Cisco 6961 handset hook

Similar Questions

• E900 - how to change the wireless channel?

  Hello people!

  I just bought a router Linksys Cisco E900 and hooked it up to my cable Internet. The Internet service that gives me my ISP is PPPoE, fiberlink (100 Mbps).

  I did the whole upward. I've connected my computer (via Ethernet cable) and my laptop (via radio) to the router.

  Now... There are other networks wireless around me. The Wi - Fi channel that my fixed router 1 is apparently - he saw settings. But I can't find a menu anywhere in the gateway of the router (192.168.1.1) I can change the wireless channel bandwidth wireless etc. Can someone tell me if I can change them...? If so, how? If not... that the steering wheel...

  Thanks in advance.

  Check the screenshots below.

  

  

• Cisco SPA232D ATA and Cisco SPA302D Wireless roaming handset

  I read the documentation of SPA 232D and I see that it supports up to 5 stations 302D SPA.

  In this project, I have 4 floors and we need a total of 15 phones:

  3 - basement

  5 - ground

  4 - first floor

  3 - second floor

  When the person is using the basement 302D phone have no reception when they walk on the upper floor.

  Can we do roaming between 232D? Is it possible to interconnect their? The range in the documentation may not be enough.

  What would be the recommended Cisco solution for this, we want to use DECT.

  Range: Indoor: 165 ft (50 m). Outdoor: 980 ft (300 m)

  Thanks for thinking of the spa232d for this project,

  Unfortunately with the current firmware it does not support combined roaming between base stations.  There is not an easy way to transfer between units handsets (you must unsubscribe from a base station and register again with the 2nd spa232d).

  The distance of the datasheet is optimal in a perfect environment, and I expect to be a little less real world.

  I woud suggest get a spa232d and a spa302 (maybe a dealer demo unit) and test range on the customer site.  Basically, do a site survey to see where the best place in the unit.

  If you need more 5 units on a floor, or signal will not reach both ends of the beach, 2 - spa232d devices may be necessary.  Some devices would be recorded to one, some to the other.

  There is good documentation on configuration and management with the device calls here.

  SPA232D & SPA302D: Introduction to the call routing scenarios advanced

  https://supportforums.Cisco.com/docs/doc-30269

  Let me know if you have more questions.

  Dan

• Droid Turbo could not connect the Cisco access point

  Greetings.

  Since the upgrade to a droid turbo, I was unable to connect to the network without wire of my work. I work in the it Department, but my experience with Cisco technologies and wireless is limited, so I tried to understand why. My previous bike x worked fine. We have a network of all the access points managed by a controller Cisco 4402 running version 7.0.98 of the BONES. I was able to connect to another wireless network that I could meet outside of work, and I am able to connect to the network of my work if I connect it is unsecured guest SSID. Only connections to our 4 secure networks fail. The controller reports that my phone cannot all simply to authenticate. The controller is configured for WPA2 / AES using a key 284 on the particular network, that I am trying to connect. I entered this key manually both via copy and paste. As far as my phone goes, I only tried to withdraw and time networks like tent to start it in safe mode without success. I read on various forums android that maybe it's a problem related to Kit Kat and this kind of problem has appeared on other handsets from other manufacturers, but nothing definite.

  Any suggestions would be much appreciated.

  -Josh

  Let me direct you to two other discussions here on the Droid Turbo forum and the other from Cisco which may help.

  Unable to connect to company wifi

  https://forums.Motorola.com/posts/af633eb3e4

  DROID WiFi Turbo questions

  https://forums.Motorola.com/posts/06a2f3c5ca

  Connectivity issues with Cisco and Moto X (Gen 2) allowed RMC controllers (probably related)

  https://supportforums.Cisco.com/discussion/12331486/connectivity-issues-Cisco-controllers-and-PMF-enabled-Moto-x-Gen-2

  I hope this helps!

• LAN does not work when the Cisco E1000 router hangs

  Original title: Download sp3

  Remember - this is a public forum so never post private information such as numbers of mail or telephone! I bought recently a new Cisco E1000 router. My computer is a laptop model Lenovo 0769.

