Cannot find a wireless network with my HP Pavilion

Similar Questions

• HP B209a cannot find the wireless network

  I'm running into a problem with my B209a find a wireless network.  I'm not well versed in wireless/network please bare with me.   I have an iMac with OS X 10.8.2.  Recently, I upgraded my router to an Airport Extreme.  My Mac can see the printer correctly, however, the printer cannot now see the network.  Airport utility, I see all our appliances listed under wireless clients and an IP address without a name (printer?).  Doesn't look like not to add manually wireless clients is no longer an option.

  The wireless is configured with WPA/WPA2 Personal Security.  The radio is set to 802. 11A / n - 802.11b/g/n (automatic).  Anyone have any ideas on how to solve this problem?  Thank you.

  1. Printer, restore the configuration of the network printer.
  2. Turn on the radio to the printer.
  3. From your Mac, connect to the network printer called hpsetup.
  4. Open Safari and select Bookmarks-> Show all bookmarks.
  5. Select Hello on the left.  Your printer should appear in the main window of Safari.
  6. Double-click the printer.  The printer's internal web page should appear.
  7. The Green Network on the printer web page tab.
  8. Select Wireless (802.11) on the left
  9. Press start the wizard and follow the prompts to connect the printer to the network.

  This should get back you on your feet.

• Moved from Office Windows 7 from one room to the other and now it cannot find the wireless network

  Hello world

  I have a HP Pavilion running Windows 7.

  He was hooked through the ethernet in a single room.

  I moved it to another room where there was no inflexible access, so I relied on the use of our wireless network.

  Now, the computer will not even find the wireless network.  When I have the help, it says "no available connection."

  In the center of the network, selecting wireless has a red X to the left of the green signal bars.

  At first, I wondered if maybe the computer was in a "dead point" in our House, but I've put a laptop beside him and he found the thin wireless network.

  Any help?

  Update: I tried system restore and tried to stop/resume knowledge network locations, but to no avail.

  Here is the info on my card wireless directly from HP site:

  Original driver for the solutions of Dualband network Atheros 802.11 Wireless Module a/b/g/n.

  I found what I think, it's their website, (http://www.atheros.cz/atheros-wireless-drivers.php), but surprise... they only model # s, my info does not.  Ugh.

• HP LaserJet Pro CM1415fnw color multifunction printer - cannot FIND the WIRELESS NETWORKS

  PRINTER: HP LaserJet Pro CM1415fnw color multifunction printer

  OS: Windows 7

  OWNER: More than 2 years without any problem

  LOCATION/SET-UP: To my personal residence. All-in-one router through the cable company.

  QUESTION: Suddenly, printer cannot find wireless networks. Nothing has changed recently in my service provider or equipment. I know that the router and the internet is not the problem because our 2 smart phones and three laptops still not connect. I triend manually configure the network using the SSID and key phrases, but still nothing.

  Help!

  I would like to perform a hard reset by removing the power of the whole machienethrough the power cord for 30 seconds. Depending on whether I have would reconnect the printer to the wireless network and set a static IP address.

  -Spencer

• Vista Ultimate cannot find available wireless networks

  Fresh install of Windows Vista Ultimate on my desktop with the Linksys Wireless card can't find any available wireless network. My laptop in the same room (also Vista) detects and connects without any problems. I tried to reset the router, manually force the connection and everything else I can think. Help!

  Hello

  Remove ALL power and reinsert the card, in fact remove and replace, do not just tight.

  Search updated with LinkSys drivers and they have excellent Support and Forums.

  LinkSys - Support - Online Chat drivers
  http://homesupport.Cisco.com/en-us/Wireless/Linksys

  LinkSys - Forums
  http://homecommunity.Cisco.com/community/?category.ID=Linksys

  I hope this helps.
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• 5525 printer cannot find the wireless network

  Help

  I'm not good with technical stuff and need help with this problem.  Printer works well before going on holiday - power off, including the CISCO router when we went away--returned and turned on any return, printer will not connect to the router again.

  Have reinstalled router without result.  All other computers, phones, etc. to connect to the router fine.

  Wireless network test that the MAC address filtering is enabled, they suggest however have checked this and it's not.

  Wireless configuration wizard can find the network but it just seems impossible to connect to him.

