Cisco Codec C20

Similar Questions

• Update codec C20/C40 cisco to 6.1.2 meetings lost contact with cisco

  So I improved a few Cisco C40 codec C20 5.1.6 to 6.1.2 the process was smooth.   He updated the device of the codec and cameras, but once the upgrade has completed, the touch screen of cisco lost all meetings.  Is there a way to put all meetings (from outlook calendars) of cisco press?

  A mixture of CUCM and TMS is not really possible.

  In any case, which concerned the TMS, can you set a password for the admin on the endpoint and then add this

  password under the connection tab in the Navigator system of this endpoint.

  After that do a force refresh and apply management settings and see if the meetings will appear again.

  As TMS pushes this information, it would be the correct symptom do not show this info when

  There is a communication / authentication problem.

• TANDBERG Codec C20 with software version TC4.0.3.243792

  Product: TANDBERG Codec C20 Software Version: TC4.0.3.243792

  Version: 2011-01-25

  Hello

  I have a C20 with an old TC4.0.3.x of output, I would like to upgrade to a later version to be able to do H323/SIP calls with an alias in front of the IP address with direct connection (no keeper). For example: [email protected] / * /. My understanding of this version TC4.0.3.x does not allow this type of call.

  How can I pass TC4.03.X which is obviously an outdated version of the 2011 now safely? From TC4.x to TC5.x? then TC6.x?

  How can I get the keys to release of Cisco in order to ensure that the updates will not be rejected due to the missing keys release?

  Thanks for your help.

  Hello

  You must have the keys to unlocking the main upgrade for each version.

  The same thing must be added before you do the upgrade.

  regds,

  Aman

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.

• The HDMI output on a Codec C20 is HDCP?

  I need to send the output of a CODEC C20 both a VGA and HDMI source.  HDMI output carries HDCP?

  No, this does not work.  I don't have or know of documented information, but only of in my environment it has not reported himself as a source HDCP.

• Cisco Codec C40

  I've recently updated the software on a device of cisco codec c40.

  The software has also updated the firmware on camera1.

  Unfortunately it didn't update the firmware on camera2.

  The cameras are connected in Garland.

  Is there a simple way to update the firmware on camera2? (Such as running certain commands on c40 codec?)

  Camera 1

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB50D00386 [ID:40083] 2012-12-10

  Camera 2

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB47D00079 [ID:40076] 2012-05-16

  See the following document, it is old, but still relevant.

  https://supportforums.Cisco.com/docs/doc-24351

• Simple question on a Cisco/Tandberg C20 codec

  Hi guys,.

  I would like to ask your advice on a question, one of our customers recently raised; Here's the short story:

  After that his ISP set at level a GK Radvision, customer knew no video, on its C20s, multi point conferences (video was successfully sent well).

  After an initial diagnosis, the customer said that the question can be put in the C20 non acceptance/negotiation QCIF video Protocol (used in Radvision and other old stuff eventually to join the Conference).

  As a solution, ISP has suggested to activate via SSH (command API) specific C20 (QCIF) Protocol (which is apparently not enabled by default... According to the ISP support)

  Now, I know, C20 already supports QCIF and has to be without having to activate it via the specific shell commands!

  ... Besides there no reference in the documentation of the API C20 on a specific command.

  What I suspect is that from time to time, an old codec ISDN connects to the Conference (perhaps as a first candidate) and somehow requires the MCU to negotiate some weird codec leading to no video (... Indeed, we saw through a troubleshooting session, conneting that theree different IP partecipants and we have not had any problems at all!).

  Could you please let me know if I am mistaken and C20 accepts indeed default QCIF? ... If Yes, please could you me the command to allow it?

  Thank you very much!

  -Andrea

  You're right C20 QCIF support in the default configuration, and no need to add a special command for him to allow.

  Just for example, below is capset(2) terminal of C20 redefining this as video can be receive and including QCIF with multiple video Protocol.

  ================================================================

  BEGINNING of incoming MESSAGE H245LO-1

  capabilityTableEntryNumber 12,

  capacity receiveVideoCapability: h263VideoCapability:

  {

  qcifMPI 1,.<== support="" for="" decoding="" qcif="" for="">

  cifMPI 1,.

  cif4MPI 1,.

  maxBitRate 20000,

  unrestrictedVector FALSE,

  arithmeticCoding FALSE,

  advancedPrediction FALSE,

  pbFrames FALSE,

  temporalSpatialTradeOffCapability FALSE,

  errorCompensation FALSE,

  h263Options

  {

  capabilityTableEntryNumber 14,

  capacity receiveVideoCapability: h261VideoCapability:

  {

  qcifMPI 1,.<== support="" for="" decoding="" qcif="" for="">

  cifMPI 1,.

  temporalSpatialTradeOffCapability FALSE,

  maxBitRate 19200,

  stillImageTransmission TRUE

  capabilityTableEntryNumber 18,

  capacity receiveVideoCapability: extendedVideoCapability:

  h263VideoCapability:

  {

  qcifMPI 1,.<== support="" for="" decoding="" qcif="" for="">

  cifMPI 1,.

  cif4MPI 1,.

  maxBitRate 20000,

  unrestrictedVector FALSE,

  arithmeticCoding FALSE,

  advancedPrediction FALSE,

  pbFrames FALSE,

  temporalSpatialTradeOffCapability FALSE,

  errorCompensation FALSE

  ================================================================

  Although using QCIF with C20 is little lose capacity C20 power video treatment, but interesting to understand why the software upgrade of Radvision GK introduce one-way video problem.

  Application of C20 log will definitely help to identify or at least limit the first cause of this.

• Cisco TP Codec C20 is not able to speak CEC with LG LCD screens

  I was waiting for the CEC on / stand by the possibilities of the software TC4.2.1 for awhile only discover that it does not work with LG CEC (aka SimpLink), but on the other hand, it works very well with the Sony BRAVIA Sync.

  Has anyone encountered this same problem?

  Hello Mihail,

  We also tested with LG SimpLink and seller sends specific commands and will not respond to requests for confirmation.  This limitation will be added the release notes.

  Thank you!

  Paula

• Upgradation Codec C20

  Hi team,

  We need to upgrade Cisco C20 Codec TC 3.1 version 5.1.7 TC 7.3 since we need to integrate / register with Cisco Call Manager 10.5.1

  Sometime, I have found that if we upgrade from 4.x to 7.x, we need to have the keys to unlocking generated before the upgradation to do and would take about 25-30 minutes for the upgrade.

  Can someone share experience on the same on the backup plan, if possible restoration? Can us directly to TC TC 7.3 3.1.1 upgrade or an intermediate version is necessary as TC 3. x to 4.x and 7.x?

  regds,

  Aman

  You can go directly to the TC7 without problem, simply to take note of various changes from release to release, so be sure to check the date of issue so that you're not caught off guard.  If you upgrade to TC7, you only need a key to unlock for this release, but if you upgrade in stages, you will need a key to unlocking for each major release, that you plan to upgrade to on your way to TC7.

  There is no backup for the TC3 interface, it is quite old, but you could just simply connect to the codec via SSH and take an exit to the xConfiguration, essentially the same that make a backup of the log.  It is easy to roll back once you get to TC7, there is a web interface to swap the image of the software to the previous version, or you can connect via SSH and use the CLI to perform the exchange of software.

  Take a look at c-series-endpoints-software-upgrade-v3-v7 for additional information that will help.

• Codec C20 no led no red.

  Hi all

  I try to do a factory reset on one of our endpoints (profile 42 C20) that I can't connect to it due to authentication failure. Somehow after that I upgraded to 4.1 TC5.1 it resets the root account, but none of the default works or what it was worth.

  While I'm doing the factory reset: press and hold the power button until the led goes red - I it held for more than 90 seconds and does not have red... I tried and tried, and the indicator light on the codec does not red...

  Can someone please help?

  See you soon

  Hugh

  Hugh,

  The behavior has changed in TC5.1. The RED LED lights is no longer, but rather the Green LED flashes. The process is always the same:

  1. Disable the codec.
  2. Press and hold the power until the led on the front in red flashes green.
  3. Release the power button and press the button twice within 5 seconds.

  Thank you

  Paul

• Input audio codec C20

  Hello

  I tried to use the HDMI in the codec (main cam in) to connect to a DVD player I have the video image of the DVD but no sound.

  I have read the Administrator's guide and can not finde any thing about the path of the Audio in the codec.

  One knows if it is not possble.

  Bert-Wietze

  Hello

  Audio for HDMI 1 - C20 is disabled.

  The entrance designated for the camera to the codec C has the audio disabled.

  There is no command for the user to turn it on.

  You will notice this in the title of the form respective product.  Example, for the C20, you see under the video inputs, 1 HDMI input is specified, but under the audio inputs, no HDMI input is specified.

• Cisco Codec C40 remove wallpaper

  Hi all.

  In our installation of cisco telepresence, that we met an interesting question:

  the cisco c40 codec admin created a custom wallpaper, somehow this wallpaper was not appropriate for this codec for 100%.

