Cannot get Adprep to run on W2K Server. I am also running Exchange 2000 on this computer.

Similar Questions

• I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  Installed the new hard drive on my Toshiba laptop and when I ran my recovery disk, Windows Vista installed, but when I restarted computer I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  Help, please.

  Hello
   
  
  Your error message, the problem is probably caused by BIOS or DVD settings or bad cabling to SATA hard drive. Please do the following to narrow down because of the problem.
   
  (a) ensure that all laptops the same hardware, the same manufacturer and the same model.
   
  (b) upgrade the BIOS to the latest version; go into the BIOS and enable "Load Fail - Safe Defaults".
  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions
   
  Warning of the BIOS:
  BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
  
  (c) If you connect the SATA drives, please configure the SATA controller in compatible mode in the BIOS.

• Windows 2008 R2 as a guest cannot get the IP address of the server (VMware workstation 7.1.3 on Windows 7) professional

  Hi gurus,

  I installed VMware workstation 7.1.3 on my Windows 7 laptop professional x64bit and I can run my old VM (XP) without any problems in this regard. And I tried to install a new client (Windows 2008 R2 Standard x 64) on this subject, when I put the NETWORK card in the deck, he cannot get the IP address from my DHCP, always show me error "Windows has detected an IP address conflict...". ", I tried the IP static installation for her also, same result.

  I tried to install a new windows Server 2003 as a guest (also defined as a network bridge), it works very well, can get the IP address from my DHCP or can set a static IP address with no problems. Does anyone have a similar experience on this combination? Any solution to this issue?

  Best regards

  BUGBUG

  I recently managed to get bridge network work with a Windows Server 2003 R2 SP2 guest in VMW Workstation 7.1.4.385536 on a host Windows 7 SP1 Ultimate.

  VirtualBox 4.0.4.70112 is installed on the host and disabling the 'VMware Bridge Protocol' in the 'VirtualBox in Ethernet Adapter"on the host was necessary.

  Outpost Firewall Pro 7.1.0.3415.520.1247 is also installed on the host computer and I used some information from the link below to add some necessary firewall rules.

  http://www.agnitum.com/support/KB/article.php?id=1000061

• Cannot get the spooler running to connect to the hp C310a printer

  Can't get my hp photosmartprem printer. to print, cannot connect. When I try to connect to the printer, it says that the spooler is not running. Can I connect in safe mode. I have a disc supplied with the printer C310a but maybe I'am something wrong. Could someone please help me to start printing. I would really appreciate it. Thank you * address email is removed from the privacy *.

  Hello

  Check chan seen message here - one of the highest.

  fixed spooler subsystem app stopped working
  http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e

  ===================================

  If the above didn't help:

  Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
  the latest driver).

  Check Mr. Fixits here and if you use the other methods go back and try again later.

  Problems of print and error - a Mr Fixit of printing
  http://support.Microsoft.com/GP/printing_problems

  Solve printer problems - a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx

  ------------------------------------------------------
  Logon as administrator

  Start - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN

  You can copy and paste each line except those brackets and press ENTER after each.

  net stop Spooler

  (echo suppression of all print jobs)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  del/q %SystemRoot%\system32\spool\printers\*.*

  net start Spooler

  (sound Done!)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  Another way
  http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/

  Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
  http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspx

  If you use Control Panel - Classic - printers

  Try after unplugging your printer if necessary.
  -------------------------------------------------------------

  Also check the spooler print and its dependencies and addictions Service.

  Print Spooler service
  http://www.blackviper.com/WinVista/services/Print_Spooler.htm

  How difficulty Windows Vista print spooler starts do not
  http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html

  ------------------------------------------------------------

  Check this thread if necessary - to stop and erase the spooler

  http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a15779d6-ac0d-42FD-9Ac2-a1da241ea19f/

  and here
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/58b54fa9-cf6f-40F7-90b2-8093c6777493

  ------------------------------------------------------
  Clean the General corruption and repair or replace the damaged/missing files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  CheckDisk (chkdsk) runs at startup.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------

  Also check with HP support and forums.

  HP support
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  I hope this helps.

• Cannot get the list of Ports on server using Powertool

  I try to get the list of Server Ports that have been activated on the FI-s using Powertool

  I use the below command and I don't get nada

  Get-UcsFabricServerCloud-Id "A" | Get-UcsServerPort - AdminState "enabled."

  Have tried without the additional options with no luck

  Get-UcsFabricServerCloud-Id "A" | Get-UcsServerPort

  The following command gives me a good performance

  Get-UcsFabricServerCloud-Id 'A '.

