.chm TOC using variables - print SSL does not recognize anything after the variable

Similar Questions

• One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. The location is the root (2 ports) USB hub: 1-unknown device and Port 2-not used

  Original title: USB device not recognized

  Over the last 2 weeks, I get a message on a USB device.  The message said that one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.  The location is the root (2 ports) USB hub: 1-unknown device and 2-unused Port.  I have no idea what it means.  I hesitated to first click the icon (it does not last very long) thinking it could be a scam.  Can someone help me?  Thank you.

  Hello

  (1) is the specific question of specific USB devices?
  (2) did you of recent changes to the computer before the show?
  (3) have you tried plugging the USB stick on another computer?

  (4) what is the brand and model of the computer?

  I suggest to refer to the following methods and check if it helps to solve the problem.

  Method 1: Hardware devices do not work or are not detected in Windows

  Run Microsoft Fixit mentioned in the article.

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: USB Port may stop working after you remove or insert a USB device

  http://support.Microsoft.com/kb/817900

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 How to back up and restore the registry in Windows

  Reference:--

  Advanced troubleshooting tips for General USB for Windows XP problems: http://support.microsoft.com/kb/310575

• Cannot add any material and my computer does not recognize one of the ports

  my computer won't recognize any port or plug and play devices. map of my camera not recognized when I insert in the port.my computer does not recognize one of the ports and if I try to download a driver for the printer, it starts and stops before installation. The computer had crashed and went blank. So I had to get a new hp boot disc and install it. Since then, it has happedned

  Hi gramward1,

  We recommend all first download and install the drivers for the chipset on the computer and check the difference.
  To download the driver, visit the website of the manufacturer of the system.

  Step 1: You can also try to search for the hardware changes and check if the device is detected on the computer. To do this, try the following steps:
  a. connect any USB device to the computer.
  b. Click Start, click Run, type devmgmt.msc, and then click ok.
  c. in the list of items, click one of the items, click the Action menu and click scan for hardware changes.
  d. check if the device is detected.

  Step 2: Try to remove and reinstall all USB controllers
  a. Click Start, click Run, type devmgmt.msc in the Open box and then click OK.
  b. in the list of components, expand Bus USB controllers.
  c. right-click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.
  d. restart the computer once you have removed all the USB controllers.
  Note: USB controllers automatically install after you restart the computer.
  e. plug the removable USB storage device and perform a test to ensure that the problem is solved.

  If the problem persists, run Microsoft he difficulty of this article: http://support.microsoft.com/kb/925196

  Visit our Microsoft answers feedback Forum and let us know what you think.

• When I try to start my computer, it does not load anything. The backlog, but the rest of it runs bad and slow. I can't open any programs that either, and my pointer always told it to load.

  Original title: Please HELP

  When I try to start my computer, it does not load anything. The backlog, but the rest of it runs bad and slow. I can't open any programs that either, and my pointer always told it to load. Safe mode works, but I just don't know what to do. Help, please

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Since it works fine in safe mode, I suggest you to try to perform the clean boot to safe mode and check if it helps:
  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  Method 2:
  Also, try to run the safe mode System File Checker and check if it helps:
  http://support.Microsoft.com/kb/929833

  Method 3:

  Be sure to run a full scan with your antivirus software.

  http://www.Microsoft.com/security/default.aspx

  It will be useful.

• iTunes on pc does not recognize my iphone. the pc does. the iphone asks me to allow access to what I do

  iTunes on pc does not recognize my iphone. the pc does. the iphone asks me to allow access to what I do

  Hello

  Check this help page: If iTunes does not your iPad, iPhone or iPod - Apple Support

• the printer port does not recognize hasp key

  I recently bought a Dell rebuilt to replace a running xp sp3 which had overheating problems with windows xp sp3.  I am running a previous software (7.5V2 friendly technology FlexiSign Pro) program that requires a hasp on a parallel port key.  I never had problems with the old computer recognizing the hasp key, but when I try to use this software on the new computer does not recognize the HASP.  I think what may be due to the fact that my new computer printer port is configured as instead of the lpt port ecp.  Is it possible that this could be my problem and I can change the port of older style? Any guidance is appreciated.

  Thank you

  Greg

  If the problem really is whether the parallel port in ECP mode, you can switch to EPP mode in the BIOS.  Restart the computer and keep a close eye at the beginning of the boot sequence for the message that tells you what key to press to enter the BIOS (change system settings or similar).  Restart again and press the key when the message is displayed.  You will have only a few seconds.

