Cisco IP Communicator

Similar Questions

• What version of Cisco IP Communicator supports to UC520?

  Model: UC520

  IOS version: 12.4 (20) T4

  CME: 7.0

  What version of Cisco IP Communicator supports to UC520 with CME7.0?

  Release Notes of IP Communicator is not included CME7.0 in the supported versions.

  http://www.Cisco.com/en/us/products/SW/voicesw/ps5475/prod_release_notes_list.html

  Please advise, thank you.

  Any version.

  However, you must update UC500, because it is very old.

• Cisco IP Communicator with Bluetooth headset has fast battery drain

  Hi all, hoping to exploit the collective knowledge here to find an answer to a question that we live with bluetooth headsets with quickly draining the battery.

  Environment: We run Cisco UCM 10.5 and have some users with Cisco IP Communicator 8.6.4.  Computers are a mixture of office/computer laptop with Windows 7 32/64 - bit.  Most are bluetooth headsets, Plantronics Voyager legend UC with some older models of Plantronics.  These use a bluetooth dongle separated with flag State.  This helmet is announced as having 7 hours of talk time and 10 days standby.  Plantronics software is set to Audio enabled detection and headphones to maintain for PC connection as it is disabled.

  Behaviour: Normally, when the bluetooth headset is not in use, the light blue and the helmet is considered as standby.  When a call, the indicator light is a slow blink showing the helmet is in active use.

  Question: When not in a call, or when the CPIC is even launched, the indicator light is a blue blicking and users can hear 'air' in the helmet, even when not off the hook.  This led the helmet to be in Active mode and thus draining the battery at a higher rate.  Even if option software Plantronics headphones maintain link PC is off, it acts as if it was.  The only way that we were able to work around this problem is in the Plantronics software to disable Audio detection enabled.  This leads to the user needing to press the answer on the headset button and the answer button on the software phone which isn't ideal if users are up and on.

  So having said all this, is there a resolution to allow the headset to use with CPIC without the helmet being still active?

  It comes to video over IP, please move to the appropriate area.

• Compatibility phone Avaya with Cisco Unified Communications Platform

  Hello

  We are currently a user all-Cisco on the side of routing, switching and network security, however, we are a user all Avaya on the phone, IP phone and voice communications.  I laugh with all the problems we had with Avaya and would migrate to Cisco.  My department head wants to know is it possible to have a Cisco platform manage all unified communications and voice mail on the back end, but continue to use the Avaya phones currently in place in each office, until we can replace in the coming years through attrition?  It is essentially a measure of cost that is the main factor in management are unwilling to make any changes whatsoever because of investment is already in the existing system.

  None of the Avaya endpoints are officially supported on Cisco CUCM, but if they SIP phones, they can be defined as 3rd-party SIP endpoints.  That being said you get far more features and satisfaction with phones Cisco CUCM, otherwise ask for another set of questions, and at that time there a seller will point to the other.

• Cisco Unified Communications Applications VMware Tools support

  I have an implementation of vsphere esxi 6.0U2.  Who is the host VMware Tools 10.0.6.

  When the upgrade of all my UC apps (CUCM, CUC, IMP, UCCX *.. it's extraordinary... because it will not refresh), initially, they showed the VMware tools running and updated.  But after a restart of the operating system of each.  VMware Tools is no longer running...

  Anyone can comment/comment.

  doc-wiki such as:

  - http://docwiki.cisco.com/wiki/Virtualization_for_Cisco_Unified_Communica...

  - http://docwiki.cisco.com/wiki/Virtualization_for_Unified_CM_IM_and_Presence

  Indicate that they support ESXi 6.0 and so the tools is surely supported...

  All the comments of someone?

  Anyone else linking 6.0 U2 vSphere, ESXi and pushed its tools to their UC applications?