  On a whim, I also tried the below with no luck

  Get-UcsFiLanCloud-Id "A" | Get-UcsUplinkPort - IfRole 'server '.

  Any help appreciated.

  As for my other answer, you'd better start searching for the network element.  In this case, I'm looking for ports that are of the type "ether" and have an Interface to 'server '.

  PS C:\ucs > Get-UcsNetworkElement | Get-UcsFiModule-Id 1 | Get-UcsPortGroup-ether of Transport | Get-UcsFabricPort - IfRole Server | Select dn, peerdn, ifrole, operspeed | Format-Table

  Dn                                                PeerDn                                            IfRole                                            OperSpeed

  --                                                ------                                            ------                                            ---------

  sys/switch-A/slot-1/switch-ether/port-1 sys/chassis-1 /-1/tissu/port-1 10 Gbps server location

  sys/switch-A/slot-1/switch-ether/port-2 sys/chassis-1/slot-1/fabric/port-2 Server 10 Gbps

  sys/switch-A/slot-1/switch-ether/port-3 sys/chassis-1/slot-1/fabric/port-3 Server 10 Gbps

  sys/switch-A/slot-1/switch-ether/port-4 sys/chassis-1/slot-1/fabric/port-4 Server 10 Gbps

  sys/switch-B/slot-1/switch-ether/port-1 sys/chassis-1 /-2/tissu/port-1 10 Gbps server location

  sys/switch-B/slot-1/switch-ether/port-2 sys/chassis-1/slot-2/fabric/port-2 Server 10 Gbps

  sys/switch-B/slot-1/switch-ether/port-3 sys/chassis-1/slot-2/fabric/port-3 Server 10 Gbps

  sys/switch-B/slot-1/switch-ether/port-4 sys/chassis-1/slot-2/fabric/port-4 Server 10 Gbps

  Hope that helps.  Let me know if you have any other questions.

  Thank you
  Eric

• I have windows 7 64 bit and cannot get my search running index.

  I tried option evey on every thread here, and search for google, including the verification of registry keys, checking and unchecking options based on windows, etc, etc, etc...  When I click I have no tab file types that everyone refers to advanced options, also cannot use the change because it is grayed out, please help?  Have also tried to create the new user account and get the same results.  I'm at my wits end!

  Hi patricelaurence,

  Thanks for posting the question on Microsoft Community Forums.
  Description of the question, we understand that this index does not.
  We will try to help you solve the problem.
   
  Here are some steps that you can follow:
   
  Method 1:
  Open the troubleshooter for search and indexing
  See the link below:
  http://Windows.Microsoft.com/en-us/Windows7/open-the-search-and-indexing-Troubleshooter
   
  Method 2:
  We recommend that you perform the clean boot.
  Put your boot system helps determine if third-party applications or startup items are causing the problem.
  Consult the following link:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: See "How to reset the computer to start as usual after a clean boot troubleshooting"
  under more information to prepare the computer to start as usual after a repair.
   
  Method 3:
  Try disabling the security on your computer program and check whether the problem is resolved.
  See the link below for assistance:
  http://Windows.Microsoft.com/en-in/Windows7/disable-antivirus-software
  Note: After checking the question you must reactivate the security on your computer program.
  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.
   
  Hope this solves the problem. If the problem persists, you can write back to us and we will be happy to help you further.

• Cannot get the clock running.

  I can't get this working analog clock using time returned by the php.

  Server = new LoadVars();

  server.onData = function (src) {}

  counter.onEnterFrame = count down;

  counter._visible = true;

  this.time = Number (src);

  };

  server.load ("http://www.webme.com/time.php" "");

  Counter._visible = false;

  countdown = function() {}

  this.msecs = server.time;

  var s = Math.floor (this.msecs);

  var minutes = Math.floor(this.secs/60);

  varhour = Math.floor(this.mins/60);

  root._Counter.hours_mc._rotation = (hours * 30) + (minutes/2);

  root._Counter.minutes_mc._rotation = 6 * mn;

  root._Counter.seconds_mc._rotation = 6 * dry;

  }

  PHP

  $tz = new DateTimeZone('Africa/Conakry');

  $date = new DateTime ('now', $tz);

  echo "time =". strtotime ($date-> format ('Y-m-d ├a'));

  Thank you and happy new year!

  you see the time on the server?  If so, decrement, server.time in countdown().

• Cannot get rid of the Logitech Media Server app

  Hi, I installed Logitech Media Server on my rn104, but I don't need. I tried to remove it from the web INTERFACE, but it is still visible to the computers on my network and always accessible on port 9000. When I reboot the NAS, he reappears in pre-installed applications. Any ideas how I can kill this annoying thing?

