CD and dvd not recognized by Device Manager... are trying to reinstall, but that has not worked

Similar Questions

• Unknown device named "PCI data acquisition" and signal processing controller in Device Manager

  Greetings,

  Yesterday, my brother, who was running Windows 8.1 Overview on his Asus S400CA Ultrabook fell on a big problem of the NTFS partition corruption that made it impossible to recover through the Refresh Utility Windows 8.1. Given the situation, my brother decided it was better to go back to Windows 8, I had to install Windows 8 on their PCs by using an external DVD drive with a Windows 8 x 64 installer I already buy plenty of detail. The computer never asked me for a product key that I have read is normal in Windows 8 PC now having these embedded in the motherboard. So far an installation smoothly, but he's going to be delicate in the part of pilot facilities. Before you remove the computer I went to the Asus website and did my best to find the specific drivers for my brother's computer and downloaded the key drivers, chipset, audio, intel graphics card, bluetooth, trackpad Wireless LAN, LAN and Asus and installed. I used Device Manager to check that the drivers have been installed and which did not exist. I was able to get most of the drivers installed properly, however, said the Device Manager miss me the pilot of "Data Acquisition and Signal Processing controller PCI. Unfortunately I go to Asus website to see that if I can find the driver however, I can't do this right now.
  Check the attached screenshots for visibility...
  
  
  I also tried to use Windows Update to see if he could find the correct driver and unfortunately it's a dead-end. Because of that I write in this forum to see if someone can point me in the right direction when it comes to this missing driver (and others) indicated in the Device Manager.
  One last thing that I would ask is if I can use a utility like DriverMax to find missing drivers or should I go and install it manually?
  Thank you very much in advance for any help on this matter.
   
  Original title: cannot find drivers for Asus S400CA Ultrabook PCI

  Hi Mike,.

  Please keep us updated on the status of the issue. Please do not hesitate to answer, in case you need help with Windows in the future.

  Good,

  ASUS technical support according to my brother was a bit of a dead end, so I went to another Google search and found the culprit. I was missing the following drivers of ASUS:
  • Intel® dynamic and thermal platform frame driver
  • ASUS Wireless remote control (a driver for you to enjoy the airplane mode (Wireless) On / Off)
  The first pilot took care of the Acquisition of ICP data and Signal Processing controller and all but one of the unknown devices. Finally, the other took care of the last unknown device in Device Manager.
  I never thought that ASUS would use this a strange name for their driver because these names are extremely misleading.
  Other than that, I can finally say with certainty that the computer of my brother is back in business, and I can call this comprehensive process of restoration of Windows 8.
  Thanks for any assistance to Zaki J, I appreciate much all advice through this process!

• When I plug in an external hard drive usb, it is recognized in Device Manager, but not in Solution Explorer.

  When I plug in an external hard drive usb, it is recognized in Device Manager, but not in Solution Explorer. I use windows 7 on a laptop Pavilion dv7-6b77dx.

  Thank you.  I followed your instructions and it worked.  I am amazed by these forums.  No matter what a person has problems, there is someone out there who has the knowledge and the willingness to share with the less informed.  Thanks again for you information.

  lacroos

• Satellite C650 - USB ports not recognized in Device Manager

  When I turned off my cell phone, I lose the use of my two USB ports. The only way I can get back them is to use Device Manager

  Go into the Manager of peripheral devices, Bus USB controllers, there are 6 x Intel ICH9 Family USB Universal Host controller 2 x Intel ICH9 Family USB2 Enhanced Host Controllers and 7 x USB hub root. When I lose the USB ports, USB root hubs seem to disappear, and the only way I can get back them is to uninstall the controllers and then right-click Universal Serial Bus Conrollers for "scan for changes on the hardware. This brings back the root hubs and USB ports work fine... until the computer turns off again.

  Someone at - he encountered this problem and managed to resolve it? Its a hassle to have to go through the uninstall it / Reinstall procedure each time. Your advice will be appreciated.

