CNV cannot find variable on network

Similar Questions

• Windows cannot find any additional network?

  I am currently using my laptop that can connect to my home network but my PC can't. My PC can't find no additional network. It says it is connected to the network called 'Network', but I can't use my internetor all programs using the internet. It says "windows cannot find any additional network." I clicked on "Diagnose why windows cannot find any additional network", it told me to update my drivers and my drivers he's was updated. Can someone help me?

  Hello

  You can check the link below and try the advice given and check if that helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/Windows-cannot-find-any-additional-networks-an/ca9f086b-42A5-46E5-b894-92c009f8eba8

  Hope that information was useful

• Windows cannot find any additional network / an unexpected error has occurred

  I got this new PC Windows Vista Home Edition x 64 SP2 and I need to connect it to the network wireless in my house because that the router Netgear DG834GT wireless broadband is not very conveniently placed for wired connectivity. I have a Netgear WG111T USB wireless adapter which works fine on my other PC / laptop (XP & Vista, both 32-bit), but I can't make it work on my Vista x 64 PC.

  I have installed the version of the driver 2.1.0.26 x 64-compatible for the WG111T and the device works correctly, according to Device Manager.

  When I try to 'connect', I get 'Windows cannot find any additional network . " While the other PC at home can pick up 3 wireless networks.

  Go until the network & sharing Center, then manage the networks without wire, then Add, then manually create a network profile, I get "unexpected error ."

  I spoke to Netgear who insist the player WG111T is compatible with the x 64 visits.

  I talked to my PC provider who suggested to try the adapter on another PC Vista x 64 to see if it works there. Problem is, I don't know anyone else with a Vista x 64 PC.

  I would be extremely grateful if someone can help me before on this one. Thanks in advance for all advice.

  See you soon,.

  Arty-W

  It seems that the problem was caused by ZoneAlarm Internet Security Suite hinder and prevent the correct installation of the Netgear wireless driver. My problem has been cured by following the advice of daouda wire - see http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/58716eca-80cb-4555-a1f4-bd4e5350aeb4

• WINDOWS CANNOT FIND ANY ADDITIONAL NETWORK (DIAL-UP AND VPN) OTHER THAN THE WIRELESS NETWORK

  ehmm I just installed nokia 6600 pc suite on my computer so I can access the internet on my computer through the usb cable. Installation and drivers have been installed correctly. I can access the internet on the handset but when trying to connect to the internet via USB with the computer "I get a message that windows cannot find any additional network." Its really disturbing that I can do to fix this. Can someone help me please.

  Even if a USB device, it does not create a new network connection for you.  I fear also that you use a regular USB cable - those connections often require a crossover cable (but more on that later and I guess it should work it is how it is advertised).  Go to start / Control Panel / Network and sharing center / set up a connection or network / and choose the first option (you can also check the main page to see if the connection is listed but I doubt it).  Choose to set up a new connection and follow the instructions - ensuring that you enter the correct settings when it is required.  You should perhaps install device drivers, firmware and or software for the device to work properly - read the installation mode (and call technical assistance from Nokia to help you put in place - they know more about what we do and should be happy to guide you through the process and even to set the settings on your computer until you log - that's what I would do in your before circumstane even of) ask for help here).

  To start / Control Panel / Device Manager and check all the new drivers (double clck on them) to confirm that they say that they do not work properly.  Go to start / Control Panel / Add Haedware and have the system check new hardware devices - if it finds, install them (it is perhaps what is missing in this process).

  I hope this helps.  If nothiing suggested I bring, don't hesitate not to contact Nokia for assistance - I'm sure they'll have you place and operate at any time.  Keep me in the loop.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Cannot find variable

  Hello
  How to resolve these?
  45 results of the object = operationBinding.execute ();
  46 if (! operationBinding.getErrors () .isEmpty ()) {}
  
  Error (45.25): cannot find variable operationBinding
  Error (46,14): cannot find variable operationBinding

  Oh ho...

  no problem with your import declaration.

  thing is: Error (45.25): cannot find variable operationBinding
  Error (46,14): cannot find variable operationBinding.

  variable 'operationBinding' can not identified by the compiler. Why the compiler is not identified. you did not define who

  so I define the operation binding and intializse that.

          BindingContainer bindings = getBindings();
          OperationBinding operationBinding = bindings.getOperationBinding("Here your operation"); //..this is line compiler is expecting. to avoid that.
  45    Object result = operationBinding.execute();
  46    if (!operationBinding.getErrors().isEmpty()) {
  

• X 250 reports for SCCM 2007 boot disk WinPE "cannot find a valid network adapter."

