Card mother IDE ok for CD/DVD writer?

Similar Questions

• I can find driver for my dvd writer dose not work Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) _ dvd writer ad - 7530 has ata thanks

  Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) has .dvd rw ad - 7530 ata

  Hello

  Code 39 means that the driver is corrupted or missing.

  Please make all below even if you have done some before as it is often the set of operations which solves
  the question.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  --------------------------------------------------------------

  Also check with your system manufacturer to see if there are any updated drivers for your DVD. Or even if it
  are you can reinstall the 'old'. Many use Windows default drivers however some special aura
  ones. Also check the website of the manufacturer of the car.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Card mother MSI MS for my desktop HP 7930 (albacore)

  Where can I buy a new motherboard or ued for my desktop HP 7930 (albacore) MSI MS? Shame on junk food, because it is in good shape. Much thaniks

  Try eBay or Google like these for example:

  http://www.eBay.com.au/ITM/MSI-Ms-7093-HP-albacore-GL6E-motherboard-SKT-939-RS480-/140562867008

  http://www.serversupply.com/HP-Compaq/motherboard/desktop%20BOARD/albacore%20GL6E/PW636-69002.htm

• Card mother OptiPlex GX 280

  Welcome to all,

  My OptiPlex GX 280 motherboard has finished its task and decided to stop working. I didn't find the precise name of the motherboard. I'm thinking replacing it or looking for DIY fix.

  It starts with one morning, when I turned on the POST test failed (the CPU fan works on RPM max (no beep)). I tested the PSU, RAM, hard drives, video card and all of the components, only the test of the motherboard have not been tested, according to the exclusion.

  I prefer the repair so I would be grateful to tours, trips or ideas if it's possible. More thank you for your assistance in advance.

  Best wishes
  David

  Genuine Dell OptiPlex GX280 card mother Systemboard motherboard for the system minitour (SMT), Reference Dell Compatible numbers: G5611, Y5638, U4100, H7276, FC928, U7915, K5146, KC361, XF961, XF954, X 7967

  http://www.Amazon.com/Dell-motherboard-SystemBoard-mainboard-compatible/DP/B003EUUMV0

  It's almost the cost of a complete system of GX620 minitower.

  The Board is mounted on a tray that comes out.

  

• DVD HP dvd200i drive: HP DVD Writer dvd200i installation software

  I removed my OEM HP DVD Writer dvd200i from HP Win XP machine died at a Win 7 machine.  It is not recognized, so I guess I need s/w installation.  Am I correct, and where can I get the s/w?  I searched HP support and can't find any s/w installation it for HP DVD Writer dvd200i model.

  What you need is not the installation software, but a driver.

  To appear in Device Manager?  If so, clidk right it and update driver.  It must install at least one generic driver.

  This isn't a young unit and unfortunately HP only provides drivers for it up to Windows XP.  You try to install the driver compatibility by right click on the downloaded exe file then compatibility mode.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=81681&

• Need drivers chipset card mother AmethystM (MSI-7184), for Vista 64 bit OS

  I'm looking for the proper chipset drivers, or compatible drivers, for the card mother MSI-7184. The chipset is ATI RS482 & ATI SB400. Specifically, I'm looking for the following drivers:

  PCI express filter driver - currently using Catalyst 8.3 ATI PCI Express (3GIO) Filter Driver

  Configuration AMD address map - currently using the standard driver microsoft

  HyperTransport (MC) Configuration of the Trace Mode - currently using the standard driver from microsoft and DRAM AMD

  AMD HyperTransport Configuration - currently using the standard driver microsoft

  Configuration of various AMD - currently using the standard driver microsoft

  ATI i/o Communications Processor LPC Controller - currently using the standard driver microsoft

  ATI i/o Communications Processor PCI Bus Controller - currently using the standard driver microsoft

  Communications ATI i/o Processor USB 1.1 OHCI controller - currently using the standard driver microsoft

  Communications ATI i/o Processor USB 1.1 OHCI controller - currently using the standard driver microsoft

  Controller ATI i/o Communications Processor USB 2.0 EHCI - currently using the standard driver microsoft

  Controller IDE ATA standard - currently using microsoft standard driver - it's supposed to be SATA I think that my HD is connected to it and its SATA

  Standard ATA IDE Controller - currently using the standard driver microsoft

  Bridge standard CPU PCI - currently using the standard microsoft driver - what is supposed to be ISA instead of the processor?

