Cannot connect to my the only guest user profile

Similar Questions

• Ad Hoc network. even if the network is active and is connected to the internet my devices cannot connect and then the network shuts down.

  I'm living in a college dorm and only have access to the internet via a hard line to my computer. So I wanted to give my other accessibility of consumer electronics set up an Ad-Hoc network and share the internet connection. When I originally set up the network it works fine, but after the devices go to sleep or I leave the room it stops working. I had problems to keep the internet connection to share continually, which I fixed it. I then had a DHCP problem with the hard line that has been resolved through troubleshooting function. Now, even if the network is active and is connected to the internet my devices cannot connect and then the network shuts down.

  Is there a way to create an Ad Hoc network that works similar to a wireless router, so when my computer is turned, it works automatically? If so, how can I make this happen without these problems?

  Hello

  I suggest to activate temporarily the antivirus as well as windows firewall and check if it helps.

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows7/turn-Windows-Firewall-on-or-off

  For reference:

  Set up a computer-to-computer (ad hoc) network

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-computer-to-computer-ad-hoc-network

  Note: The notes section through the link above.

• "Unable to connect to the computer error' user profile failed to connect.

  Original title: reset windows password after being locked up and he treated the new password, but I'm still locked. I don't have a password reset disk. What should I do now?

  Tour computer off standby. And when I turned it back the next morning that my password would not work. Figured out how to change the password but still getting the same message and still locked. He did deal with the new password, but just do not let me in. I don't have a password reset disk. What should I do now? Any help is greatly appreciated. I have to deal with my computer and must be able to use it as soon as possible. Thank you

  Also says "Service user profile service does not logon.

  You suffer from the dreaded problem 'user profile '. I don't have a good solution, but if you type the entire error message into a Google search box, you will get countless successes with at least some of them containing good advice.

  No one gets a Windows repair CD when buying a PC. You need to burn it yourself via the control panel / backup and restore. It only takes three minutes and having one is absolutely essential for those who wish to make their own PC maintenance.
  Talking about the essential things: a fully tested alternative admin account is one of them. Without one, you can get in diabolical trouble (the same as when not having is not a spare House key where to break a window is a radical and totally useless but effective solution).
  It might be possible to solve your current problem as follows:
  1. keep tapping F8 during the first phase of startup.

  2. select Repair from the menu.

  3. Select an administrator account, and then enter its password.

  4. When you are prompted, select System Restore.

  5. set Windows to a point well before this problem occurred. This will outline also all passwords to their old values.

• When I connect XP it creates a new user profile for me every time. All my documents are gone?

  When I connect XP it creates a new user profile for me every time. All my documents are gone? When I look at it is a new profile is created each time with 000 ext 001 or 002. I tried the restore. I get the error. any suggestions?

  Hello

  · What is the error message when you try to restore?

  · You receive an error message or error code when you start the computer?

  · Do you remember all the recent changes on the computer before the show?

  · What is the number and the model of the computer?

  See the link below and try the steps in the same and check if it helps: problems with Windows XP if your profile is damaged: http://support.microsoft.com/kb/326688

• Get the Error Message: "user profile service service has no logon. Unable to load the user profile"after you remove the Windows Vista administrator account

  Original title: deleted Vista ultima. admin identity and admin authorization password for standard users will not work.

  I inadvertently deleted the admin. identity, I think in Vista Ultima. The photo shows still on the identities, but when I try to open the identity I get the following message, "user profile service service has no logon. User profile cannot be loaded. The admin. password does not work in any of the other identities now, so I can't do updates to most of my programs, such as windows. I can't open the control panel to add and change of identity.

  Hi JBRA47,

  You can consult the following Microsoft KB article and check if it helps to solve the problem:

  Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.

  http://support.Microsoft.com/kb/947215

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot connect to laptop as a primary user only as a guest

  Hello

  I can't log on to my laptop as the main user. Can I open a session as a guest, but not as the main user. Whenever I try to open a session, we read that it cannot download profile. What should I do?

