Configuration VPN Cisco ASA5505 new 800

I have 2 office buildings using routers Cisco 800 series with a L2L VPN between the two.  I'm upgrading from the router to an ASA5505 at one of the offices but cannot understand the L2L VPN on the SAA.  Specifically, may not know how to set the pre-shared key.  On the Cisco 800 there:

ISAKMP crypto key address

This doesn't seem to work on the SAA.  Can anyone help this?  Here is my current config on the Cisco 800...

crypto ISAKMP policy 10

BA 3des

md5 hash

preshared authentication

Group 2

ISAKMP crypto key

address

!

!

Crypto ipsec transform-set esp-3des esp-md5-hmac DUMAC3

Crypto ipsec df - bit clear

!

MYmap 10 ipsec-isakmp crypto map

defined by peer 75.148.153.217

Set security-association second life 36000

game of transformation-DUMAC3

match address 101

access-list 101 permit ip 192.168.1.0 0.0.0.255 192.168.7.0 0.0.0.255

in your crypto-maps, the '10' and '65535' are the sequence numbers. A CM handset might look like this:

address for correspondence primaryisp_map 10 101 crypto card

peer set card crypto primaryisp_map 10 99.119.80.165

primaryisp_map 10 set transform-set DUMAC3 ikev1 crypto card

primaryisp_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

card crypto primaryisp_map interface primaryisp

Tags: Cisco Security

Similar Questions

  • LT2P configuration vpn cisco asa with the internet machine windows/mac issue

    Dear all,

    I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS.

    My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy

    It does not work. only the resources behind the firewall, I can access. I use the extended access list

    I tried also with the standard access list.

    Please please suggest what error might be.

    Thank you

    JV

    Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article:

    http://TechNet.Microsoft.com/en-us/library/bb878117.aspx

  • Configuration VPN Cisco RV110W.

    Hello

    We have a new RV100W router. I would like to use it for iPhone, PC and MAC for you connect via IPSec (QuickVPN) or PTTP.

    Whenever I go to the VPN configuration, it tells me that I need to set up a 10.x.x.1 network. How can I use VPN without doing?

    Thank you!

    Hi bndbrennan,

    Try to change the IP address, set up your VPN clients, and then restore the IP 192.168.1.1. The reason for which the router wants to change is because there are so many routers out there that have 192.168.1.1. If you always try to connect from one of these routers, the connection will fail. We see a lot of people that use 192.168.2.1 and it works fine.

  • Cisco 1921 - how to configure VPN multiple Tunnels to AWS

    I have a router VPN Cisco 1921. I managed to create tunnel VPN Site to Site with AWS VPN Tunnel 1. AWS offers 2 tunnels, so I created another card Crypto and attaches to the existing policy. But the 2nd tunnel won't come. I don't know what I'm missing... is there a special setup that needs to be done to allow multiple IPsec vpn tunnels on the same physical interface? I have attached a picture and included the configuration of my router, if it helps.

    C1921 #sh run
    Building configuration...

    Current configuration: 2720 bytes
    !
    ! Last configuration change at 02:12:54 UTC Friday, may 6, 2016, by admin
    !
    version 15.5
    horodateurs service debug datetime msec
    Log service timestamps datetime msec
    encryption password service
    !
    hostname C1921
    !
    boot-start-marker
    boot-end-marker
    !
    !
    logging buffered 52000
    enable secret 5 $1$ jc6L$ uHH55qNhplouO/N5793oW.
    !
    No aaa new-model
    Ethernet lmi this
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    !
    Research of IP source-interface GigabitEthernet0/1 domain
    IP cef
    No ipv6 cef
    !
    Authenticated MultiLink bundle-name Panel
    !
    !
    !
    license udi pid CISCO1921/K9 sn FTX1845F03F
    !
    !
    username admin privilege 15 password 7 121A0C041104
    paul privilege 0 7 password username 14141B180F0B
    !
    redundancy
    !
    !
    !
    !
    !
    !
    !
    crypto ISAKMP policy 10
    BA aes
    preshared authentication
    Group 2
    lifetime 28800
    ISAKMP crypto keys secret1 address 52.35.42.787
    ISAKMP crypto keys secret2 address 52.36.15.787
    !
    !
    Crypto ipsec transform-set AWS - VPN aes - esp esp-sha-hmac
    tunnel mode
    !
    !
    !
    map SDM_CMAP_1 1 ipsec-isakmp crypto
    Description Tunnel 1 to 52.35.42.787
    defined by peer 52.35.42.787
    game of transformation-AWS-VPN
    PFS group2 Set
    match address 100
    map SDM_CMAP_1 2 ipsec-isakmp crypto
    Description 2 to 52.36.15.787 Tunnel
    defined by peer 52.36.15.787
    game of transformation-AWS-VPN
    PFS group2 Set
    match address 100
    !
    !
    !
    !
    !
    the Embedded-Service-Engine0/0 interface
    no ip address
    Shutdown
    !
    interface GigabitEthernet0/0
    Description connection Wan WAN - ETH$
    IP address 192.168.1.252 255.255.255.0
    automatic duplex
    automatic speed
    map SDM_CMAP_1 crypto
    !
    interface GigabitEthernet0/1
    Description of the connection to the local network
    IP 192.168.0.252 255.255.255.0
    automatic duplex
    automatic speed
    !
    IP forward-Protocol ND
    !
    IP http server
    local IP http authentication
    no ip http secure server
    IP http timeout policy slowed down 60 life 86400 request 10000
    !
    IP route 0.0.0.0 0.0.0.0 192.168.1.254 permanent

    !
    recording of debug trap
    host 192.168.0.3 record
    host 192.168.0.47 record
    !
    !
    Note access-list 100 permit to AWS Tunnel 1
    Access-list 100 CCP_ACL category = 20 note
    access-list 100 permit ip 192.168.0.0 0.0.0.255 any what newspaper
    Note access-list 101 permit to AWS Tunnel 2
    Note access-list 101 category CCP_ACL = 4
    access-list 101 permit ip 192.168.0.0 0.0.0.255 any logexit
    !
    control plan
    !
    !
    alias con exec conf t
    SIB exec show int short ip alias
    alias exec srb see the race | b
    sri alias exec show run int
    !
    Line con 0
    exec-timeout 0 0
    Synchronous recording
    line to 0
    line 2
    no activation-character
    No exec
    preferred no transport
    transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
    StopBits 1
    line vty 0 4
    privilege level 15
    local connection
    transport of entry all
    transportation out all
    !
    Scheduler allocate 20000 1000
    !
    end

    There should be no second tunnel.

