Channel configuration of the individual on a CCS system

Similar Questions

• Configuration of the individual channels on the PXI-4472 b

  Hi, I use the card PXI-4472 b to acquire data of vibration using sensors with different frequency ranges. The problem I have is that some of the transducers require being fed by the jury (via IEPE) and some don't and I can't find a way to turn the excitement on and off for individual channels, only each other.

  I am using LabVIEW 8.6 and that you have configured all channels using the nodes property to activate the excitement and specify the current, but not all channels require that.

  It says clearly in the data sheet of the map of 4472 channels are individually configurable for the IEPE, can someone please tell me how to proceed?

  Thanks in advance,

  Darren.

  Howdy Darren,

  Please see the following screenshot that illustrates how to set different values for different channels of IEPE all in a single task using DAQmx. The key point here is the property of ActiveChans. Otherwise, as you know, 3GEF55NQ knowledge base: How can I activate IEPE excitement on my DSA in DAQmx device? would do the trick.

  

  I hope this helps!

• Configuration of the XBR-65x850c channels - I put the type of signal to the 'cable', but he always comes back to the "antenna".

  I have the TV signal by cable from the TV directly to the output - without cable box.

  Under 'Configuration of the strings' / 'Type of Signal' I choose "cable."

  The works of TV and I watch cable TV.

  I'll be back later in the day and the parameter 'Type of Signal' has changed to 'antenna' and I can see is more channels.

  I change it back and it works until the next time I try to watch TV when I find that it has changed again.

  Someone knows how to keep permanently the setting on "cable"?

  Thank you!

  This problem has been fixed with a recent update.

• How can I change the configuration for the output channels analog on a PXI-6704?

  I can't seem to understand how to access the configuration of the channels to the outputs analog (channel 33 and 35) for PXI-6704.

  This piece of test equipment is out of tolerance and must be calibrated.

  I have followed the procedure of calibration http://www.ni.com/pdf/manuals/374081b.pdf, but am getting hung up on step 8, where it is said to repeat steps 4-7 when changing the _cal_ao_current_offset. I can't figure out how to open this channel because it is not listed as a physical channel for step 5.

  I'm using Labview 7.1

  Thank you

  Hello! What you need to do is to add 'Internal channels' to your list of channels, so you can choose the _cal_ao_current_offset or _cal_ao_voltage_offset.  This is done through the drop-down list channel right click and select "I/o name of screening...". ».  There will be a check box that says 'Internal channels' and will provide you with all available internal channels to enter your vi Create Channel.  I have attached some photos illustrating how to do. See you soon!

• Configuration of the channel of port on nexus 1000V

  Hello

  I'm new on nexus 1000V, the configuration is as follows, UCS chassis with 4 blades full-width connected to 2 FI 6248UP.

  each FI's uplink to a n5k (no mail ORDER).

  is there any configuration model the nexus 1000v? How to configure port-channel?

  Thank you.

  Hello

  We recommend using mac pinning ("channel-group auto mode on mac - pinning") when N1KV is used on the blades of the UCS.

  Next doc provides good overview on best practices.

  Best practices in deploying Cisco Nexus 1000V switches in the Cisco UCS B and C series series Cisco UCS Manager servers

  http://www.Cisco.com/en/us/prod/collateral/switches/ps9441/ps9902/white_paper_c11-558242.html

  HTH

  Padma

• Configuration of the audio channels in PP 2015.3 v10

  Hello

  I noticed that the path of the Audio track has changed to the Configuration of the Audio channels in the settings of export of the latest PP. Unfortunately, this affects the way in which players such as QuickTime read the layout of the audio channel.

  For example, I went out a DNxHD MOV video with 24 channels for a customer. I attributed to them in my PP of the project and am ready to the output file. The previous version of PP has allowed you to assign titles in the drop-down menu, the Audio track route which, in turn, allowed to see each audio channel / stem in the movie in QuickTime player Properties menu option.

  Unfortunately, in the last version of 2015.3, my final file of DNxHD output has all channels play off the one audio track when opens in QuickTime player. However, I don't see all the audio stems when I reimport the DNxHD PP file so I think that this only affects the software outside Adobe.