  Looks like you have a corrupt user profile.

  Corrupt user profile:

  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

• Cannot connect to the system Windows - user profile service failed to connect

  I can't connect my laptop for the 1st time

  I get an e-mail from the user profile failed to connect

  User profile cannot be loaded

  Ideas please

  If you have a Toshiba SSD in your laptop there is a problem in windows 7, making it impossible to connect to the system when the storage TOSHIBA utilities are installed. In this case, you will need to find a way to get the system and uninstalling.

• All records showing the attribute read-only - cannot be changed via a Properties dialog box OR the command "attrib" user profile AND is not corrupted

  I use Win 7 64 and recently all my files have begun to show read-only. Other responses on this forum, which suggests to change the read-only via the Properties dialog box, attrib command did not work. In addition, I created a new administrator account as suggested by another answer, but the problem persists on both accounts.

  Several programs will not work now that they can not write files in folders.

  What can I do to fix this?

  Hello

  See the following article for a description of this problem.

  326549 You cannot view or change the read-only or the attributes of system files in Windows Server 2003, Windows XP, Windows Vista or Windows 7

  I hope this helps.

  Thank you for using Windows 7

  Ronnie Vernon MVP

• Cannot access my safe after the migration of user profile

  Hello everyone, welcome to Australia

  I have a user who migrated their user profile from windows to the field of our profile by using the small business server 2003 to connect Computer Wizard. This wizard have not migrated users or My content Safe fingerprints.
  After connection to the old account and attempts to access my safe with password backup, user could not open it.

  Is it possible for the user to access the content in the folder of the safe MYy that these documents are very important. (Take the user to back up only not ;)))

  Hmmm maybe it's not possible to access the MySafe because the laptop is a part of the domain of s.
  I guess that the laptop was not included in the field when the user has used and saved the files in my safe.
  So maybe you could try to reverse the settings and then you might try to enter the folder MySafe.

• Cannot connect pc to the xbox with the befsr41 or upgrade firmware

  Hi, I bought a used befsr41 v.2 router and it worked perfectly, could connect my pc to the xbox and watch the videos/photos/music. A few months later router exploded and so I bought a new v.4 befsr41. Now my xbox says there is no connected computer. The internet connection works on pc and xbox just cannot get them to connect... I tried the upgrade to firmware versions available, but the First firmware that was v 1.04.09 and he says "attention!" upgrade file error model. "Then the second version it only gave me the instructions on how, but not the .bin file. My ISP is Comcast btw. Thanks for any help

  Hi, I found the solution by doing research beyond the discussions, I tried this last time, I bought the router v4 and have not found a so ididnt think that there is one, thanks!

• WCS - Lobby Ambassador users don't see the other guest users

  Hi, we currently have the problem with WCS 5.2 that a user from the group "Lobby Ambassador" can be seen guest users that have been created by another user in this group. The user can only see his own guests created users. All are in the same virtual domain which is the root domain.

  I think that this behavior was not that way in previous versions, here all guest users were visible to all users of the Ambassador Hall.

  I couldn't find any hint in the documentation about it.

  Is it simply a change in behaviour (works as expected) or is it possibly a bug?

  It comes to the operations set out in point 5.2. The function was added by the requests of numerous customers. In 6.0, there will be an admin button to allow all the ambassadors Hall to see all users comments.

• Cannot cannot run .exe file, but only one user.

  I have 4 users put in place in Windows XP Media. Only one user has the problem that windows does not let him run the .exe files. get error asking what program I want to use to open this type of file. 3 other users do not have a problem. How do I fix this one

  Hello

  1. don't you make changes on the computer before the show?
  2. What is the exact error message?

