these wrp400 then you need to forward ports on the router. Also try to see if changing the NAT mapping will operate.

• cannot configure Cocos2Dx for native development PlayBook

  Hello

  I try to install cocos2dx for playbook in native QNX Momentix IDE, I followed the instructions on

  http://www.cocos2d-x.org/projects/cocos2d-x/wiki/How_to_run_HelloWorld_and_Tests_on_BlackBerry_Table...

  but after importing when I build project (TestCocos2dX) to get the following errors in the console

  **** Rebuild of configuration Device-Debug for project TestCocos2dx ****
  
  **** Internal Builder is used for build               ****
  qcc -o main.o ..\main.cpp -V4.4.2,gcc_ntoarmv7le_cpp -w1 -IC:/bbndk-2.0.0-beta3/target/qnx6/usr/include/freetype2 -IC:/bbndk-2.0.0-beta3/target/qnx6/../target-override/usr/include -I../../ -I../../../ -I../../../cocos2dx -I../../../cocos2dx/include -I../../../cocos2dx/platform -I../../../cocos2dx/platform/qnx -I../../../chipmunk/include/chipmunk -I../../../CocosDenshion/include -D_FORTIFY_SOURCE=2 -c -g -fstack-protector-all
  ..\main.cpp:1:21: error: cocos2d.h: No such file or directory
  ..\main.cpp:2:25: error: AppDelegate.h: No such file or directory
  ..\main.cpp:4: error: expected constructor, destructor, or type conversion before ';' token
  ..\main.cpp: In function 'int main(int, char**)':
  ..\main.cpp:8: error: 'AppDelegate' was not declared in this scope
  ..\main.cpp:8: error: 'app' was not declared in this scope
  ..\main.cpp:10: error: expected type-specifier before 'AppDelegate'
  ..\main.cpp:10: error: expected ';' before 'AppDelegate'
  ..\main.cpp:11: error: 'cocos2d' has not been declared
  ..\main.cpp:12: error: type '' argument given to 'delete', expected pointer
  cc: C:/bbndk-2.0.0-beta3/host/win32/x86/usr/lib/gcc/arm-unknown-nto-qnx6.5.0eabi/4.4.2/cc1plus caught signal 1
  Build error occurred, build is stopped
  Time consumed: 208  ms.
  

  When I try to build cocos2dx had errors in Consol

  **** Rebuild of configuration Device-Debug for project cocos2dx ****
  
  **** Internal Builder is used for build               ****
  qcc -o CCCamera.o ..\..\CCCamera.cpp -V4.4.2,gcc_ntoarmv7le_cpp -w1 -shared -IC:/bbndk-2.0.0-beta3/target/qnx6/usr/include/freetype2 -IC:/bbndk-2.0.0-beta3/target/qnx6/../target-override/usr/include -I../../../ -I../../../cocos2dx -I../../../cocos2dx/include -I../../../cocos2dx/platform -I../../../cocos2dx/platform/qnx -I../../../cocos2dx/platform/third_party/qnx/include/grskia -D_FORTIFY_SOURCE=2 -c -g -fstack-protector-all
  cc1plus: error: ..\..\CCCamera.cpp: No such file or directory
  cc: C:/bbndk-2.0.0-beta3/host/win32/x86/usr/lib/gcc/arm-unknown-nto-qnx6.5.0eabi/4.4.2/cc1plus caught signal 1
  Build error occurred, build is stopped
  Time consumed: 185  ms.
  

  What is the problem that I did, or I forgot something to do, I googled but not found tutorials that may be useful...

  It is of great if someone from BB, or forum post a video YouTube video to complete the process is running a HelloWorld cocos2dx for playbook.

  :

  You get to use 'Copy projects into workspace' what import? I did this first, but the project does not include the source files, the actual source is not copied with the projects. You must keep the files in their original location (do not copy in your workspace) so they can be referenced from the project directory. After I did this change the project builds and runs correctly .

  This gives a try and let us know if it works for you then.

• Cannot configure FxV for FMS

  Hi all

  I'm trying to connect to FMS and FxV but its rout sending metric to the first FMS server and encountered following error:

  Impossible to send parameters to Foglight, error: the host did not accept the connection within the time-out of 30000 ms

  Could someone help me with this error?