  I wouldn't mind not so much, but the customer would like to see the audio presentation in QuickTime player, so I'm a little confused as to what is wrong here with the last update PP.

  Why this changed in the first place? Any help will be very appreciated!

  Concerning

  Tony

  System specifications:

  Premiere Pro 2015.3

  Windows PC 10, 16 GB of RAM

  So, I thought about it fortunately! So you have to choose Audio MONO Channel Configuration settings and then add as many channels as you need (for me it would be 24 mono tracks). As long as you properly assigned audio channels of your sequence, then the output file should be fine.

  This seems a strange and unnecessary change for me - I don't know Adobe not have their reasons, but that would have saved me some valuable time if we have correctly explained in the update notes!

• Configuration of the tough thresholds on individual resources

  Hello

  Last week I did a vC presentation Ops at one of our clients. One of their questions were so hard thresholds configuration worked on individual resources and not on a whole resource type?

  For example if I want to put a threshold hard on only 1 VM which is in need for an ATH determined dynamic thresholds and other hard thresholds VMs.

  

  Customers thought it was strange, if this configuration has been performed worldwide to all resources within a resource type. Am wrong me or is this the case when it comes to hard thresholds in vC Ops 5.8?

  See you soon,.

  Erik Alm

  No change to 5.8 here. You have to keep in perspective that you edit the package "attribute" in the screen that you attached here... not clear the global setting for each type of resource. If you want to set a different specific resource, simply create an attribute different package and assign it to this resource.

• LR4.1 - tone curve - how to set the individual RGB channels?

  Hello

  I can't find out how to set the curve of different RGB channels.  I guess the LR4 tone curve works as the dialog box curves PS with the channel drop-down list.

  LR4.1 help says:

  To make adjustments at different points on the tone curve, choose an option in the menu of the curve of points, click the button change the curve of points , and then do one of the following:

  • Choose an option from the popup menu of the channel. You can change the three channels at once, or choose to change the red, green, or blue channel individually.

  When I click on the small icon in the lower right corner of the Panel curve tones, the Panel shrinks while I do not see the sliders of regions.  If I click again, they are visible again.  I can't find where to select one of the three channels indvidual.

  Aid refers to the "Point curve menu."  Where is the menu Point curve?  The curve of points is different from the tone curve?

  If I right-click (Windows) in the curve dialog box, the shortcut menu has an option show information.  I click on it power and don't see any change or any info.  Where should I look for info?
  

  Thanks for any help here.

  John

  
  

  Hi John,.

  The curve of points is without cursors. The settings for the individual channels are only available with

  PV2012. You must be editing a file with PV2010 or 2003. When to PV2012, you will see "channels: RGB" under the window of the curve. Click on the triangles of doule following RGB

  for each channel.

  HTH

  Rich

• Internal Server Oracle 11 g b2b JMS Configuration of the delivery channel

  Hello
  
  I'm using Oracle 11 g b2b server is configured with the Protocol of Mae. I created an internal delivery of JMS to host business partner channel. Now the message inbound (remote trading partner message) is given to dorsal application via the internal delivery of jms channel. Now, I wanted to send you this message to the domain of the weblogic another server that is hosted on another box. So where can I give the other weblogic domain details such as the message will be delivered from the host commercial b2b serveur_partenaire to the weblogic domain queue remote?
  
  Kind regards
  Belleau

  Hi Ben,

  As already mentioned by Nitesh, you can create a channel of internal delivery of JMS and even configure in your agreement for routing messages to the remote (domain) weblogic JMS queue.

  Details of port and the ip address of the remote weblogic domain can be configured as part of the JMS internal delivery, 'Provider of Destination' channel, as below,

  for example.
  Java.naming.Provider.URL=T3://:; java.naming.factory.initial = weblogic.jndi.WLInitialContextFactory; java.naming.security.principal =; java.naming.security.credentials =

  In this case, messages delivered directly to remote JMS queue.
  Concerning
  Nebot

• Several Airport Apple ID devices disappear shared devices and Software Configuration of the airport

  We have three Airport extreme and two Airport Express devices in two offices in the city.  Some time in the last two days, they all stopped appearing in the sidebar of Finder 'Shared' category (if they had attached disk storage) and they stopped from appearing in the Configuration software of the airport on any of the Mac on these networks. (They always seem to be correct, routing traffic, however).