• Used to boot Windows - does not recognize the hard drive

  Hello. I had my computer laptop vostro dell for 5 years, and I've never had a problem. A few weeks ago, I was starting, and I got the blue screen of death. I had the same thing when I rebooted. I bought a SATA dock for recover my files, so I could format it and start from scratch. However, the dock does not detect my HARD drive, although I hear the disc running. I tried to connect a Dell Latitude docking station to transfer the files, but the Latitude does not recognize my HDD ether. Vostro runs XP Home Edition and Zorin OS, Latitude anime XP Pro. HHD in question is a 120 GB Western Digital Scorpio for drinking devices. Help, please.

  You boot from the disk and choose "Try without Unbuntu and change to your computer"?. Honestly, it looks that you have installed. In addition, using raid with Windows Xp support?

  If you have chosen to 'Try' Unbuntu I recommend now you run chkdsk /r from the recovery console. The problem is not with the hard drive probably, but with the file system.

  Download WIndows Xp Recovery Console from HERE. Save the file to your desktop. You will need to burn the iso image to a blank cd using the same way you did to the image ISO of Unbuntu ImgBurn. Although the instructions below refer to a Windows disk, the disk from the Recovery Console that you create will do the same.

  1. Insert the Windows XP CD in your CD-ROM drive and restart your computer. If you are prompted, select any options needed to start (boot) on the CD.
    
  2. when the text portion of Setup begins, follow the prompts. Select the repair or recovery option by pressing R.
    
  3. If you have a dual-boot or multiboot system, select the installation that you want to access from the Recovery Console.
    
  4. When you are prompted, type the administrator password. If you have not set a password for the account admin simply press on enter
    
  5. at the command prompt, type chkdsk/r > press ENTER. (Note: there is a space between the slash and the letter k).
    
  6. at the end of the output of scan type > press ENTER.
    
  7 restart your computer.

• Satellite M30X-111 screen does not display anything but the external monitor works

  My laptop just screen does not display anything (like when the computer is turned off), but when I connect the external monitor, then the desktop is displayed on this screen. I tried to recover the laptop using the recovery disk and it worked again, but today, it stopped working again.

  Again, I must plug the external monitor, and after I tried to restart, I continue to pressing F8 but the startup mode is not come, the noise of when you press a button for too long beeps, however, the monitor of the laptop working again.

  How can I solve this problem?

  What do you do? You want to recover the laptop?
  If Yes, you n press any F8 but you will need to boot from the recovery CD by pressing the C key immediately after starting the laptop.

  But this question seems that you have accidentally switched to external display.
  I recommend checking the Fn + F5 option. This combination allow you to switch between the display and the external monitor.

• Windows 7 password problem: does not recognize password after waking from sleep

  So I have recently buy a netbook with Windows 7 operating system. I create the administrator account and password protect. All right, install software, copy documents, etc. in the "My Documents" folder and happily use the machine for a few days with no problems. Then work off the battery voltage, put the PC in sleep for some time. When I try and log back in after the awakening of the PC, it does not recognize the password. Try with cap locks, off and all the rest, but not luck. I must finally remove the battery and restart. Sign in as normal (the password is recognized) and go in the user administrator account to disable the password, but then again, the current password is not recognized and I am not allowed to make changes. However, I can still close and log on by using the current password. Confused. Anyine have any ideas?

  There is no need to remove the battery or pull the taken when force a PC to stop. By pressing the power button for about ten seconds will do the trick.

  Your password problem: you might be dealing with a foreign keyboard problem. Make the password to something that is independent of the keyboard configuration, for example 123456.

  To reset the administrator password, follow these steps:
  1. click on start.
  2. type the three letters cmd in the search box.
  3. press on Ctrl + Shift + Enter
  4. click on "run as Administrator".
  5. type the following commands and press ENTER after each:
  net localgroup administrators
  (This will show you the accounts that have administrative privileges. What is?)
  NET user administrator 123456
  (This will set the password to 123456)

• My laptop does not do anything on the screen

  My laptop does not appear anything just blank black screen when I start my system

  Hello

  If nothing at all, not even a motherboard brand / model or Logo of laptop manufacturer is coming up on the screen when you turn on the power to the laptop, it seems to be a hardware problem.

  If under warranty, contact the manufacturer of your laptop.

  If it is not under warranty, contact a repair shop, local.

  See you soon.

• Creative cloud does not remember IDs after the computer restarts

  Creative cloud app does not remember login after restart of the computer, or simply when it starts after having turned it on. The app starts up fine and appears in the notification area (Windows 64-bit 10), but I have to log each time until I can get updates, etc. This problem started about 3 weeks ago and I still have to find a solution. Does anyone know how to fix this?

  In this case I advise you to Contact customer services as technical troubleshooting may be required.

• USB does not recognize anything

  I have a Toshiba A60-S1662. A USB port. The port has power, drivers are loaded, and it has a brand new XP Pro SP3 OS. The hub will not recognize anything I plug in there. I have assigned driver but refuses to play nice.

  It seems to me that it is hardware problem of your USB port.