    I use either a peer or the other, but not both at the same time.

    To display both at the same time, you need to use the Tunnel interfaces.  Amazon would have you sent pretty much the exact commands to copy and paste into.

  • Configure the Cisco VPN client to pass through the VPN site-to-site (GUI)

    Hello

    I say hat the chain and responses I've seen to achieve this goal have been great...

    https://supportforums.Cisco.com/discussion/12234631/Cisco-ASA-5505-VPN-p...

    and

    https://supportforums.Cisco.com/document/12191196/AnyConnect-client-site...

    My question is "we will get this configuration by using the graphical user interface for someone who is not notified about the command line?"

    Thank you

    Of course, all this can be configured via ASDM.

    Looking at the second example you posted above, they point you first change:

    ACL split of the tunnel for the AnyConnect customer

    This Configuration > remote access VPN > network (Client) access > AnyConnect connection profile > (chose the profile and select Edit) > (choose "Manage" next to group policy) > Edit > advanced > Split Tunneling > ensure that the policy does not "Inherit" but rather "Tunnel network list below" > Unselect "Inherit" next to the network list, then 'manage '. Enter your networks you want in the GUI in this dialog box. Click OK all the way back to the main window ASDM and click on apply.

    You then change:

    Crypto ACL for the tunnel from Site to Site

    To do this, go to Configuration > VPN Site-to_site > connection profiles > (choose your profile and select edit) > add the VPN client address pool to the list of local network between protect networks. Yet once, click OK all the way back to the main window ASDM and click on apply.

    Then, allow the

    ASA to redirect back on the same interface traffic it receives

    .. is defined under Configuration > Device Setup > Interfaces. (check the box at the bottom of this screen). Click on apply

    Finally, there is the NAT exemption. For which go to Configuration > firewall > rules NAT. Add a NAT device rule before rules network object with Interface Source out, Source address your address pool VPN, the Destination address to include remote subnets and Action is Static Source NAT type source address and destination address remaining as original (i.e. without NAT). Once on OK all the way back to the main window ASDM and click on apply. Save and test.

    Good luck. Don't forget to note the brand and posts useful when your question is answered.

  • Another problem with the configuration of Cisco VPN Client access VPN Site2site

    We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site.  JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support.  So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0

    Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.

    CORP netowrk 192.168.1.0

    IP VPN 192.168.12.0 pool

    Colo 10.1.0.0 internal ip address

    Also, here's an example of my config ASA

    : Saved

    :

    ASA Version 8.2 (1)

    !

    hostname lwchsasa

    names of

    name 10.1.0.1 colo

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    backup interface Vlan12

    nameif outside_pri

    security-level 0

    IP 64.20.30.170 255.255.255.248

    !

    interface Vlan12

    nameif backup

    security-level 0

    IP 173.165.159.241 255.255.255.248

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    switchport access vlan 12

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    object-group network NY

    object-network 192.168.100.0 255.255.255.0

    BSRO-3387 tcp service object-group

    port-object eq 3387

    BSRO-3388 tcp service object-group

    port-object eq 3388

    BSRO-3389 tcp service object-group

    EQ port 3389 object

    object-group service tcp OpenAtrium

    port-object eq 8100

    object-group service Proxy tcp

    port-object eq 982

    VOIP10K - 20K udp service object-group

    10000 20000 object-port Beach

    the clientvpn object-group network

    object-network 192.168.12.0 255.255.255.0

    APEX-SSL tcp service object-group

    Description of Apex Dashboard Service

    port-object eq 8586

    object-group network CHS-Colo

    object-network 10.1.0.0 255.255.255.0

    the DM_INLINE_NETWORK_1 object-group network

    object-network 192.168.1.0 255.255.255.0

    host of the object-Network 64.20.30.170

    object-group service DM_INLINE_SERVICE_1

    the purpose of the ip service

    ICMP service object

    service-object icmp traceroute

    the purpose of the service tcp - udp eq www

    the tcp eq ftp service object

    the purpose of the tcp eq ftp service - data

    the eq sqlnet tcp service object

    EQ-ssh tcp service object

    the purpose of the service udp eq www

    the eq tftp udp service object

    object-group service DM_INLINE_SERVICE_2

    the purpose of the ip service

    ICMP service object

    EQ-ssh tcp service object

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0

    outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

    outside_pri_access_in list extended access permit tcp any interface outside_pri eq www

    outside_pri_access_in list extended access permit tcp any outside_pri eq https interface

    outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100

    outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface

    outside_pri_access_in list extended access permit icmp any any echo response

    outside_pri_access_in list extended access permit icmp any any source-quench

    outside_pri_access_in list extended access allow all unreachable icmp

    outside_pri_access_in list extended access permit icmp any one time exceed

    outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586

    levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

    levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0

    outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0

    outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0

    outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

    inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0

    Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list

    OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0

    L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

    pager lines 24

    Enable logging

    debug logging in buffered memory

    exploitation forest asdm warnings

    record of the rate-limit unlimited level 4

    destination of exports flow inside 192.168.1.1 2055

    timeout-rate flow-export model 1

    Within 1500 MTU

    outside_pri MTU 1500

    backup of MTU 1500

    local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask

    no failover

    ICMP unreachable rate-limit 100 burst-size 5

    ICMP allow any inside

    ICMP allow any outside_pri

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    interface of global (outside_pri) 1

    Global 1 interface (backup)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access

    NAT (inside) 1 0.0.0.0 0.0.0.0

    NAT (outside_pri) 0-list of access OUTSIDE-NAT0

    backup_nat0_outbound (backup) NAT 0 access list

    static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns

    static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns

    static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns

    static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns

    Access-group outside_pri_access_in in the outside_pri interface

    Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1

    Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254

    Timeout xlate 03:00

    Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA authentication enable LOCAL console

