Cisco 837 as router ADSL2 +.

Hey guys, I hope someone can answer a few questions I have and see on the setting of a configuration that I have problems with!

I have a situation where I have ADSL2 + with a couple of IP addresses additional, unfortunately my current router does not properly support Translation NAT, nor does it support additional IP on the same interface... so my solution was to fill the current router (Netgear DGN2000) and push it into a Cisco 837 I without apparent reason laying around.

My idea was to implement the Ethernet0 interface as a LAN interface and the Ethernet2 as a WAN interface traffic and route between them, but I have problems obtain the WAN to authenticate correctly - I never did authenticating PPPoE on a Cisco before, and even less when I do not use interfaces ATM0/Dialer0 of the to do!

My setup is attached as it is, I wasn't sure if I needed to configure the IP address of my real world interface Ethernet2, or the Dialer0 interface would take care of this for me? I used the advice of configuration in (http://www.cisco.com/en/US/docs/routers/access/800/819/software/configuration/Guide/9ppp_e_nat.html) to set up what I have now, but wasn't sure if it would work on a different device.

Last things, I read somewhere that the Ethernet interfaces on the 837 were 10Mbit only - this would mean that if I push my link ADSL2 + through it, I would not be able to get faster than that? Or he ignores what I physically connect through a FastEthernet port?

Thanks for any help you can give me on this.

Hi Damien,.

Your configuration as a result of problems:

Routing is disabled (I wonder how this happened) so the router is not a router at all. Fix this by adding the ip Routing and ip cef to your global configuration.
The VPDN turned on unnecessarily. Remove the VPDN configuration altogether by entering the No vpdn-group TPG and not activate vpdn in your global configuration.
Remove the interface Ethernet2 NAT configuration - this interface is not enabled, it is not necessary to configure IP NAT. enter no external ip nat in the Ethernet2 configuration.
On the interface Ethernet2, try to remove the enable pppoe command. This command enables the PPPoE server feature which is useless, because you are a customer. The only required command regarding the PPPoE is the configuration of customer, have you already present with the command pppoe client dial-pool-number 1 -command who must stay on Ethernet2.
Dialer1 interface, add the command ip tcp adjust-mss 1452 to make sure that the TCP sessions are not segments oversized requiring fragmentation. Add the ip nat outside command, as is the Dialer1 interface that is IP compatible interface to the outside world.
On the Dialer1 interface, the controls group dialer and ppp authentication are useless and should not be present. The first command sets a list of "interesting traffic" which can cause a dialer to dial a number, but this only applies to compounds such as analog modems or ISDN, not in PPPoE technology. The second command actually cause that you need your ISP to authenticate in some cases, and it won't. As a result, issue the following commands in the configuration of Dialer1:
1. No dialer-Group 1
2. no authentication chap pap callin PPP
Remove the route ip 10.0.0.0 255.0.0.0 Dialer1 static route and replace with ip route 0.0.0.0 0.0.0.0 Dialer1 -I suppose you want all internet connectivity through the Dialer interface.
Remove the ip nat inside source list internal interface Ethernet2 overload and replace it with the ip nat inside source list interface internal overload Dialer1 : this is the IP address of the Dialer1 you are hiding your internal network behind.

Try to make these changes and retest your connectivity. If it still does not please post your config then in force.

Best regards

Peter

Tags: Cisco Network

Similar Questions

CISCO 837 VPN Configuration

Configuration

my home pc (WIN XP + 4.6.03.0021 VPN Client dynamic IP) ===> internet ===> Corporate (CISCO 837--> LAN + static IP address)

Hello

I'm trying to set up a vpn between my pc at home and the CISCO837 company to access the local network.

I can connect to the CISCO but, I can't access any host on the local network.

Can someone help me with the basic configuration...

Homepage:

Dynamic IP (xxxx.xxxx.xxxx.xxxx)

Company:

Address IP WAN (yyy1.yyy2.yyy3.yyy4)

LAN IP range: (192.168.254.10--> 192.168.254.50)

Thank you

Hello..

1 - when you connect to the Cisco... What is the IP address that you receive from your Cisco VPN adapter. Devices on the local company network need to know how to get back to this IP address.

