Cannot Wireless network Management Application

Similar Questions

• Cannot detect wireless networks or start the autoconfiguration Wlan service

  I locked my phone on thanksgiving day and came back later that night and connected... and my Wifi wasn't working. It shows all the available networks.
  

  -I am still able to connect to the internet via the Ethernet cable
  -My wifi switch is in the on position
  -In the Device Manager it says that it is WORKING CORRECTLY
  -It displays a red x in the taskbar, indicating that theres no link and no network available
  -When I go to control panel > network and Internet > network and sharing Center Center it is completely empty, nothing is there... only 4 icons... nothing else.
  -It does not show the button wireless in Windows Mobility Center more
  -J' bought a Linksys wireless adapter and it will not work unless I have activated the wireless network Manager windows... which I am not either.
  -J' uninstalled and reinstalled the drivers from the Web from Toshiba site
  -J' did a system restore and it didn't

  -My modem works fine

  -Other home computers are able to connect to wireless modem

  This is what it says when I try to start Wlan AutoConfig 0xc00ce508:0xc00ce508 of error «Windows failed to start service autoconfiguration WLAN on local computer»

  I did a 'sfc/scannow' in the administrator command prompt and it said "protection of resources windows found corrupt files but was unable to solve some of them"

  Nothing works.

  Please help me, it drives me crazy. Thank you very much in advance :)

  Hello

  If everything checked OK wise network, and you have mentioned before: ' sfc/scannow' in the command as administrator prompt and it said "windows resource protection found corrupt files but was unable to trouble".

  It is perhaps that some kernel files are corrupted and cannot be updated.

  Refresh the Installation of XP.
  

  To be safe, back up your data and some special stuff to a flash drive.
  

  ----------------------------------

  Boot from the original XP CD. Pass the first screen offering Console repair and proceed as if you install a new XP.

  After accepting etc., the new Setup screen lights up and would detect the current XP installation.

  You have an option to press R to repair.

  Use it, would take about 45 min. and you would an Installation of XP refresh all by keeping your Application, data and XP configuration.

  P.S. If you have made changes to the WinXP definition (special permission as firewall) security to look on them after the update because they could go back to the default value.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Mac OSX 10.8.4 can't see 5 GHz Linksys EA6500 wireless network

  Hello

  We have an EA6500 of Linksys router work of office. I found that Macs can't see 5 GHz network quite often but can almost always see the 2.4 Ghz network. If I restart the Mac then it can sometimes see the 5 GHz network but it's far from being reliable in trying to connect.

  Once all connected works correctly, it's just the operating system to display a list of network. If I same boot Mac in Windows 8 he can see the 5 GHz Wireless reliable every time.

  The office is in a shared office space, and there are many visible wireless in the room, about 12 now.

  I have the latest firmware of the router Linksys EA6500 (1.1.28.147876) and all software updates on Mac OSX. I fiddled with the network of automotive channels, to the setting of specific channels that seemed empty when I used a phone Android to see how busy they were.

  Has anyone seen or had any sort of resolution?

  When I get home, I have the same router and my Mac connect reliably, 100% of the time on the 5 GHz network.

  Well, I got to the low fo this. My steps, in case someone knocks something similar were:

  1. start of Fedora Core 19 Linux on my Macbook Air

  2 tries to connect to various networks near me, even if I didn't have the key

  3. notes that dmesg responded with 'country setting code' and then run dmesg and grep'd for the game of country codes

  4. after hitting one of the wireless networks, I noticed he would lie TW country code

  5. wireless network was not protected and so that a scan of the network, when her and found some web interfaces

  6. connected to the interface web and found it was a VCR Panasonic connect you

  7. once I had the wireless network manager I walked around the building with my iPhone looking force wireless looking where he was stronger.

  8. since I found that the reception office was where he was

  9. the person at the front desk denied that they had any router or wireless, it

  10. they opened a closet that had, a TV Panasonic inside recorder!

  11 identified the router right next to him.

  12A obtained in the region of router has changed for US

  Mac connect now to 5 Ghz EA6500 reliable, every time.