  PCI and standard PCI to PCI Bridge - currently using the standard driver microsoft

  I'm looking for drivers because my CPU usage is constantly at 45-60% usage. My processor is an AMD Athlon 64 X 2 4200 +. Devices and drivers of Thease are what Vista has recognized and loaded. I don't think that is correct. Any help on this would be greatly appreciated.

  Sean

  OK, I found the appropriate drivers!

  ATI drivers:

  Drivers of North Bridge: catalyst 8-12_vista32-64_sb_72277

  SMBus, & IDE drivers: catalyst 8-12_vista32-64_72274 - run the program so it extracted all files in c:/ATI do get out. Then manually install two IDE controllers and SMBus drivers by using Device Manager.

  Also, I solved the problem with the hardware interupts. The on-board USB controller and suport Legacy interfere with the video card. To fix this go into the BIOS and under Advanced, disable Legacy support. Then in Device Manager disable all three usb controllers. These controllers have been disabled as soon as the missing of interruptions. I'll get a PCI usb so I can still have USB ports.

  Message edited by shfire2000 on 01/26/2009 21:51

• Drivers Windows 7 x 64 for the card mother Memphis-M

  Hello! I bought the HP Pavilion 500-164er with Linux operating system desktop PC.

  Still, I installed Windows 7 x 64 on this unit, but I couldn't find some drivers for the card mother Memphis-M.

  I need:

  Simple communication controller PCI Chipset, USB 3.0.

  Thank you and waiting for a response.

  Hello:

  You can use the W7 x 64 drivers and software of this model that has the same motherboard as yours.

  DO NOT USE ANY BIOS OR THE FIRMWARE OF THIS MODEL FILES

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063 & LC = on & CC = US & DLC = in & sw_lang = & Product = 7049404 #N543

  Chip set:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=CP-134596-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 7049404 & sw_lang =

  Comms Simple PCI:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=CP-134614-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 7049404 & sw_lang =

  USB 3:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=CP-134611-1 & CC = US & DLC = in & LC = on & os = 4063 & Product = 7049404 & sw_lang =

• Need driver DVD writer for my Satellite L300

  Hi guys that I really need help.

  For some unknown reason to myself I have sewing to have deleted the drivers of my laptop DVD writer.
  It won't play or write disks, I have tried every disk there.

  Its saying the _archive is missin or corrupt_,
  I'm not sure that I now need to address this issue the drivers or so i ' l'll have to reset the settings of factor.

  * Can anyone please help, thank you *.

  Optical disc drive using the standard Microsoft driver and there is no special driver for this device. Optical drive should be automatically recognized by the operating system.
  What is the STRANGE situation in Device Manager?

  Of course, for getting new factory settings is simplest and easiest way to get it working again, and it can be done very simply - http://aps2.toshiba-tro.de/kb0/HTD9102IR0000R01.htm

• HP P6 2120t: possible cards for the card mother Pegatron IPISB-CU on a computer of 2120t HP P6

  So, I'm looking to upgrade my graphics recently. Over the months, I've been looking around and find out a lot about how work cards graphics, and I need to find one. However, what I don't know much about is the compatibility of graphics cards with card mother Pegatron IPISB-CU. I checked and I'm running on FRIEND 7.19 BIOS update 02/04/2012. It seems that I need to look for graphics cards that can work with "Legacy" BIOS. However, it's not not clear that even if I bought one it would work. I was hoping so to ask HP and the community if there was in fact a strong graphics card that would be 100% some works with my motherboard/BIOS card.