Can you please send the configuration of your router 837...

What is the latest firmware for Netgear DM111PUSP (router ADSL2 +)

Hi all

I had a router ADSL2 +, S/N: 1NU183GY040F7, DM111PUSP running the firmware version 3.63 c.
Looking at the firmware available in the downloads session, the listed models are DM111PSPv1, DM111PSPv2, DM111Pv1 and DM111Pv2 - I do not see DM111PUSP.
Grateful if someone can tell me what is the latest version of firmware for my DM111PUSP?

Thank you and best regards,

DP

Hello whlabel

Do you have this modem threw an ISP? because we are a few models that are sold to the ISP and they treat all the support for them.

DarrenM

IPSec VPN Site-to-Site router Cisco 837 to Firewall FortiGate 200 has

I had a challege for a site to site vpn scenario that may need some brainstorming you guys.

So far, I have had a prior configuration planned for this scenario, but I'm not very sure if the tunnel I created will work because I did not test it before with this scenario. I'll go next week on this project and hopefully get a solution of brainstorming you guys. Thanks in advance!

Network diagram:

http://cjunhan.multiply.com/photos/hi-res/5/3?xurl=%2Fphotos%2Fphoto%2F5%2F3

Challenge:

(1) configure CISCO R3 IPSec Site to Site VPN between 172.20.10.0 and 10.20.20.0 using cryptographic cards

(2) IKE Phase I MainMode, lifetime 28000, md5, DH-Group1

IKE Phase II: des-esp, hmac-md5, tunnel mode

PSK: sitetositevpn

Here is my setup for review:

crypto ISAKMP policy 10

the BA

preshared authentication

Group 1

md5 hash

ISAKMP crypto key sitetositevpn address 210.x.x.66

!

Crypto ipsec transform-set esp - esp-md5-hmac ciscoset

!

infotelmap 10 ipsec-isakmp crypto map

the value of 210.x.x.66 peer

Set transform-set ciscoset

match address 111

!

!

interface Ethernet0

3 LAN description

IP 10.20.20.1 255.255.255.0

IP nat inside

servers-exit of service-policy policy

Hold-queue 100 on

!

ATM0 interface

no ip address

ATM vc-per-vp 64

No atm ilmi-keepalive

DSL-automatic operation mode

!

point-to-point interface ATM0.1

IP address 210.x.20.x.255.255.252

no ip redirection<-- disable="">

no ip unreachable<-- disable="" icmp="" host="" unreachable="">

no ip proxy-arp<-- disables="" ip="" directed="">

NAT outside IP

PVC 8/35

aal5snap encapsulation

!

!

IP nat inside source list 102 interface ATM0.1 overload

IP classless

IP route 0.0.0.0 0.0.0.0 ATM0.1

IP route 0.0.0.0 0.x.0.x.190.60.66

no ip http secure server

!

Note access-list 102 NAT traffic

access-list 102 permit ip 10.20.20.0 0.0.0.255 any

!

access-list 111 note VPN Site-to-Site 3 LAN to LAN 2 network

access-list 111 allow 0.0.0.x.x.10.0 ip 10.20.20.0 0.0.0.255

Kind regards

Junhan

Hello

Three changes required in this configuration.

(1) change the NAT-list access 102 as below:

access-list 102 deny ip 10.20.20.0 0.0.0.255 172.20.10.0 0.0.0.255

access-list 102 permit ip 10.20.20.0 0.0.0.255 any

(2) place the card encryption on interface point-to-point ATM.

(3) remote all of a default route.

Thank you

Mustafa

Cisco e1000 only route when NAT disabled

I have a cisco e1000 itinerary. I already implemented a wireless network with success with cisco connect software. However, when I logged in the Web config, I disabled the NAT with routing table remains unchanged. the problem is that anyone of the network which links Internet WAN port can ping and receive the response of PCs within the wireless network, but it is impossible to reverse and all traffic inside e1000 can be passed through. Can someone explain this to me?

with NAT disabled, the E1000 actually forward packets from 192.168.0.*/24 to 192.168.1.*/24 and vice versa. However, this range is effective between these 2 networks only. If a PC inside 192.168.0.*/24 send a packet to the internet, the package will pass by E1000 without changing source IP(addressed 192.168.0.*) with the address of the E1000 Wan port. Arriving at the modem, the packet can be ignored, because the modem would NAT to only local source address (192.168.1. *) or even if the package were put to rout, he would have no chance to be routed by the backbone routers.