  Method 1:
  Run the fix it and check.
  Diagnose and repair Windows files and folders problems automatically
  http://support.Microsoft.com/mats/windows_file_and_folder_diag/en-us

  Method 2:
  You can try the steps in the link and check if it helps:
  How to change or choose the program that starts when you double-click a file in Windows XP

  http://support.Microsoft.com/kb/307859

  Method 3:
  If the steps above fail then you can try the steps in knowledge base article and check.
  When you run an .exe on a Windows XP, Windows Vista or Windows 7 computer file, the file can start another program
  http://support.Microsoft.com/kb/950505#appliesTo

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry in Windows:
  http://support.Microsoft.com/kb/322756

• Loopback adapter cannot connect past "absorbing the network address.

  well, then I'll put up my loopback adapter (windows xp btw) and iI marketing my loopback adapter, it is like 'Local area connection 64' and it cannot go beyond "absorbing the network address"... and when I click on fix it just expires itsself. And so I am unable to use it...

  Help?

  Right-click on the adapter, and then click Properties.  On the property page click on (highlighted) Protocol Internet (TCP/IP) and then click the properties button and give an IP address to the card.

  John

• I get the error message "user profile service service has no logon. User profile cannot be loaded. No response on this blog has not been useful.

  I use Windows Vista. There is an account called, set up, but he is not an administrator account and I can't change the administrator. I don't have a recovery cd. There is no "HKEY_LOCAL_MACHINE/SOFTWARE/Microsoft / / Windows NT/CurrentVersion/ProfileList. It happened when I used a flash drive and my computer froze and delete my profile. In addition, my computer can not load in safe mode. Any suggestion would be great.

  You have another admin account , you can connect?
  If so, please do and do a system restore, if no help, run the Microsoft Support tutorial below.

  If you don't have another admin account, go into safe mode.
  Here's how to get safe mode:
  Shut down your computer > turn it back on and immediately and repeatedly press F8 key until you see a black and white screen. The top/down arrow and select Safe Mode with network.

  In the window of logon in safe mode...
  1 can connect to your account administrator in safe mode?
  If so, do a restore system first, if no help, run the Microsoft tutorial support listed below.

  2. If you cannot connect to your own account, you see another
  next to your admin account in the logon screen?
  If you do, that one is the built-in Administrator account. By default, there is no password. Logon to it and again
  do a restore system first, if no help, run the tutorial from Microsoft technical support 
  below.

  If you are able to log on in safe mode, do a system restore. Choose a
  Date of when you were able to log in NORMAL MODE as your restore point.
  How to restore the system:
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  Tutorial from Microsoft support :
  http://support.Microsoft.com/kb/947215
  There are several methods, go through one by one.
  Method 3 has a "fix it for me" application

• HP Envy 4500 cannot connect wireless to the printer

  Recently I bought HP Envy 4500 printer. Connected to my router ok TP-Link3631 and have successfully printed from android phone and portable computer connected wifi but cannot print wireless from the office, running XP Pro, but allows you to print via a USB connection. Office see printer through a router using 192.168. etc and printed the report. Have tried to install the software via disc cd and internet several times, Inc. reinstall, but can not get computer to connect. Have been round and round in circles several times, also used print and scan doctor without success. It seems that the software is not fully installed. Or maybe something wrong with the network. Anyone have any ideas? Thank you

  Hi @atr345,

  I see by your post that one of the computers is not recognizing the printer on the network, but you can print by a USB connection. I can help you with this.

  Type the IP address in the address bar of Internet Explorer to see if the built-in Web page printer server load on this computer.

  Check the computer IPV4 address to see if it matches the first 3 games of the IP address of the printer.

  Go to start, type cmd in the search box, enter, then type ipconfig.
  Check the IPV4 address.
  Now, check the IPV4 address for the printer. (192.168.1.9)
  Do the first 3 sets of numbers match? (if they do not match then the computer is not on the right network)

  Try and ping the printer.

  In the same window, type ping printers (space between ping and IP address) IP address
  What are the results?

  If the available printer built-in Web server, the first 3 sets of numbers of computers had matched the address IPV4 of the printer and you could ping the printer, then try and configure the connection to printer wireless via the USB connection.

  Installation of the software of the printer for a wireless network connection.

  Please go to the first step: preparation for installation, number 4.

  If you need help, let me know.

  Good day!
  Thank you.