• XP computer. Connect wireless but cannot continue to the internet. Message from State windows is not currently managing your wireless network.

  How can I change my connections by which windows manages my wireless network.

  Hello

  You must ensure that the sellers utility nWireless does not load upward at satrtup.

  Then, http://www.ezlan.net/wzc.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Cannot connect Win 7 Ultimate to my secure WPA2 wireless network

  Any suggestions for how to connect to a wireless network secure n.   Currently running Win 7 Ultimate 64 bit and cannot get the sysytem works correctly?

  Hello

  Maybe this can help
  

  There is an inherent Catch22 to attempt to repair a computer wireless through wireless. Given that the without wire is not connected to the source, there is no interaction between the wireless source and the Wireless Client and no frame of reference to find what works and what does not.

  As a first step, I will temporarily move the computer to a place close to the wireless router and plug with a wire.

  When he works with a wire, switch Off the Wireless Security in the router, disconnect the wire and try to make wireless work. This must be done when the computer is always close to the wireless router to compensate for the weak, and or blocked the signal that could be part of the problem in the new suite spot work.

  In the computer itself.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• ConfigFree: windows pop up message: sellers application is controlling the wireless network adapter

  Hello

  When I draw a line from nearby wireless networks (with or without WEP security) to the laptop in the middle icon,
  a popup message with the text: the provider application is controlling the wireless card.
  Does anyone know what this message or where I can get the answer to this question?

  After clicking on it you may see far (only the 'ok' button is available), the connecting line with the laptop wireless network disconnects after
  a few seconds.

  Thanks a lot for helping me...

  Hello

  In my opinion this message appears because a 3rd WLan utility configures and controls the WiFi connection!
  There are different possibilities:
  The laptop uses the Intel wireless network adapter and the Intel Proset utility configures the WLan
  Or
  The laptop uses the Atheros WLan card and Atheros Client utility configures the WLan
  Or
  The windows have the option has been enabled and do this job.

  In this case ConfigFree application cannot configure and control the WiFi connection!

• Laptop HP Pavilion G6: after upgrade windows 10 - cannot detect wireless network

  Hello

  I upgraded my computer windows 10 laptop and it cannot detect a network.   The network adapters that appear in the Device Manager - controller Realtek PCI FE and Qualcomm-Atheros 802.11 AR9485 wifi adapter but I can't see any network.   I tried to install several drivers for Atheros without success.   I went back to windows 8.1 and network drivers works, I have upgraded to windows 10 back and I can't connect to wireless networks. I tried to update the drivers without success, uninstall and reinstall without success, I have alos tried the solution published on the microsoft unsuccessfully Web site: https://support.microsoft.com/en-us/kb/3084164

  I get an error message saying "the system was unable to find the key to register specified or the value '. '" I didn't install any software VPN or another, is there a solution to my problem?

  Hi there @tikaro23,

  Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I understand that you have a problem with your Wi - Fi on the laptop HP Pavilion G6. You mentioned that you can't detect a wireless network.

  I did some research and found a great document for you called HP PC - troubleshooting wireless network and Internet.

  What happened with you have attempted to use the resolution of the problems mentioned in the link you so much?

  Have you tried to restore the BIOS?

  Have you tried to connect directly to the Modem/Router?

  Have you tried to boot mode safe?

  You can maneuver in Mode safe without problem?

  In my research, I also found a Support Forum on the page called Microsoft Community after upgrading Windows 8.1 for Windows 10, no wireless networks are available.

  There is a post of RajithR. Read his message in its entirety. (I also provided it below.)

  

  You said you tried to uninstall the driver. Are - what you got to do it in the order shown below?

  • Uninstall the driver of network card in Device Manager,
  • Reboot the laptop twice,
  • Reinstall the driver.

  Please use the HP Support Assistant, it will help with the software and drivers on your system at the time of purchase or this update of need.

  I know you said you tried to update the driver also. Have you tried to do it in the Device Manager in the order given below?