  For a while, we left a desktop completely alone as a control group and did all our testing and troubleshooting in the other office.

  We-hard reset (to the factory configuration) all devices from the airport to an office. They began to appear again. Then we started to re - configure them again.  At the time wherever we had updated the devices they had disappeared again.

  So, another factory discount based configutations for each device to this facility. Then we added slowly in pieces of their configuration.  When airports have received Apple ID and associated passwords for associating with iCloud/BackToMyMac/WideAreaBonjour (depending on what you want to call it), the airport devices disappeared from the airport Setup.

  If we tried to configure another device from the airport to extend a network of 'invisible' airports, the new airports were "unable to find" one of these networks to expand.

  If we reset all devices without providing them with Apple ID and passwords, they worked mainly as you would expect. The main difference being now do not appear as having been recorded as BackToMyMac/WideAreaBonjour devices.

  One side for people dealing with this note: If your router are invisible, but they are configured to be configured from the EXTENSIVE worldwide network, you can use "File-> configure the other" and specify the address WAN of the missing aircraft and get this screen access as one would generally. From here, remove all the Apple ID associated with these devices, press "Refresh" to save the settings and they seem to reappear magically in the Configuration of the airport software.

  In that State, storage seems to be available, but only for devices in Domain Local (direct connection). Airports without AppleIDs will not appear in the field to iCloud/BackToMyMac/WideAreaBonjour, and it's as expected, given that these IDS is the means for the identification of their field.

  If someone else has noted these behaviors and if so, have an idea about specifically when they first appeared? Is there by any chance someone who knows of any change in registration or the MWAC of multiplication?

  Did you approach the problem exactly as I did in the past, and having encountered problems of the CCMM literally every version of OS X. They were all distinct problems with individual characteristics, and in some cases the solutions exist. Having said that the CCMM has been completely reliable recently - which means running the most recent El Capitan release on all my Macs. The initial versions (i.e. OS X 10.11 to 10.11.3 maybe) didn't work at all. I don't know which version fixed whatever the problem was, I am sure he has not worked for someone else.

  The same real place with Yosemite and previous versions as well. CCMM did not reliable until the exit "point three or four."

  Through these experiments, I believe it should be a pretty fast connection. If the connection between a Mac and all the others does not meet this requirement (whatever that is) all you will be able to determine, it's that the CCMM fails.

  Apple is characteristically silent about the technical aspects of the CCMM, probably because of security concerns. Nobody outside Apple knows how it works. If you're still having problems, I encourage you to contact them. After mentioning predictable you corrective raw materials (the two following links) you will be put in touch with someone who will look to what is false, providing diagnostic assistance and send your information to engineering. If it's something they should fix, you'll know not to the point of an OS X update is published.

  Set up and use Back to My Mac - Apple Support

  Get help using Back to My Mac - Apple Support

  With all the conversations I had with Apple on this topic (which were many, involving a large amount of tests) not once they disclose any causal factors individual, other than to reiterate the need to run the last OS X, versions and the latest versions of firmware for their routers. In your case, that means probably that your Mac update to El Capitan. It is after all the very first recommendation in their document of support above, until you do this you will still not get in step 1.

• How can I get multi channel audio via the HDMI port on an early 2015 MacBook Pro?

  I try to get the 7.1 audio channels to flow from my MacBook Pro to a cinema set up. The display works fine now I plug the HDMI in however the sound still Mac speakers. I checked the settings and no HDMI output is available. An airtime option is available, but that returns only two channels as a maximum to the receiver. When I go to the configuration of the source on the receiver it receives video at 1080 p 60herts however it is specifically stated No Audio from the Source.

  Also, I have connected my iPhone 6 s more using an Apple through the same HDMI cable adapter and it works perfectly. We also use HDMI with our PS4 occasionally and it works perfectly, even with the 3D.