    AAA authentication http LOCAL console

    the ssh LOCAL console AAA authentication

    http server enable 981

    http 192.168.1.0 255.255.255.0 inside

    http 0.0.0.0 0.0.0.0 outside_pri

    http 0.0.0.0 0.0.0.0 backup

    SNMP server group Authentication_Only v3 auth

    SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Sysopt connection tcpmss 1200

    monitor SLA 123

    type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri

    Annex ALS life monitor 123 to always start-time now

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto ipsec df - bit clear-df outside_pri

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    card crypto outside_pri_map 1 match address outside_pri_1_cryptomap

    card crypto outside_pri_map 1 set pfs

    peer set card crypto outside_pri_map 1 50.75.217.246

    card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5

    card crypto outside_pri_map 2 match address outside_pri_cryptomap

    peer set card crypto outside_pri_map 2 216.59.44.220

    card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    86400 seconds, duration of life card crypto outside_pri_map 2 set security-association

    card crypto outside_pri_map 3 match address outside_pri_cryptomap_1

    peer set card crypto outside_pri_map 3 216.59.44.220

    outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    card crypto outside_pri_map interface outside_pri

    crypto isakmp identity address

    ISAKMP crypto enable outside_pri

    crypto ISAKMP policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 10

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    aes-256 encryption

    md5 hash

    Group 2

    life 86400

    crypto ISAKMP policy 50

    preshared authentication

    aes encryption

    md5 hash

    Group 2

    life 86400

    !

    track 1 rtr 123 accessibility

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.0 inside

    SSH timeout 5

    Console timeout 0

    management-access inside

    dhcpd auto_config outside_pri

    !

    dhcpd address 192.168.1.51 - 192.168.1.245 inside

    dhcpd dns 8.8.8.8 8.8.4.4 interface inside

    rental contract interface 86400 dhcpd inside

    dhcpd field LM inside interface

    dhcpd allow inside

    !

    a basic threat threat detection

    statistical threat detection port

    Statistical threat detection Protocol

    Statistics-list of access threat detection

    a statistical threat detection host number rate 2

    no statistical threat detection tcp-interception

    WebVPN

    port 980

    allow inside

    Select outside_pri

    enable SVC

    attributes of Group Policy DfltGrpPolicy

    VPN-idle-timeout no

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    internal GroupPolicy2 group strategy

    attributes of Group Policy GroupPolicy2

    Protocol-tunnel-VPN IPSec svc

    internal levelwingVPN group policy

    attributes of the strategy of group levelwingVPN

    Protocol-tunnel-VPN IPSec svc webvpn

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl

    username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard

    aard attribute username

    VPN-group-policy levelwingVPN

    type of remote access service

    rcossentino 4UpCXRA6T2ysRRdE encrypted password username

    username rcossentino attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    bcherok evwBWqKKwrlABAUp encrypted password username

    username bcherok attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username

    rscott username attributes

    VPN-group-policy levelwingVPN

    sryan 47u/nJvfm6kprQDs password encrypted username

    sryan username attributes

    VPN-group-policy levelwingVPN

    type of nas-prompt service

    username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0

    username cbruch attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    apellegrino yy2aM21dV/11h7fR password encrypted username

    username apellegrino attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5

    username rtuttle attributes

    VPN-group-policy levelwingVPN

    username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin

    username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0

    username nbrothers attributes

    VPN-group-policy levelwingVPN

    clong z.yb0Oc09oP3/mXV encrypted password username

    clong attributes username

    VPN-group-policy levelwingVPN

    type of remote access service

    username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0

    username attributes finance

    VPN-group-policy levelwingVPN

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    type of remote access service

    IPSec-attributes tunnel-group DefaultL2LGroup

    Disable ISAKMP keepalive

    tunnel-group 50.75.217.246 type ipsec-l2l

    IPSec-attributes tunnel-group 50.75.217.246

    pre-shared-key *.

    Disable ISAKMP keepalive

    type tunnel-group levelwingVPN remote access

    tunnel-group levelwingVPN General-attributes

    address LVCHSVPN pool

    Group Policy - by default-levelwingVPN

    levelwingVPN group of tunnel ipsec-attributes

    pre-shared-key *.

    tunnel-group 216.59.44.221 type ipsec-l2l

    IPSec-attributes tunnel-group 216.59.44.221

    pre-shared-key *.

    tunnel-group 216.59.44.220 type ipsec-l2l

    IPSec-attributes tunnel-group 216.59.44.220

    pre-shared-key *.

    Disable ISAKMP keepalive

    !

    !

    !

    Policy-map global_policy

    !

    context of prompt hostname

    Cryptochecksum:ed7f4451c98151b759d24a7d4387935b

    : end

    Hello

    It seems to me that you've covered most of the things.

    You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel

    outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo

    Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.

    -Jouni

  • Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router

    Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.

    Someone please please suggest me something as soon as POSSIBLE.

    Thank you

    CLI version:

    http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00807ea936.shtml

    ASDM and SDM Version:

    http://www.Cisco.com/en/us/partner/products/ps5855/products_configuration_example09186a0080a9a7a3.shtml

  • Newbie configuration VPN 5505 for client Win7

    I have a client who has an installed 5505. They want VPN with their laptop Win7 but they don't want to shell out $1000 for customer VPN Cisco 10pcs.

    I have correctly set up the VPN without customer and through a browser, they can get to their files, but they would map network drives is just as if they were in the office.

    I tried to configure the IP Sec on 5505 and then using the built-in VPN Win7 network connection, but no go.

    I do also everything through the ASDM, but I know that certain things cannot be done. I prefer to use the ASDM!

    Anyone else get this set up? 99% of what I see here is how to connect the 5505 for VPN site to site.

    Thank you!

    Hello

    To my knowledge all ASA5505 should have the ability to have 2 VPN SSL connections with the Base license. To my knowledge, this also includes using the AnyConnect SSL VPN Client (which replaces the old VPN IPsec Client software) and the VPN without customer via the Web browser.

    The AnyConnect VPN Client should be available on the Flash of the ASA and is set when you configure the Client AnyConnect SSL VPN for the first time.

    On the ASDM, you should be able to configure the client AnyConnect SSL VPN with the "Wizard" as any other type of VPN configuration.