  Hey Buddy,

  You use the version preinstalled Windows from Toshiba or did you install your own version? I don't see any information about the BONES in your ad...
  Theoretically, it could be a software problem so ports USB work correctly if they recognized in Device Manager

  You should also try to update the Web from Toshiba site chipset driver. Maybe it helps.
  Otherwise, I could imagine that the update of the BIOS can also operate and this update you can get on the Web from Toshiba site too.

• internal card reader must be disabled and then enabled in before Device Manager it will not work properly.

  Whenever I start my computer, my internal card reader must be disabled and then enabled in before Device Manager it will not work properly. I put an SD card in there and auto does not work. I check my computer and it shows that it is there, but when I double click on it to open it I get a message saying: Please insert the SD card. When I go to Device Manager and disable and enable fine orks. I tried different cards, but it makes no difference.
  I installed a different card reader, but another did the same thing. This leads me to think it's a matter of Windows.
  I tried to do a repair install, but it ends and said that the upgrade has failed?
  Anyone have any ideas on how to solve this problem.

  I am running Windows 7 Pro 64-bit. It is a Renesas controller and I use the 2.1.28.0 with firmware driver 4015.

  I'm not sure but I may have found the problem. I see where a guy here was having a similar problem and it was caused by Acronis. I recently installed Acronis 2012. I have been lucky to uninstall, but I will update this post when I do.  He was also running windows 7-64 bit on a motherboard ASUS!

  Acronis was the problem.  I uninstalled Acronis and now my card reader works as it should.  Strange!

• CD/DVD drive appears in Device Manager.

  Original title: my cd/dvd driver is missing from my device manager.  How can I get that back. I have a pavilion dv9700 and windows vista.

  my dvd/cd driver is not found in my device manager.  How can I get that back. I have a pavilion dv9700 and windows vista. I don't know what happened, but my laptop is useless now.  I have also run out of space in the drive d and f.  It's a little more overwhelming since I don't have much in my laptop.

  Hello

  You can run the fix it try the manual steps in the link below to fix the problem.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

• USB and DVD not recognize anything it shows that peripheral unknown.

  Original title: USD/DVD does not work.

  my USB and DVD does not recognize anything, it shows device unknown and does not work.

  Hi alexandrebernat,

  You did it all change hardware or software on your computer before this problem?

  For the question USB, you can follow this link & check if it helps.

  USB port may stop working after you remove or insert a USB device

  Reference: Troubleshooting tips advanced to General problems USB in Windows XP

  For the CD/DVD drive problem, you can follow this & check if it helps.

  Your CD or DVD drive cannot read or write media

  Reference: How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD

  Hope the helps of information.
  Please post back and we do know.

• 1 t verbatim USB stick not recognized by the system and will not work

  I used my USB from Verbatim 1 t hard drive in the past and it still works on my Vista computer, but know is is a USB 'unrecognized' device and does not work on my XP.  In the system hardware listing is visible, but there is no driver for it and not available from my computer.  This disc is missing?  How can I get this, my backup disk, of the function?

  Hello

  Try the steps of troubleshooting mentioned in the links below and check if the problem persists.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Note:

  BIOS change / additional settings CMOS (semiconductor) to oxide of metal bad cancause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Why my computer does not detect my new USB device when I run Windows XP or Windows Server 2003?

  http://support.Microsoft.com/kb/314634

  Note:

  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://support.Microsoft.com/kb/322756

  How to back up and restore the registry in Windows

• Realtek card gives the error code 10 and does not work since the change of satellite

  How can I fix the realtek on my computer card. It was the dial upwards, after he took off and replace it with satellite my computer wouldn't access internet
   
  How can I fix the realtek on my computer card. He has been on dial-up, after taking if off dial-up and replaceing with satellite my computer wouldn't access internet. Noted code 10 and realtek does not work. So a please help fix me my computer.

  Hello

  What operating system is installed on the computer?

  The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  See the following article:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

• my vista crashed and I tried to reinstall, but get an error message "do not all installation media."