  • In the Device Manager
  • Click the network adapters to expand
  • Right-click on the network adapter family
  • Select software update of the driver
  • Choose search for automatically updating driver software.
  • Once the installation is complete, restart your laptop.

  Please follow the troubleshooting steps above and the re-post with the results, information from the above questions and HP Pavilion G6 Notebook PC model number.

  Thank you!

• "Cannot connect to the network." When you enter the correct password for wireless network

  Hello

  I have the HP Photosmart C7200 all-in-One series.

  This seems relatively insignificant compared to some of the problems posted here, but nevertheless it is a problem.  I have a Verizon FiOS (Actiontec) router.  I am trying to connect to it wireless; the network key is using WPA authentication.  I followed all the instructions in the quick start guide.

  My printer detects my network and application authentication key.  I enter the correct key, the printer is trying to establish a connection, but after about 15 to 25 seconds, I get the error message, "cannot connect to the network.  I know that my key is correct; I connect to my router very well through several laptops, PDA, etc.  I have reset the settings network default manufacturer and tried without success.

  I don't know what kind of trouble shooting I'm supposed to do here.  The printer detects the router (albeit low signal strength) whenever I try to connect, I enter the password each time and I get the error each time.

  Your help is greatly appreciated.

  Edit: I printed the test report wireless network, here are the results:

  Radio on   PASS

  The radio work   PASS

  Ethernet cable not plugged in   PASS

  Network name (SSID found)   PASS

  Security   PASS

  The printer settings compatible with the configuration of the wireless router   PASS

  No filtering   IN CASE OF FAILURE

  Connected   Not work

  The signal strength   Very low

  Other networks detected matching you the network name (SSID)   NO.

  I know this sounds strange, but try changing channel by channel 11 of the wireless router.

• Yellow triangle with! the wireless network connection in the task bar icon, but ok in Device Manager

  I still need help: 11-24-10' uncorrected problem after all

  I have a laptop of refurbished HP older Pavilion ze5385US who has recently lost the wireless connection.  Now, I have to leave it plugged in to use, not practical at all.  I did the right click on the icon to open the network connections, left clicked wireless network connections and then clicked "repair this connection.  The uninstaslled of the computer, and then was not able to reinstall.  When I checked D, it was empty.  I thought it was where restoration stuff should have been.  So I downloaded and reinstalled much Express IEEE 802.11 PCI card Lan, until I found the one that the computer would be except.  Now, it appears in device very good Manager, but has theyellow cone with! on the icon in the status bar at the bottom.  When I raised it lights, it is said: 13 of (ANY) wireless network connection, speed: 11.0 Mbps, Signal strength: Excellent, status: limited or no connectivity.  When I choose "View available wireless networks", I get "Windows cannot configure this wireless connection.  Under network without wire/support/details of connections, Iget physical address: 00-02-8A-92-BE-0C, IP address: 169.254.196.112 subnet mask: 255.255.0.0, then the default gateway, DNS server, WINS server & have not enumerated values. I'm afraid to hit the repair again, it could wipe out the only map I've found so far that is accepted by my computer.  When I try to enter the knowledge base for WinXP, I get an error for this page, as well as several other help pages I tried the site of microsoft.com for help.  When I used configurationtool thewireless zero in respect of services & restart earlier, I had a red X on my icon, so I guess I've lost my card after all.  Can I disable this?  The map always shows as OK in Device Manager.  Any ideas anyone?  I need help here please.

  Hello

  I thank you and wish you the same.

  I see that your problem has been solved using the HP driver that you mentioned on Thursday, November 18 in your message and the Express.sys is a problem with Windows install.

  I suggest to install the version of Windows install 4.5 on the system from the link below and then update the driver from the link that was attached to your question before and check.

   

  Step 1:

  Install windows install 4.5

  Windows install 4.5 Redistributable

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

  Step 2:

  Update the driver from the link you mentioned in your previous post.