  Find the attached screenshots of the FMS migration integration and configuration server.

  Kind regards

  Shiva

  Additional accessories:

  • 
    i.PNG

  Shiva,

  FxV will attempt to send data to the first IP address (you listed two FMS server IP addresses). If sending fails at the first IP address then FxV will attempt to send data to the second IP address. Data will be sent only to one of the two listed IPS.

  David Mendoza

  Foglight Consultant

• Configuration network LaserJet P1606dn

  Hello world

  I have a problem with establishing a new LaserJet P1606dn on our network. The installation software provided with the printer assumes the environment uses a DHCP server to obtain an initial IP address and then you can evaluate the printer through the web interface and change it. My problem, we do not have DHCP on our network and I need to set up an IP address on this printer. My question, is there any other utility that can be used to find the printer, and then set the printer with a static IP address.

  Thank you in advanced for assistance.

  Steven

  Too bad. I found another way to access the printer. It seems to have assigned the printer an IP 169.254.x.x wherein I changed my desktop to the same subnet and then access the printers web interface to configure networking for the correct IP subnet.

• When I go to my list of wireless networks, or try to connect to a network it tells me that windows cannot configure the network.

  Unable to connect because of firewall or something, not true of course

  When I go to my list of wireless networks, or try to connect to a network it tells me that windows cannot configure the network and if I wanted windows to set up the connection, I need to start the firewall/ICS internet service (ICS) service and then he asks me if I want to start now then I say yes , but then it just tells me that it can't because the assoiciated service is not running, can anyone help please.

  Hello

  I suggest you to follow the steps in troubleshooting this article and check if it helps:

  Error message when you try to run the Network Setup Wizard update for Windows XP Service Pack 2, Service Pack 3, or Windows XP Tablet PC 2005 Edition wireless

  http://support.Microsoft.com/kb/871122

  Also read these articles and check:

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

  How to troubleshoot wireless network connections in Windows XP Service Pack 2

  http://support.Microsoft.com/kb/870702/en-us?p=1

• Installed wireless Belkin, unable to see network, get error windows cannot configure this wireless connection and starting the WZC abuse

  Hello

  I have a belkin wireless router that worked on my primary computer and a portable computer for years.

  Recently, I moved my main computer and now it dosnt seem to work. Belkin is installed but when I ask to see available networks, it says that windows cannot configure this wireless connection and starting the WZC abuse. Belkin still works fine on my laptop so I know no there is not a problem here. Can someone help me please? I tried to type in %SystemRoot%\system32\services.mcs\s as with a question of people, but all I get is windows can't find this.

  Any ideas please?

  Thank you

  * original title - Help... problem with belkin wireless *.

  Let's see if I can cut through it.

  You wrote:

  Click the Wireless Networks (see this picture) - I did

  Is the box 'Use Windows to configure my wireless network' checked or unchecked? There is no such box.

  I connect using - he says belkin. another box saying this connection uses the following items. then underneath there are 3 tabs - install, uninstall and properties. If I press on properties it says name provider and in this box, it says windows index.

  It seems that you don't have not clicked the "Wireless networks" tab, after you open the properties of your wireless adapter.  From your description, you look at the 'Général' tab: click HERE to see the "Général" tab Click HERE to see the 'Wireless Networks' tab.

  There are 5 columns: name, description, status, startup type and log as.  The values for the last 3 columns should be started, automatic and Local System - on my screen there are 4 tabs at the top - general, connect you, recovery and dependency.

  You skipped a step... 5 columns are in the 'Services' window initial... you arrive at "4 tabs at the top", AFTER you double-click the Wireless Auto Configuration.

  Status of the service which includes 4 boxes. stop suspend and resume. the button highlighted in the start menu

  Just to the right of the expression "Service status", you should see a Word.  On your system, this word probably is "stopped."  The 4 buttons (boxes) are how to control the service.  Because you said that the highlighted button is 'start' which means that the service is currently stopped, and you will need to click on this button "start" to start.