  I am running windows XP with sp2. The cisco software requires sp3. I called support of cisco and even they couldn't get to download sp3. My network is wireless on the router and I had to install from another laptop computer on the system. My LAN does not work when hooked. What do you suggest to me.

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hi mdenrique,

  1. what exactly do you mean by LAN (Local Area Network) does not work? You get the error message?

  If you have not installed Service Pack 3, try the following steps:
  Step 1: Download Service Pack 3
  see How to obtain the latest Windows XP service pack .
  b. scroll the window and click on "Download now the Windows XP Service Pack 3 package" to download the service pack.
  c. save the file on the desktop.

  Step 2: Install Service Pack 3
  a. open the file downloaded and follow the instructions in the wizard to complete the installation.
  b. restart the computer once the installation is complete.

  For more information, see steps to take before you install Windows XP Service Pack 3

  Note: Once you have installed service pack 3, install the router and check if the problem persists.

  Step 3: To troubleshoot LAN, run home and small Office Networking Troubleshooter
  a. Click Start and then click Help and Support.
  b. under Pick a help topic, click Network and Internet.
  c. under network and the Web, click on resolution of networking or Web problems and then click on home and small Office Networking convenience store.
  d. answer the questions in the troubleshooter to try to find a solution.

  For more information, see the following articles:
  1 see How to troubleshoot a network in Windows XP
  2 see two resources to solve the problems of connection network in Windows XP

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Cisco/Linksys lacks a PCI Express Wireless N card for desktop computers

  I bought a new gateway last year and noticed that there is no PCI slot for an internal wireless card.

  I've been running on an adapter of game without external G wire hooked to my ethernet port.

  I want to update my system for Wireless-N dual band, but to eliminate the clutter of my office.

  Anyone have any idea when CISCO/Linksys will have to use a card PCI E N dual-band available?

  (I'm willing to beta-test)

  Bill Calderwood

  Quality Director

  Kadient

  You could use a PCIe to PCI card and then use any PCI device you want (as long as he did)

  http://www.Amazon.com/STARTech-PCI-Express-adapter-card/DP/B0024CV3SA

• Handset/headset Monitoring Query (Alternative to 7942G)

  Hello Cisco support community!

  I have another query concerning devices having the ability of monitoring handset/headset, currently our homes real estate 7942 g across contact center however, they recently became out of use and we were informed to improve our handsets to 7841 s due to being as for as in terms of capacity.

  However, this is not the case because there is no option for handset/headset in the device profile which is an important condition for the center of contact especially when training new officers.

  I got a glance at several data sheets and have had a look through the device of CUCM profiles and I can't find a newer model with this feature, I'm basically looking for an official reply see if there is another device that has this ability that is not the end of life.

  Additional info: CUCM 10.5 + UCCE/CVP environment

  Thanks in advance,

  Kind regards

  Christopher Hawkins

  Hi Christophe,

  With phones 7900 series as the 7942, this behavior was actually a bug until the release of the 8-5-x firmware. I really believe that they could not come up with a fix for this unexpected problem that some people close & desired and other hated and despised so they just made a real feature.

  CSCsr65970 - function to toggle audio played to the handset during a helmet

  Description

  Symptom:
  If you listen carefully, the phone will simultaneously play audio for headphones and combined
  at all times.
  
  Conditions:
  It is found on all phones 79XX until firmware 8.3 (5)
  
  Workaround solution:
  It is a specific configuration of the product now available in CCMAdmin > device > phone for phones 79 X 2 and X 5 79.
  Handset/headset Monitor:
  
  When the handset/headset control is enabled, a supervisor can pick up the idle handset/headset and hear the current call. For example, if an agent is on a call on the headset, a supervisor can hear the other party on the handset. Only the microphone on the active handset/headset is in use. For example, if an agent is running on the helmet, then the headset microphone is active and the microphone in the handset is disabled.

