Mounting ears for a Cisco/Tandberg C40

Similar Questions

• rrack mounting brackets for Cisco switch SF300 - 48P?

  Does anyone know how to get grid mounting brackets for switch Cisco SF300 - 48P?

  You might be able to get them through the support of Cisco.  Check this thread: https://supportforums.cisco.com/discussion/11201291/sf-300-series-rack-m...

• Call SIP with Tandberg C40

  I have a Cisco Tandberg C40 codec and have been making H.323 calls for an organization with no problems.  The organization is now making changes and demanding that I connect to them with their new SIP address.  When I try to connect, it is said immediately that the call could not be connected.  What are the requirements for placing a SIP call with the Tandberg C40?

  Assuming your C40 has the version of the TC6.x software;

  go to network found under Control Panel Services and enable SIP.

  Don't forget of check that SIP is selected as the Protocol to call when calling this company that the default calling Protocol can be set to H.323, SIP and H.320, so if only make you SIP calls, and then upgrade the SIP, but if you do mostly H.323 calls, then put to H.323, and select SIP among the options of appeal when the dial - or even more easily, add this address to the local directory with specified as a SIP call Protocol.

  Just turning on SIP will allow you to make outgoing SIP calls, however, if this company wants to call you, then they can call you only using the public IP address of your system - and they could even not able to do according to their deployment, policies, etc.

  If you want people to be able to call you using a SIP URI as [email protected] / * /, then you need to register your system with a Registrar SIP CUCM, VCS - C, etc. and also have SRV SIP records in place.

  See the guide to the administrator for more information:

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC4/administration_guide/profile-c60_codec-C60-c40_administrator_guide_tc40.PDF

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.

• Record of equipment for the Cisco AnyConnect client NAM module

  Hi all

  Forgive me if this has been asked before or on the Cisco site somewhere (I could just find)

  Are there hardware specifications for the Cisco Anyconnect Network Access Manager module?

  Where can I find what wifi chipset is compatible with?

  Thanks in advance for your answer.

  Compatibility with the NAM module is based on the chipset not guest OS. The current operating system compatibility is listed here.

• For the Cisco router memory usage

  Hello

  We have a router SA520 (Firmware 2.1.18)

  We use only this for about 1 month now. Router seems ok it's just

  I am concerned about the use of memory who reach 62% (144/234 MB)

  What's to worry?
  How can I use that by cutting down the use?

  Excuse me, I'm just for new Cisco devices.

  Thank you very much.

  CA

  AC,

  Please go ahead and upgrade to the latest firmware 2.1.51 memory use should not be a problem. After the upgrade, please keep an eye on the back of the memory and the report.

  Thank you

  Jasbryan

  Support Cisco engineer

  .:|:.:|:.

• How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Dear all

  How to create a VPN file .pcf for the CISCO VPN CLIENT software profile

  Concerning

  Hi Imran,

  Can't do much about that because it depends on what authenticate you the VPN server and how the settings. But let me introduce you to the memory layout. Once you install and open a VPN client. Press it again and it opens up a new page for the VPN config.

  Example of configuration as it is attached. But it differs depending on the configuration of your vpn server.

  Once you create and save this profile. Your FCP file is stored.

  Please assess whether the information provided is useful.

  By

  Knockaert

• Evaluation version for the cisco secure access control server

  Hello

  I can get the trial version for the cisco secure access control server. IF SO pls send me the link.

  Thank you

  Hi Thomas,

  You can download ACS for windows 4.1 or 4.2 from the link below:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ACS-win-eval

  For ACS 5.x, please visit cisco.com

  Download software > Security > Cisco Secure Access Control System 5.x > Secure Access Control System Software

  HTH

  Kind regards

  Jousset

  Please evaluate the useful messages-

• Cisco Codec C40

  I've recently updated the software on a device of cisco codec c40.

  The software has also updated the firmware on camera1.

  Unfortunately it didn't update the firmware on camera2.

  The cameras are connected in Garland.

  Is there a simple way to update the firmware on camera2? (Such as running certain commands on c40 codec?)

  Camera 1

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB50D00386 [ID:40083] 2012-12-10

  Camera 2

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB47D00079 [ID:40076] 2012-05-16

  See the following document, it is old, but still relevant.

  https://supportforums.Cisco.com/docs/doc-24351

• The call history on Tandberg C40

  Can someone tell me where on a Tandberg C40 call history? I get frequent calls and crash and I can't tell where they come from.

  Thank you

  -mike

  Hello

  You can access C40 CLI (using SSH) and use the command xhistory.

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• Cisco Codec C40 remove wallpaper

  Hi all.