  To archive the many discussions of forums, it seems the MSI 750ti ( http://www.newegg.com/Product/Product.aspx?Item=N82E16814127783 & cm_re=msi_750-_-14-127-783-_-Product ) is my best bet because it is said to have a switch making it compatible Legacy Boot. However, read the description of the product, I have not found this mentioned in the features. What scares me.

  If someone could shed some light on what I'm working with. I would be extremely grateful. I'm ready for the possibility that there is no viable option other than buying a new motherboard and the OS, but if I can get away with upgrading my current system I would be very grateful.

  Thanks to all who take the time to read/answer

  Drew

  At the company MSI Web page in the master record for this MSI cardunfortunately didn't even State if power 6-pin PCIe connectors are needed. Also, it does not specify that there a dual BIOS or the old BIOS support. I wouldn't consider this one for your motherboard.

  You may need to upgrade the PSU as your installed PSU doesn't have 6 - pin PCIe connectors with power cable to power the card video update.

  EVGA and Gigabyte are also PCIe x 16 graphics cards with dual BIOS allowing a choice of inheritance or the EFI.

  Cards with BIOS double EVGA

  http://www.EVGA.com/articles/00767/

  I'd take a peek at the r7 of Sapphire Radeon 260 and higher and r9 in the 300 series Radeon cards. In fact, they have a physical switch on the map.

  Sapphire video card specifications

  http://www.sapphiretech.com/catapage_pd.asp?cataid=271 & lang = eng

  What is 100% certainty in the work with your motherboard, you upgrade a ready to use PC or a system as you put as well as components custom, studied and chosen by yourself.

  I suggest you buy your video card with your credit card. If this does not work with your motherboard you can return. Which takes an element of risk fomr away the attempt.

• 8200 elite format microtour, need of care technique for card mother/PSU

  Hello.

  I'm upgrading of the power supply in my Hp Compaq 8200 Elite format microtour.

  The /PSU motherboard uses an archaic connector that looks like a connector 6-pin inline with to the (http://i20.photobucket.com/albums/b225/r4ch3t/Aux-connector-148x200.gif). But it is connected with 4 wires (red/white, white, green, purple)

  To upgrade the PSU, I need to find a way to connect it to the new motherboard, but I can't find any information or datasheet for the motherboard or the power supply.

  Motherboard:

  SP #611834-001

  DG #611794-000

  PSEYU0JCY0W197

  AS #611793-003

  0J REV

  POWER SUPPLY:

  Model: PC9057

  PART NUMBER: 611483-001

  ALTERNATIVE NUMBER: 613764-001

  Where can I find more information about the card mother/PSU?

  What is the connector? It is standardized in some way?

  What is the combo of tensions/soil necessary for the pins?

  Thank you

  Your question would be better served in theHP Enterprise business community.  I highly recommend that you join the community and post your question there.

  This time, do not forget and give identifying information more accurate than you did in this post. In the image below, you will see how what gave you as a product identifier can be confusing.

  

• driver se-208 samsund dvd writer for windows 8

  I have a samsund dvd writer is 208 as worked well until I have install Windows 8 Pro. There is no software driver for windows 8?

  If you can read data cd and DVD, it works well. There is no video dvd player in no win 8 and also no dvd burning software not included with windows 8. You need to find a video player. VLC is a free dvd player.

  Windows 8 should provide the drivers win 8. See the Compatibility Center HERE.

• I want to improve my card mother and CPU on my PC. Can I use transfer windows settings for it?

  I want to improve my card mother and CPU on my PC. I like to keep all my settings from my games, etc, so I don't have to buy/purchase new and purchase/buy a new OS Win. I am running Win 7 Pro. What is the best way to address the issue? I keep my OS on a SSD and all the other stuff is on a separate HARD disk. Basically, I need to install the new chipset and other pilots MB.

  You can save files and settings and restore to the new installation of Windows, but the games cannot be guaranteed. Just give a try. If it works, it's fine. If this isn't the case, you must reinstall the games.