In addition, to be routed to 192.168.1.*/24 to 192.168.0.*/24, inside the 192.168.1.*/24 PC is configured by default with gateway 192.168.1.1 but the modem to a static route:

dest: 192.168.0.0 mask: 255.255.255.0 Gateway: 192.168.1.W interface: Lan (W is the port of E1000 WAN address)

and you can connect with 192.168.0.*/24 successfully.

to summarize, I think that disable NAT would win few benefits for your internet access. As my job now requires two network so I want the E1000 to operate as a regular IP for ease router. Once again thanks for your help

HP Touchpad browser works only with the Cisco Valet Plus router

I bought a 16 GB HP Touchpad several months ago and had been enjoying his excellent WiFi feature with my old G from Linksys WRT54GS wireless router until I replaced it with a new Cisco Valet Plus (model M20) wireless-N Router a couple of days.

Although I could easily and successfully, join the Touchpad to the Cisco Valet network, browser fails most of the time to load web pages. For example, if I go to www.yahoo.com, the browser is going to slowly load the web page, or it will expire with a pop-up message error "Impossible to load the Page. If I try to select a link from the homepage of Yahoo, it expires with the same message. And this happens for all web pages. If the initial page happens at all, I can then from this page a link to any other.

I know that the issue is not with the router because I have several other devices connected to it and they are all working well, including a laptop HP ProBook, an iPad and a Wii Console, I use to watch Netflix movies on. None of them has a problem - only the Touchpad.

If I go into settings-> Wi - Fi, it shows that the Touchpad is connected to Cisco network. And when I run the diagnostic system, it shows that the Wi - Fi works correctly.

Does anyone have an idea how to solve this problem?

I have found a workaround that did the trick. I had to change the channel setting auto on a coded hard 1 channel wireless.

Now, the Touchpad works very well, as well as all other devices that have worked.

Cisco SA540 - classic routing problem - 0.0.0.0 in static road

Hello, I am a bit newbie with routing device,

I had several public IP address

I got a Cisco Pix 501and want to replace it with a Cisco SA540

My Wan IP on Pix 501 is 195.68.x.z
My Lan IP on Pix 501 is 62.23.a.b (and 62.23.a.c,...)

My rules Pix 501 translation is: inside the interface. inside: everything: 0.0.0.0. Apart from the interface. same as orginal
My Pix 501 static route: outside | IP address 0.0.0.0. Mask 0.0.0.0. Gateway IP 195.168.x.y | Metric 1

So when a computer with 62.23.a.X want access to the internet the static route he say to throuw the 195.168.x.y of the IP Address of the gateway (as I undestand)

I replicate this config on my SA540

Also, through the Web user interface, I configure the Wan and Lan IP
and then in the routing menu, I check "Classic routing" so I go to the static Menu to add the same route as in my Pix 501, but I can't put 0.0.0.0 in iP address or IP subnet mask.

Can someone help me?

Thank you very much.

Hello

I hope this finds you doing well. Just thought I would add a few things here...

You have probably seen this, but... Here is the link to the page SA500:

https://www.myciscocommunity.com/docs/doc-10526

Yes, when you configure the device as a router, you need to configure routing. Try to remove the routes and the readd.

In addition, a little off topic, but if you want to stay with an ASA5505, there used to be a tool that would turn your PIX configus ASA. I don't remember where this link is now... but it used to fairly simple transition.

After you have configured the routing, since your internal machine, have you tried a trace route? On what device the traceroute fails?

In case you wish to speak to a support representative, here is the link to find the correct number:

http://www.Cisco.com/en/us/support/tsd_cisco_small_business_support_center_contacts.html

HTH,

Andrew Lee Lissitz

block websites Web of Cisco 800 series Router

Hello

I have a Cisco router running. I want to block certain websites (facebook, twitter, etc.) and download files with extensions such as

*.AVI, *.mp3, *.mp4, *.exe, *.wma, *.wmv and *.torrent etc...