  In our installation of cisco telepresence, that we met an interesting question:

  the cisco c40 codec admin created a custom wallpaper, somehow this wallpaper was not appropriate for this codec for 100%.

  After that he transferred the wallpaper on the unit - it restarts. We see a cyclical reboot - boots of unity, we see a cisco logo, then we see a (part of the GUI) overlay on the monitor, after this codec is trying to load wallpaper, fails and went into reboot.

  Are there ways to manually remove this wallpaper of the codec s flash without hard resetting the codec?

  Hi Eugene,

  Try to login as an administrator using ssh/console and run the following command:

  xConfiguration video wallpaper: Summersky

  Best regards

  Sergey Kuzmin

• Is it possible to download a previous version of firefox that latest update blocks the characteristics I absolutely have to have for my cisco courses?

  I can't get my password box or my java tool correctly load or work on the update for firefox java tool is something that I have to complete my work in my cisco course. So I would like to know if there is a way to download and install an older version of firefox, so I have something I can do my job without having to use a browser that I don't have confidence.

  If you decide to try the version Extended Support Release (ESR) of Firefox, here is how I suggest to install:

  Clean reinstall it

  We use this name, but it isn't about deleting your settings, this is to ensure that the program, files are clean (not incompatible, corrupt or exotic code files). As described below, this process does not disrupt your existing settings. Don't uninstall NOT Firefox, that does not need.

  (A) download a fresh Installer for Firefox 38.2.0esr of https://www.mozilla.org/firefox/organizations/all/ in an ideal location. (Scroll down your preferred language).

  (B) the release of Firefox (if any).

  (C) to rename the program folder, either:

  (Windows 64-bit folder names)

  C:\Program Files (x86)\Mozilla Firefox
  

  TO

  C:\Program Files (x86)\Fx40
  

  (Windows 32-bit folder names)

  C:\Program Files\Mozilla Firefox
  

  TO

  C:\Program Files\Fx40
  

  (D) run the installer downloaded to (A). It should automatically connect to your existing settings.

  Install and run?

  Note: Some plugins can only exist in the old folder. If it is missing something essential, present in these files:

  • \Fx40\Plugins
  • \Fx40\browser\plugins

• Mount gray for disk encrypted in Recovery Mode

  I'm under the last El Capitan on a MacBook Pro for mid-2015. The internal boot drive is encrypted with FileVault. The issue I see is that when I boot into Recovery Mode so that I can run first aid on the boot volume, the "Mount" button is dimmed when I select the logical volume. Anyone know what I am doing wrong or what could be the problem?

  Thank you.

  You must first UNLOCK it. To do this, in Recovery Mode. Select the volume greyed, then click on edit on the menu bar and UNLOCK. Enter a password has been set to unlock the volume on startup.

• Camcorder mounted ceiling for filming of musician?

  Hello

  I'm pressed for room in my small studio where three tripods that I use with my camcorder to get in the way. The other challenge is as a performing musician, I stand and the tripods do not extend at the height of the head which is just more beautiful. So, I came up with a great idea!

  How about a ceiling camera bracket? Now, it could be a fixed monitoring type mount but have a more flexible design that would allow you to pull the camcorder to a variety of heights and angles. In this way I free up space and get a wide range of easy to build angles of camera from shoulder height or head.

  Someone at - he saw this idea? Please do (3) and I'll buy them!

  Thanks for the links to the same or other ideas,

  SFSaxguy wrote:

  ... a more flexible design...

  the more flexible design has (literally) the Gorilla Pod:

  

  (click on pic to amazon links)

  You can fold it, wrap, hang anywhere; I use a cheap clone to attach a photo inside a football goal...

  In different sizes / 'arm lengths. The original is more 'closed' = safer for the camera. In a shop of penny, once I bought something, basically a thick wire, soft plastic and a tripod connector... 2€ .... I would not use it to attach a Canon 5 Mk III, but hlds my sacrifice light and cheap cams anywhere...

  other options are so-called magic pliers:

  

  (you can detach the blind Flash connector and replace it with a screw standard 1/4 "...)

  First you close the clamp, then the other button to fix the arm in a position any.

  $ 15 (China direct) up to 50-$80 (Manfrotto... made in China)

  Comes in different lengths and sizes...

  Last option: cam Tape Gaffa Tape to the ceiling. -Gaffa is always an option

• Electronic mount EF for F5/F55?

  I've searched around and have heard conflicting reports on an electronic EF Mount for F5/F55. I mean by "electronic" opening contronl of Canon EF lenses.

  Is it that this will be a future option for these cameras or there will be just a silent mount? I see a lot of F5s sales if there is indeed an electronic Assembly. Thank you.

  I am currently using the FZ Optitek to mount EF with the controller "Optitron" on a Sony F3. It works as advertised.