Cisco ezvpn clinet

Hi all

I have configured the cisco asa 5520 as cisco ezvpn server and cisco 891 as ezvpn client.

the configurtion works fine.i uses client mode on the client side of ezvpn.

but my question is, is it possible to connect to the internal ip address of the ezvpn client side Server ezvpn?

is it possible to do?

and one more thing what is the advantage of the mode of extension of network on the client and how it will work and what are the possible changes that do the client side and the server.

Thank you

Cyril

Here's what you need to change:

No - nat allowed 10.10.10.0 255.255.255.0 10.10.11.0 255.255.255.0

No - nat allowed 192.168.10.0 255.255.255.0 10.10.11.0 255.255.255.0

With the split tunnel, it depends on where you need to access on the client side. If you need to access the client of 10.10.10.200 side, for example, you need to add that in ACL split tunnel. OR if you need to access the entire/24 subnet client side, then you add in the tunnel of ACL split, otherwise, customer return to server traffic goes directly to the internet instead of back to the tunnel.

Tags: Cisco Security

Similar Questions

  • Cisco ezvpn ASAs cannot ping each other inside interfaces

    I have a set ezvpn in place with a 5506 (position B) client-side and a 5520 (location A) server-side. I have successfully connected vpn, and traffic flows. My problem is that I can't SSH in the location b. investigate this more than I can not ping is within the interface of the ASA opposing, or the machines inside each ASA ASA.

    I found the following links that describes a scenario similar to mine, but nothing on one of them helped me.
    http://www.experts-exchange.com/questions/28388142/cannot-ping-ASA-5505-inside-interface-across-VPN.html
    https://www.fir3net.com/firewalls/Cisco/Cisco-ASA-proxy-ARP-gotcha.html
    https://supportforums.Cisco.com/discussion/11755586/Cisco-ASA-VPN-established-cant-ping

    I joined sanitized versions of these two configs. Any help is appreciated.

    Hi Adam

    The site of B I'm not able to see "management of access to inside. Please try to set up the same. He could solve the problem.

    Also on the instruction of the ASA takes place nat can you please try to add keywords 'search non-proxy-arp route'.

    something like:

    nat (inside,outside) source static (Location A)_Networks (Location A)_Networks destination static (location B)-remote_network (location B)-remote_network no-proxy-arp route-lookup
    as I have noted problems with inside access to interface via the VPN when those keywords are not applied. If I remember correctly 8.6.x ASA version had a bug regarding the same. Cordially Véronique

  • All-round Vpn connection with EZVpn

    Hello team,

    Is it possible to configure cisco EZVpn client to start and login before logon on Windows server? Automatically reconnect if the connection has been interrupted?

    The IPSec VPN client is a feature called start before logon that will allow you to establish the IPSec tunnel before Windows domain authentication. The function of self-initiation of VPN client can help with your second requirement.

    SBL:

    http://www.Cisco.com/en/us/products/sw/secursw/ps2308/products_tech_note09186a00807955bc.shtml

    Auto open VPN:

    http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/vpn_client500_501/administration/5vcAch7.html

  • remote router configuration with EzVPN NEM by VPN

    I have the following scenario: Some 836 routers Cisco EzVPN network are connected to a hub VPN 3005 in the main façade.

    The work of LAN-to-LAN connection and I can also telnet via the VPN from a PC to the main façade of a router to a remote site using the address LAN IP of the remote router as a destination. But does not work for example do a "copy run tftp" on the remote router to the LAN of the main façade.

    My questions now are:

    Is it possible to transfer the remote routers configuration file or via the VPN IOS image between the remote router and the LAN at the main façade?

    And, if possible, how do we?

    Thanks in advance

    Mark

    When you make a "copy run tftp" from the remote router, it goes to the source of its external interface TFTP packets, not its interior. The external interface to your local network packets are NOT included in the list of packages to be encrypted, and therefore they lose.

    You must specify the router to the source its TFTP packets from the interface IP address inside, then these will be correctly encrypted and sent through the tunnel.