  Please assume the lowest level of technical understanding when you reply!

  Thank you

  Hi K27,.

  I see that you are having some problems getting your Photosmart 5525 reconnected to your network after just unplugging a bit. I understand that you have your information wirelessly, but I don't want to set a link here which will take you to our HP print and doctor Scan, which can help you check some things on the wireless network.

  Since you already feed the router to bike, I would recommend restoring the default values of network on the front panel of the printer. You'll want to have your printer on the home screen (should say Photo, Apps and copy). On this screen you want to touch the key/tool icon in the upper right corner, then you want to click on wireless and made scroll down looking for default network. Once you click on that it will ask if you are sure and you want to say Yes. Once that is done, I would recommend the router/printer power cycling tips that were previously provided and then run the wireless configuration that you've been already and it should be able to connect at this time.

  That should hopefully fix it for you, so let me know what happens and I wish you a nice day!

• Cannot find a wireless network icon

  Original title: Wifi problem! Help, please!

  So I have a Samsung laptop and my Wifi icon is gone and replaced with a desktop screen and a right to cable next to him. I access the settings and I am trying to network ind but its always tells me to plug an ethernet cable? It worked fine with wifi and all 3 days ago, but since this icon and I could not find a way back to my wifi! Someone please help it has been for a week now.

  Hi Harry,.

  1. Do you use wired and wireless networks at the same time?
  2. Have you tried restarting the computer?
  3. Have you checked Device Manager to see if your card is still listed and
     the drivers are installed and functioning normally?

  Try to update the drivers, or remove the adapter and reinstall.

  Download and install the drivers

  http://Windows.Microsoft.com/en-us/Windows-8/all-drivers

  Also see this article: why Windows is not find my Bluetooth or other wireless device?

  I hope this helps.

• Satellite A300 1QE - Windows can't find any wireless network

  Hello

  Please help me with a problem of annoing with radio.

  The story is like this:-J' I bought a laptop with Vista preinstaled... I used only once the wireless and worked very well... after a while I have reinstaled Vista, vista ultimate editing... I used 2 days the wireless and then suddenly found no more... wireless network I have reinstaled vista 2 weeks ago, and now I bought a wireless router and set a network... same problem : "Windows cannot find any wireless network"... with a laptop dell, I found 2 networks (one I created and the other a neighbor with very good signal).

  Collaborative I've tried:

  1 http://aps2.toshiba-tro.de/kb0/TSB9602NC0000R01.htm - in the directory toshiba\wlan there are 3 directories: intel, atheros and realtek... following the steps, the only factor that installs is intel one... If I try to navigate to the folder Realtek can't find anything compatible... (the network lan card is realtek, so I guess that the Wlan should be the same... as also indicated in the url)

  "I have the latest drivers from the toshiba Web site
  "the wireless is a turn on"

  2. I thought that might be a vista problems, so I instaled all the vista updates available... still no work

  The next sollution I try is updating the bios, but I have no whink it is useful.

  So please help me with a sollution for my WiFi problem!

  Thank you

  Hi creativu22,

  First, you must identify the type of wireless network card before you begin to install all the drivers available. Therefore, you can also search with vendor and device ID.
  Check this box!

  If you have installed the driver successfully and your wireless network adapter is listed in the Device Manager, you must check the TCP/IP settings. Maybe you need to use static IP addresses, but it depends on your router.

  Try turning off also in Power Options Windows WLAN energy saving features!

• Inspiron unable to find the wireless network, wifi catcher is on

  I have a Dell Inspiron 1500, recently was unable to connect to the wireless network. Cannot find same wireless networks when I search. A WiFi catcher is enabled.

  Hello

  I suggest you to follow the steps in this link and check if it fhelps:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Also check out this link:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

  It will be useful.

• WINDOWS CANNOT FIND ANY ADDITIONAL NETWORK (DIAL-UP AND VPN) OTHER THAN THE WIRELESS NETWORK

  ehmm I just installed nokia 6600 pc suite on my computer so I can access the internet on my computer through the usb cable. Installation and drivers have been installed correctly. I can access the internet on the handset but when trying to connect to the internet via USB with the computer "I get a message that windows cannot find any additional network." Its really disturbing that I can do to fix this. Can someone help me please.