    The AnyConnect VPN Client is a better choice to use the old client IPsec, especially when it comes to new operating systems. The AnyConnect VPN Client can be installed in the ASA at the users computer when he or she first attempts to connect to the ASA via Web browser and connects with his credentials.

    -Jouni

  • Help configuration VPN 5505

    I am new to the use of Cisco devices and I need a little help with some configurations on an ASA5505 with 8.4.

    I want to connect 2 ASA5505 with a site-to-site.

    Site 1

    is where I want to connect to.  Site 1 we have access to 192.168.40.x and 192.168.42.x networks.  This ip is: 192.168.40.254

    Site 2

    I want to connect to site 1 and see the 40.x and 42.x networks.  I am able to connect to the network 40.x and can see devices on it, but I can't go to the 42.x network.  This ip device is: 192.168.50.1

    The sites are not in the same place, just in case someone asks about it.

    Hello

    Seems to me that you do not have good rules configured on Site1 and Site2 ASA on the VPN

    You must add the following configurations

    Site1

    access extensive list ip 192.168.42.0 inside_nat0_outbound allow 255.255.255.0 192.168.50.0 255.255.255.0

    access extensive list ip 192.168.42.0 outside_cryptomap allow 255.255.255.0 192.168.50.0

    -It would add both traffic between networks for VPN configurations and unnated traffic through to the remote end

    Site2

    outside_cryptomap to access extended list ip 192.168.50.0 allow 255.255.255.0 192.168.42.0 255.255.255.0

    This would add the traffic between networks for VPN configurations

    Seems that you already have the NAT0 configurations in place for networks, but not above the line for the VPN itself.

    Please rate if it helped

  • Check the ISE for the VPN Cisco posture

    Hello community,

    first of all thank you for taking the time to read my post. I have a deployment in which requires the characteristic posture of controls for machines of VPN Cisco ISE. I know that logically once a machine on the LAN, Cisco ISE can detect and apply controls posture on clients with the Anyconnect agent but what about VPN machines? The VPN will end via a VPN concentrator, which then connects to an ASA5555X that is deployed as an IPS only. Are there clues to this?

    Thank you!

    The Cisco ASA Version 9.2.1 supports the change in RADIUS authorization (CoA) (RFC 5176). This allows for the gesticulations of users against the ISE Cisco VPN without the need of an IPN. Once a VPN user connects, the ASA redirects web traffic to the LSE, where the user is configured with a Network Admission Control (NAC) or Web Agent. The agent performs specific controls on the user's computer to determine its conformity against one together configured posture rules, such as the rules of operating system (OS) patches, AntiVirus, registry, Application, or Service.

    The posture validation results are then sent to the ISE. If the machine is considered the complaint, then the ISE can send a RADIUS CoA to the ASA with the new set of authorization policies. After validation of the successful posture and CoA, the user is allowed to access internal resources.

    http://www.Cisco.com/c/en/us/support/docs/security/Adaptive-Security-Appliance-ASA-software/117693-configure-ASA-00.html

  • Client VPN Cisco router Cisco, MSW CA + certificates

    Dear Sirs,
    Let me approach you on the following problem.

    I wanted to use a secure between the Cisco VPN client connection
    (Windows XP) and Cisco 2821 with certificate-based authentication.
    I used the Microsoft certification authority (Windows 2003 server).
    Cisco VPN client used eTokenPRO Aladdin as a certificate store.

    Certificate of MSW CA registration and implementation in eToken ran OK
    Customer VPN Cisco doesn't have a problem with the cooperation of eToken.
    Certificate of registration of Cisco2821 MSW ca ran okay too.

    Cisco 2821 configuration is standard. IOS version 12.4 (6).

    Attempt to connect to the client VPN Cisco on Cisco 2821 was
    last update of the error messages:

    ISAKMP: (1020): cannot get router cert or routerdoes do not have a cert: had to find DN!
    ISAKMP: (1020): ITS been RSA signature authentication more XAUTH using id ID_FQDN type
    ISAKMP (1020): payload ID
    next payload: 6
    type: 2
    FULL domain name: cisco - ca.firm.com
    Protocol: 17
    Port: 500
    Length: 25
    ISAKMP: (1020): the total payload length: 25
    ISAKMP (1020): no cert string to send to peers
    ISAKMP (1020): peer not specified not issuing and none found appropriate profile
    ISAKMP (1020): Action of WSF returned the error: 2
    ISAKMP: (1020): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    ISAKMP: (1020): former State = new State IKE_R_MM5 = IKE_P1_COMPLETE

    Is there some refence where is possible to find some information on
    This problem? There is someone who knows how to understand these mistakes?
    Thank you very much for your help.

    Best regards
    P.Sonenberk

    PS Some useful information for people who are interested in the above problem.

    Address IP of Cisco 2821 10.1.1.220, client VPN IP address is 10.1.1.133.
    MSW's IP 10.1.1.50.
    Important parts of the Cisco 2821 configuration:

    !
    cisco-ca hostname
    !
    ................
    AAA new-model
    !
    AAA authentication login default local
    AAA authentication login sdm_vpn_xauth_ml_1 local
    AAA authorization exec default local
    AAA authorization sdm_vpn_group_ml_1 LAN
    !
    ...............
    IP domain name firm.com
    host IP company-cu 10.1.1.50
    host to IP cisco-vpn1 10.1.1.133
    name of the IP-server 10.1.1.33
    !
    Authenticated MultiLink bundle-name Panel
    !
    Crypto pki trustpoint TP-self-signed-4097309259
    enrollment selfsigned
    name of the object cn = IOS - Self - signed - certificate - 4097309259
    revocation checking no
    rsakeypair TP-self-signed-4097309259
    !
    Crypto pki trustpoint company-cu
    registration mode ra
    Enrollment url http://10.1.1.50:80/certsrv/mscep/mscep.dll
    use of ike
    Serial number no
    IP address no
    password 7 005C31272503535729701A1B5E40523647
    revocation checking no
    !
    TP-self-signed-4097309259 crypto pki certificate chain
    certificate self-signed 01
    30820249 308201B 2 A0030201 02020101 300 D 0609 2A 864886 F70D0101 04050030
    .............
    FEDDCCEA 8FD14836 24CDD736 34
    quit smoking
    company-cu pki encryption certificate chain
    certificate 1150A66F000100000013
    30820509 308203F1 A0030201 02020 HAS 11 092A 8648 01000000 13300 06 50A66F00
    ...............
    9E417C44 2062BFD5 F4FB9C0B AA
    quit smoking
    certificate ca 51BAC7C822D1F6A3469D1ADC32D0EB8C
    30820489 30820371 A0030201 BAC7C822 02021051 D1F6A346 9D1ADC32 D0EB8C30
    ...............
    C379F382 36E0A54E 0A6278A7 46
    quit smoking
    !
    ...................
    crypto ISAKMP policy 30
    BA 3des
    md5 hash
    authentication rsa-BA
    Group 2
    ISAKMP crypto identity hostname
    !
    Configuration group customer isakmp crypto Group159
    key Key159Key
    pool SDM_POOL_1
    ACL 100
    !
    the crypto isakmp client configuration group them
    domain firm.com
    pool SDM_POOL_1
    ACL 100
    !
    Crypto ipsec transform-set esp-3des esp-md5-hmac 3DES-MD5
    !
    crypto dynamic-map SDM_DYNMAP_1 1
    the transform-set 3DES-MD5 value
    market arriere-route
    !
    card crypto SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
    map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1 crypto
    client configuration address map SDM_CMAP_1 crypto answer
    map SDM_CMAP_1 65535-isakmp dynamic SDM_DYNMAP_1 ipsec crypto
    !
    ................
    !
    end

    status company-cu of Cisco-ca #show cryptographic pki trustpoints
    Trustpoint company-cu:
    Issuing CA certificate configured:
    Name of the object:
    CN = firm-cu, dc = company, dc = local
    Fingerprint MD5: 5026582F 8CF455F8 56151047 2FFAC0D6
    Fingerprint SHA1: 47B 74974 7C85EA48 760516DE AAC84C5D 4427E829
    Universal router configured certificate:
    Name of the object:
    host name = cisco - ca.firm.com
    Fingerprint MD5: E78702ED 47D5D36F B732CC4C BA97A4ED
    Fingerprint SHA1: 78DEAE7E ACC12F15 1DFB4EB8 7FC DC6F3B7E 00138
    State:
    Generated keys... Yes (general purpose, not exportable)
    Authenticated issuing certification authority... Yes
    Request certificate (s)... Yes

    Cisco-ca #sh crypto pubkey-door-key rsa
    Code: M - configured manually, C - excerpt from certificate

    Name of code use IP-address/VRF Keyring
    C Signature name of X.500 DN default:
    CN = firm-cu
    DC = company
    DC = local

    C signature by default cisco-vpn1

    IMPORTANT: I don't have a Cisco IOS Software: 12.4 (5), 12.3 (11) T08, 12.4 (4.7) PI03c,.
    12.4 (4.7) T - there is error in the cryptographic module.

    Hey guys, it's weird that the router is not find cert after IKE is the cert and validates, it is certainly not reason, but I would go ahead and set up the mapping of certificate on this router to force the client to associate with Group of IKE, for that matter, that you need to change your config a bit for use iskamp profiles :

    http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t8/feature/guide/gt_isakp.html

  • Remote VPN access - add new internal IP address

    Hello

    I have an existing configuration of Cisco VPN client in ASA 5510 for remote access.

    -------------------------------------

    Name of the Group: ISETANLOT10

    Group password: xxxx
     
    IP pool: lot10ippool, 172.27.17.240 - 172.27.17.245
     
    enycrption: 3DES
    authentication: SHA
    ------------------------------------
    the connection was successful, and I was able to ping to the internal server 172.47.1.10.
    Now, there is demand for remote access VPN even can do a ping to access a new server within LAN, 172.57.1.10 & 172.57.1.20
    But with the same VPN access, I was unable to ping the two new IP.
    How can I add both IP in order to make a ping by using the same configuration of remote access VPN?
    I have attached below existing config (edited version)
     
    ===

    : Saved
    :
    ASA Version 8.0 (4)
    !
    hostname asalot10
    names of
    name 172.17.100.22 NAVNew
    name 172.27.17.215 NECUser
    172.47.1.10 NarayaServer description Naraya server name
    name 62.80.122.172 NarayaTelco1
    name 62.80.122.178 NarayaTelco2
    name 172.57.1.10 IPVSSvr IPVSSvr description
    name 122.152.181.147 Japan01
    name 122.152.181.0 Japan02
    name 175.139.156.174 Outside_Int
    name 178.248.228.121 NarayaTelco3
    name 172.67.1.0 VCGroup
    name 172.57.1.20 IPVSSvr2
    !
    object-group service NECareService
    Description NECareService remote
    the eq https tcp service object
    EQ-ssh tcp service object
    response to echo icmp service object
    inside_access_in deny ip extended access list all Japan02 255.255.255.0
    inside_access_in ip VCGroup 255.255.255.0 allowed extended access list all
    inside_access_in list extended access deny tcp object-group PermitInternet any object-group torrent1
    inside_access_in list extended access allowed object-group ip PermitInternet any newspaper disable
    inside_access_in list any newspaper disable extended access allowed host ip NarayaServer
    inside_access_in list extended access permit ip host IPVSSvr all
    inside_access_in list any newspaper disable extended access allowed host ip NAVNew
    inside_access_in list extended access permit ip host 172.17.100.30 all
    outside_access_in list extended access allow object-group objects NECare a NECareService-group
    outside_access_in list extended access allowed host ip DM_INLINE_NETWORK_1 NarayaServer object-group
    outsidein list extended access permit tcp any host Outside_Int eq https
    outsidein list extended access allowed object-group rdp any host Outside_Int debug log
    outsidein list extended access allowed host tcp object-group DM_INLINE_NETWORK_2 eq Outside_Int 8080
    outsidein list extended access allowed host ip DM_INLINE_NETWORK_3 IPVSSvr object-group
    inside_mpc list extended access allowed object-group TCPUDP any any eq www
    inside_mpc list extended access permit tcp any any eq www
    inside_nat0_outbound list of allowed ip extended access all 172.27.17.240 255.255.255.248
    inside_nat0_outbound list extended access permit ip host NarayaServer Nry_Png object-group
    inside_nat0_outbound list extended access allowed host ip IPVSSvr2 172.27.17.240 255.255.255.248
    outside_cryptomap list extended access permitted ip object-group Naraya_Png-group of objects Nry_Png

    Global interface 10 (external)
    NAT (inside) 0-list of access inside_nat0_outbound
    NAT (inside) 10 0.0.0.0 0.0.0.0
    static (inside, outside) interface tcp 8080 8080 NarayaServer netmask 255.255.255.255
    static (inside, outside) tcp 3389 3389 NAVNew netmask 255.255.255.255 interface
    public static tcp (indoor, outdoor) interface ssh IPVSSvr2 ssh netmask 255.255.255.255
    Access-group outsidein in external interface
    inside_access_in access to the interface inside group
    Route outside 0.0.0.0 0.0.0.0 175.139.156.173 1
    Route inside 172.17.100.20 255.255.255.255 172.27.17.100 1
    Route inside NAVNew 255.255.255.255 172.27.17.100 1
    Route inside 172.17.100.30 255.255.255.255 172.27.17.100 1
    Route inside NarayaServer 255.255.255.255 172.27.17.100 1
    Route inside 172.47.1.11 255.255.255.255 172.27.17.100 1


    Route inside VCGroup 255.255.255.0 172.27.17.100 1

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define security association lifetime 28800 seconds
    cryptographic kilobytes 4608000 life of the set - the association of security of the 65535 SYSTEM_DEFAULT_CRYPTO_MAP of the dynamic-map
    card crypto outside_map 1 match address outside_cryptomap
    card crypto outside_map 1 set 218.x.x.105 counterpart
    card crypto outside_map 1 set of transformation-ESP-3DES-SHA
    outside_map map 1 lifetime of security association set seconds 28800 crypto
    card crypto outside_map 1 set security-association life kilobytes 4608000
    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    outside_map interface card crypto outside
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 30
    preshared authentication
    3des encryption
    md5 hash
    Group 2
    life 86400

    internal ISETANLOT10 group policy
    ISETANLOT10 group policy attributes
    value of server DNS 172.27.17.100
    Protocol-tunnel-VPN IPSec l2tp ipsec
    username, password nectier3 dPFBFnrViJi/LGbT encrypted privilege 0
    username nectier3 attributes
    VPN-group-policy ISETANLOT10
    username password necare encrypted BkPn6VQ0VwTy7MY7 privilege 0
    necare attributes username
    VPN-group-policy ISETANLOT10
    naraya pcGKDau9jtKgFWSc encrypted password username
    naraya attribute username
    VPN-group-policy ISETANLOT10
    type of nas-prompt service
    type tunnel-group ISETANLOT10 remote access
    attributes global-tunnel-group ISETANLOT10
    address lot10ippool pool
    Group Policy - by default-ISETANLOT10
    IPSec-attributes tunnel-group ISETANLOT10
    pre-shared-key *.
    tunnel-group 218.x.x.105 type ipsec-l2l
    218.x.x.105 group of tunnel ipsec-attributes
    pre-shared-key *.
    type tunnel-group ivmstunnel remote access
    tunnel-group ivmstunnel General-attributes
    address lot10ippool pool
    ivmstunnel group of tunnel ipsec-attributes
    pre-shared-key *.
    !

    =====

    Remote VPN access must allow the connection, but I'm guessing that your ASA does not know how to get to the two new destinations.

    You have a name and a static route to the job to 172.47.1.10 Server:

    name 172.47.1.10 NarayaServer description Naraya Server

    route inside NarayaServer 255.255.255.255 172.27.17.100 1

    .. but no equivalent for the two new hosts. As a result, all traffic of ASA destiny for them will attempt to use the default route (via the external interface).

    If you add:

    route inside 172.57.1.10 255.255.255.255 172.27.17.100

    route inside 172.57.1.20 255.255.255.255 172.27.17.100

    (assuming this is your correct entry), it should work.

  • Site to site VPN router-ASA5505

    Hello

    I have a problem with the VPN between ASA5505 and 3825 router.

    behind the ASA, we have a server that serves the specific port. If for any reason any link is disconnected assets if the VPN will become not we do not generate traffic to this server. After generating even a ping VPN immediately become active and communication starts. another case is when you reboot ASA the VPn is not created without ping server behind this ASA.

    How we could solve this problem without sending a traffing who serve?

    How remote access to this ASA, I can access internal interface? If I open access on port 443 on the external interface of asa could I access it? or I must also exclude this traffic VPN

    I used the VPN Wizard to configure on asa and CLI on router

    some troubleshootingand configuration commands, if this is not enough please let me know what you otherwise.

    Thanks in advance for your help

    ciscoasa # sh crypto isakmp his

    ITS enabled: 1
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 1

    1 peer IKE: 10.10.10.1
    Type: L2L role: initiator
    Generate a new key: no State: AM_ACTIVE

    Configuration of the SAA.

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    card crypto outside_map 1 match address outside_1_cryptomap
    card crypto outside_map 1 set pfs Group1
    card crypto outside_map 1 set counterpart 10.10.10.1
    map outside_map 1 set of transformation-ESP-DES-MD5 crypto
    outside_map interface card crypto outside
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    the Encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 30
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400

    the main router configuration

    crypto ISAKMP policy 1
    preshared authentication
    !
    crypto ISAKMP policy 5
    BA 3des
    preshared authentication
    Group 2
    !
    crypto ISAKMP policy 10
    preshared authentication
    Group 2
    crypto ISAKMP key 6 _JQfe [BeRGNBCGfbGxxxxxxxxx address 10.10.10.10

    Crypto ipsec transform-set esp - esp-md5-hmac xxxxx

    ETH0 2696 ipsec-isakmp crypto map
    defined peer 10.10.10.10
    Set transform-set xxxxx
    match address 2001

    access-list 2001 permit ip any 192.168.26.96 0.0.0.7

    Post edited by: adriatikb
    I just read somewhere that might change the type VPN "bi-direcitonal' two 'initiator' or 'answering machine' could help me but I test and no results.

    I had the same problem last week, and told the TAC engineer on our service ticket downgrade from IOS 8.2 (3) 8.2 (1).  Since then, it works fine.

  • Cisco ASA5505 with double tis + IPSEC

    Hello guys,.

    I have problem with double ISP + IPSEC on my cisco ASA5505 dry more license.

    Routing works OK (to connect to the Internet from siteA is work trought

    1 also second ISP) but IPSEC works trought just the first

    INTERNET SERVICE PROVIDER! There seemt that phase 1 and 2 of the Protocol IPSEC is correct but the packages

    Encrypt just but no not decryption. You have an idea what is the problem?

    I try to ping from the (PC - 10.4.1.66) siteA siteB (PC - 10.3.128.50)

    Thank you

    config site A:

    ##########################################################################

    ASA5505 Version 8.2 (1)

    interface Vlan1

    nameif inside

    security-level 100

    IP 10.4.1.65 255.255.255.248

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP 192.168.1.2 255.255.255.0

    !

    interface Vlan3

    internet nameif

    security-level 0

    IP address 212.89.235.yy 255.255.255.248

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    switchport access vlan 3

    outside_cryptomap list extended access allow icmp 10.4.1.64 255.255.255.248 10.3.128.0 255.255.255.0

    10.4.1.64 IP Access-list extended sheep 255.255.255.248 allow 10.3.0.0 255.255.0.0

    10.4.1.64 IP Access-list extended sheep 255.255.255.248 allow 10.16.0.0 255.255.0.0

    access inside extended ip permit list an entire

    extended permitted inside a whole icmp access list

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    Internet MTU 1500

    no failover

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 621.bin

    don't allow no asdm history

    ARP timeout 14400

    Global 1 interface (outside)

    Global interface (internet) 1

    NAT (inside) 0 access-list sheep

    NAT (inside) 1 10.4.1.64 255.255.255.248

    Access-group internet_in in interface outside

    internet_in group to access the Web interface

    Route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 track 1

    Internet route 0.0.0.0 0.0.0.0 212.89.235.yy 254

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    monitor SLA 123

    interface type echo protocol ipIcmpEcho 212.89.229.xx outdoor

    NUM-package of 3

    frequency 10

    Annex ALS life monitor 123 to always start-time now

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    3600 seconds, duration of life crypto ipsec security association

    Crypto ipsec kilobytes of life - safety 4608000 association

    card crypto outside_map0 1 match address outside_cryptomap

    card crypto outside_map0 1 set 212.89.229.xx counterpart

    outside_map0 card crypto 1jeu transform-set ESP-AES-256-SHA

    outside_map0 map 1 lifetime of security association set seconds 28800 crypto

    card crypto outside_map0 1 set security-association life kilobytes 4608000

    card crypto game 2 outside_map0 address outside_cryptomap_1

    outside_map0 interface card crypto outside

    outside_map0 card crypto internet interface

    ISAKMP crypto identity hostname

    crypto ISAKMP allow outside

    crypto ISAKMP enable internet

    crypto ISAKMP policy 3

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 300

    !

    track 1 rtr 123 accessibility

    Telnet 10.4.1.64 255.255.255.248 inside

    Telnet timeout 1440

    SSH 10.4.1.64 255.255.255.248 inside

    SSH 212.89.229.xx 255.255.255.255 outside

    SSH timeout 60

    SSH version 2

    Console timeout 0

    management-access inside

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    NTP server 194.160.23.2 source outdoors

    WebVPN

    attributes of Group Policy DfltGrpPolicy

    Protocol-tunnel-VPN IPSec l2tp ipsec

    username xx

    tunnel-group 212.89.229.xx type ipsec-l2l

    212.89.229.XX group of tunnel ipsec-attributes

    pre-shared-key *.

    siteA # sh crypto isakmp his d

    ITS enabled: 1

    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)

    Total SA IKE: 1

    1 peer IKE: 212.89.229.xx

    Type: L2L role: initiator

    Generate a new key: no State: MM_ACTIVE

    Encryption: aes - 256 Hash: SHA

    AUTH: preshared to life: 300

    Remaining life: 91

    # sh crypto ipsec siteA his

    Interface: internet

    Tag crypto map: outside_map0, seq num: 1, local addr: 212.89.235.yy

    outside_cryptomap list of access allowed icmp 10.4.1.64 255.255.255.248 10.3.128.0 255.255.255.0

    local ident (addr, mask, prot, port): (10.4.1.64/255.255.255.248/1/0)

    Remote ident (addr, mask, prot, port): (10.3.128.0/255.255.255.0/1/0)

    current_peer: 212.89.229.xx

    program #pkts: 7, #pkts encrypt: 7, #pkts digest: 7

    #pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

    compressed #pkts: 0, unzipped #pkts: 0

    #pkts uncompressed: 7, comp #pkts failed: 0, #pkts Dang failed: 0

    success #frag before: 0, failures before #frag: 0, #fragments created: 0

    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

    #send errors: 0, #recv errors: 0

    local crypto endpt. : 212.89.235.115, remote Start crypto. : 212.89.229.2

    Path mtu 1500, fresh ipsec generals 74, media, mtu 1500

    current outbound SPI: 2A9B550B

    SAS of the esp on arrival:

    SPI: 0xCF456F65 (3477434213)

    transform: aes-256-esp esp-sha-hmac no compression

    running parameters = {L2L, Tunnel}

    slot: 0, id_conn: 32768, crypto-card: outside_map0

    calendar of his: service life remaining (KB/s) key: (4374000/28629)

    Size IV: 16 bytes

    support for replay detection: Y

    Anti-replay bitmap:

    0x00000000 0x00000001

    outgoing esp sas:

    SPI: 0x2A9B550B (714822923)

    transform: aes-256-esp esp-sha-hmac no compression

    running parameters = {L2L, Tunnel}

    slot: 0, id_conn: 32768, crypto-card: outside_map0

    calendar of his: service life remaining (KB/s) key: (4373999/28629)

    Size IV: 16 bytes

    support for replay detection: Y

    Anti-replay bitmap:

    0x00000000 0x00000001

    # sh logging asdm siteA | I have 10.3.128.50

    6. 19 sep 2011 10:27:37 | 302020: built outgoing ICMP connection for faddr gaddr laddr 10.4.1.66/1024 10.4.1.66/1024 10.3.128.50/0