    The following command should do the trick for you:

    IP tftp source-interface

  • 506th PIX VPN CAAN connect, but no LAN

    Heelo, we have a 506E with 6.3 (3). We want to use Cisco VPN clinet to connect and can do, but cannot ping on the local network or connect to servers... Need help wih configurations because we are novice maybe... Can someone look through the attached config. and see if we have forgotten something... Thank you

    Change your pool outside 192.168.2.0/24.

    IP local pool vpnpool 192.168.x.60 - 192.168.x.63

    Then add an acl of exemption nat for this network.

    access-list sheep permit ip 192.168.2.0 255.255.255.0 255.255.255.0 192.168.x.0

    NAT (inside) 0 access-list sheep

    Then, also change your acl of tunnel from split to reflect the new pool

    permit ip 192.168.2.0 access list SplitTunnel 255.255.255.0 255.255.255.0 192.168.x.0

  • EzVPN between Cisco ASA 5505 (with NEM mode) and Ciscoo 881 Roure

    Hi friends,

    I configured the Cisco ASA 5505 and Cisco router with DMVPN 881. 3 offices works very well but one office remains failure. I did the same configuration for all facilities but this router does not work. Any ideas?

    Please find below the exit of 881 router Cisco:

    YF2_Tbilisi_router #.
    * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:26.793 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:31:26.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:26.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:36.793 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
    * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:31:36.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:36.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 09:31:44.929 4 August: ISAKMP: (0): serving SA., its is 88961 B 34, delme is 88961 B 34
    * 4 August 09:31:46.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:46.793 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:31:46.793 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
    * 4 August 09:31:46.793: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
    * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:31:46.793 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
    * 09:31:46.793 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
    * 09:31:46.793 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
    * 09:31:46.793 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

    * 4 August 09:31:47.805: del_node 2.2.2.2 src dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
    * 09:31:47.805 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 4 August 09:31:47.805: ISAKMP: (0): profile of THE request is (NULL)
    * 09:31:47.805 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
    * 09:31:47.805 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004819
    * 09:31:47.805 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
    * 09:31:47.805 4 August: ISAKMP: (0): client configuration parameters 87531228 adjustment
    * 09:31:47.805 4 August: ISAKMP: 500 local port, remote port 500
    * 09:31:47.805 4 August: ISAKMP: find a dup her to the tree during his B 88961, 34 = isadb_insert call BVA
    * 4 August 09:31:47.805: ISAKMP: (0): set up client mode.
    * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
    * 4 August 09:31:47.805: ISAKMP: (0): built the seller-07 ID NAT - t
    * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-03 ID
    * 4 August 09:31:47.805: ISAKMP: (0): built the seller-02 ID NAT - t
    * 4 August 09:31:47.805: ISKAMP: more send buffer from 1024 to 3072
    * 09:31:47.805 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
    * 09:31:47.805 4 August: ISAKMP (0): payload ID
    next payload: 13
    type: 11
    Group ID: Youth_Facility_2
    Protocol: 17
    Port: 0
    Length: 24
    * 09:31:47.805 4 August: ISAKMP: (0): the total payload length: 24
    * 09:31:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
    * 09:31:47.809 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

    * 4 August 09:31:47.809: ISAKMP: (0): Beginner aggressive Mode Exchange
    * 4 August 09:31:47.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:47.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:31:57.809 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
    * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:31:57.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:31:57.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:07.809 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
    * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:07.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:07.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:17.809 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
    * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:17.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:17.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:27.809 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:27.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:27.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:37.809 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
    * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:37.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:37.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 09:32:46.793 4 August: ISAKMP: (0): serving SA., his is 872E1504, delme is 872E1504
    * 4 August 09:32:47.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:47.809 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:32:47.809 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
    * 4 August 09:32:47.809: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
    * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
    * 09:32:47.809 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
    * 09:32:47.809 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
    * 09:32:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
    * 09:32:47.809 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

    * 4 August 09:32:48.909: del_node src 2.2.2.2:500 dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
    * 09:32:48.909 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