  Hi Michael,

  I go ahead and prosecute TAC that there are a number of bugs related to the VMware Tools upgrade to any version 10.0. This is a bug in level 2 of gravity;

  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCux90747

  VMware Tools 10.0 update fails on 10.5/11.0 with selinux denials CUCM
  CSCux90747
  Symptom:
  VMware Tools upgrade fails due to various Selinux denials. VI-Client status of tools like is not running, not installed.

• Problem with audio in Cisco IP Communicator

  Hello

  I have a problem with the audio in a VMware View environment.

  I don't know if it's important, but my thin client is a model of WYSE X90LE, and I install the drivers for the USB (property WYSE) support. I use Logitech headset.

  When I connect to virtual desktop, I have a sound; but when I start Ip Communicator application I get the following error: "there is no compatible audio device installed on this computer. "Please click 'OK' to exit the"

  Anyone have this problem?

  Any suggestions?

  Best regards

  Pedro Velasco

  Tarragona, Spain

  You must purchase the TCX rich sound of WYSE. They have three licenses that are required for your virtual machine using Wyse terminals to work properly. Multimedia and USB also. $25 per license per device. You will need to upgrade license TCX, they give you in a MNOS. Ini FILE in your FTP server. I hate this cause that they announce that licenses TCX and an FTP server are needed until you call the problems you are having. I threatened to sue them for false advertising. Also reinstall the VMware tools in the virtual machine. Make sure you have the latest version of the software microsoft RDP. I think they are at 6.1.

• 8.3 (1) ASA Cisco VPN Client and IP Communicator - one-way communication

  Community salvation.

  I have a strange problem with my setup and I'm sure it's either some type of routing (or NAT) or just missing one rule allows traffic. But I'm now at a point where I would like to ask your help.

  I have a few users remote access that have the Cisco IP Communicator (CICC) application installed on their laptops. So:

  The VPN with CPIC user <> ASA Firewall <> router voice <> MAC <> IP phone

  The VPN works fine for all other traffic. The connection of basis for the IP Communicator works well. He get is connected to the CallManager, is shown as registered and you can even call an internal phone and also external phones. BUT: while you can hear the called party (if the phone internal) it does not work for the other direction. There is no sound from the remote/appellant.

  I already understood that it is also not possible to ping from the phone VPN to the internal subnet IP phone. While the VPN user can ping any other device in the network internal, he cannot do for Cisco IP phones. But if the VPN phone calls a phone no-internal (mobile...) - it works!

  My thought is that the call cannot be build up properly between the VPN phone and the internal phone.

  I found similar situations with google, but they are all for the reverse: call for internal works, but not for VPN.

  What do you think?

  Hello

  Usually ASA lists specific to the customer networks VPN Split Tunnel runs.

  This would mean that there is a Split Tunnel ACL used in configurations of the SAA for this VPN connection that needs to have the missing network added to the VPN connection traffic.

  -Jouni

• Wired connection is not displayed in Cisco Connect

  Hello Cisco Home Community Forum,

  All my wireless to my Jack connections are fine and appear in Parental controls in the Cisco Connect software. But my wired connections are not. Each device that connects via an ethernet cable plugged into one of the ports on the router are not included in the Cisco Connect Section of parental controls software. Please tell me how to solve this problem. Or are parent to wireless only controls?

  Thank you for the help

  He won't see the square automatically.list. If the computer is not listed, click Add to select the computer. You can also check the connected devices under the DHCP Client table on the router configuration page.

• Cisco RV180-K9-NA

  URLs how can you block with this router also is it good for games and watching videos or it's just a slow business router for busines stuff?

  Hi internetsspeedster and welcome to the homepage of Cisco community!
  The RV series is managed by the Cisco Small Business support community.
  Discussions on these products, please go here.
  https://supportforums.Cisco.com/community/NetPro/small-business

• Cisco Linksys RV082 VPN router Port Translation

  Hi all

  We have a router RV082 and we try to do port forwarding.

  For example:

  88.123.2.5:80 > 192.168.1.10:2334

  88.123.2.5:81 > 192.168.1.10:2335

  However this does not seem to be possible because I can choose only the source port and IP address of destination unlike the RVS4000.

  Thank you

  These products are processed by the Cisco Small Business support community. Please refer to the URL: https://supportforums.cisco.com/community/netpro/small-business

• Error: "connection attempt timed out, please check the connectivity of the internet" when trying to connect to Cisco AnyConnect 2.5 on Windows 7 x 64 computer with modem usb wireless HSIA.

  Original title: issue with Cisco AnyConnect 2.5 on win 7 x 64 when connecting to the internet using wireless HSIA usb modem.

  I have win 7 x 64 enterprize edition on my laptop.

  I have problems with Cisco anyconnect VPN client. When I'm on my corporate network it works fine.

  But when I connect to internet using HSIA modem usb wireless home form, client AnyConnect VPN will not connect. The error I get is "connection attempt has expired, please check internet connectivity.

  Please help me to solve this problem as soon as possible.

  Hi Manish,

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet forums for assistance.

  I also recommend that you contact the VPN support to help:

  https://supportforums.Cisco.com/community/NetPro/security/VPN

• Problem using Cisco WebEx on Win 7

  I try to use Cisco WebEx to use my home computer to get the files for the school. The meeting is set up at 100%, but whenever I try to access it from my Government computer, I get a saying that an add-on has failed. I tried, but I can't find the add-on responsible and if possible, where to download. The account I have is very, very safe and I'm unable to download a lot of things, so keep that in mind. Spent a lot of time trying to find a Web site that requires no download to use, and this seems to be the best. If there is more better, please let me know.

  < original="" title:="" webex="" from="" a="" government="" computer="">

  Hi Ken,

  Thanks for posting your query on the Microsoft Community.

  With the publication of the description, I understand that you are facing difficulties in the use of Cisco WebEx on your Windows 7 machine. I will certainly help you get this fixed number.

  I would be grateful if you could help me with more information:

  1. what web browser do you use?

  2. are you having the same problem when downloading the thing as Add-ons?

  If the problem only occurs when you use Cisco WebEx , then I suggest you send or post your query on forum Cisco WebEx. You can also check out the link below

  https://supportforums.Cisco.com/community/5726/conferencing

  Hope this information is useful. Please write back to us for assistance, we will be happy to help you.

• Cisco ASA 5500 Series 4-Port GE SSM

  Currently, we have 2 asa 5510 firewall and need to add the

  Cisco ASA 5500 Series 4 - Port GE SSM extension module. Can it be added when the device is turned on and running or the firewall must be turned off to install the plug-in?

  Hello

  You could try to ask this question of the team of firewall, as this page from the community for the physical security and video surveillance.  The team of firewall is located here:

  https://supportforums.Cisco.com/community/NetPro/security/firewall

• How to recover the history of cats Cisco Jabber for Windows?

  Hello

  I have already activated the "enable Instant Messaging" and "allow clients to log instant message history (on customers supported only)" in the messaging application > settings on the CUPS.

  According to my knowledge, the story should be saved in C:\Documents and Settings\home\Local Settings\Application Data\Cisco\Unified Communications\Jabber\CSF\History\.db

  But I can't find the 'History' folder inside the folder of CSF, so it is impossible to find the file db as well.

  Help, please.

  Hello

  Path is as below:

  • XP - C:\Documents and utilisateur\Local Settings\Application Data\Cisco\Unified Communications\Jabber\CSF\History Settings\nom
  • Vista - C:\Users\username\AppData\Local\Cisco\Unified Communications\Jabber\CSF\History
  • Win7 - C:\Users\username\AppData\Local\Cisco\Unified Communications\Jabber\CSF\History

  Thank you

  Ménard

• iOS 10 with Cisco Jabber

  Dear Cisco support community,

  as seen on http://www.apple.com/ipad/business/work-with-apple/cisco/

  Only the spark is described here. There will also be a better integration of the call with Cisco Jabber?

  Spark.PNG

  

  According to me, they're trying to transmit only apple ios 10 best interactive aura to the customer of the spark. This does not mean that jabber for iphone will be less functional in ios 10.