I want to block for some users (based on the MAC address) and allow other users to have access to it on the same network.

Help me to do this?

Here's what you do:

IP block ip extended access list

allow an ip

permit tcp host 192.168.0.100 any eq www

permit tcp host 192.168.0.107 any eq www

I suggested to do the following:

IP block ip extended access list

permit tcp host 192.168.0.100 any eq www

permit tcp host 192.168.0.107 any eq www

Can't you see the difference?

Concerning

Alain

Remember messages useful rate.

PIX 501 for Cisco 3640 VPN router

-Start ciscomoderator note - the following message has been changed to remove potentially sensitive information. Please refrain from publishing confidential information about the site to reduce the risk to the security of your network. -end of the note ciscomoderator-

Have a 501 PIX and Cisco 3640 router. The 3640 is configured for dynamic map for VPN. The PIX 501 is set to pointing to the 3640 router static map. I can establish a tunnel linking the PIX to the router and telnet to a machine AIX on the inside network to the router. When I try to print on the network of the PIX 501 inside it fails.

What Miss me? I added the configuration for the PIX and the router.

Here are the PIX config:

PIX Version 6.1 (1)

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

enable encrypted password xxxxxxxxxxxxxxxx

xxxxxxxxxxxxx encrypted passwd

pixfirewall hostname

fixup protocol ftp 21

fixup protocol http 80

fixup protocol h323 1720

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol sip 5060

fixup protocol 2000 skinny

names of

pager lines 24

interface ethernet0 10baset

interface ethernet1 10full

Outside 1500 MTU

Within 1500 MTU

IP address outside dhcp setroute

IP address inside 192.168.1.1 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

PDM logging 100 information

history of PDM activate

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

Timeout xlate 0:05:00

Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

No trap to activate snmp Server

enable floodguard

No sysopt route dnat

Telnet timeout 5

SSH timeout 5

dhcpd address 192.168.1.2 - 192.168.1.33 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd outside auto_config

dhcpd allow inside

Terminal width 80

Cryptochecksum:XXXXXXXXXXXXXXXXXXX

: end

Here is the router config

Router #sh runn

Building configuration...

Current configuration: 6500 bytes

!

version 12.2

no service button

tcp KeepAlive-component snap-in service

a tcp-KeepAlive-quick service

horodateurs service debug datetime localtime

Log service timestamps datetime localtime

no password encryption service

!

router host name

!

start the flash slot1:c3640 - ik9o3s - mz.122 - 16.bin system

queue logging limit 100

activate the password xxxxxxxxxxxxxxxxx

!

clock TimeZone Central - 6

clock summer-time recurring CENTRAL

IP subnet zero

no ip source route

!

!

no ip domain-lookup

!

no ip bootp Server

inspect the name smtp Internet IP

inspect the name Internet ftp IP

inspect the name Internet tftp IP

inspect the IP udp Internet name

inspect the tcp IP Internet name

inspect the name DMZ smtp IP

inspect the name ftp DMZ IP

inspect the name DMZ tftp IP

inspect the name DMZ udp IP

inspect the name DMZ tcp IP

audit of IP notify Journal

Max-events of po verification IP 100

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

!

crypto ISAKMP policy 20

BA 3des

preshared authentication

Group 2

ISAKMP crypto key address x.x.180.133 xxxxxxxxxxx

ISAKMP crypto keys xxxxxxxxxxx address 0.0.0.0 0.0.0.0

!

!

Crypto ipsec transform-set esp-3des esp-sha-hmac vpn test

Crypto ipsec transform-set esp-3des esp-sha-hmac PIXRMT

!

dynamic-map crypto dny - Sai 25

game of transformation-PIXRMT

match static address PIX1

!

!

static-card 10 map ipsec-isakmp crypto

the value of x.x.180.133 peer

the transform-set vpn-test value

match static address of Hunt

!

map ISCMAP 15-isakmp ipsec crypto dynamic dny - isc

!

call the rsvp-sync

!

!