  I strongly suspect that you had used the Belkin utility to control your adapter - and now, you also started WZC.  As I wrote above, you can have both running at the same time.

  When you click the icon of your "Belkin", do you have a screen that looks like this: http://www.wi-fiplanet.com/img/2006/belkinn1/08.jpg

  If so, you should return to the utility Services and 'Stop' the automatic configuration service.  If you want to use WZC instead of the Belkin utility, see http://en-us-support.belkin.com/app/answers/detail/a_id/40/related/1

  I'm not familiar with the Belkin Wireless networking utility, but many wifi manufacturer utilities can be used to turn your wifi on and off, then maybe your was off (the adapter on your computer - not the router).  If you identify the model of the card you have in your main computer, I'll see if I can find the manual on the Belkin website and maybe give you a little more information.

• When I remove my computer and try to connect to a different wireless network Iget "windows cannot configure the wireless connection" what can I do?

  My "wireless connection" screen does not show available networks, but gives me the message "Windows cannot configure this wireless connection".

  Should what changes I make to connect to different wireless routers?

  Hello

  You should try another network you know for sure that it is Public and open (as in the Starbucks or McDonald's).

  Wireless in general, http://www.ezlan.net/wireless.html

• Cannot display networks wireless range... impossible to start the Automatic Configuration service

  My wireless card says it works correctly, but when I try to choose a network I get "Windows cannot configure this wireless connection" and I'm not smart enough to understand how to start the automatic configuration service.

  Hello

  If there is no 3rd party utility running (as mentioned by Steve), or you disabled loan and lost WZC.

  Maybe this can help, http://www.ezlan.net/wzc.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Why am I not able to choose a wireless network? I get the message "windows cannot configure this wireless connection".

  Why am I not able to choose a wireless network. I get the message "windows cannot configure this wireless connection".

  When I go to network connections it shows: Wireless network Connection - connected, Shared Dell Wireless 1397 WLAN Mini - Card & connection 1394 - 1394 connected Net Adapter.

  How can I solve this problem.

  original title: 1394 connection?

  Hi ToddHenderson,

  You did changes to the computer before the show?

  Method 1
  I suggest you try the following steps:

  The error message can mean that your hardware manufacturer has provided you with its own software to wireless as an alternative configuration to Windows Wireless Auto-Configuration service.

  I suggest you follow the steps below.

  
  Use Windows to configure wireless settings
  a. go to the start menu, then select run
  b. type ncpa.cpl, and then click OK to open the menu of the network connections
  c. Select your Wi - Fi connection service and choose the option change settings of this connection.
  d. go to the wireless networks tab and check use Windows to configure my wireless network

  
  Launch Windows Zero Configuration
  e. return to the start menu and select run
  f. type % SystemRoot%\system32\services.msc/s, and then click OK
  g. double-click the Wireless Auto Configuration option
  h., go to the startup type list, and then click Automatic. Click on apply to confirm the changes
  i. Accordingly, click Start in the Service status section click OK to apply the changes.

  Method 2
  Try the steps from the following link:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Network configuration required for VIO with VDS integration

  You are looking for assistance with the requirements of network for a new installation VIO, I plan.

  Requirements, I see that it takes 3 VLAN

  API with 5 IPs

  Management with 18 IPs

  Provider with x IPs

  I plan this configuration will be in a network of laboratories. My plan is to use a subnet I can connect to in the laboratory for the vlan API I will need access to the dashboard VIO etc..

  For two other VLANs, I was going to use two private ip ranges

  My question is, pole management provide connectivity/routing between these 3 VLAN or do you need to configure a router out to route between the 3 VLAN?

  Any help appreciated

  Your layout looks ok and should be good.

  I don't understand what you mean by 'cluster management provide a connectivity/routing between these 3 VLAN... '. » ? The routing between these VLANS is up to you. VIO didn't need connectivity amongst these VLAN that is to say that they can be separated segments without any L3 L2.

  However, must the hosts in the cluster Management, be transmitted to each of these VLANs. See the section "Physical networking" in the little quick start guide more color on the L2/L3 amongst connectivity these VLANS.

  Please feel free to expand on your question and provide you with a more precise guidance.

  Arvind