    * 4 August 09:32:48.909: ISAKMP: (0): profile of THE request is (NULL)
    * 09:32:48.909 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
    * 09:32:48.909 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004818
    * 09:32:48.909 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
    * 09:32:48.909 4 August: ISAKMP: (0): client setting Configuration parameters 88C05A48
    * 09:32:48.909 4 August: ISAKMP: 500 local port, remote port 500
    * 09:32:48.909 4 August: ISAKMP: find a dup her to the tree during the isadb_insert his 87B57D38 = call BVA
    * 4 August 09:32:48.909: ISAKMP: (0): set up client mode.
    * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
    * 4 August 09:32:48.909: ISAKMP: (0): built the seller-07 ID NAT - t
    * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-03 ID
    * 4 August 09:32:48.909: ISAKMP: (0): built the seller-02 ID NAT - t
    * 4 August 09:32:48.909: ISKAMP: more send buffer from 1024 to 3072
    * 09:32:48.913 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
    * 09:32:48.913 4 August: ISAKMP (0): payload ID
    next payload: 13
    type: 11
    Group ID: Youth_Facility_2
    Protocol: 17
    Port: 0
    Length: 24
    * 09:32:48.913 4 August: ISAKMP: (0): the total payload length: 24
    * 09:32:48.913 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
    * 09:32:48.913 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

    * 4 August 09:32:48.913: ISAKMP: (0): Beginner aggressive Mode Exchange
    * 4 August 09:32:48.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:48.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:32:58.913 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
    * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:32:58.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:32:58.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:33:08.913 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
    * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:33:08.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:33:08.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:33:18.913 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
    * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:33:18.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:33:18.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
    * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
    * 09:33:28.913 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
    * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
    * 4 August 09:33:28.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
    * 09:33:28.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.

    There is no DMVPN on the SAA. All that you have configured, is not compatible with the ASA or something another DMVPN then. At least debugging shows that there are some EzVPN involved.

    The debug version, it seems that there is no communication on UDP/500 possible between devices. Maybe something is blocking who?

  • EZVPN between ASA and Cisco 2801

    Hi Experts,

    Need help with establishing ezvpn. I have a Cisco 2801 with the following configuration:

    router version 124 - 24.T3 (advanceipservicesk9)

    Crypto ipsec client ezvpn BOS-BACKUP
    connect auto
    Group bosnsw keys clar3nc3
    client mode
    peer 202.47.85.1
    xauth userid interactive mode

    interface FastEthernet0/0
    IP 10.80.3.85 255.255.255.0
    automatic duplex
    automatic speed
    Crypto ipsec client ezvpn BOS-BACKUP inside

    the Cellular0/1/0 interface
    the negotiated IP address
    encapsulation ppp
    load-interval 60
    Broadband Dialer
    GSM Transmitter station
    Dialer-Group 2
    interactive asynchronous mode
    no fair queue
    a model of PPP chap hostname
    PPP chap 0 dummy password
    PPP ipcp dns request
    Crypto ipsec client ezvpn BOS-BACKUP
    !
    IP route 0.0.0.0 0.0.0.0 Cellular0/1/0
    !
    Dialer-list 2 ip protocol allow

    Celuular interface is up and the router is able to ping the exchange of vpn:

    Router # ping 202.47.85.1

    Type to abort escape sequence.
    Send 5, echoes ICMP 100 bytes to 202.47.85.1, wait time is 2 seconds:
    !!!!!
    Success rate is 100 per cent (5/5), round-trip min/avg/max = 396/473/780 ms

    The ASA configuration:

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES esp-3des esp-sha-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    card crypto OUTSIDE_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    OUTSIDE_map interface card crypto OUTSIDE

    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400

    username password encrypted UaV1j04bjTagjYnj privilege 0 bosnsw
    username bosnsw attributes
    VPN-group-policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec l2tp ipsec
    No vpn-framed-ip-address