!

controller T1 0/0

framing ESF

linecode b8zs

Slots 1-12 channels-group 0 64 speed

Description controller to the remote frame relay

!

controller T1 0/1

framing ESF

linecode b8zs

Timeslots 1-24 of channel-group 0 64 speed

Description controller for internet link SBIS

!

interface Serial0/0:0

Description CKT ID 14.HXGK.785129 Frame Relay to Remote Sites

bandwidth 768

no ip address

no ip redirection

no ip unreachable

no ip proxy-arp

encapsulation frame-relay

frame-relay lmi-type ansi

!

interface Serial0 / point to point 0:0.17

Description Frame Relay to xxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 17 frame relay interface

!

interface Serial0 / point to point 0:0.18

Description Frame Relay to xxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 18 frame relay interface

!

interface Serial0 / point to point 0:0.19

Description Frame Relay to xxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 19 frame relay interface

!

interface Serial0 / point to point 0:0.20

Description Frame Relay to xxxxxxxxxxxxx location

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 20 frame relay interface

!

interface Serial0 / point to point 0:0.21

Description Frame Relay to xxxxxxxxxxxx

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 21 frame relay interface

!

interface Serial0 / point to point 0:0.101

Description Frame Relay to xxxxxxxxxxx

IP unnumbered Ethernet1/0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

No arp frame relay

dlci 101 frame relay interface

!

interface Serial0/1:0

CKT ID 14.HCGS.785383 T1 to ITT description

bandwidth 1536

IP address x.x.76.14 255.255.255.252

no ip redirection

no ip unreachable

no ip proxy-arp

NAT outside IP

inspect the Internet IP on

no ip route cache

card crypto ISCMAP

!

interface Ethernet1/0

IP 10.1.1.1 255.255.0.0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

no ip route cache

no ip mroute-cache

Half duplex

!

interface Ethernet2/0

IP 10.100.1.1 255.255.0.0

no ip redirection

no ip unreachable

no ip proxy-arp

IP nat inside

no ip route cache

no ip mroute-cache

Half duplex

!

router RIP

10.0.0.0 network

network 192.168.1.0

!

IP nat inside source list 112 interface Serial0/1: 0 overload

IP nat inside source static tcp 10.1.3.4 443 209.184.71.138 443 extensible

IP nat inside source static tcp 10.1.3.4 9869 209.184.71.138 9869 extensible

IP nat inside source 10.1.3.2 static 209.184.71.140

IP nat inside source static 10.1.3.6 209.184.71.139

IP nat inside source static 10.1.3.8 209.184.71.136

IP nat inside source static tcp 10.1.3.10 80 209.184.71.137 80 extensible

IP classless

IP route 0.0.0.0 0.0.0.0 x.x.76.13

IP route 10.2.0.0 255.255.0.0 Serial0 / 0:0.19

IP route 10.3.0.0 255.255.0.0 Serial0 / 0:0.18

IP route 10.4.0.0 255.255.0.0 Serial0 / 0:0.17

IP route 10.5.0.0 255.255.0.0 Serial0 / 0:0.20

IP route 10.6.0.0 255.255.0.0 Serial0 / 0:0.21

IP route 10.7.0.0 255.255.0.0 Serial0 / 0:0.101

no ip address of the http server

!

!