  I tried to reinstall after a crash. I reormatted the car and tried to reinstall, but get an error message it doesn't recognize any media. I did a format on the page that appears at the facility and tried to "Refresh" and tried several times. I tried two different drives, including one of the vista did before.

  Hello
   
  How you try to install Windows Vista?
  
  Follow the lin below and check if it helps you.
  
  Installation media may not be recognized when you try to install Windows Vista from the CD or the DVD
  http://support.Microsoft.com/kb/928633

• This cable or accessory is not certified and may not work reliably with this iPad.

  I get the following message: "this cable or accessory is not certified and may not work reliably with this iPad." Oh, and the message repeats every so often. At first, I thought maybe would it be the earbuds, but I get the message, even though no headphones are attached. I get the message when no cable is attached. This occurs even if no cable is fixed. A hypothesis as to what is happening there?

  < re-titled by host >

  These alerts can appear for several reasons: the cable is defective, damaged or may not be certified by Apple, or your device might have an accumulation of dirt or damage. Follow these steps:

  Before you try the following steps, make sure that the USB cable and your port is clean!

  1. Restart your iOS device.
  2. Try a different cable certified by Apple or a charger.
  3. Make sure you have the latest version of iOS.
  4. Contact Apple support to implement the service.

  I hope that you will charge your iPad in no time!

• Xbox 360 wired controller works only with Windows 8. Xbox 360 Assecories status when I click on it says I have it has been changed or moved, and will not work.

  I have a controller wired xbox 360, not one of these pieces of plug. I put the USB controller and installed the device. However, it does not work. Xbox 360 Assecories status when I click on it says I have it has been changed or moved, and will not work. I have not touched. When I search for a download for Windows 8 all get them are downloads for Windows 7 and below. It's a bit frustrating to not be able to use it. I would be very happy to help.

  Original title: windows 8 wired 360 controller

  I found the problem. I had the appropriate controller and installed the device correctly. This is the program that runs the unit that had either corrupt or missing files. I uninstalled the program and then installed from the Microsoft Download page. Now he works currently. Thanks for the support.

• NDAS services stopped and do not work after installing Windows 8

  Ladies and gentlemen,

  My Services of NDAS stopped and do not work after installing Windows 8. This is necessary to run my SUNGOO LAN hard drive.

  Does sb know what to do?

  Best regards, Rolf

  Hello

  If I understand correctly the NDAS (Network Direct Attached Storage) service has stopped working after the installation of Windows 8. Is this correct?

  Please provide additional information for a better understanding of the issue.

  1 are you faced with the question of the NDAS service on the computer having the hard disk SUNGOO?

  2. how many computers using the hard disk on LAN?

  Specify the computers with Windows 8.

  3 are the computers in a home group?

  Please post the information requested to receive specific troubleshooting steps.

  Other links

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/NDAs-error-wont-see-drive-after-Win7-install/a004b2a3-9dd4-48a1-9ce7-c289931ba17b

  Why Windows is not find my device?

  http://Windows.Microsoft.com/en-us/Windows-8/why-isn ' t-windows-conclusion-device

  I hope this helps.

• Is it possible to uninstall McAfree branch of vmware Fusion once installed?  My D: drive shows McAfree lnsigna and will NOT work?

  Is there anyway to uninstall vmware Fusion installed security McAfree?  My D: drive has lnsigna it McAfree and does NOT work?

  Is it possible to uninstall McAfree branch of vmware Fusion once installed?

  I'll assume that your question is in fact to return to the physical optical drive (rather than the image of McAfee), does not actually uninstall McAfee.

  Right click on the D: drive and eject it. Then go to the Virtual Machine > CD/DVD and select use physical disk drive. It is documented in the release notes to the title of "The rest McAfee antivirus ISO mounted".

• As I installed Sierra, my Trusteer account to my Bank quit and does not work when I reinstall. Neither will Quickbooks!

  As I installed Sierra, my Trusteer account to my Bank quit and does not work when I reinstall. Neither will Quickbooks! Help!

  Trusteer (report) has caused a lot of problems Mac users such noted search Apple Support communities here.