  Thus, the MacBook Pro is early 2015 with an i5, the receiver is a Harmon Kardon AVR 2700 (we run 7.1 channels of this) and we are connecting via the HDMI port through a 50 ft HDMI before. The receiver sends the audio to a projector with 1080 p 60 hertz if it changes anything...

  Also if it helps the receiver supports dts - hd master audio decoding, Dolby True HD/Digital Plus decoding, HDMI 1.4 (HDMI is compatible 2.0), as well as multi-channel input and PCM and linear PCM.

  I use a "Behringer UCA202' audio device I bought on amazon.com for only $29.

  It works very well for the audio 5.1 or 7.2. Works connect optical toslink. Just plug it into a usb port on your Mac and a cable optical toslink to your AV receiver.

  My Yahmaha 7.2 audio/video receiver is measuring process the digital signal in THX, DTS, Dolby digital Pro logic, a cinema, etc.

  

• change of scale of a channel running from the DAQmxSetScaleAttribute task

  Hi all

  simple system configuration: AI channel is configured using OR max and also using a scale that is configured in NI Max.

  Once the system is running, the task of the program started and playback of data acquisition, everything's fine. now I want to do is get the value of a string and reading that the DAQmx reads on the channel by chaning the ordinate at the origin of the linear scale at zero. I tried to get the y-intercept value and the actual value of the existing interception and defining the DAQmxSetScaleAttribute with the new linear value and nothing changes on the sudtracting channel. Possible solutions, I tried shutting down and restarting the task but not clearing and reloading of the task.

  I also tried DAQmxSaveScale, but the value in NImax for interception does not change either.

  is it somehting in the order of calls which must happen, or I can even change the scale on a task without compensation or recharge it the task?

  OK, that's how I got it working again noted that the system is configured using NImax and all the channels to HAVE are in a single task, also an important feature is that I use the DAQmxRegisterEveryNSamplesEvent function. each channel also has its own scale.

  First you need to find is the next shift, you need to recalcualte the max and min to the beach of this channel and save everthing.

  DAQmxGetScaleAttribute ("1Dist", DAQmx_Scale_Lin_YIntercept, & readOffset);  \\get the existing scale value
  stopDAQ();
  GetCtrlAttribute (panelManual, MANUAL_1POS, ATTR_CTRL_VAL, & actualReading);   \\reading off the coast of data acquisition
  newOffset = (actualReading + readOffset) *-1;                                                                     offset \\calcualte
  ERR is DAQmxGetChanAttribute (gDAQTaskHandleAI, "1_Unit_Ext_Pos", DAQmx_AI_Max, & max, NULL);.   cahnnel \\get NIMAX Info
  ERR is DAQmxGetChanAttribute (gDAQTaskHandleAI, "1_Unit_Ext_Pos", DAQmx_AI_Min, & min, NULL);.      cahnnel \\get NIMAX Info
  newMax = max + newOffset;
  Max = newMax;                  ------It will be ediedited what I did was made max an int to get rid of the decimal points
  newMin = min + newOffset;
  min = newMin;                   ------It will be ediedited what I did was made max an int to get rid of the decimal points
              
  DAQmxClearTask (gDAQTaskHandleAI);                                 \\clear the task due to the attached DAQmxRegisterEveryNSamplesEvent will thow errors because it is attached to the task
  DAQmxLoadTask (DAQMX_TASK_TITLE_AI & gDAQTaskHandleAI);
              
  ERR = DAQmxSetScaleAttribute ("1_Act_Ext_Dist", DAQmx_Scale_Lin_YIntercept, newOffset);
  ERR = DAQmxSaveScale ("1_Act_Ext_Dist", "1_Act_Ext_Dist", "", DAQmx_Val_Save_Overwrite |) DAQmx_Val_Save_AllowInteractiveEditing | DAQmx_Val_Save_AllowInteractiveDeletion);
  ERR = DAQmxSetChanAttribute (gDAQTaskHandleAI, "1_Unit_Ext_Pos", DAQmx_AI_Max, max, NULL);
  ERR = DAQmxSetChanAttribute (gDAQTaskHandleAI, "1_Unit_Ext_Pos", DAQmx_AI_Min, min, NULL);
          