PIX1 static extended IP access list

IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

IP access-list extended hunting-static

IP 10.1.0.0 allow 0.0.255.255 192.168.1.0 0.0.0.255

extended IP access vpn-static list

ip permit 192.168.1.0 0.0.0.255 10.1.0.0 0.0.255.255

IP 192.0.0.0 allow 0.255.255.255 10.1.0.0 0.0.255.255

access-list 1 refuse 10.0.0.0 0.255.255.255

access-list 1 permit one

access-list 12 refuse 10.1.3.2

access-list 12 allow 10.1.0.0 0.0.255.255

access-list 12 allow 10.2.0.0 0.0.255.255

access-list 12 allow 10.3.0.0 0.0.255.255

access-list 12 allow 10.4.0.0 0.0.255.255

access-list 12 allow 10.5.0.0 0.0.255.255

access-list 12 allow 10.6.0.0 0.0.255.255

access-list 12 allow 10.7.0.0 0.0.255.255

access-list 112 deny ip host 10.1.3.2 everything

access-list 112 refuse ip 10.1.0.0 0.0.255.255 192.168.1.0 0.0.0.255

access-list 112 allow ip 10.1.0.0 0.0.255.255 everything

access-list 112 allow ip 10.2.0.0 0.0.255.255 everything

access-list 112 allow ip 10.3.0.0 0.0.255.255 everything

access-list 112 allow ip 10.4.0.0 0.0.255.255 everything

access-list 112 allow ip 10.5.0.0 0.0.255.255 everything

access-list 112 allow ip 10.6.0.0 0.0.255.255 everything

access-list 112 allow ip 10.7.0.0 0.0.255.255 everything

access-list 120 allow ip host 10.100.1.10 10.1.3.7

not run cdp

!

Dial-peer cor custom

!

!

!

!

connection of the banner ^ CCC

******************************************************************

WARNING - Unauthorized USE strictly PROHIBITED!

******************************************************************

^ C

!

Line con 0

line to 0

password xxxxxxxxxxxx

local connection

Modem InOut

StopBits 1

FlowControl hardware

line vty 0 4

exec-timeout 15 0

password xxxxxxxxxxxxxx

opening of session

!

end

Router #.

Add the following to the PIX:

> permitted connection ipsec sysopt

This indicates the PIX around all ACLs for IPsec traffic. Now that your IPSec traffic is still subject to the standard rules of PIX, so launched inside the traffic is allowed to go in, but off-initiated traffic is not.

IPSec site to site VPN cisco VPN client routing problem and

Hello

I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

There are on the shelves, there is no material used cisco - routers DLINK.

Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

Can someone help me please?

Thank you

Peter

RAYS - not cisco devices / another provider

Cisco 1841 HSEC HUB:

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

ISAKMP crypto key x xx address no.-xauth

!

the group x crypto isakmp client configuration

x key

pool vpnclientpool

ACL 190

include-local-lan

!

86400 seconds, duration of life crypto ipsec security association

Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

!

Crypto-map dynamic dynmap 10

Set transform-set 1cisco

!

card crypto ETH0 client authentication list userauthen

card crypto isakmp authorization list groupauthor ETH0

client configuration address card crypto ETH0 answer

ETH0 1 ipsec-isakmp crypto map

set peer x

Set transform-set 1cisco

PFS group2 Set

match address 180

card ETH0 10-isakmp ipsec crypto dynamic dynmap

!

!

interface FastEthernet0/1

Description $ES_WAN$

card crypto ETH0

!

IP local pool vpnclientpool 192.168.200.100 192.168.200.150

!

!

overload of IP nat inside source list LOCAL interface FastEthernet0/1

!

IP access-list extended LOCAL

deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

IP 192.168.7.0 allow 0.0.0.255 any

!

access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

!

How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

DE:

access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

TO:

access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

Also change the ACL 190 split tunnel:

DE:

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

TO:

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

Hope that helps.

Using Cisco AP as router and DHCP server

I'm a newbie in the technology of Cisco wireless. I have a lot of Cisco wireless access point. One of them (1142AG-K9 Cisco) I want to set them up as a DHCP server and will forward traffic to the public ip address as it will route the traffic to 203.82.203.50 (Ip provided by ISP) and will lease ip as associated devices 192.168.10.0 pool.

Even though I know that it is possible using a router on the AP. But it is possible using a single access point?

If so, how?

Help, please.

Hi, the AP cisco are just basic layer 2 devices such as a hub or Layer 2 switch, it does not any layer 3 as a wireless router.

The Cisco access point supports to have a VLAN or subnet configured or more VLANS or subnets and will pass all traffic to a layer 3 devic so that traffic can be routed to the need.

The Ap can't stand to have an addrees ip configured on the bvi1 for the management.

Also the build in the ap dhcp option is very limited and will only know the ip address to wirless clints that connect to it on an ssid linked to its management interface in this case that the bvi1 and all them VLAN othe or subnets shall not use an external dhcp server.

