change of access port blocking another port

Similar Questions

• Change the listening port for SSH on IDS

  Should what command I use to change the listening port on an IDS 4200 series? I listen on another port, and when I applied the S189/S190 update, it changed SSH port 22.

  Just out of curiosity, too, no one knows what else S189/S190 updates change?

  Thank you

  Jim

  Cisco supports only configurations using the CLI interface. The ssh port cannot be changed through the CLI. Modifying the files in config system via the service account is not a good idea and not supported.

• Change the default ports for http and https

  Hello

  I'm trying to change the default ports for http and https

  I have a 506th PIX (which does NOT of NAT)

  I have the following: -.

  static (inside, outside) tcp 192.168.10.2 601 192.168.10.2 http netmask 255.255.255.255 0 0

  static (inside, outside) tcp 192.168.10.2 602 192.168.10.2 443 netmask 255.255.255.255 0 0

  access-list acl permit tcp any 192.168.10.2 eq 601

  access-list acl permit tcp any 192.168.10.2 eq 602

  Access-group acl in interface outside

  where 601 and 602 are the http port and https to be redirect to respectively.

  I changed the webserver accordingly

  I get the error message

  "No group of translation not found for tcp src outside:189.x.x.x/50232 dst inside:192.x.x.x/80" (trying to access port 80)

  "I also have ' fixup protocol http 601.

  I had access to the internal and external web server before attempting to change the default ports

  Any ideas where I'm wrong?

  See you soon.

  I apologise for not thinking correctly.

  the static method must be:

  static (inside, outside) tcp 192.168.10.2 80 192.168.10.2 601 netmask 255.255.255.255 0 0

  static (inside, outside) 192.168.10.2 tcp 443 192.168.10.2 602 netmask 255.255.255.255 0 0

• Change the default port

  Can someone point me to a document that describes the steps to change the default port (8080) to another port on an existing Foglight environment?

  The Foglight Management Server (FMS) port is configured in FMSHOME/config/server.config:

  # These options are required, they must be configured for the server starts

  #

  Server.http.port = "8080";

  Server.HTTPS.port = "8443";

  You can change them by modifying the config file and restart the FMS.

  BUT:

  Remember that all Management Agent Foglight (FglAMs) use this port to send data to the FMS.

  Foglight users may have bookmarked FMS URLs with the original port number.

  Under Unix, a process must have permissions root a low numbered path (if you thought to change port 80)

  To make the seemless transition, you should consider implementing some sort of system (for example with an Apache web server) port forwarding so that agents and users who use the original port will not break.

  Kind regards

  Brian Wheeldon

• How to change the infrared port on Satellite M30 to be IrDA to be direct IR?

  Hello world

  I just bought a new watch that should be able to communicate with a pc via the infrared port (it's the Polar S710).
  Unfortunately, it does not work as the 'Protocol' of the watch is directIR, rather than be IrDA, as is my cell phone.

  I saw somewhere that it would be possible to change the infrared port of my laptop in order to operate in directIR. Anyone know the procedure? I think I could change something directly in the driver, but I did not how to deal with.

  I would be very grateful if someone could help me.

  Thank you
  SEB

  Hello

  I think that it of not possible to change the IrDA Protocol on the laptop.
  But have you tried to update the software polar?
  Consult the manufacturing site:
  http://support.polar.fi/PKBSupport.nsf/library?OpenForm

  If this does not help I think that only and an external solution as USB-> DirectIR dongle help

• change the com port assigned to the fax and scan

  I used fax and scanning for once.  I had to move my external modem to a different port.

  I don't know how to change the windows fax and scan com port manually.

  the wizard does NOT start, I guess because the fax is installed and worked until I had to change the number of COM port...  I need to change the number of pot with hundreds of research, it seems that no one knows how to change manually the Compote in windows fax and scan, unless they use the wizard.

  my assistant does not start. I guess I'm 'old school' I don't need an Assistant, I need to manually change the fax uses com port.

  :-), it's frustrating because help said only: click "fax" in the lower left corner, and they all assume the installation wizard starts and everything will be fine. :-(

  the wizard does not start. :-(

  I am desperate to get my fax work and need to know how to set the correct port number in a system that is installed and running, such as the wizard never starts.

  for anyone who goes out at the end of questions and ideas, I have a fax application stand alone who is working with the new port setting. It's just not a good app for my needs

  Please?

  Thank you

  John

  Post proposed by the moderator of the appropriate forum category

  Hi John,.

  You can follow the steps below to change the COM port for a modem:

  1. search the Device Manager.

  2 look for the Modem device, right-click on it, and then click Properties.

  • If the change settings button is present, you must click on it to make changes to the appliance. If the user account control dialog box appears, confirm that the displayed action corresponds to what you want, and then click continue.
  • If the change settings button is not present, the modem does not support the ability to change the modem settings. Refer to the documentation provided by the vendor of your modem.