  I downloaded the manual of your laptop and there is a slot of your laptop where you can insert "PC Card". PC card can contains the USB port.

  More information on PC Card:

  http://en.Wikipedia.org/wiki/PC_Card

  LC

• HP Laser Jet Pro M225dw MFP: HP E print App does not effectively bind to the Go Daddy email (HP Laser Jet Pro MFP M225dw)

  I bought a HP Laser Jet Pro (MFP M225dw) and am very excited about the mobile printing option. I downloaded the HP EPrint App on my smartphone (Samsung Note 4) and have successfully my gmail and hotmail accounts related.

  However, I have problems linking my Go Daddy account.

  As per a post on the forum of 2014, I have connected my Go Daddy via Outlook account, used the host name: imap.secureserver.net and Port: 143, SSL: WE. The account "seems" to link; However, when I click on my email Go Daddy Outlook icon, it brings back me permanently to the home screen, (the one that says "Photos, files, Web, Email") such that I'm never able to access really my Go Daddy email account.

  * No error message

  * Bluetooth off

  * 5.1.1 android

  * I have Norton Mobile on my phone

  * Looked at my Go Daddy security settings - no "two-step verification" or "allow the less trustworthy access apps to the ' questions

  Also, I see that this app is not able to print the body of an email; is there a way where information such as details such as email/recipient of the sender of transmission time, electronic mail may be included in the print job?

  Thanks a lot for your time and consideration!

  Hey @Lizaroo,

  Welcome to the Forums of HP Support!

  I see that you have some problems with your Go Daddy email account settings enter the HP ePrint app. For more assistance, your best option would be to contact Go Daddy directly to check all the parameters of the post that you found are correct. Some e-mail clients change their settings often so that I wouldn't be surprised if the info you found is now outdated.

  Printing subject lines and headers, it is not possible to print. The reason is because many users are trying to print photos or documents. In the current situation, if a user were to send an email empty then the only thing that could print would be the attachment. This prevents clients a sheet of paper and the Ink/toner used to print.

  If you have the printer print senders and subject lines you can do so by having the sender to include in the body of the email. Another alternative is to set up an email address which is the sole purpose is to forward emails to the email address of the printer. This way if it is configured to include the information in the body so you will have those printed on the page. Also, this gives the advantage of having a backup of email messages sent to the address of the ePrint printer and if something should happen to the ePrint address, you can change the forwarding address that the email and no one would never know there was a problem.

  Please let me know if you have any other questions. If not, have a great week!

  If this solves your problems, please help other users find this thread by clicking on accept Solution below my post.

  If you appreciate my help, please inform other users by clicking on the icon below my post thumbs up.

• Windows 8 does not recognize most of the new software CD how can I download new printer drivers?

  Once more, Microsoft has outdone himself. The previously blindingly simple and obvious has been complicated to make incredibly frustrating and painful for users of the new version of windows. Why in the world 1/2 old software CD automatically recognized by Windows 8 and the other 1/2 no? None of these programs and their CDs are particularly old or dated. Worse still, I have a Canon printer and rickety Windows 8 will not load automatically when I insert the installation CD. And windows does not show the CD when I do a search in D: drive. How and why are you people so incompetent?  I'm sorry to be rude and mean, but seriously. The whole bloody point of tech and people like you is to operate more easy is DO NOT IMPOSSIBLE, TIME CONSUMINGLY DOULOUREUX.

  Hello

  Just kind of guessing here, but you could browse through your control panel... "AutoPlay" settings and see if it can just be a problem with setting...

  Another possibility is that one of your programs blocking access to some of the CD...

  Some programs have the option of 'Ownership' of your drive, for lack of a better description...

  iTunes can possibly do this and some CyberLink programs... There are other institutions...

  Another possibility is that some of them may be blocked by Windows because of compatibility issues...

  Some windows updates do precisely that for some programs.

• How to remove the part of an object grouped several using a shape (Pathfinder does not work, cannot get the knockout groups to work)? Kind of like the opposite of a clipping mask.

  I want to remove the portion of these legs inside of this graph, because a white circle solid at the Center intensifies the effect of the spiral.

  Background, the spiral is a mixture of the people flying around in a circle. The circle is then copied and turned several times. I have not developed the appearance again.

  There must be an easy way to do it, but I can't use the Pathfinders, the opacity mask, knockout groups, and make simple layers does not work. I just want to axe the legs of these easy people!

  

  

  

  This is not correct

  

  I do several models and want to find a way to make it easy and fast!

  

  Thanks to you all!

  Emmanuel,

  If I (put) correctly, you should be able to get the opacity mask to work as follows:

  Select (only) the White path and the mixture and then in the transparency palette flyout on create with unchecked Clip opacity mask and mask invert checked.

  Who must hide the inner part of the mixture corresponding to the white circle and let the front remains visible oin the background (circle and all that.)

  .