Sent by Cisco Support technique iPhone App

Cisco still sells router-AP (wireless routers) for domestic use

Well, do not really know where to ask
But what is described

Cisco router-point of access is great and fearsome performance for a domestic use, but cisco is still for sale? If so, can someone give me a link to the list of products?
Think so just to clarify, I'm not talking about Linksys wireless routers :)

If you are looking for equipment of the company, so it's Cisco, but since they let go the Linksys line, it is not any kind of home router AP. Cisco has an SME but that may not be what you want too.

http://www.Cisco.com/Cisco/Web/solutions/Small_Business/products/wireles...

Scott

Cisco 877 VPN router LAN access

I have spent much time already trying to figure out why I can't reach the LAN behind the router connecting through VPN, I thought it would be easier to ask people with more experience than me.

So, here he goes, this is the configuration of a router 877 adsl with some ACL defined for security and NAT/PAT, the VPN connects to customer VPN CIco however I don't see anything on the LAN to the remote computer (for example: cannot ping the router or server on the local network)

Also, since the router I can not ping the remote VPN computer when connected... I already tried a lot of different things, but my knowledge of cisco is limited, so I hope someone in this forum can sort it with little effort or change in this config... I replaced the ip addresses and passwords for security reasons.

In a Word, what is false or absent in this config which is not let me reach the LAN when docked hollow VPN?

Appreciate the help:

version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec localtime
encryption password service
!
hostname My877Router
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 XXXXXXXXXX
!
AAA new-model
!
!
AAA authentication login default local
connection of local AAA VPN authentication.
AAA authorization exec default local
local authorization AAA VPN network
!
!
AAA - the id of the joint session
clock timezone CST 9 30
!
Crypto pki trustpoint TP-self-signed-901674690
enrollment selfsigned
name of the object cn = IOS - Self - signed - certificate - 901674690
revocation checking no
rsakeypair TP-self-signed-901674690
!
!
TP-self-signed-901674690 crypto pki certificate chain
certificate self-signed 01
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
quit smoking
dot11 syslog
IP cef
!
!
inspect the IP router-traffic tcp name _OUTBOUND_
inspect the IP router traffic udp name _OUTBOUND_
inspect the name _OUTBOUND_ http IP
inspect the IP name _OUTBOUND_ https
inspect the IP dns _OUTBOUND_ name
inspect the IP router traffic icmp name _OUTBOUND_
no ip domain search
IP domain name mydomain.com.au
Name A.B.C.D IP-server
IP-name x.y.z.w Server
!
aes encryption password
!
!
username admin privilege 15 secret 5 #$% ^ & *.
Admin2 username privilege 15 secret 5 #$% ^ & *.
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
life 3600
!
ISAKMP crypto group configuration of VPN client
key 6 #$%^&_)(*&^%$%^&*(&^$
DNS 192.168.100.5
domain mydomain.com.au
pool VPN
ACL 100
Max-users 5
Max-Connections 1
netmask 255.255.255.0
!
86400 seconds, duration of life crypto ipsec security association
!
Crypto ipsec transform-set esp-3des esp-sha-hmac vpn1
!
Crypto-map dynamic dynmap 11
Set transform-set vpn1
market arriere-route
!
!
list of card crypto dynmap customer VPN authentication
card crypto dynmap VPN isakmp authorization list
client configuration address card crypto dynmap initiate
client configuration address card crypto dynmap answer
dynmap 11 card crypto ipsec-isakmp dynamic dynmap
!
Archives
The config log
hidekeys
!
!
!
type of class-card inspect VPN-match-all traffic
game group-access 100
!
!
type of policy-card inspect PCB-pol-outToIn
class type inspect VPN traffic
inspect
!
!
!
!
ATM0 interface
no ip address
no ip redirection
no ip unreachable
no ip proxy-arp
route IP cache flow
No atm ilmi-keepalive
PVC 8/35
aal5mux encapsulation ppp Dialer
Dialer pool-member 1
!
DSL-automatic operation mode
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
Description LAN_INTERFACE
IP 192.168.100.1 address 255.255.255.0
no ip redirection
no ip proxy-arp
IP nat inside
IP virtual-reassembly
route IP cache flow
IP tcp adjust-mss 1452
!
interface Dialer0
ADSL description
the negotiated IP address
IP access-group 101 in
Check IP unicast reverse path
no ip redirection
no ip unreachable
no ip proxy-arp
inspect the _OUTBOUND_ over IP
NAT outside IP
IP virtual-reassembly
encapsulation ppp
route IP cache flow
Dialer pool 1
No cdp enable
Authentication callin PPP chap Protocol
PPP chap hostname [email protected] / * /
PPP chap 7 76478678786 password
card crypto dynmap
!
local pool IP VPN 192.168.200.1 192.168.200.10
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 Dialer0
!
no ip address of the http server
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
IP nat inside source static tcp 192.168.100.9 443 interface Dialer0 443
IP nat inside source static tcp 192.168.100.9 25 interface Dialer0 25
IP nat inside source static tcp 192.168.100.9 1352 Dialer0 1352 interface
IP nat inside source static tcp 192.168.100.6 3389 3389 Dialer0 interface
IP nat inside source static tcp 192.168.100.7 3389 interface Dialer0 3391
IP nat inside source static tcp 192.168.100.3 8443 interface Dialer0 8443
the IP nat inside source 1 interface Dialer0 overload list
!
access-list 1 permit 192.168.100.0 0.0.0.255
access-list 100 permit ip 192.168.200.0 0.0.0.255 any
access-list 101 permit tcp any any eq 443 newspaper
access-list 101 permit tcp any any eq smtp newspaper
access-list 101 permit tcp any any eq 1352 newspaper
access-list 101 permit tcp A.B.C.D host any newspaper
access-list 101 permit tcp host x.y.z.w any log
access-list 101 permit tcp host r.t.g.u any log
access-list 101 permit udp any host x.x.x.x eq isakmp newspaper
access-list 101 permit udp any host y.y.y.y eq non500-isakmp log
access-list 101 deny ip any any newspaper
access-list 102 deny ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255 connect
access-list 102 permit ip 192.168.100.0 0.0.0.255 any what newspaper
Dialer-list 1 ip protocol allow
not run cdp
!
!
route allowed sheep 11 map
corresponds to the IP 102
!
!
control plan
!
Banner motd ^ C
Unauthorized access prohibited! ^ C
!
Line con 0
exec-timeout 20 0
no activation of the modem
line to 0
line vty 0 4
privilege level 15
entry ssh transport
!
max-task-time 5000 Planner
x.x.x.x SNTP server
y.y.y.y SNTP server
end