  ERR = DAQmxSaveTask (gDAQTaskHandleAI, DAQMX_TASK_TITLE_AI, ' ',)
  DAQmx_Val_Save_Overwrite | DAQmx_Val_Save_AllowInteractiveEditing | DAQmx_Val_Save_AllowInteractiveDeletion);
  DAQmxClearTask (gDAQTaskHandleAI);
  DAQmxLoadTask (DAQMX_TASK_TITLE_AI & gDAQTaskHandleAI);
  GetCtrlAttribute (panelDAQ, DAQ_PANEL_SampPerChannel, ATTR_CTRL_VAL, & sampsPerChan);

  DAQmxRegisterEveryNSamplesEvent(gDAQTaskHandleAI,DAQmx_Val_Acquired_Into_Buffer,sampsPerChan,0,EveryNSamplesCallback,);

  startDAQ();

• Configuration of the analog triggers on NI9234

  I am writing a custom software that interacts with a NI 9234 scanning module, using the NiDAQmx C library.  I tried to configure unity with a trigger of analog edge on one of the channels.

  I use DAQmxCfgAnlgEdgeStartTrig() to configure the trigger, and it returned without error.  However, when I try to call DAQmxStartTask(), it returns with the error "attempted to use an invalid trigger analog source.  Ensure that the source of command, you specify is the name of the virtual channel in the task or is the name of a non readable terminal that the device can use as a source of analog trigger. »

  I have set up the channel by using DAQmxCreateAIVoltageChan().  I tried the two nameToAssignToChannel of parameter null to use hardware channel name and assigning the channel a different virtual name.  These two seem to work, as after the channel configuration that I can use DAQmxGetNthTaskChannel to see that the names have been configured correctly, but try to configure the trigger still does not work with the above error.

  I would appreciate any idea on this issue.

  Most of the Modules with 24-bit ADCs, have no trigger analog equipment.  You will need to implement an algorithm to trigger in the software (target RT, FPGA host)

• Best way to update the individual rows of a Table?

  I took a quick glance at a few examples, but did not get a clarification on this.  I am looking to have something close to a listbox control or the table to where I can update just one column of values to line a 1 time per second pace.  I'm looking to display our acquisition of data values in a table or a listbox control.  The single list box seemed to work well for that, but I couldn't use the row headers to list the names of channel beside the channel values.  I thought to link the values of cursor in two areas of list to do this, but did not find any info on it for the single list box.

  I have a few questions:

  (1) I have a 1 d table to where I want to use this data to constantly update the first column (with a multitude of lines) of a table.  I'm looking for the best route to not take too much time for treatment by doing this.

  What is the best way to update the individual rows of a table?   Invoke the node "Value of the cell value"... or is there another method?

  (2) why is that, after each iteration else, row values are deleted?

  Also, for adding additional channels originally arrray... it is better to use the 'Array' subset then the function "Construct the table" or function "Subset of the table" and "insert table"?

  See the attached example.

  Thank you.

  Jeff· Þ· Bohrer says:

  (2) why is that, after each iteration else, row values are deleted?

  Classic race condition.  dump the loop and node-p and just wire the 2D table on the terminal Board. !

  I don't see the race condition.  What I see is the table once the last element has been written for it all run the oil.  I saw looked it with point culminating performance on.

  But I agree entirely with writing to the Terminal.  It is a 1 d array, so you will need to use an array of generation and convert a 2D array in order so that he could write correctly.

• How do switch you between multiple channels to indicate which channel to acquire the data from?

  I'm trying to builld a VI where I can have an option to enable or DISABLE multiple channels depending on the modules plugged into the chassis and then acquires the data of the channels which are turned on and where other acquisition parameters do not change. Is there any specific/switch where can I do this? Please answer as soon as possible. Its quite urgent. Thank you

  You use DAQmx?  To change the assignment of the data acquisition channels, you must close the currently open session and then create a new session with the new channel definition.  So the order of execution:

  Create task or virtual channel - read - clear task of triggering and synchronization of the configuration - set new channel list and to create a task - read - clear task, etc...