  I suggest you to check with TP-link if this model is compatible with Windows XP or not.

  http://www.TP-link.com/products/ProductList.asp?class=WLAN#S6

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• When you try to run Linksys Wireless Network Monitor error: cannot load ProcNICs.dll, Can t Load Res_dll

  Original title;

  Linksys wmp54g & windows vista

  When you try to run Linksys Wireless Network Monitor I get the following errors:

  Cannot load ProcNICs.dll

  Failed to load Res_dll

  Linksys wireless adapter is installed and running properly, but I can't use the application linksys to establish a new network connection.

  Any suggestions?

  Thank you.

  Hello

  I suggest you contact Linksys for assistance:

  http://home.Cisco.com/en-us/home

  Linksys Support link:

  http://homesupport.Cisco.com/en-us/support

  I hope that helps!

  If you need help on Windows, please keep us informed.

  We are here to help.

• Cannot see wireless networks

  Hello

  I have checked through some of the forums, but couldn't find an answer that helps me, so I post here.

  I am running Vista Home Premium SP2.

  Until this morning, my wireless worked fine. Today, my laptop is unable to connect to any wireless network. I make sure that my router works fine (I am connected via my phone), my device driver is showing no problem in device manager, and my wireless switch is turned on. All other configurable in Control Panel Network is set to automatic.

  Any help is appreciated.

  Thank you.

  Hello

  Maybe this can help.

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  If all the foregoing is OK and it does not connect to the wireless router. Journal from any computer that is or may be connected to the wireless router with a wire, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security .

  When the work turns on the Wireless security.

  * Note, people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  ---------------------

  Stack TCP/IP work should look like.

  TCP/IP and its variables usually look like this.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  --------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• PC cannot connect to the wireless network

  Windows Vista and office computer HP.  The use of the Airport Extreme.

  All other computers in the House can connect to the wireless network.

  The Vista machine declined the connection Wireless intermittently for the past two weeks.  Tonight, he lost it completely.  When I click on "connect to network" in the network control panel - I see the wireless network.  But when I click on connect, I get a message that Windows cannot connect to this network.

  I changed the password on the Airport Extreme and rebooted, it.  Wireless usb on Windows machine the device works correctly, by checking through the properties box.

  For example, Vista machine is recognizing the wireless network, but does not connect. Why not?

  I'm ready to throw the computer out the window!

  Hello

  Check the PoodlesAway solution to the same issue here:

  http://social.answers.Microsoft.com/forums/fi-fi/vistanetworking/thread/d4fa044e-8C41-4D8D-a4b1-82ee9ff556ac

  ======================================

  Apple Airport may be your main problem - did you check its firmware?

  Read these
  http://osxdaily.com/2009/09/01/how-i-fixed-my-dropping-wireless-airport-connection-problem-in-Snow-Leopard/

  http://reviews.CNET.com/8301-13727_7-10331876-263.html

  ======================================

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• PROBLEM! Cannot view wireless networks!

  Hi, I am currently running Win 7 Ultimate 64 bit on my office and cannot view wireless networks!

  I tried to use two wireless adapters and both show active although they cannot show all networks.
  LAN works perfectly well and when I try to add a wireless network, it is said "an unexpected error has occurred."
  I have updated drivers for two adapters to the correct version wireless and little. No yellow icon in the Device Manager.
  I also checked to see if power saving has been enabled for the device and power options that are disabled.
  Two wireless adapters are using a USB port, not PCI. I abandoned everything simply! I need some advice on how to solve this problem! I can provide more information if necessary. But please help me with this problem :(
  I also disabled anti virus software and my firewall!
  The wireless adapter, I am using is the:
  TRENDnet TEW-649UB Wireless USB adapter N speed

  UPDATE! :
  We have some progress I uninstalled all the previous windows updates and can now see wireless networks (such as firewall/AV). The problem I have now is that when I try to connect it said "Windows could not connect. He also says in the settings of cards tab my wireless adapter is "authentication attempt.

  Hi Tatiana,

  ·         Have you tried to install the drivers from the manufacturer's Web site?

  ·         Have you checked if the network card works on another computer?