    type tunnel-group bosnsw remote access
    tunnel-group bosnsw General-attributes
    address BOS_CORPORATE pool
    No ipv6 address pool
    authentication-server-group LOCAL ACS_AUTH
    secondary-authentication-server-group no
    no accounting server group
    Group Policy - by default-BOS_CORPORATE
    No dhcp server
    No band Kingdom
    no password-management
    No substitution-disabling the account
    No band group
    gap required
    certificate-CN user name OR
    secondary username-certificate CN OR
    authentication-attr-of primary server
    authenticated-session-user principal name
    tunnel-group bosnsw webvpn-attributes
    catch-fail-group policy DfltGrpPolicy
    personalization DfltCustomization
    the aaa authentication
    No substitution-svc-download
    No message of rejection-RADIUS-
    no proxy-auth sdi
    no pre-fill-username-ssl client
    no pre-fill-username without client
    No school-pre-fill-name user-customer ssl
    No school-pre-fill-user without customer name
    DNS-Group DefaultDNS
    not without CSD
    bosnsw group of tunnel ipsec-attributes
    pre-shared-key *.
    by the peer-id-validate req
    no chain
    no point of trust
    ISAKMP retry threshold 300 keepalive 2
    no RADIUS-sdi-xauth
    ISAKMP xauth user ikev1-authentication

    BOS-NRD-IT-FW1 # sh cry isa his

    HIS active: 2
    Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)
    Total SA IKE: 2

    1 peer IKE: 112.213.172.108
    Type: user role: answering machine
    Generate a new key: no State: AM_TM_INIT_XAUTH_V6H

    I've attached the output of debugging of router and firewall. Hope someone can shed some light on this issue. Thanks in advance.

    Thats is correct! You must configure the network extension mode if you want to change the IP address

    Here is the guide to configure the router and ASA in network extension mode. Hope you find it useful.

    http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a0080809222.shtml#TS1

    Thank you

    Françoise

  • Router Cisco ASA or IOS may be a SSL VPN clinet?

    I would like to know if the router Cisco ASA or IOS may be a customer of SSL VPN? Thank you.

    I'm glad to hear that.

    Indeed the ASA5505 and Cisco routers can be EzVPN customers.

    Please mark this question as answered if you have any other questions.

    Let me know.

    The rate of any position that you be useful.

  • Cisco 861 ezVPN license remote problem

    I bought a new Cisco 861 SRI with safety advanced on this subject.

    When I look in the Dashboad license in Cisco Configuration professional it tells me I have advsecurity licenses with deployment status 'Deployed' function and the State 'active, in use '.

    But when I want to configure any type of VPN I get the following error message:

    License of technology (advsecurity) associated with this feature is not deployed on this router. Use the link below to deploy the technology license.

    When I click the link I find myself in the dashboard to license again.

    I Don t have another file license and advanced security features should be sufficient for VPN. At least that's what

    http://www.Cisco.com/en/us/prod/collateral/routers/ps380/data_sheet_c78_461543.html said.

    What should I do to be able to configure the VPN?

    Thankx a lot for any help

    Dirk

    What version of CCP do you use?  I see a few other customer cases with this error and it looks like there may be a problem with CCP 2.5.  Customers who use 2.3 CCP do not see this error when applying the license through the user interface.

    Todd

  • Using Cisco IOS Firewall VPN clinet

    Hello

    I configured RTR1 to support VPN Clients. RTR1 has a site 2 RTR 2 site VPN tunnel.

    Customer VPN connected to RTR1 have RTR1 LAN IP connectivity. How can I get the VPN Client LAN to access the local network RTR2?

    I've included the VPN Client LAN to be ecrypted in the VPN tunnel to the LAN RTR2 and Vice Versa. I also tried a static router configured on RTR2 for the LAN of Client VPN IP WAN RTR1 serving of next hop.

    Still doesn't work is not for me. Any ideas?

    Thank you

    The other side added your remote VPN client pool to its configuration? The remote site must know its interesting traffic as well. Is RTR2 NAT'ing? Cleaned the configs for the two routers would help a lot.

  • Cisco VPN router VPN client commercial provider

    Hello

    IM new Cisco VPN technology so please forgive my ignorance.

    I am trying to connect my router to a comercial that support IPSec VPN provider gave me only that here the server ip, user name and password Secret.

    With this information, that I can, for example, to connect with an iPhone using the monofamille in Cisco's VPN IPSec.

    My question is how I put this up directly on a cisco router, or using CCP or config?

    Thanks in advance for all the help/pointers

    with the info given, there are the following config:

    Crypto ipsec VPN ezvpn client
    connect auto
    Astrill key way2stars group
    client mode
    Peer 1.2.3.4
    Astrill-email Astrill-password username password

    Sent by Cisco Support technique iPad App

  • ISA500 site by site ipsec VPN with Cisco IGR

    Hello

    I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.