  I built a 250 X with Win7sp1 Enterprise, used Lenovo System Update to update all drivers, driver and creates a new package of drivers of SCCM 2007.

  I added the driver v 12.12.80.1950 Intel I217-LM to the Boot Image, distributed to distruting SCCM points and created a new USB stick to boot using the SCCM Assistant.

  When I boot on the USB drive I get the message "cannot find a network adapter valid."

  I can use the ignition key on a 240 X without any problems.

  I can see the pilot I217-LM in the boot image. When I connect locally on the laptop, I can connect to a share on another PC, so the driver and connecting to the LAN function. It is only during boot on the key of USB startup problem occurs.

  Any help much appreciated.

  Problem solved.

  The boot image, I added the driver to was "not to inject a ConfigMgr driver", I created a new boot image added three drivers NET from the driver package provided by Lenovo SCCM for X 250 and the laptop can now connect to the SCCM server.

• HP LaserJet Pro CM1415fnw color multifunction printer - cannot FIND the WIRELESS NETWORKS

  PRINTER: HP LaserJet Pro CM1415fnw color multifunction printer

  OS: Windows 7

  OWNER: More than 2 years without any problem

  LOCATION/SET-UP: To my personal residence. All-in-one router through the cable company.

  QUESTION: Suddenly, printer cannot find wireless networks. Nothing has changed recently in my service provider or equipment. I know that the router and the internet is not the problem because our 2 smart phones and three laptops still not connect. I triend manually configure the network using the SSID and key phrases, but still nothing.

  Help!

  I would like to perform a hard reset by removing the power of the whole machienethrough the power cord for 30 seconds. Depending on whether I have would reconnect the printer to the wireless network and set a static IP address.

  -Spencer

• HP B209a cannot find the wireless network

  I'm running into a problem with my B209a find a wireless network.  I'm not well versed in wireless/network please bare with me.   I have an iMac with OS X 10.8.2.  Recently, I upgraded my router to an Airport Extreme.  My Mac can see the printer correctly, however, the printer cannot now see the network.  Airport utility, I see all our appliances listed under wireless clients and an IP address without a name (printer?).  Doesn't look like not to add manually wireless clients is no longer an option.

  The wireless is configured with WPA/WPA2 Personal Security.  The radio is set to 802. 11A / n - 802.11b/g/n (automatic).  Anyone have any ideas on how to solve this problem?  Thank you.

  1. Printer, restore the configuration of the network printer.
  2. Turn on the radio to the printer.
  3. From your Mac, connect to the network printer called hpsetup.
  4. Open Safari and select Bookmarks-> Show all bookmarks.
  5. Select Hello on the left.  Your printer should appear in the main window of Safari.
  6. Double-click the printer.  The printer's internal web page should appear.
  7. The Green Network on the printer web page tab.
  8. Select Wireless (802.11) on the left
  9. Press start the wizard and follow the prompts to connect the printer to the network.

  This should get back you on your feet.

• Moved from Office Windows 7 from one room to the other and now it cannot find the wireless network

  Hello world

  I have a HP Pavilion running Windows 7.

  He was hooked through the ethernet in a single room.

  I moved it to another room where there was no inflexible access, so I relied on the use of our wireless network.

  Now, the computer will not even find the wireless network.  When I have the help, it says "no available connection."

  In the center of the network, selecting wireless has a red X to the left of the green signal bars.

  At first, I wondered if maybe the computer was in a "dead point" in our House, but I've put a laptop beside him and he found the thin wireless network.

  Any help?

  Update: I tried system restore and tried to stop/resume knowledge network locations, but to no avail.

  Here is the info on my card wireless directly from HP site:

  Original driver for the solutions of Dualband network Atheros 802.11 Wireless Module a/b/g/n.

  I found what I think, it's their website, (http://www.atheros.cz/atheros-wireless-drivers.php), but surprise... they only model # s, my info does not.  Ugh.

• Windows 7 cannot find the HP network printer to install.

  Original title: windows network printer problem 7 and HP

  I just bought a new computer with windows 7.  I have a HP printer connected hard wire t my verizon router.  My old computer running windows xP can find the printer on the network wireless.  My new computer running windows 7 sitting right next to him does not have the printer to install.  I had HP tech support those who are working on this for many hours and they cannot understand it.  I need help with that.  How to get windows 7 to see the printer.  How can you help me?

  It is rare that there is no option to specify an address

  Now that you know the address of printers, you can successfully ping it?