  I sent you a PM.

• Cannot get XP to run in 16:9 format. How can I do?

  How to set my XP to the former display on my new monitor 19:9 ratio format.

  Hello

  Right-click on an empty part of your desktop, and then click Properties. Click on the settings tab drag the slider all the way to the right. This should give the native resolution of your monitor. If not you may need to get the latest drivers for the graphics card.

  If that makes things too small, you can try to slide to the left to get a lower resolution but I suggest using only a resolution that keeps the 16:9 ratio.

  Tricky

• Satellite U300 - cannot get sound card running Windows XP Home edition

  Hi all

  I installed Windows XP Home edition on my U300 after playing with nlite nd the sata raid drivers.
  I installed all think them, but my card doesn't work his and my webcam also. I m now 3 days on it and t can find a solution. Please if someone else have a successful installation of Windows XP Home on the U300-115, please give some advice.

  BTW, the installation order mentioned on the download driver of the page s + ++ s... Toshiba has a driver install package for us is better.

  THX
  John

  Hello

  about the noise I recommend going to www.realtek.com and download the driver from there, which would be much better then the driver on the toshiba site. :)

  In regards to your webcam I Don t know how to help you because I watched the driver download page and I found something didn t. Maybe you should try the camera of another model software since the cameras are the same. I read on some forums (not here) that users tried with their machines and it worked for them.

  It s worthy to give it a try.
  Welcome them

• When I close Firefox my computer says it is still ongoing and I have to restart my computer to get Firefox to run... This is a first for me.

  Every time I close Firefox and try restarting my computer leaves a message that I have Firefox running and that it does not and must be closed. The problem is that it is not a Firefox always running, therefore, it is impossible to close and therefore impossible to open it. I used all forms of Firefox and this is the first time that this has happened. Please, please don't force me to use Chrome or iExplorer!

  Use "Firefox > output" (Windows: Firefox/file > quit;) Mac: Firefox > quit Firefox. Linux: Firefox/file > exit) to close Firefox if you are currently doing by clicking on the X close in the title bar of Firefox.

  You can check if it is useful when you can start Firefox in Safe Mode by holding down the shift/Options key.

  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• I have a laptop running on Windows XP. the machine says that it is VISTA-ready. Can I buy and run Windows 7 on this computer?

  Toshiba Satellite P105 with intel CentrinoDuo

  Windows WP Professtional

  Version 5.1.2600 Service Pack 3 Build 2600

  Hello

  Go to the Toshiba website and check if Windows 7 drivers are available for your make and model laptop.

  If this is not available, Windows 7 will not properly work for you.

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  And choose the right model P105.

  Run the "Windows 7 Upgrade Advisor.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  Check if your specifications are compatible for Windows 7:

  "Windows 7 system requirements"

  http://Windows.Microsoft.com/en-us/Windows7/products/system-requirements

  "Windows 7 Compatibility Center" for software and hardware:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  And the Microsoft Store where you can get an idea of the price of Windows 7:

  http://www.microsoftstore.com/store/msstore/en_US/list/CategoryID.50726100

  See you soon.

• Get the blue screen error saying windows has shut down to prevent damage to this computer

  My sons computer is BLUE with a message saying that windows was arrested for not to damage your computer. And it is stuck on that screen. Do you know why windows shuts down his computer?

  * original title - my son computer is blue and a message indicating that windows has stopped to avoid damaging his computer. And he is not able to do anything. Do you know what it is? *

  Hello

  1. what operating system is installed on his computer?
  2 did you the hardware changes to his computer before the question?

  Perform the steps in the article and see if the problem is resolved or not.
   

  Resolve stop (blue screen) error in Windows 7

  Also check the event viewer for error logs

  Open event viewer

  What are the information contained in the logs of the event (Event Viewer)?

• Newly installed hard drive, cannot get the reinstallation of Windows 7 to the end

  Hi all. My factory-issued Seagate 1 TB hard drive of origin provided with my PC Pavilion Elite HPE-240f failed a few months ago and I finally had time to fixation (rock a Pavilion dm4 laptop in the meantime, I'm not in a huge rush). I replaced it tonight with a Western Digital Blue 1 TB hard drive, which I know is Advanced Format.

  I love HP platform minor changes in the the Windows 7 OS, I went ahead and tried to reinstall the OS of my recovery disks that I made when I got this PC. I checked the BIOS settings and the new hard drive WD IS recognized, the size is correct, etc. It has been configured in RAID with the SATA controller, and I tried to put out when the installation of the operating system initially lacked AHCI. It seems to be stuck in some kind of loop in the final configuration step, and I get out of the dialog box "Installation of Windows set up Windows to run on a hardware on this computer" could not. Hit Okay sends in reboot and after that I get a "Windows is unable to complete the installation. To install Windows on this computer, restart the installation"notice.