    But without success.

    my config for openswan, just FYI, maybe not importand for this problem

    installation of config

    protostack = netkey

    nat_traversal = yes

    virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET

    nhelpers = 0

    Conn rz1

    IKEv2 = no

    type = tunnel

    left = % all

    leftsubnet=192.168.5.0/24

    right =.

    rightsourceip = 192.168.1.2

    rightsubnet=192.168.1.0/24

    Keylife 28800 = s

    ikelifetime 28800 = s

    keyingtries = 3

    AUTH = esp

    ESP = aes128-sha1

    KeyExchange = ike

    authby secret =

    start = auto

    IKE = aes128-sha1; modp1536

    dpdaction = redΘmarrer

    dpddelay = 30

    dpdtimeout = 60

    PFS = No.

    aggrmode = no

    Config Cisco 2821 for dynamic dialin:

    crypto ISAKMP policy 1

    BA aes

    sha hash

    preshared authentication

    Group 5

    lifetime 28800

    !

    card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1

    !

    access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255

    !

    Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac

    crypto dynamic-map DYNMAP_1 1

    game of transformation-ESP-AES-SHA1

    match address 102

    !

    ISAKMP crypto key address 0.0.0.0 0.0.0.0

    ISAKMP crypto keepalive 30 periodicals

    !

    life crypto ipsec security association seconds 28800

    !

    interface GigabitEthernet0/0.4002

    card crypto CMAP_1

    !

    I tried ISA550 a config with the same constelations, but without suggesting.

    Anyone has the same problem?

    And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?

    I can successfully establish a tunnel between openswan linux server and the isa550.

    Patrick,

    as you can see on newspapers, the software behind ISA is also OpenSWAN

    I have a facility with a 892 SRI running which should be the same as your 29erxx.

    Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.

    Here is my setup, with roardwarrior AND 2, site 2 site.

    session of crypto consignment

    logging crypto ezvpn

    !

    crypto ISAKMP policy 1

    BA 3des

    preshared authentication

    Group 2

    lifetime 28800

    !

    crypto ISAKMP policy 2

    BA 3des

    md5 hash

    preshared authentication

    Group 2

    lifetime 28800

    !

    crypto ISAKMP policy 3

    BA 3des

    preshared authentication

    Group 2

    !

    crypto ISAKMP policy 4

    BA 3des

    md5 hash

    preshared authentication

    Group 2

    !

    crypto ISAKMP policy 5

    BA 3des

    preshared authentication

    Group 2

    life 7200

    ISAKMP crypto address XXXX XXXXX No.-xauth key

    XXXX XXXX No.-xauth address isakmp encryption key

    !

    ISAKMP crypto client configuration group by default

    key XXXX

    DNS XXXX

    default pool

    ACL easyvpn_client_routes

    PFS

    !

    !

    Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT

    !

    dynamic-map crypto VPN 20

    game of transformation-FEAT

    market arriere-route

    !

    !

    card crypto client VPN authentication list by default

    card crypto VPN isakmp authorization list by default

    crypto map VPN client configuration address respond

    10 VPN ipsec-isakmp crypto map

    Description of VPN - 1

    defined peer XXX

    game of transformation-FEAT

    match the address internal_networks_ipsec

    11 VPN ipsec-isakmp crypto map

    VPN-2 description

    defined peer XXX

    game of transformation-FEAT

    PFS group2 Set

    match the address internal_networks_ipsec2

    card crypto 20-isakmp dynamic VPN ipsec VPN

    !

    !

    Michael

    Please note all useful posts

  • EZVPN - PIX to PIX

    This is perhaps a silly question, but I am at a loss to see what the problem is.

    I have a 515 on my site and am trying to install a few small 501 office across the country.

    Each office can connect and establish a tunnel when I configure use EZ and I a setting up split-tunnel to pass to the Internet or to me every time.

    If for some reason, I have to restart my PIX or my T1 goes down, they lose the tunnel (of course), but they lose also any Internet connection they have. The only way to get them reconnected to the world must go and uncheck the box "use the EZVPN."

    At the end of the day, I don't want to then lose all connectivity when / if I get off.