My877Router #.

Doesn't look like anything sent through the VPN tunnel. Decrypt the counter does not increase.

Can you please try to connect by a different ISP and see if that makes a difference?

You can also try to connect from another PC and see if that makes a difference?

The configuration on the router seems correct to me.

Configuration of CISCO VPN (WRVS4400N) router

Dear,

Please help me to setup VPN connection,

Headquarters: firewall fortigate-200B - SSL, IPsec

Branch: WRVS4400N Wireless-N Gigabit Security Router with VPN

The two sides have the public IP address

Wrong forum, post in the 'small business routers. You can move your ad using the Panel on the right actions.

VPN from CISCO 837

Hello everyone, I don't have much experience with network and just bought a 837 learn Hands on on the IOS configuration, so I need advice of all.

I'm currently train to connect to my local network at home via VPN (MS XP2 firmware) when I'm on the road on a latpop.

Reading, I understand that my IOS (c837 - k9o3sy6.123 - 11.T3.bin) is able to support:

1 EasyVPN Server

2. Act as a VPN server for MS XP to connect to.

My main goal is for my laptop to be able to connect to my files on a PC at home (which is on 24/7)

Is attached to a configuration that I tried, but without success.

What is happening is that when my laptop tries to connect, it always times out.

I am very sure that I tried to connect to the public IP address of my 837.

Any help is appreciated. And sorry for the need to spoon feed you, but I seriously want to learn and the information I see on the web is overwehlming...

Good fishing!

In my view, that the static nat command creates a mapping of permanent type for the inbound and outbound traffic. In this case, all incoming traffic will be forwarded to host 192.168.0.5. This includes the pptp traffic (gre and tcp 1723 port) which must be sent to the virtual access interface. Other statements of nat for tcp/udp ports do not affect the pptp traffic.

Cisco 837 as router ADSL2 +.

Similar Questions

Maybe you are looking for