    6. 19 sep 2011 10:27:39 | 302021: connection of disassembly ICMP for faddr gaddr laddr 10.4.1.66/1024 10.4.1.66/1024 10.3.128.50/0

    config site B:

    ##########################################################################

    ASA 5510 Version 8.0 (4)

    interface Ethernet0/0

    nameif outside

    security-level 0

    IP address 212.89.229.xx 255.255.255.240

    OSPF cost 10

    interface Ethernet0/1.10

    VLAN 10

    nameif users

    security-level 50

    IP 10.3.128.0 255.255.255.0

    10.3.128.0 IP Access-list extended siteA 255.255.255.0 allow 10.4.1.64 255.255.255.248

    Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    3600 seconds, duration of life crypto ipsec security association

    Crypto ipsec kilobytes of life - safety 4608000 association

    outside_map crypto card 9 matches the address SiteA

    card crypto outside_map 9 peers set 212.89.229.xx

    card crypto outside_map 9 game of transformation-ESP-AES-256-SHA

    life card crypto outside_map 9 set security-association seconds 28800

    card crypto outside_map 9 set security-association life kilobytes 4608000

    outside_map crypto 10 card matches the address SiteA

    card crypto outside_map 10 peers set 212.89.235.yy

    outside_map crypto 10 card value transform-set ESP-AES-256-SHA

    life safety association set card crypto outside_map 10 28800 seconds

    card crypto outside_map 10 set security-association life kilobytes 4608000

    crypto ISAKMP policy 20

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    tunnel-group 212.89.229.xx type ipsec-l2l

    212.89.229.XX group of tunnel ipsec-attributes

    pre-shared-key *.

    tunnel-group 212.89.235.yy type ipsec-l2l

    212.89.235.yy group of tunnel ipsec-attributes

    pre-shared-key *.

    SiteB # sh crypto isakmp his d

    HIS active: 7

    Generate a new key SA: 1 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)

    Total SA IKE: 8

    8 peer IKE: 212.89.235.115

    Type: L2L role: initiator

    Generate a new key: no State: MM_ACTIVE

    Encryption: aes - 256 Hash: SHA

    AUTH: preshared to life: 300

    Remaining life: 245

    # Sh crypto ipsec SiteB his | b 212.89.235.yy

    current_peer: 212.89.235.yy

    #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

    decaps #pkts: 12, #pkts decrypt: 12, #pkts check: 12

    compressed #pkts: 0, unzipped #pkts: 0

    #pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

    success #frag before: 0, failures before #frag: 0, #fragments created: 0

    Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

    #send errors: 0, #recv errors: 0

    local crypto endpt. : 212.89.229.xx, remote Start crypto. : 212.89.235.yy

    Path mtu 1500, fresh ipsec generals 74, media, mtu 1500

    current outbound SPI: CF456F65

    SAS of the esp on arrival:

    SPI: 0x2A9B550B (714822923)

    transform: aes-256-esp esp-sha-hmac no compression

    running parameters = {L2L, Tunnel}

    slot: 0, id_conn: 4378624, crypto-card: outside_map

    calendar of his: service life remaining (KB/s) key: (3914999/27310)

    Size IV: 16 bytes

    support for replay detection: Y

    Anti-replay bitmap:

    0 x 00000000 0x00001FFF

    outgoing esp sas:

    SPI: 0xCF456F65 (3477434213)

    transform: aes-256-esp esp-sha-hmac no compression

    running parameters = {L2L, Tunnel}

    slot: 0, id_conn: 4378624, crypto-card: outside_map

    calendar of his: service life remaining (KB/s) key: (3915000/27308)

    Size IV: 16 bytes

    support for replay detection: Y

    # sh logging asdm siteB. I have 10.4.1.66

    6. 19 sep 2011 10:29:49 | 302021: connection of disassembly ICMP for faddr gaddr laddr 10.3.128.50/0 10.3.128.50/0 10.4.1.66/1024

    6. 19 sep 2011 10:29:50 | 302020: built ICMP incoming connections for faddr gaddr laddr 10.3.128.50/0 10.3.128.50/0 10.4.1.66/1024

    I'm glad that this answer to your question, feel free to mark the post as answered and the rate of useful messages

    Good day.

  • Cisco ASA5505 logging

    This is probably a very basic question...

    I have a new Cisco ASA5505 and I'm seeing newspapers at the level of the console. Currently when I make a record sh I just get the below. I expect, or I saw on messages system other PIX / ASA.

    Any ideas on what command I need to run in order to allow these messages?

    mipsasa01 # sh logging

    Syslog logging: enabled

    Installation: 20

    Logging timestamp: disabled

    Logging shall: disabled

    Refuse the Conn which full queue: disabled

    Recording console: disabled

    Monitor logging: disabled

    Logging buffer: disabled

    Logging trap: disabled

    A history record: disabled

    Device ID: disabled

    Logging of mail: disabled

    Logging ASDM: informational level, 7108 messages saved

    The "journal to see the" displays what is called the journal of the buffer. The registration of your buffer is disabled. Use cmd "logging buffered stored" config to activate it. You can adjust the size of the buffer with "logging buffer-size '. I think that buffer memory space is allocated in memory, so don't go overboard.

    http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/L2.html#wp1729451

Maybe you are looking for

  • iPhone 4 16 gb s

    I want to download the tweet app for ios 7.1.2

  • additional improvements

    Further improvements are needed? If yes what they could be?

  • Impossible to get a sound of sony computer

    Original title: my vaio sony says my audio player works well... but I still aint get no sound from my speakers my vaio sony says my audio player works well... but I still aint get no sound from my speakers

  • conversion of timestamp

    In the LV2009 extract attached, I use the "%b %Y % H: %m %d' for formatting timestamp in a time that looks like this: December 3, 2009 10:33.  Now what I want to do, is to receive a string (in this same format) and stuff it back into a TimeStamp.  Ho

  • Printer HP Laserjet installed - choose Properties causes the failure of protection

    Using Vista with a N 3500 HP color laserjet.  Worked fine for almost a year.  Then after an update of Windows - choose change properties in the printer driver causes a protection fault.  Cannot change the type of paper, hand feeding, color, copies et