  It makes me batty, and I really want my back office. This is a great machine, and as much as I love my laptop, it can't handle heavy programs like Photoshop or my multitasking fool. I managed to get the OS installed by forcing the system to bypass its system predefined through registry commands, but the important things were wrong, as Windows Update does not work, so I'll try to reset all with only recovery disks. So far, no go. I am extremely tired, frustrated, and it's late, so apologies for what I've left out or of typos. Any help on how to solve this problem is GREATLY appreciated.

  Thank you very much for your response, @MechPilot. I actually found what I thought, it's perhaps the question a day or two before your answer: my computer was manufactured and purchased just before October 2010, which has been cut for restoration placed disks shaped for the drives non - Advanced Format. All the following which has been reformatted accordingly. I contacted HP and bought the replacement of the recovery discs (made in 2012), that I received yesterday. After several hours of nerves and finger-crossing, it worked like a charm. The operating system has successfully recovered, and I couldn't be happier!

  I answer computer said of office right now, in fact! Thanks again.

• Unable to join the homegroup - when you attempt to join I get this message: cannot create a homegroup on this computer

  I tried all the suggested 'fixes' and am still unable to join. My network has worked well until I installed W7. I can create a homegroup on any computer (I have 4 on the network), but no other computers can join. All I get when you are trying to reach is "impossible to create a homegroup on this computer". It is a problen very common, judging from all the complaints I've seen on the forums. With no exaggeration, there are thousands of people are unable to use this 'easy '... home network Please don't tell me to disable my firewall or computer time sync or one of the other "fixes" that do not help.

  Hello

  Since you're so desperate, you can configure the network to the office network.

  It's a little more work than the collective dwelling, but the results are more flexible.

  -----------------------------------------

  Here you have the whole story because what Win 7 can make wise network.

  Win7 when configured on the peer-to-peer network has three types of configurations of sharing.

  Homegroup = only works between Win 7 computers. This type of configuration, it is very easy to entry level users to start sharing network.

  Network of home or work = fundamentally similar (and better) to the previous methods of theWorking Group sharing which allow you to control what, how and to whom the records would be shared with.
  
  Public share = network Public (as Internet Café) in order to reduce security risks.

  For the best newspaper of the results of each computer screen system and together all computers on a network of the same name, while each computer has its own unique name.

  http://www.ezlan.NET/Win7/net_name.jpg

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted
  Please Note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic.

  If you end up with the 3rd party software uninstalled or disabled, make sure that Windows native firewall is active .

  ------------------------------

  If your network consists only of Win 7 and you want a simple network, use it.

  Group residential-recommended-links - http://windows.microsoft.com/en-US/windows7/HomeGroup-recommended-links
  Homegroup - frequently asked questions - http://windows.microsoft.com/en-US/windows7/HomeGroup-frequently-asked-questions
  Why can't I create a homegroup? - http://windows.microsoft.com/en-US/windows7/Why-cant-I-create-a-homegroup

  Change-a-group home-password - http://windows.microsoft.com/en-us/windows7/Change-a-homegroup-password
  How to leave a homegroup - http://windows.microsoft.com/en-US/windows7/Leave-a-homegroup
  To turn on/off and set the IPv6 components - http://support.microsoft.com/kb/929852

  After you have configured the homegroup, scroll to the bottom for the Permission/security section.

  -----------------------------

  Network Win 7 with another version of Windows as a work network (works very well if all computers are Win 7 also).

  In the center of the network, by clicking on the type of network opens the window to the right.

  Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.

  http://www.ezlan.NET/Win7/net_type.jpg

  Win 7 - http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows

  Win 7 network sharing folder specific work - http://www.onecomputerguy.com/windows7/windows7_sharing.htm

  Vista file and printer sharing - http://technet.microsoft.com/en-us/library/bb727037.aspx

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040

  In Win XP Pro with simple sharing Off, you can visually see the Permission/security level and set them up at your convenience.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP - http://support.microsoft.com/kb/875357
  Windows XP Patch for sharing with Vista (no need for XP - SP3) - http://support.microsoft.com/kb/922120

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  -------------

  If you have permission and security issues with Vista/Win7, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  ** Note . All the users who are allowed to share need to have an account onall computers that they are allowed to connect to.

  Everyone is an account, that means a group of all users who already have an account now as users. It is available to avoid the need to configure permission for each on its own, it does not mean all those who feel that they would like to connect.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET