Cannot install win10 using iso file training camp

Similar Questions

• Cannot install Win10,

  Win10 upgrade fails with the same code each time (it takes 20 times) code is c19001-40017

  "Configuration settings" is the final phase and fault codes look like c1900101 x400xx. The most common failure here is 40017, which means we could not start. Since this is the first time start us Windows 10 with all the drivers in place, once again, drivers are usually the cause of the accident. These issues tend to be less transient than the 30018 s, then a second test is less likely to solve the problem. Yet, it never hurts to try.

  try to upgrade manually:

  Option 1:

  Download the media creation tool

  Click with the right button on the MediaCreationTool.exe file and then click on run as administrator.

  

  Note: How to check if you are downloaded or installed the update Windows 10 November

  How to create an ISO or USB drive.

  Select upgrade this PC now and then click Next

  

  Option 2:

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10

  then

  • How to download official Windows 10 ISO files
  • How to: upgrade previous versions of Windows using the file ISO for Windows 10

  then

  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader).
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a thumdrive device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).

• iDrac6 - cannot start the virtual iso file:

  I just bought 12 x T610 I put in all the country. I know I could call the support for this, but I tried and there is no knowledge on this subject was available when I called the support:

  The problem: I'm unable to boot from the virtual media (iso file)

  I don't know how to do this, but I understand that I need to start the remote console and select virtual media > launch virtual media.

  Next, I add the iso file I want to boot from.

  I tried to start it, but it does not work.

  When I try to map the drive (still in the launch of virtual media), I get the error:
  Disk error
  Or other virtual media is detached or
  Redirection of virtual media for the selected virtual disk drive is already in use.

  I tried this from dozens of different computers and it is not going.

  As first boot device, I tried Virtual CD/DVD/ISO, but it didn't go.

  So. How do I file to mount the ISO and boot on them? IDRAC is loaded from another server using IE8 on the same subnet as the server that I am trying to start (gigabit). The iso file boots very well when mounted using vmware etc. (190 MB)

  I found the solution from dell support:

  I had to open idrac. go to system > console/media, and then click configuration and activate the virtual support.

  I thought that I had already checked this, and the cause is iDRAC has a blue for the active tab text, and black for the tab you are NOT in.

  Example:

  Redirection of the console and Virtual Media

  Configuration

  While Configuration is NOT active! You must click on Configuration, even if it is not marked as a link. Blade programmers :)

• It cannot burn DVD from ISO file.

  I can't burn an ISO file that Proshow Gold (PSG) made to burn a DVD on my DVD.  PSG made the file ok and it seems complete with what files I expect on a DVD, but if I right click on the file... Win 7 does not have the option "BURN to DVD".   If I try to burn the file manually... I get an error that says: "not a supported file Type.

  I played with it for 2 hours... What am I doing wrong?  (Note: I burned the DVD before, but never with an ISO file.)

  I can't burn an ISO file that Proshow Gold (PSG) made to burn a DVD on my DVD.  PSG made the file ok and it seems complete with what files I expect on a DVD, but if I right click on the file... Win 7 does not have the option "BURN to DVD".   If I try to burn the file manually... I get an error that says: "not a supported file Type.

  I played with it for 2 hours... What am I doing wrong?  (Note: I burned the DVD before, but never with an ISO file.)

  =============================================
  The following article might be worth a visit:

  Windows 7 - burn a CD or DVD from an ISO file
  http://Windows.Microsoft.com/en-us/Windows7/burn-a-CD-or-DVD-from-an-ISO-file

  And... the free ImgBurn is another option.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  Ignore most of the download buttons and click to the left of the
  green circle with the white arrow... He says...
  «Click here to download»

  Download ImgBurn:
  http://www.Digital-Digest.com/software/download.php?sid=470&SSID=0&did=1
  (The download is: SetupImgBurn_2.5.7.0.exe)

  (Windows XP / Vista / 7 / 8)

  (During the installation there will be an option to install
  Shortcuts of UniBlue and the "Ask Toolbar"... you can
  you want to deselect those)

  The following tutorial is maybe worth a visit:

  How to write an image file to a disc with ImgBurn
  http://Forum.ImgBurn.com/index.php?showtopic=61

• virtualize windows 7 triple boot MacBook pro using fusion - no training camp

  Hello. I know I've seen many, many messages online on using Bootcamp, but here is my situation. Once again, sorry if this has already been - I searched for a long time, read many messages from Woodyz and others, etc...

  I have a triple boot MBP - refit on/dev/disk0s1, Snow Leopard on/dev/disk0s2 (HFS +), Windows 7 Ultimate 64 (NTFS) on Ubuntu 12.04 LTS 64 (ext4) on/dev/disk0s4 and/dev/disk0s3.

  I'd only (for now) to be able to run the Mac Fusion to run Windows (Visual Studio is the primary reason and other members of my group are those of windows).

  That's what I tried:

  1.) not mounted/dev/disk0s3 of disk utility

  2.) / applications/VMware\ Fusion.app/Contents/Library/vmware-rawdiskCreator/dev/disk0 3 WIN764 free (once I tried ide) to create

  3.) Ran Fusion Version 4.1.3 (730298) to get:

  New-> continue create a virtual machine-> custom-> etc etc that up a localized vmwarevm in the Virtual Machines folder...

  4.) I then change, with a mac Editor (nano), the vmx in this file to add:

  scsi0:1.present = 'TRUE '.
  scsi0:1.virtualDev = "free".
  scsi0:1.filename = "... / WIN764.vmdk" (because the 2 files created by rawdiskCreator are just above this vmwarevm folder.

  When all this is done, I just get the rotating bar of DHCP and it says no operating system is located.

  I can't find instructions step by step for those of us who do not use bootcamp...

  Any help is greatly appreciated!

  Steve

  Occasionally, I need to create a Virtual Machine using a physical hard disk, temporarily placed in a FireWire enclosure, so what I do is to create a regular file based VM using VMware Fusion and make sure that vHDD of the machine virtual is on IDE.  Then, I use vmware-rawdiskCreator and create a set of files hard for the pHDD as like an IDE drive.  I then manually remove existing hard (empty) files of the virtual machine and place those created with vmware-rawdiskCreator in the packaging of the Virtual Machine and make the changes in the .vmx config file above.  Now depending on the physical Machine, the pHDD came and what OS is installed, I have to first start the Virtual Machine with an ISO Image of the custom of a boot disk WinPE that I then inject the required drivers for disk controllers HARD & keyboard and Windows registry entries when a Windows OS and any additional settings that may be necessary.  This is done to avoid type 0x7 BSOD, etc..

  Note: When it is necessary, you will WPA (Windows Product Activation) and other issues of product activation type to be processed when doing this and not all product activation type number are rectifiable so keep that in mind.  Windows and Microsoft Office should be supported by VMware Tools, but others will require creative, if possible solutions, if their manufactured products will not support this usage scenario.

  For some information on what is required I basically used information in the importer.iso in the bundle of VMware Fusion.app to validate my own scripts/programs to do the same thing as VMware Fusion as if it was done on the Boot Camp partition.  The content of the .iso make good reading, if you understand such things.

• Cannot install flash, using the latest version of Firefox

  Hi computer noob here.

  Operating system Windows Vista 16 b, browser Firefox V 3.6.23

  Im having some problems with adobe at the moment, first when I tried to install flash on a friends lap top now have downloaded a DLM, then when it is installed it does nothing, I still have no flash, then I come back to adobe and try to download again and he always tells me that I need to install a missing plug-in so it can download... when I click on 'install missing plug' it says Adobe cannot Download the missing file, it gives me the option to download it manually but when I try that it asks me to find a program to open it with? It seems that something does not work properly, please help! Why can't I just go to adobe with Firefox, click on download and restart my browser, it would be so much easier lol

  Second problem, the Windows XP operating system

  Second problem im seen last week is I can not connect to adobe to update my adobe reader software, it keeps telling me that it cannot connect to the server and it stops timing? Is there a problem with installing more recent readers because I tried to update another friends comp too and I had the same problem

  Thanks for the help

  Flash Player: do not use the DLM - it causes no trouble!  Download executable installation programs from http://www.adobe.com/products/flashplayer/fp_distribution3.html

  Adobe Reader: I don't know why the Updater does not; Download the latest version of the player directly from http://ardownload.adobe.com/pub/adobe/reader/win/9.x/9.4.0/en_US/AdbeRdr940_en_US.exe

• [G4 Pavilion] Starting from 8.1 to Windows cannot install DVDs using the UEFI.

  I have a g4 of Pavilion which had 8 Windows installed, until I decided to upgrade to Windows 8.1. I followed the instructions I found in other posts on this forum to be able to boot from the installation DVD - I had both disable secure boot and enable legacy Support, because otherwise, the system ignores the DVD drive (it is not even appear in the F9 Boot Menu if Legacy Support is not enabled!). The problem is that my HARD drive is formatted in GPT partition scheme, and the DVD of Windows 8.1 fails to install the OS on the drive when starting in the traditional Mode.

  What should I do to be able to start on the DVD Setup mode UEFI? I even tried to boot from inside Windows 8, itself, using the options advanced boot, but as soon as the system reboots, UEFI throws an error indicating that the computer is unable to boot from the DVD. I know that the DVD is * NO * damaged in any way since 1. I am able to start inside in the traditional Mode and 2. I was able to start it in UEFI mode on another computer.

  I had actually done this, but install the 'dirty' update messed with stuff I had installed so I decided to do a cleaning.

  Anyway, I solved the problem on my own (I discuss with a very nice representative of HP chat support, but she could not give me a solution that does not necessarily need to reformat the entire disk to an MBR partition scheme) through the following steps:

  1. created in a single file system FAT32 on a 8 GB USB key.

  2. copy the contents of the installation on the USB DVD. I thought that the root of the problem is that the system is not allowing me to access the DVD player at the start, I might as well try to see if it recognizes other files systems.

  3 restarted, you press F9 to start and selected the USB in the list of available boot devices.

  4 here, managed to start the installation on the UEFI mode Win8 DVD, as well as the installation worked flawlessly.

  So, it's the thing people. It still sucks that it is necessary to go through all this trouble to install an OS, however.

• Cannot install printer using Add Printer

  Cannot use add printer to install the printer.  I have the windows disc and reach a point which requires a disc HP.  How to find who have no idea.  And the installation process stops.

  famman,

  Unfortunately, if the printer is out of warranty there is no way to get free phone support, you can choose the charged incident. If you have a few options, take a look below:

  1. try to install the printer on another computer running XP.

  2. try to set up a secondary connection (Ethernet) option see here: installation of the software product in Windows XP to a network connection wired (Ethernet)

  If you try them without success, then I suggest contacting phone support.

  Thank you

• How to use ISO files in VMWare 9?

  Hello, I have the problem that I can not use the ISO 9 VMWare files.

  I had the same problem with VMWare 8 but there is a work around in 8.

  Use DeamenTool Lite and ISO was usable.

  But it don't work in 9 and mount the ISO with adjustment does not work too.

  Any ideas?

  PS I am running Win 7 Ultimate 64-bit and passed VMWare 8 to 9 when I change my PC.

  You need the problems then.

  1. can you check the iso in to other VMS as well of editing?

  2 have you tried to remove the Cd rom and Add again in the virtual machine of vmware workstation.

  3. check the file for the virtual machine's .vmx impact and see if the cdrom ide settings are correct

  http://sanbarrow.com/VMX/VMX-CD-settings.html

• Cannot install/uninstall/use flash

  recently, I uninstalled flash in order to install a new version,

  After this I discovered that I could not install flash and although

  Flash has been removed some animations could play.

  In addition the ' words of the flash animation"or who assured me that the flash was still installed.

  I uninstalled it through Control Panel, a fatal error.

  Since then, I have tried several times to use the flash uninstaller.

  I tried to download the special system tools.

  I searched and deleted every file and every registry entry

  the name "flash", "macromedia", "adobe" etc.

  I removed all visible traces of any adobe product just to be sure, with "Revo uninstaller".

  I have uninstalled/reinstalled opera.

  and then I used a registry cleaner several times.

  I looked through countless discussions to get help.

  I can not install any version of flash.

  page "about the flash animation" always tells me that I have installed flash.

  is there something more to do?

  the only thing I can think of is reinstalling windows,

  or buy a new computer.

  or if someone let me know the location of each file

  and the associated with flash registry entry so I could remove them.

  On Windows 7, 32 bit installation for the plugin paths are

  For Microsoft Internet Explorer

  C:\windows\system32\Macromed\Flash\Flash10x.ocx

  For Mozilla Firefox

  C:\windows\system32\Macromed\Flash\NPSWF32.dll

  Read http://kb.mozillazine.org/Flash and http://kb2.adobe.com/cps/141/tn_14157.html

• Tecra M10 cannot install OS using disc SSD Kingston

  Hi all.

  I am a computer tech and can usually find a way to fix something myself, (rock Google!).

  But recently I had a Kingston SSDNOW 64 GB drive and decided to install in my Tecra M10 age of 12 months. 4 weeks ago I had a full head of hair, now I am completely bald.

  The drive is recognized in the BIOS, but whenever I try to install Windows on it, I get nothing. I tried the recovery DVDs XP, recovery DVDs Vista The, the "free" upgrade Windows 7 recovery DVD, and a DVD Vista & Windows 7 retail. I can't drive to be recognized to install Windows.

  I can copy the existing disk image, but it starts the splash screens and blue. Normally I think that driver RAID or hard disk controller, but Kingston assures me that there is no requirement on the one hand, (and a standard SATA drive does not require a, I tried).

  I checked and installed the latest version of the BIOS for laptop. There is no update available for the SSD firmware. So I find myself with a laptop that always uses a slow, (relatively) hard drive and a very pretty silver rectangular Clipboard.

  Can anyone think of anything whatsoever that I missed. Anyone working for Toshiba can tell me if there is a BIOS update for this problem (I search the forum and found many people who are struggling for SSDS working in Toshiba laptops)?