• Replacement card mother Qosmio G10

  After replacing the card mother a Qosmio G10-120 original Win Xp MCE with the official update (FC43S1 A5A001749010 P000454980 jury), some problems have arisen:

  1. second HARD drive internal no more seen.
  2. all buttons stop "standby/disable rebooting the computer" do not completely take effect (office closed way unexpected but manual power button continues to show the color blue and portable remains active).
  3. always on cooling fan.

  Upgrade the motherboard consisted of:

  1. creation of new channels DMI Council (in particular "Model name" field was set to "Qosmio G10").
  2. loading the CD-ROM TCN0000006 official update tool.
  3. no recovery BIOS or EC/KBC.

  Any idea?

  I m wondering how you did update the information in the DMI?
  As far as I know that the Toshiba authorised service provider is able to update information DMI as the model name, version number, etc. using utilities and special tools.

  I googled for the motherboard part number, you have deposited in your original thread, and it seems that this motherboard has been developed the Qosmio F15 series.
  So maybe his bad card mother

• The card mother MS-7184 (AmethystM) in my old HP PC takes in AHCI mode?

  First of all, thank you for taking the time to read my post!

  I recently bought an OCZ Aligity 4 256 GB SSD drive. I want to use the SSD as drive replacing the original hard drive in my old HP Pavilion Media Center TV m7334n desktop PC. Here is the link to my pc:

  http://h10025.www1.HP.com/ewfrf/wc/product?cc=us&LC=en&DLC=en&product=1821850

  I know that the motherboard identified on the Web site above for this model of PC is A8AE-(AmberineM), but the motherboard I have is MS-7184 (AmethystM), the specifications of the motherboard is here:

  http://support.HP.com/us-en/document/c00378480

  I updated the BIOS with the latest version (3.47, 03/03/2006) I can found on the HP website. In the BIOS, I can't find any info on the AHCI support. My questions are:

  1 - is the card mother MS-7184 (AmethystM) in my old HP Pavilion Media Center TV m7334n Desktop PC support AHCI mode?

  2. how to configure CMOS when I use the SSD as my main drive on the old HP computer?

  Note Please that I have aleady copy drive hard whole orginal on the new SSD and I started my computer on the new SSD. This works. I have another post questions on the recovery of the system on the SSD, the post is here:

  http://h30434.www3.HP.com/T5/desktop-operating-systems-e-g/system-recovery-doesn-t-work-on-cloned-SS...

  Thank you!

  You are the very welcome.

  I leave these settings at their default values.

  You have the SSD connected to sata port, and it must operate to the maximum 150 Mbps transfer speed, 133 or 100 no matter what readings are displayed, as would an IDE drive.

  The problem is that since there is no AHCI setting, the drive cannot enjoy the native command files or TOPPING.

  Aside from that, an SSD should be better that a standard SATA I mechanical drive or IDE hard drive.

  Even subjectively, you should 'see' a difference in sensitivity of disc, not you?

  Improved time, faster startup time for research, for example.

• Error 0X0000007E Stop after installing the new card mother and CPU.

  Original title: Stop error after installing the new card mother and CPU.

  After I installed a new motherboard and CPU I got a stop error 0X0000007E (0XC0000005, 0XB77EA756, 0XB84C742C, 0xB84C7128) and it restarted immediately. It always starts in safe mode, but I can't understand what is wrong. The old processor is a pentium 4 3 ghz, not sure what the motherboard was, new processor is AMD Athlon 64 X 2 Dual core 4200 + and I only know that the motherboard is an ASUS socket AM2. Device Manager does not recognize the CPU correctly, it shows just two entries called processor. As far as I can tell, it's almost certainly a driver issue, but I don't know how to diagnose or fix this. I am running windows XP home, I removed my video card, running 2 hard drives at 120 g (M) and 200 g (S), a DVD drive (M) and a reader of CD (S), and a stick of RAM to 1 GB.

  If you have made the change without having to reinstall XP, you will be taking and Pray H@ll. the best thing to do would be to reinstall XP and make sure you have the drivers available for your motherboard available so that you can update the installed chipset. In addition, be aware that if you have an OEM of Windows version, the license is dead when you changed the mother/CPU card.

  I hope this helps.