  3. on the Advanced tab, click Advanced port settings.

  • If this option is not displayed, the modem does not support the ability to change the assigned COM port. Refer to the documentation provided by the vendor of your modem.

  If the same persists, we suggest that you post your query in Microsoft TechNet so that their support team will provide you in-depth assistance.

  Kind regards.

• Where can I find the ability to change the com port settings in Windows 7

  Where can I find the ability to change the com port settings in Windows 7

  Port, Device Manager, select comport, right click, properties, Port settings

• Compare Dot1Q and QinQ with access ports and trunk?

  Hi all

  How do you compare Dot1Q and QinQ with access ports and trunk?

  Thank you

  Sunil Kumar

  Hey, Sunil,.

  With regard to your questions:

  1. we have a case of Dot1Q configured on the port of access of habit?  If not, then why? - Dot1q aims to tag executives leaving the switch and access is opposite, it does not therefore not used together marking.

  2. how the topology would be for QinQ case? - For QinQ as I mentioned in my last post one side will be set to while links to access than others. A simple example is explained on this link:http://networklessons.com/switching/802-1q-tunneling-q-q-configuration-example/

  HTH.

  Kind regards

  RS.

• Highway X8.2.2, Changing default SIP Port for B2B calls is not possible

  Much of community support.

  I 10.5.1 (SU1) of CUCM and X8.2.2 Expressway.

  I have configured without VPN Jabber and B2B based on the Document calls "CVD-CollabEdgeUsingBE6000 - Apr14.pdf.

  everything worked fine for months, but after the upgrade of the X8.2.2 Express way B2B calls are no more work.

  After troubleshooting, I found the following:

  the DSF Guide tells me to change the default Port to 5061 to 5560 B2B calls because 5061 is also used for the integration of Jabber.

  When I look at my record of wirekshark I see cucm tries to connect to the port 5560 expressway, but after sending a SYN packet, cucm receives a RST packet.

  When I change back to the port of 5560 to 5061, everything works well again for B2B, but of course encrypted calls Jabber connection is not possible more.

  for me, it looks like a bug, but I found nothing on the 'Bug search' tool.

  I also tried to disable all Protection rules and I also have a firewall rule for Port 5560. I also tried to change the TCP Port to something different, 3999 for example. All this without success.

  Just a little look in the guide.

  Two caveats. First thing the guide explains unencrypted SIP - TCP connections, if you want to be aware that both sides use TCP or TLS. If you are using TLS certificates must be good as well.

  5560 isn't a port on the highway, this is the port for the trunk on CUCM.

  What do you see CUCM sending to Highway: 5560 Setup is not ok.

  The port of the highway will not be changed.

  If you look at page 30, he 5560 port is used for the "incoming Port *" and the bottom of page 31

  You can see that it uses the Expressway IP with port 5060.

  On the highway, you configure the area to port 5560 (page 34)

  And of course the firewall should also be ok.

  Please note messages posted under the stars below and set the thread if it's an answer!

• How to change the rmi port in atg

  Hi guys,.

  How to change the rmi port in atg

  who is the component to change port rmi in atg?

  The rmi port is defined in the component/atg/dynamo/Configuration. so in this Configuration.properties, you can change the value of the rmi port.

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• Change the listening port

  I am running Oracle 10.2 on Solaris. I want to change the listening port of 1521 to 2690. I've read that I'm supposed to change /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora and restart the receiver. Here's my listener.ora:
  
  OPENVIEWLISTENER =
  (DESCRIPTION =
  (ADDRESS_LIST =
  ((ADDRESS = (PROTOCOL = tcp (PORT = 2690))(HOST=flare)))
  SID_LIST_OPENVIEWLISTENER =
  (SID_LIST =
  (SID_DESC =
  (GLOBAL_DBNAME = openview)
  (ORACLE_HOME=/opt/oracle/product/10.2.0/db_1)
  (SID_NAME = OpenView))
  )
  
  
  After the reboot, it is still the 1521:
  
  bash-beginning of lsnrctl $ 3.00
  
  LSNRCTL for Solaris: Version 10.2.0.1.0 - Production on 24-AUG-2008 16:53:33
  
  Copyright (c) 1991, 2005, Oracle. All rights reserved.
  
  From /opt/oracle/product/10.2.0/db_1/bin/tnslsnr: Please wait...
  
  TNSLSNR for Solaris: Version 10.2.0.1.0 - Production
  System settings file is /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora
  Log messages written to /opt/oracle/product/10.2.0/db_1/network/log/listener.log
  Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))
  
  Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))
  STATUS of the LISTENER
  -----
  Alias LISTENER
  For Solaris TNSLSNR version: Version 10.2.0.1.0 - Production
  Departure date 24-AUG-2008 16:53:34
  Uptime 0 days 0 h 0 min 0 sec
  Draw level off
  Security ON: OS Local Authentication
  SNMP OFF
  Parameter Listener of the /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora file
  The listener log file /opt/Oracle/product/10.2.0/Db_1/network/log/listener.log
  Summary of endpoints listening...
  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))
  The listener supports no services
  The command completed successfully
  
  What I am doing wrong? :(
  
  

  user527462 wrote:
  I am running Oracle 10.2 on Solaris. I want to change the listening port of 1521 to 2690. I've read that I'm supposed to change /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora and restart the receiver. Here's my listener.ora:

  OPENVIEWLISTENER =
  (DESCRIPTION =
  (ADDRESS_LIST =
  ((ADDRESS = (PROTOCOL = tcp (PORT = 2690))(HOST=flare)))
  SID_LIST_OPENVIEWLISTENER =
  (SID_LIST =
  (SID_DESC =
  (GLOBAL_DBNAME = openview)
  (ORACLE_HOME=/opt/oracle/product/10.2.0/db_1)
  (SID_NAME = OpenView))
  )

  After the reboot, it is still the 1521:

  bash-beginning of lsnrctl $ 3.00

  LSNRCTL for Solaris: Version 10.2.0.1.0 - Production on 24-AUG-2008 16:53:33

  Copyright (c) 1991, 2005, Oracle. All rights reserved.

  From /opt/oracle/product/10.2.0/db_1/bin/tnslsnr: Please wait...

  TNSLSNR for Solaris: Version 10.2.0.1.0 - Production
  System settings file is /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora
  Log messages written to /opt/oracle/product/10.2.0/db_1/network/log/listener.log
  Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))

  Connection to (ADDRESS = (PROTOCOL = tcp)(HOST=) (PORT = 1521))
  STATUS of the LISTENER
  -----
  Alias LISTENER
  For Solaris TNSLSNR version: Version 10.2.0.1.0 - Production
  Departure date 24-AUG-2008 16:53:34
  Uptime 0 days 0 h 0 min 0 sec
  Draw level off
  Security ON: OS Local Authentication
  SNMP OFF
  Parameter Listener of the /opt/oracle/product/10.2.0/db_1/network/admin/listener.ora file
  The listener log file /opt/Oracle/product/10.2.0/Db_1/network/log/listener.log
  Summary of endpoints listening...
  (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp)(HOST=flare.halcyoninc.com) (PORT = 1521)))
  The listener supports no services
  The command completed successfully

  What I am doing wrong? :(

  Your listener.ora sets a listener named OPENVIEWLISTENER. You have not specified the name of the listener when starting it and so he went with the default values (name of the LISTENER listener and so on). The command you are looking for is lsnrctl start OPENVIEWLISTENER

  concerning

  Niall Litchfield
  http://www.orawin.info/

• Could not get Outlook Express to send a copy to my server, so I can access it from another computer

  I can not Outlook Express to send a copy of my e-mail messages to my server (Charter.net) so I can access it from another computer.  I tried to check the block that says "Send copy to the server", but that did not work.  Any suggestions?  I'm not a true computer person so that the answers should be very details.  Thank you.

  The messages on your computer now, you would have to back to yourself, and then they would be on the server.  For the future, go to tools | Accounts | Mail | Properties | Advanced and check the leave a copy of messages on the server.  Do it with another machine in order to get the messages on both machines.  Then also set one of them to delete messages from the server after a few days, so that they accumulate and fill the mailbox you.

  Steve

• Folders of bookmarks in Safari in the Favorites bar not open click when you access one after another

  Question: The records of Safari bookmarks in the bookmarks bar not open click when you access one after another

  Diagnostic steps:

  (1) create 2 or more folders in the bookmarks with the individual sites in their breast.  (Examples of folder name: career, finances and health)

  (2) safari > display > display favorite bar. All the Favorites should be visible in the main window of Safari with all these files

  3) click on the folder named career and then go directly to Finance. (the record finance should open with a single click)

  (4) or try to open the folder of health directly after clicking on career record. The health record is expected to open in one click. This does not currently happen

  Currently, 2 click are required to open a folder in the Favorites bar. To activate the button and the second displays the Web sites it contains.

  It is annoying and seems as if the browser is obsolete.

  If opening cursor hover is not what apple wants for these records, we are fine with it. But the least we should do, it's that these files opens in one click.

  Thank you.

  Send feedback to Apple. They will not respond, but at least know that there is a problem. If enough people send feedback, it can become the problem solved as soon as possible.

  Your comments

• Why can't access to blocked senders list or add?

  I can't access to blocked senders list or add.

  For all have a problem with Hotmail, please ask the experts in the Hotmail forum. Many of us do not use this application and cannot help.

  Windows Live Solution Center Hotmail Forum
  http://windowslivehelp.com/forums.aspx?ProductID=1