Cisco Codec C40 remove wallpaper

Similar Questions

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.

• Cisco Codec C40

  I've recently updated the software on a device of cisco codec c40.

  The software has also updated the firmware on camera1.

  Unfortunately it didn't update the firmware on camera2.

  The cameras are connected in Garland.

  Is there a simple way to update the firmware on camera2? (Such as running certain commands on c40 codec?)

  Camera 1

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB50D00386 [ID:40083] 2012-12-10

  Camera 2

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB47D00079 [ID:40076] 2012-05-16

  See the following document, it is old, but still relevant.

  https://supportforums.Cisco.com/docs/doc-24351

• duplicate calls made using the alias between two codecs C40

  We have 2 new codecs C40.  When calling between the two using the alias, it seems that 2 calls are made.  In a sense, we get a very quick disonnect message upon acceptance of the call.  In the other direction, the call comes in, but on disconnect, we get a message saying missed call.

  Seems that the search rules can be duplication of the call some how - probably him endpoint becomes a call SIP and H.323 call at the same time. Could you post the call details and history/details of research?

  Sent by Cisco Support technique iPhone App

• Need help with the command options of codec C40

  Hello! I plan to buy a few codecs C40 and seller offers me to buy three options for this, but I can't find a description of these options. Seller is not so appropriate as I would like and these options cost a lot. They are here:

  LIC-INTP-C40-DD	Option of dual inclusive package C40
  LIC-INTP-C40-SM	IntPkg Codec C40, 4Way individual transcoding Multisite
  LIC-INTP-C40-PR	IntPkg Codec C40Premium resolution (1080 p/720 p 60) Option

  I found the document with similar options here (table 3), but there is also no description:

  http://www.Cisco.com/en/us/prod/collateral/ps7060/ps11304/ps11312/ps11332/data_sheet_c78-628593_ps11422_Products_Data_Sheet.html

  I think that these options it is me

  one) to use two screens (only two or more?) with C40

  (b) serve as C40 MCU for up to four sites without going through any additional autonomous MCU

  (c) to use video FullHD for videocalls (but I'll buy cameras 1080 p for C40, I need licence also for C40?)

  So, I would ask someone who is familiar with the command of Cisco/Tandberg to describe these options.

  You are actually right on your assumptions and descriptions, you just pretty much what each of these options do listed.

  Dual display-

  C40 has the ability to display the same video on both outputs by default, if you do not get this option.  This option is to display two separate video sources on two screens, such as: Farsite on output 1 and content/selfview on output 2.

  High resolution-

  You might be buying cameras 1080 p but resolution premium will allow you to pass resolutions higher during a call.  You can still view the full HD video when not in a call although if you choose not to get this option.

• matching codec c40 with ISDN link problem

  Hello world

  Would really appreciate if someone can help me with my problem.

  I have 2 sites. Each site has a c40 codec which is connected to a cisco ISDN link box. Each box contains 3 BRI connections. The system is essentially set up at the video-conference from one site to the other. C40 codecs have been paired with boxes of ISDN link manually due to the old firmware. Now that the firmware has been upgraded on all devices, I am trying to pair the codec with the ISDN link using the 'auto' mode so I can configure the ISDN codec c40 GUI link.

  The problem I have is that when I pair it in auto mode, the ISDN link is seen by the codec and matched succesffuly but I get an "error" and the reason for the error is "no sip registered to peripheral H320" or something of the sort. The rest of the configuration is the same, all im doing is pairing in auto mode. At this point, I can't do a video call-out. Can I make changes to the GUI hoewever c40 ISDN link and it shows as paired.

  When I change the sip profile out to 'off' in the sip codec c40 profile settings, now, there is no error. The sip profile in the ISDN link area is also set to off.

  Can someone help me what are the correct settings for outgoing SIP and the above error message please. It will be greatly appreciated.

  Thank you

  Hello

  Outgoing SIP should be turned off if you use the ISDN codec liaison, so please meke it took off.

  for the composition, should not use composition commnad complex that you scoop with TC 5.x and IT 1.0,

  With TC 6.x just enter number and select protocol H320.

  HTH

  Kind regards

  Dharmmesh

• Mounting ears for a Cisco/Tandberg C40

  I've been going around in circles now for weeks.  Anyone where I can retrieve a set of ears for a Cisco/Tandberg C40 system rack?

  I have a lot here that will not be used, which you can have for free. PM me with details.

  

  /Jens

• 1 2 codec C40 camera

  Hello

  One of our clients have existing C40 telepresence video system and they want to add another codec C40 and connect it to the camera of the current system of C40. One camera, shared in two units of codec C40. Same room/location where to install the additional codec.

  The goal, why the customer want this configuration because the existing system of the C40 was used by one of their partners and dedicated for that specific partner. They want to invest another C40 codec for their own video-conference sessions and for budgetary reason, that they just want to buy a codec and the use of the device the other C40 system's existing.

  Even audio and video resources will be used. Audio and video distribution amplifiers are not a problem on this configuration.

  My concern is that is - it possible to use a separator of type RJ45 for control of the camera's two codecs C40. The codecs will not be powered on at the same time.

  And what could happen and if two codecs are accidentally turned on simultaneously. ?? Can it damage the camera?

  Looking forward to your recommendations and your ideas.

  Thank you!

  Acevirgil

  Hi Acevirgil,

  This is something not an ideal package to the top and I do not thing anyone he tried again. and he's going to run on no it is not planned.

  Now you are going to use spillter on RJ45 and HDMI port,

  Remember, you make a divider appropriate according to the pinout of the control cable. If the cable is long enough according to the prescribed length you will need to turn on the external camera. and you question if the two codec lights suddenly the camera answer is NO (to me), that power is not very high.

  You can then go ahead and try first by a Dispatcher and test it before purchasing.

  It can work if the wiring is done correctly.

  Thank you

  Ravi kr.

• How can I enter a range of IP access codec C40 using RemoteAccess allow?

  Hello

  I'm setting up a codec C40 running Software 6.1.

  I want to limit systems that can access the codec through SSH/HTTP etc. and found authorize RemoteAccess under Configuration > System Configuration > network

  I want to enter a range of addresses (192.168.2.1 to 192.168.2.254) but may not work on the syntax to do this. The Administrator's guide and QAnywhere mention that ranges are supported but only provide examples for specific hosts.

  Can anyone help?

  Hello

  I think that the command affects the iptables on the codec which is a linux-based system.

  For the 192.168.2.1 to 192.168.2.254 range you might have to specify the following:

  xConfiguration network 1 RemoteAccess allow: "192.168.2.0/24.

  I tried this on my system:

  xConfiguration network 1 RemoteAccess allow: "144.254.10.0/24."

  Then the iptables show entry suite:

  [dderidde-ex90-home: / var/log/eventlog] $ iptables - n list

  INPUT string (policy ACCEPT)

  target prot opt source destination

  Admin channel (1 items)

  target prot opt source destination

  ACCEPT all les--144.254.10.0/24 0.0.0.0/0

  Drop tous--0.0.0.0/0 0.0.0.0/0

  That should do it I think.

  Danny.

• Cisco TelePresence system Codec C40

  I activated high security and after the reset mode, I can not connect with any account via the web site. Any suggestions?

  Keep informing me that the credentials are not valid...

  If there is no prompt to change your password to meet the security requirements (see the C40 Administrator's Guide pg 48), or you are not able to use or the old password (before being forced to change).  The only thing I can think is if you have no login required turn on to the serial port, you can directly connect the codec and change the admin password.  Essentially, you have forgotten the password and the only option is to reset factory endpoint, if it comes to it, see this discussion: password recovery.

• Updated codec C40 to the latest version of the TC software - use CUCM?

  I need to upgrade our C40 codecs to patch the vulnerability of Bash.  Currently they all run TC5.1.3.292001.

  I noticed a few options in the download options for the included C40.

  (1) Non-crypto and crypto software.  The way I read it, this refers only to the software itself, not any kind of codec options?

  (2) "to be used with CUCM"-I'm not sure how to check it. "  I inherited these devices with no documentation and the original seller is pretty useless.  Is it possible to check?  We use CUCM, but to my knowledge, our phones can't integrate directly with the TP system (we have customers MOVI for this).

  Stuart,

  I don't think that Cisco has published a version of TC software that has the fix vulnerabilities of bash.

  The non-crypto software has none of the feature SSL on it - IE. signaling/media figures. Usually goes with cryptography is the safer bet unless you're from a country that has to import restrictions.

  CUCM - if your termination points are saved to CUCM, then you must use the version of the file CUCM. It will be uploaded to the server CUCM himself by going to install/upgrade the Administration of Cisco's operating system and restart the TFTP service. In this way, the file will be pushed down from the server when the codec is reset.

  For the non-CUCM, you use the other file and download the .pkg directly on the codecs. It seems to me that you have a VCS based so the .pkg file deployment, this is what you will use.

• How to remove wallpaper changer, it will not delete, how can I get rid of it

  I put that stupid so-called toy, it changes your wallpaper for you, only problem, there is no way I can find to remove, won't let me not junk it. access is not allowed. Anyone know how to get rid of it?

  Hello

  What exactly happens when you try to uninstall this program? You get the error message?

  See the section below to uninstall any program.
  How to change or remove a program in Windows XP
  http://support.Microsoft.com/kb/307895

• How can I reinstall the codecs after removing the?

  I removed the codecs Windows Media Player of my programs and now can not watch videos and DVDs on my laptop.  Does anyone know how do I know which codecs I need and how to reinstall them?

  You still remember the name of the codecs that you deleted?

  Installation of FFDShow should allow WMP play the most widely used video and audio formats.

• How to dial directly to an IP address (point to point a.k.?) of the Codec C40

  We are looking to replace old Polycomm and Tandberg units with a telepresence C40 faithful.  On old Polycomm and Tandberg units, we can simply enter the endpoint IP address and connect.

  This unit of C40 has been attached to a CUCM and worked through their guardian.  We have done a factory reset the device, so we can move our network IP "Naked" in an accessible IP address.  However, we cannot make calls: it simply says 'Connection' and is there, doing nothing.

  Troubleshooting-> Diagnostics Web page, said "the call by default protocol is set to Auto, but the system is not registered on this Protocol".

  I guess the C40 can direct an IP address as our previous Polycomm and Tandberg units?

  Should what settings I use as the DefaultCall Configuration?  For the moment, it is 'auto '.

  In Configuration H323 I;

  NAT
  Set to Off.

  Profile 1
  CallSetup in direct mode
  PortAllocation the dynamic value

  Authentication
  LoginName is empty
  Set to Off
  Password is empty

  On the System Configuration in SystemUnit page I ContactInfo Type set to Auto.

  I don't know what I should put in E323Alias.  I guess it can be left blank?

  Help set up for direct IP point to point my calls really appreciated.

  Hi juddernaut,

  These forums seem a little foires right now and you have posted double https://supportforums.cisco.com/discussion/12137686/how-dial-direct-ip-a... (made it myself, because they take an age to the answer). I would like to delete the other post.

  Set the configuration of appeal to force H.323.

  The E.164 alias is a number as an extension system, but unless you have a doorman with dial plan of this won't be necessary and can be left blank. However, its value put something in the name of the system box so that the other side can see appealed.

  You should be able to dial via direct IP - I suspect his tent to dial via SIP and failing. Forcing them to use H.323 should do the trick.

  Chris

• Cisco Codec C20

  Hello

  Can we register C20 Codec to Cisco Call Manager 10.5.x since I was trying to look in add phone and get options like "Cisco Telepresence profile 42 (C20)" and "Cisco Telepresence Quick Set C20?

  We need to select and then to do the configuration.

  I can find the other CodecC40/C60/C90 in Call Manager.

  Please notify.

  regds,

  Aman

  They are different products, although the profile systems use the C20 his codec, they might have different options available to them than a C20 basis.  It is therefore preferable to use the device that corresponds to what you have.

  Insofar as a specific version, I don't have the answer, usually better to run the latest software codec version, except if there are bugs or problems with it that could prevent you to do so.