  After that he transferred the wallpaper on the unit - it restarts. We see a cyclical reboot - boots of unity, we see a cisco logo, then we see a (part of the GUI) overlay on the monitor, after this codec is trying to load wallpaper, fails and went into reboot.

  Are there ways to manually remove this wallpaper of the codec s flash without hard resetting the codec?

  Hi Eugene,

  Try to login as an administrator using ssh/console and run the following command:

  xConfiguration video wallpaper: Summersky

  Best regards

  Sergey Kuzmin

• Cisco Codec C90 with three cameras

  Hi gurus,

  We plugged three cameras to Cisco C90. All cameras are connected with Garland and HDMI cables goes to the codec.

  main camera connected to, a second camera HDMI connected to HDMI 2 and the third camera to HDMI 3.

  Under the video input, we changed the interface of three DVI HDMI sources and the type of PC to the camera.

  Now, I have two problems,

  1. for presentation sharing there is no PC option, is to show only the camera three, DVD camera and document.

  2. Since the touchscreen, we are not able to control the camera 3.

  We were able to control the camera with remote but not with touchscreen 8 three.

  Kindly advise me for more top issue.

  BR

  What is the current version of the firmware of the C90?

  ' 1-presentation sharing there is no PC option, is to show only the camera three, DVD camera and document.»

  -  What input you used to connect to your PC for the presentation? What input connector?

  You mentioned that you have already used a HDMI 3 input for the third camera to allow to use the available video inputs or input 4 (HDMI) or 5 (DVI) for entry-level PC presentation.

  C9.PNG

  

  Log on to the web interface C90 and check the configuration Configuration > System Configuration > video.

  For example, you connected the PC presentation on line 4 (4) using HDMI, as shown in the figure. Change the Type name for PCand PC .

  C90.PNG

  

  "2 - of the touch panel we are not able to control the camera 3."

  -  Check the configuration under your input video n ° 3 of the Source.

  Type: camera

  Under CameraControl:

  CameraId: 3

  Mode: on

  C3.PNG

  

  Kind regards

  Acevirgil

• Upgrade of Cisco Telepresence C20

  Hi guys,.

  one of our clients have reactivated just the service on a video endpoint C20 contract and he asked us to update.

  I was very disappointed by looking at the actual version of the software... 2.0! However, I didn't know any way to update specified on the notes of version... so I just proceeded to the latest version of the software. The upgrade was very well, the system has rebooted and the web interface came online (was it remotely)... but now I'm invited to a user and a password... even if there is no password before the upgrade.

  I tried a few connections by default 'classic': admin\cisco admin\TANDBERG admin\CISCO (also the use of the administrator)... but it still fails.

  The only thing I have not tried is a login "in white" (unfortunately I can't try them now due to a problem of time zone).

  Do you have any suggestions?

  Thank you

  Dan

  Hi Dan,.

  Try with login = admin and password = blank

  After that, if you want to change the password (recommended) click on admin in the right corner and change the password.

  Hope this can help.

  Concerning

  Salim

• Cisco profile series - vs vs C40 C20 C60 codec

  Hi people,

  Is there an online guide that can give me some information about comparisons between codecs c20, c40 and c60 on video profile 42 series systems and why it has such a big difference in the price that is, what have you found to this extra cost?

  Also, is it possible to connect an external projector codec to view the video of the codec on the overhead?

  Thank you

  Hello.

  Yes, it will be possible. You have several inputs and outputs on different codecs.

  The main difference between the C series are physiqueet inputs and outputs and call functions.  See the tables below.

  Models top means more inputs and outputs.

  There are more features than this, but the list shows key capabilities

  	C20	C40	C60	C90
  Resolution	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60
  End to end	720p30 +.	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60
  End to end double-flow	p15 1280/768	1280 × 768 p 30	1600 x 1200 30 / 1080 p 30	1600 x 1200 30 / 1080 p 30
  Output and input physical
  Mic input	2 mini jacks	2 XLR	4 XLR	8 XLR
  Video in	1 + 1 DVI HDMI	2 + 1 DVI HDMI	2 + 2 DVI HDMI	4 HDMI + DVI 2
  		1 S - video / Comp	1 S - video / Comp	HD - SDI 4 component 2
  				1 comp / S-Video
  Video output	2 HDMI	1 + 1 DVI HDMI	1 HDMI + 1 DVI + Comp	2HDMI + 2 DVI + Comp
  MultiSite	NO.	4 way	4 way	4 way
  Resolution

  576 p 30 720 p 30 1080 p 30/720 p 60 Other API API API GPIO GPIO Processing power

  Thank you

  Marius