• Cannot find a wireless network with my HP Pavilion

  I really need help. I had this problem a couple of times, and every time I had to restart my entire computer and reinstall everything before I could connect again. The computer has no connection with a cable problem, but he says he can't find a Wi - Fi connection. I would really avoid the reboot and restore the computer to a fifth time if I could. I don't know the details of the computer, I think it might be a Touch 14z...

  Hi ImpossiblyOswin,

  Here is a document from HP Networking Wireless and Internet troubleshooting support with a number of troubleshooting steps to try to including buildings in the troubleshooter in Windows. This information you provided was what I was looking for. When you mention reinstall in your first post, what are you reinstall?

  Thank you

• Vista Ultimate cannot find available wireless networks

  Fresh install of Windows Vista Ultimate on my desktop with the Linksys Wireless card can't find any available wireless network. My laptop in the same room (also Vista) detects and connects without any problems. I tried to reset the router, manually force the connection and everything else I can think. Help!

  Hello

  Remove ALL power and reinsert the card, in fact remove and replace, do not just tight.

  Search updated with LinkSys drivers and they have excellent Support and Forums.

  LinkSys - Support - Online Chat drivers
  http://homesupport.Cisco.com/en-us/Wireless/Linksys

  LinkSys - Forums
  http://homecommunity.Cisco.com/community/?category.ID=Linksys

  I hope this helps.
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• 5525 printer cannot find the wireless network

  Help

  I'm not good with technical stuff and need help with this problem.  Printer works well before going on holiday - power off, including the CISCO router when we went away--returned and turned on any return, printer will not connect to the router again.

  Have reinstalled router without result.  All other computers, phones, etc. to connect to the router fine.

  Wireless network test that the MAC address filtering is enabled, they suggest however have checked this and it's not.

  Wireless configuration wizard can find the network but it just seems impossible to connect to him.

  Please assume the lowest level of technical understanding when you reply!

  Thank you

  Hi K27,.

  I see that you are having some problems getting your Photosmart 5525 reconnected to your network after just unplugging a bit. I understand that you have your information wirelessly, but I don't want to set a link here which will take you to our HP print and doctor Scan, which can help you check some things on the wireless network.

  Since you already feed the router to bike, I would recommend restoring the default values of network on the front panel of the printer. You'll want to have your printer on the home screen (should say Photo, Apps and copy). On this screen you want to touch the key/tool icon in the upper right corner, then you want to click on wireless and made scroll down looking for default network. Once you click on that it will ask if you are sure and you want to say Yes. Once that is done, I would recommend the router/printer power cycling tips that were previously provided and then run the wireless configuration that you've been already and it should be able to connect at this time.

  That should hopefully fix it for you, so let me know what happens and I wish you a nice day!

• Cannot find a wireless network icon

  Original title: Wifi problem! Help, please!

  So I have a Samsung laptop and my Wifi icon is gone and replaced with a desktop screen and a right to cable next to him. I access the settings and I am trying to network ind but its always tells me to plug an ethernet cable? It worked fine with wifi and all 3 days ago, but since this icon and I could not find a way back to my wifi! Someone please help it has been for a week now.

  Hi Harry,.

  1. Do you use wired and wireless networks at the same time?
  2. Have you tried restarting the computer?
  3. Have you checked Device Manager to see if your card is still listed and
     the drivers are installed and functioning normally?

  Try to update the drivers, or remove the adapter and reinstall.

  Download and install the drivers

  http://Windows.Microsoft.com/en-us/Windows-8/all-drivers

  Also see this article: why Windows is not find my Bluetooth or other wireless device?

  I hope this helps.

• Cannot find a home network - G60-630US

  I see other wireless networks but not my home network. Turned computer walking several times and reinstalled all both network cards.

  Hello @alethea11 ,

  Welcome to the HP Forums!

  I understand that your notebook is not your home network.

  Start later.

  Powercycle the network:
  1. turn off your laptop.
  2. unplug the power to your router.
  3. disconnect the power to your modem.
  4. wait at least 45 seconds.
  5 reconnect the modem and wait for it to come back online.
  6 plug in the router and wait for it to come back online.
  7. turn on your laptop and test your connection.

  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.

  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.

  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.

  If these steps do not resolve the problem, try this document published by Microsoft for network management issues: wired and wireless network problems. You can change the operating system with the drop-down list in the upper right of the document.

  If you have other available networks, you can try to change the channel of your wireless router to eliminate (RFI) radio frequency interference. try to set it to 1 or 11 (default is usually 6). It will take, as far as possible most of the other networks, the dissemination of the wireless signal. To do this, you will need to contact the technical support of the manufacturer of your router. Don't forget that you can also reset the router completely for a new start, which may be a good idea.

  Let me know if it helps!