  Details

  First found in: (2)

  8.3 (5), 8.5 (2)

  Status:

  Terminated

  Last modification:

  Nov 09,2012

  Product:

  Cisco Unified IP Phone 7900 Series

  Platform:

  Depending on

  Severity:

  6 development

  So, if you look on the device for a 7942 page under the

  The product-specific Configuration layout

  you will find;

  Handset/headset Moitor - toggle

  This setting is not available on one of the more recent IP phones that you discovered

  In most cases people wanted this ability to 'training' as you require then the next best option are options wireless & wired (below below are examples) so that both the ' trainer and the trainee "can use their headset.

  For wireless headsets.

  Plantronics 03929-63 Wireless Headset Adapter training

  For wired headsets;

  Training of Plantronics Y cord adapter 27019-03

  See you soon!

  Rob

• Point of access Cisco Aironet 1200 series help

  We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?

  OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.

  I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.

• Problem with the Cisco ASA 5525 X SFR and Firesight high school

  Hi team,

  We have two ASA 5525 X installed on them and Firesight in a Linux VM whose two SFRs are registered with SFR failover mode. We use the SAA secondary off the hook if the primary fails to turn on the secondary manually switch the wan cable. I turn on the ASA secondary every weekend to take the configuration of the primary for the ASA and the SFR and close by button walk / stop.

  Last week I turn on high school ASA and the Firesight couldn't see the secondary SFR and show the message below:

  Module device heartbeat: device > don't send heartbeats.

  (I should mention I can Pinger the IP ADDRESS)

  I tried to study the problem without success.

  I also deleted the sensor just Firesight devices management in case something is stuck, and I'm trying to re added without success.

  I'm new in firepower so... any ideas?

  Thank you

  Finally, this problem has been resolved by the redefinition of firepower:

  see detailed here procedure to perform this redefinition;

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-firepower-service...

  Before that, it appeared that firepower was not very healthy:

  After a success "" configure Manager add xxxxx"command.

  the command of managers show show nothing;

  He should have shown this result:

  > Display managers
  Host: 193.193.2.75
  Registration key: AZERTY
  Inscription: pending
  State of the PRC:

  on the other hand, in expert mode, the following command shows several processes (and not in the normal state):

  sudo pmtool status | grep-i down

  Last point,

  After the recreation and reconfigure all this fire power, installed in the ASA secondary standby, was considered to be OK under Firesight health Monitor,.

  but after 10mins, it appeared in critical condition with the following message:

  "Interface"DataPlaneInterface0"receives not all packages.

  This is normal and due to the fact that Eve ASA receives no flow and the same goes for firepower inside this ASA;

  by performing a failover from the primary to the secondary ASA, this critical message disappeared for firepower inside the ASA Sec and appeared for firepower inside the ASA elementary school

• Call Manager Express has no type 6961

  Greetings

  I have a 1861 with cme 7.1 router (I think, I got this from the show - telephone services) and when I try to add a new phone 6961, I did not have this type of guy.

  Is it something about the compatibility of the cme ip phone or am I missing some configuration?

  Thank you

  Augusto,

  Support for the 6961 started CME version 8.0 for SCCP and 9.0 for SIP

  See the CME software compatibility matrix

  http://www.Cisco.com/en/us/docs/voice_ip_comm/cucme/requirements/guide/33matrix.htm

  Kind regards
  Alex.
  Please evaluate the useful messages.

• Cisco 4510R + E power redundancy without PoE

  I'm picking a diet for a WS-C4510R + E chassis with eight line cards WS - X 4748-RJ45-E (no PoE) and two supervisors 7-E WS - X 45 - Sup. The Cisco Power Calculator says I'm good to go with 'Handset 1400 Watt - Data Only' (PWR-C45-1400AC) with the participation of 200-240 VAC, but I wonder about the redundancy.

  "Handset" means that I have to run both of them at the same time to supply the fully loaded chassis? Or I am able to do with just one?

  HI -.