  The sad thing is that the former other laptop I got for my son accepts the player and works fine!
  I had many prefer to buy Toshiba, but I want SSD technology rather sooner than later, and if Toshiba does not go to support, I might have to change of Lenovo or Acer.

  Rob.

  > Normally I would RAID driver or controller hard drive, but Kingston assures me that there is no requirement on the one hand, (and a standard SATA drive does not require one, I tried).

  I think you have misunderstood something the SSD drive does not need SATA drivers BUT the fact the OS (Win XP, Vista or Win 7)!

  The SATA drivers are needed to recognize the HDD/SSD under Windows OS.
  New generation of portable supports the new SATA controllers that require SATA drivers.

  You will find on the European driver Toshiba Intel Storage Manager page

  Intel Storage Manager contains the SATA drivers that are required to install the OS.

  Welcome them

• Excite AT10PE-A-105 - cannot install and use USB driver

  Hello

  I bought the AT10PE-a-105 and I never managed to install the driver for debug applicatoin android with eclipse.

  I use Microsoft 8.1 64 bit (last updated).
  I'm following the available tutrorial (RTFM).

  Even I'm a fan of the home user, I need to root and the USB driver works. I post a bad review on gsm arena.

  Someone was able to use the USB driver?
  [usb driver | http://support.toshiba.com/support/viewContentDetail?contentId=4001813]

  I lose 2 days trying to install the usb driver without success and I give up.

  Material may not be updated compared to the pilot then could developer team Toshiba could do a upgrade from usb?

  Concerning

  + The message was edited: link has been removed not allowed.

  Your excited AT10PE-a-105 was released in the European region and it seems to be the right Android WinUsb driver

  http://support.Toshiba.com/support/viewContentDetail?ContentId=4001725

  The driver has been released for the operating environment
  Windows XP SP3 or later (32-bit Version)
  Windows 7 SP1 or later (32-bit / 64-bit Version)

  8.1 Windows isn t taken in charge and I guess this is the main reason why you can not install the driver on your system.

• Cannot create PDF using Excel files

  I use Acrobat PDFMaker 5.0 for Excel convert PDF files to send to the clients of my bills, but for some unknown reason, it suddenly stopped working. He begins the process of conversion OK but then freezes and just hangs. I can continue to use my PC, but the CPU usage shows that 100%. I find myself either having to cancel the conversion or close the program completely by using the Task Manager.

  I'm afraid that I'm not savvy computer very, but I really need to find a solution to this problem as soon as possible.

  Please can someone help me?

  Thank you.

  Thanks for the replies, I found the solution partly by accident. I tried others with a similar problem and google the AcroTray mentioned by Bill@VT. My PC has been running slow lately and a colleague ran msconfig and stopped the Acrobat Assistant to run at startup to the top. I allowed again and now I can convert my files again, although slowly sometimes!

  Thank you for all your help, it is greatly appreciated.

• Cannot install the latest critical files 6

  Hello.  The last update "critical" Microsoft, for some reason some will not be installed. He tries when signing up, over and over again and then said you need to install.  Tried manually and error... Code 646 and Code 643.  Someone knows how can I fix?

  Thank you very much.

  http://support.Microsoft.com/kb/923100

  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0, or 3.5, you may receive code error Windows Update "0 x 643" or Windows Installer error code "1603When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive the code of error Windows Update"0 x 643"or Windows Installer error code"1603"

  For 646:

  http://www.Microsoft.com/downloads/en/default.aspx

  Put the KB numbers in the search at the above link > download them manually.

  If this does not solve it:

  Windows Update Forum:

  It comes with Vista, upgrade install and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon

  Mick Murphy - Microsoft partner

• I have lost/misplaced my win xp 64 bit disc also cannot locate the downloaded .iso file

  The original download link is no longer valid.

  I have 5 copies of windows 7 and recently bought 3 copies of Windows 8. Despite this, I have several elements such as KW-399U dual TV/Capture

  Pluscom usb dongle pic PCI TV/Capture card that refuses to install it. The manufacturers have provided updated drivers. Since I have a couple of spare mobos etc, I thought to re - incarnate XP. On a personal note, I'm 79 years old and feel that a quick response would be appreciated!

  Greetings to all

  Vale of Mauritius

  Hi Maurice Vale.

  I don't have a legitimate website, including Microsoft, where you can download a legal copy of Windows XP Professional. Your question is confusing as to what exactly you are trying to accomplish. If you try to go back to the original OS that's installed with your system, it still may be possible, depending on the type of installation you performed when you upgraded, and if, before the upgrade, he had available recovery partition.

  In order to further assist you, we will need more information about your system, specifications, what was made for her since you bought it first, what you're trying to do now and why it might be failing. You have the original installation CD? Did you harware changes? What is the current operating system installed and is operational?

  Looking forward to more information from you.