  Even if a USB device, it does not create a new network connection for you.  I fear also that you use a regular USB cable - those connections often require a crossover cable (but more on that later and I guess it should work it is how it is advertised).  Go to start / Control Panel / Network and sharing center / set up a connection or network / and choose the first option (you can also check the main page to see if the connection is listed but I doubt it).  Choose to set up a new connection and follow the instructions - ensuring that you enter the correct settings when it is required.  You should perhaps install device drivers, firmware and or software for the device to work properly - read the installation mode (and call technical assistance from Nokia to help you put in place - they know more about what we do and should be happy to guide you through the process and even to set the settings on your computer until you log - that's what I would do in your before circumstane even of) ask for help here).

  To start / Control Panel / Device Manager and check all the new drivers (double clck on them) to confirm that they say that they do not work properly.  Go to start / Control Panel / Add Haedware and have the system check new hardware devices - if it finds, install them (it is perhaps what is missing in this process).

  I hope this helps.  If nothiing suggested I bring, don't hesitate not to contact Nokia for assistance - I'm sure they'll have you place and operate at any time.  Keep me in the loop.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows cannot find any additional network / an unexpected error has occurred

  I got this new PC Windows Vista Home Edition x 64 SP2 and I need to connect it to the network wireless in my house because that the router Netgear DG834GT wireless broadband is not very conveniently placed for wired connectivity. I have a Netgear WG111T USB wireless adapter which works fine on my other PC / laptop (XP & Vista, both 32-bit), but I can't make it work on my Vista x 64 PC.

  I have installed the version of the driver 2.1.0.26 x 64-compatible for the WG111T and the device works correctly, according to Device Manager.

  When I try to 'connect', I get 'Windows cannot find any additional network . " While the other PC at home can pick up 3 wireless networks.

  Go until the network & sharing Center, then manage the networks without wire, then Add, then manually create a network profile, I get "unexpected error ."

  I spoke to Netgear who insist the player WG111T is compatible with the x 64 visits.

  I talked to my PC provider who suggested to try the adapter on another PC Vista x 64 to see if it works there. Problem is, I don't know anyone else with a Vista x 64 PC.

  I would be extremely grateful if someone can help me before on this one. Thanks in advance for all advice.

  See you soon,.

  Arty-W

  It seems that the problem was caused by ZoneAlarm Internet Security Suite hinder and prevent the correct installation of the Netgear wireless driver. My problem has been cured by following the advice of daouda wire - see http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/58716eca-80cb-4555-a1f4-bd4e5350aeb4

• LaserJet 200 color M251MW: driver software cannot find printer wireless HP Laserjet 200

  I have printer HP Laserjet above 200. It's worked great for me and another person in my office. However, I've changed computers, and no matter what I do, the driver cannot find the printer. The other person in my office can always print very well, and my old computer can print always very well. I have disabled the firewall, turn off network security essentials (it is not yet installed antivirus software), provided the IP address, network address, the name of the device, let the software to set up my connection Wireless for HP Direct print. I restarted the printer, restarted my computer, restarted the router wireless, connected the printer directly to my computer via the supplied USB cable. It does not find the printer. I can ping to the IP address of the printer and get a quick response. I can print to other printers on network in the building, I just can't connect using HP. !

  None of that helped him. What is strange, is that when I plug the USB in, it feels immediately there is a printer is connected. It starts to install the software, asking me to acknowledge T & C before you get a read error "unable to create the folder to extract webpack". I am an administrator on this computer and the network, and he gave permission to run. However when I use the driver from HP, it cannot find the printer, even with connected USB? The HP print and scan doctor finds the printer immediately, on the network, but then try to install the same software that does not find the printer.

  I have finally however solve the problem, the key was to not install all other HP services, other than those needed to print. Deselection of all the software options (components 6-8) allowed him to immediately find the printer maybe 2 seconds, select these elements and not found the printer. HP needs to offer a thin driver that actually works, rather than trying to sell ink, just something that allows you to print would be useful. It's frustrating to spend 6 to 8 hours trying to configure a printer when the problem appears to be with the driver.

  For others with this problem, run the HP print scan doctor, download the driver again through this software, deselect all option provided with the driver software and continue.