  Download drivers card network from the manufacturer's website and check manually.

  http://www.TRENDnet.com/downloads/list_subcategory.asp?SUBTYPE_ID=1353

  Alternatively, you can deal with this problem due to security software. I suggest that disable you the security like anti-virus and firewall software and check if the problem persists.

  http://Windows.Microsoft.com/en-in/Windows7/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Call the helpline for the manufacturer of your network adapter. It is likely that neither Windows nor the router have problems, it's just a matter of getting the configuration on both put in place settings to work properly together. The manufacturer of the router will be the best resource to learn how to configure their device.

  http://www.TRENDnet.com/support/

  For more information, please see the following links:

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-a-network

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  http://Windows.Microsoft.com/en-us/Windows7/add-a-device-or-computer-to-a-network

  http://Windows.Microsoft.com/en-us/Windows7/wireless-networking-frequently-asked-questions

  Hope this helps

• Intel WiFi Link 5100 network card - cannot detect wireless networks

  I have a HP Pavilion dv7-1270us. My wireless card is an Intel WiFi Link 5100.

  Running Windows Vista 64 bit, Ubuntu Linux, Linux Mint and Fedora Linux (various versions, all), the wireless works fine. My desktop computers to work with wireless cards to connect to the network work very well, and all computers (except mine) to connect to my home network very well; which means that it is not a problem with wireless networks, or with my network card. I try to manually connect to the network, but it can't find it. Diagnosis requires that the card is disabled, and that I should turn it on via the switch on my laptop running: fact.

  During the installation of Windows 7 64 bit, I cannot see wireless networks (and therefore unable to connect). Re-formated and reinstalled again, check the wireless connectivity between each batch of Windows Update, but it has never worked.

  I downloaded the latest drivers from Intel, via Microsoft Compatibility Center (version 15.2.0 driver).

  There is no system restore option because he has never worked as a first step, except in all other OS, I got on the computer. Microsoft Compatibility says the map is compatible, then Device Manager shows no problems. The network adapter is active via switch on my laptop.

  Happy that you guessed it sorted!

• My office wireless icon is x'd - cannot detect wireless networks.

  My computer screen suddenly went black this evening - the monitor was still, the fans were still humming, but it was totally insensitive.

  I forced a stop, and when I rebooted the computer, my wireless icon has been x'd out. My computer cannot detect wireless networks (there are a half-dozen or more in my building). I tried a good stop and restart, but the problem was still there.

  The Network Diagnostics tool told me to check the router, so I did--but all other devices in the House are connected very well. I thought it would be a malware, so I ran a MalwareBytes scan, which turned up nothing. Then I reinstalled the drivers from the card WLAN - no luck there.

  System Restore has not solved the problem. ipconfig says "media state: disconnected ' for my WIFI adapter, but I don't know how to fix this. In the devices, the Broadcom WLAN card Manager, he says "this device is functioning correctly.

  I work from home, so it is important that I can access my wireless. Help, please!

  Hello

  I imagine the inconvenience that you are experiencing.

  1. What is the brand and model of the computer network adapter?

  2. This error message with him modeling icon?

  3. do you have a code error message when you try to connect to the internet?

  Here are some steps you can follow to resolve the problem:

  Step 1:

  Check if the network adapter is enabled, if not, please go ahead and enable the network adapter. Please follow the steps:

  a. open network connections by clicking the Start button, then Control Panel. In the search box, type adapterand then, under center network and sharing, click view network connections.

  b. right click on the network card and do one of the following:

  -To disable the network adapter, click disable. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  -To enable the network adapter, click Activate. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, please see the link below:

  http://Windows.Microsoft.com/en-us/Windows7/enable-or-disable-a-network-adapter

  Step 2:

  Try to reset the TCP/IP settings:

  Reference:

  How to reset the Protocol Internet (TCP/IP)

  http://support.Microsoft.com/kb/299357/en-us

  Step 3:

  Flush the DNS and request a new IP address of your ISP server by following these steps.a. Click Start
  b. click on run
  (c) in the Run dialog box type cmd.exe and click OK
  d. in the command prompt, type the following.e. ENTER after each new line.
  ipconfig/flushdns
  ipconfig/release
  ipconfig / renew
  output

  See also:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.