    What I forget?

    Thanks in advance.

    Robert Crooks

    Network systems administrator

    Ivaco Rolling Mills

    try to add no.-xauth-no-config-mode to your statement of isakmp key.

    ISAKMP key YOURPASSWORD address 192.168.1.2 subnet 255.255.255.255 mask no.-xauth-config-mode no.

    or try to run with this documentation

    http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/products_user_guide_chapter09186a00800898f7.html

  • EzVPN and XAUTH

    A hardware IOS with XAUTH client enabled on the client and the server requests a user name and password, which must be entered manually via cli.

    Is it possible to store the user name and password locally on the client of equipment for xauth phase remaining without the invention of the user? The commands should be used on the client and the server?

    Tanks in advance

    Edgar

    I guess that you have an IOS server also. The "Save password" option in the config of EzVPN has been added to the VPN server in T code 12.3 (2). Note This command is configured on the SERVER, and not on the client.

    The client must be running at least 12.3 (4) T code to support this feature. After you configure "Save password" on the server, you will need to use the manual control on the client to build the tunnel once more. During the negotiation of the next tunnel, the customer is then notified that it is possible to save the password locally. Once this is done, follow this:

    http://www.Cisco.com/univercd/CC/TD/doc/product/software/ios123/123newft/123t/123t_7/ftezvpnr.htm#wp1145535

    If you attempt to save the password on the client, it is enabled on the server, and without having to build the tunnel once more manually so that the customer is on the policy change, you get an error on the client by saying "Cannot save passwords" (or something like that).

  • Between Cisco ASA VPN tunnels with VLAN + hairpin.

    I have two Cisco ASA (5520 and 5505) both with version 9.1 (7) with Over VPN and Security Plus licenses. I try to understand all the internet a traffic tunnel strategy VLAN especially on the 5520 above the 5505 for further routing to the internet (such as a hair/u-turn hairpin). A few warnings:

    1. The 5505 has a dynamically assigned internet address.
    2. The 5505 has sometimes no device turned on behind her, bringing interfaces down to the inside (which can cause problems from site to site).
    3. The 5520 cannot be a client of ezvpn due to its current role as a server of webvpn (anyconnect).

    Let me know if I need to post my current config. Basically, I'm starting from scratch after several attempts.

    Thank you!

    1. The 5505 has a dynamically assigned internet address.

    You can use the following doc to set up the VPN and then this document to configure Hairping/U tuning

    2. the 5505 has sometimes no device turned on behind her, bringing interfaces down to the inside (which can cause problems from site to site).

    Make sure that the interface is connected to a switch so that it remains all the TIME.

    3. 5520 the may not be a ezvpn customer due to she has current as one role anyconnect webvpn ()) server.

    You can use dynamic VPN with normal static rather EZVPN tunnel.

    Kind regards
    Dinesh Moudgil

    PS Please rate helpful messages.

Maybe you are looking for

  • Unable to receive only an email of new mails 2 days ago.

    Thunderbird has worked fine - until yesterday when no new emails have been received - the last of them was dated 12/16. Today started with Thunderbird and nothing more recent has been added (except the same e-mail dated 12/16). When I click on Get Me

  • Why my message a confirmation of reading on a device and not the other?

    I use my iMessage on my iPhone 5 and my Macbook Air, however, sometimes when I send a message from a device it shows a read receipt to the other person on my mac, but not on my iPhone. The message on my iPhone remains as "delivered" much later and th

  • MBP stops when no charging current and 99% battery

    About a day ago, my laptop (13 '' mid-2012 MacBook Pro) stop when I unplugged my charger. I have tried rebooting, but nothing happened when I pressed the power button. I plugged it in, and it began to restart immediately. Since then, the condition of

  • HP Office Jet 8620: Do not print sleep mode

    If I have not used my printer for a while, it goes into mode "Eve".  When working on the computer and try to print something, I always get the message offline printer.  I usually have to restart the printer and then the page will print.  It is a comm

  • Resolution 6570b proBook

    I read that the probook 6570b display is capable of 1600 x 900, but the highest I can choose is 1366 x 768.  It has the graphics card Intel HD 4000.  Am I missing something?  Thank you!