  According to your specifications, the calculator indicates that you should provide about 1800W chassis to power all line cards.  Since the 1400W P/S is not sufficient in itself, you then run 2 x 1400 in handset mode.  If you wanted the power redundancy, then you have to meet food 2800W (PWR-C45-2800ACV). Fixed: out redundant data would require the P/S 6000W. (I reread the technical and calculating power plug).

  4500th Datasheet

  PSC

• Cisco UCS components and software bug

  I was reading on the Cisco products affected by the vulnerability of software to the following Cisco Security Council

  http://Tools.Cisco.com/Security/Center/content/CiscoSecurityAdvisory/CIS...

  I couldn't find if below products/components are affected by this problem... can someone confirm if these products/components are vulnerable to the software?

  Cisco UCS Manager

  Integrated management of Cisco (CIMC) controller

  Cisco UCS blade chassis

  TIA

  I agree that sentence is a bit off, note that the view talking affected _products_ (or not), not specific _components_ of a product.

  UCS seems to be off the hook. Not affected are:

  • Cisco UCS series B (blade) servers
  • Cisco UCS C-Series (Stand alone Rack) servers
  • Cisco UCS Central
  • Cisco UCS fabric of interconnections
  • Systems Cisco UCS Invicta series Solid State

  MMIC and UCSM would be part of the FI or B-or-C-series, etc.

• Cisco AP 1242 IOS and antenna

  People just a quick question about Cisco AP 1242... which is the recommended IOS for 1242 to make autonomous AP. in the second place, I received the new AP and to my surprise when I open it I can't find no antenna with it. My question is will it work without antenna then what antenna devrais I buy keeping in mind that I will be making it autonomous Ap with router ADSL heard they have different antennas

  Kindly help

  So why would cisco sell Ap without antenna this is very starnge as per your say it will not work which is very starnge......

  It is not strange.  It's logical.  How do I know what Cisco antenna, as a customer, you want?

  I am setting this AP as autonomus and will hook up with ADSL modem so kindly advise the Antenna's shd i but all four.

  I gave you the part numbers and I gave you the link to the document.  It's now your job to choose the one you want.  A single 1240 to ideally two 2.4 Ghz and two 5.0 Ghz antenna.  Optionally, disable either radios or possibly disable diversity.

• Configuration VPN Cisco ASA5505 new 800

  I have 2 office buildings using routers Cisco 800 series with a L2L VPN between the two.  I'm upgrading from the router to an ASA5505 at one of the offices but cannot understand the L2L VPN on the SAA.  Specifically, may not know how to set the pre-shared key.  On the Cisco 800 there:

  ISAKMP crypto key address

  This doesn't seem to work on the SAA.  Can anyone help this?  Here is my current config on the Cisco 800...

  crypto ISAKMP policy 10

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  ISAKMP crypto key

  address

  !

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac DUMAC3

  Crypto ipsec df - bit clear

  !

  MYmap 10 ipsec-isakmp crypto map

  defined by peer 75.148.153.217

  Set security-association second life 36000

  game of transformation-DUMAC3

  match address 101

  access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.7.0 0.0.0.255

  in your crypto-maps, the '10' and '65535' are the sequence numbers. A CM handset might look like this:

  address for correspondence primaryisp_map 10 101 crypto card

  peer set card crypto primaryisp_map 10 99.119.80.165

  primaryisp_map 10 set transform-set DUMAC3 ikev1 crypto card

  primaryisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  card crypto primaryisp_map interface primaryisp

• Cisco Voice Gateway with FXO of Telco, operation support for IP phone

  Hi all

  A very quick question.

  Incoming calls via telephone in a voice gateway company ending on a Cisco 7941 G.

  Is it possible for a Cisco 7941 IP handsets or others to instagate actuation when the call is active, then causes the RTC line provide the new key, and then a Telco on via DTMF the combined IP instagate transfer to another number.

  This feature works on a PABX Ericcson previously!

  Is hookflask taken analog device support ONLY?

  I think that the GUY supports, anyone got it working on CallManager?

  Concerning

  Andrew

  Fix Andrew, actuation on IP phone is supported only with the MAN not with CUCM.

  HTH

  GP.

  Pls rate useful messages!