• C4780 cannot find the wireless router

  I have a new iMac and old Toshiba that is running Windows XP and you use a Netgear wireless router.  When I got to the printer, it worked fine on the wireless network.  Bought a new router that I couldn't work with the Mac and the PC so I returned to my original router.  Now, the printer does not work as a wireless printer.  Summaries of diagnosis indicates that the printer cannot find the wireless router and fails under "Network Name (SSID) Found."  On the Network Setup page, my network is listed as a network discovered by the printer.  I guess there is a simple solution and hope to find the answers here.

  Thank you very much!

  Some printers C4780 left the factory with a default misconfiguration.  This could be the reason why you can not see the hpsetup network.  Here is an updated set of instructions for manually adding the C4780 to a Mac:

  Part 1 - Get the printer in Ad-Hoc Mode Wireless

  (1) turn on the printer.

  (2) display the printer has six keys; three on the left (top-left, middle left, below on the left) and three on the right (top-right, centre-right, bottom-right).  Press and release the following touch buttons in order:

  top left,

  bottom-left,

  top left,

  top left.

  (3) you should see the internal menu of printers.  Press the right button down to select 'Service Menu'.  Press OK (lower-left).

  4) press the lower button right until you see "Reset Menu".  Press OK (lower-left).

  5) press the lower button right until you see "half full".  Press OK (lower-left).

  (6) after a few seconds, the printer turns off.  Press the power button to turn on the printer.  It is now reset with the correct default network settings.

  (7) turn on the radio:

  Press the Scan button to get the wireless settings

  Select wireless Menu

  Select wireless settings

  Select Enable Wireless to turn on the radio.

  Part 2 - run the Wireless Setup Wizard

  The printer has now created an ad - hoc network called hpsetup.  To connect to this network on your Mac.

  Check the connection to the printer by opening the printer's internal web page.  You can do this by opening Safari, select bookmarks then ShowAll bookmarks.  On the left pane of Safari, select Hello and on the right, you should see your printer listed.  Double-click your printer and Safari should display the printer's internal web page.

  The printer Web page, select the network tab, and then select Wireless (802.11).  Now press Start the wizard to launch the wireless configuration wizard.

  When the wizard is finished, your computer unplug the printer's ad - hoc network as the printer reconfigures itself to connect to your network home.

  Reconnect your computer to your home network.  Verify that you can connect to the printer at the opening of its internal web page again once we were doing before.

  Finally, install the printer SW.  Since you have Snow Leopard, you don't need the CD that came with the printer.  Instead, open the Print & Fax under System Preferences applet and press the [+] button.  Highlight your printer and click Add.

• Satellite A300 - cannot locate any wireless network

  Hi all

  I just bougth today a Satellite A300, everything works fine except the wireless access. Ethernet access works very well, and the problem is not with my wireless device since it works with my old laptop.

  It cannot locate any wireless network. It does not appear to be activated WLAN and I don't know how to enable it in the BIOS.

  The swicht wireles on the front of the laptop is turned ON, but not the function Fn + F8 appearing at all.

  Can anyone help please?

  What you mean with this WLAN is in the BIOS not enabled? Normally, you can change all BIOS options then try to activate it.
  Also make sure that the WLAN switch is on and active with FN + F8.

  Visit the Toshiba for a driver and the update to the BIOS:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

• CNV cannot find variable on network

  I start my exploration of the network (NVC) with examples of variables.  Excellent examples.

  Using the project of polling stations, I have the program running on a PC writer.  On another PC, I have the player running program.  I modified slightly so that the path of the network would be selectable by using the sample browser project.

  The drive cannot find the variable network writer.  The browser popup (where the player is running) is the PC that hosts the writer program.  So it's good, in the sense that it checks the two computers are on the same network and subnet.

  But in the browser, the tree is not all associated network variables.  This seems to be a simple problem, but I can't find.

  Also, if I run the application Reader on the same computer that hosts the application to the writer, this popup browser detects the attached network variable.  So, I know that on the same PC, writer and reader work.  Just not on my network (which is kinda the whole point!)

  Here you will find two documents that I have found useful when configuring the network variable scenario:

  Software configuration and firewalls hardware to support National Instruments products

  LabVIEW static Variables through Windows 7 firewall