Cisco MX 700

Similar Questions

• Stand-alone configuration of Cisco Aironet 700i

  Hello

  I'm well aware new products Cisco. So please forgive my basic questions.

  I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I don't have a controller. I need to set this up as standalone access point.

  I tried all the basic steps and tried to activate the two radios, but no luck. Anyone can guide me please on how to configure the AP.

  I use web access to configure the AP.

  Help, please

  Thank you

  Sagar

  Hi Sam,

  Please check these messages to set up autonomous AP.

  https://rscciew.WordPress.com/2014/05/24/single-SSID-configuration-on-au...

  https://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on...

  Concerning

  Remember messages useful rates

• AAA Cisco 600 and 700

  Cisco ACS GANYMEDE + AAA can be activated for telnet to Cisco 600 and 700 routers?

  Unfortunately you can not configure radius AAA or Ganymede in routers series 600 or 700.

• Stand-alone Cisco 1040 Mac filtering

  Hello - I'm trying to understand the syntax of the ACL filter by MAC address.

  I built and apply the following:

  access-list 700 refuse a4d1.8cd2.9dce 0000.0000.0000

  access-list 700 allow 0000.0000.0000 0000.0000.0000

  dot11 association-list mac 700

  When this filter is applied to the dot11 radio, reset the interfaces and then no users are connected, or reconnect. When I remove the filter from the radio, users are able to connect again. This occurs if the allowed line is in the ACL list or not.

  What I understand documentation Cisco ( http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan... ) it's the correct syntax, however it seems to block all the associations to the AP, even if the last line is a permit all.

  Any help is appreciated.

  access-list 700 permit 0000.0000.0000 0000.0000.0000

  Above the line needs to be fixed as follows

  access-list 700 permit 0000.0000.0000 ffff.ffff.ffff

  Try it and let me know HTH Rasika * Pls note all useful responses *.

• 14.3.1 TMS version and Polycom 700 series group

  Hello world

  I just wanted to know if the TMS version 14.3.1 lets add Polycom group series 700 as a breakpoint or not.

  Here to talk, it shows an error of unsupported Type System. Not sure if this is a bug or compatibility issue. I was wondering if any document matrix compatibility is available for it or not.

  I greately appreciate your help.

  Thank you.

  Rgds,

  Bushra

  Not supported. However, and as with any other system not directly supported in TMS, you can add it as a 'House' system in the TMS.

  Sent by Cisco Support technique iPad App

• integrated macOS Sierra Cisco IPsec VPN does not work anymore (impossible to validate the server certificate)

  Hello

  I just upgraded to macOS Sierra and built-in Cisco IPsec VPN no longer works. When you try to connect, I get a "cannot validate the certificate of the server. "Check your settings and try to reconnect" error message. I use Cisco ASA with self-signed certificates and everything worked fine with previous versions of OS X.

  Please help me, I need my VPN Thx a lot

  I am having the same problem with StrongSwan and help cert signed with the channel to complete certificates included in the pkcs12 file imported to the keychain. It was working properly in El Capitan, but now broken in the Sierra.

• Cisco VPN does not work in the Sierra

  I just upgraded to OS Sierra and the Cisco VPN, I had the installer does connect more.  The Setup looks right into network preferences. When I click it looks like it is trying but stops without asking for a password.

  Cisco VPN client may need to update or re-installed. If she uses the PPTP Protocol, it will not work. Support for PPTP was ignored, because it is no longer considered as secure.

• My MacBook Pro was built in mid-2009, I understand that I won't be able to get the next Sierra of OS.  I just put a new hard drive 700 GB, more I added a new battery to include a new CD/DVD drive.  I spent more than 400 million dollars. What I need to by

  My MacBook Pro was built in mid-2009, a 2.6 GHz, 13-inch, I just put a new hard drive 700 GB and I added a new battery to include a new CD/DVD drive.  I spent more than 400 million dollars.

  I understand that I won't be able to get the next Sierra of OS. I need to by a new Mac?

  Talk to the people the more I would get if I turn in I'd get is about are about $ 100 million.  Please tell me it isn't so.

  If you want Siera you will need a new Mac, but you can continue to use the old one as long as you want.

• Cisco Jabber

  Good afternoon; I have the Cisco Jabber Software running on an Iphone 6 Plus, everything works well when the phone is unlock, when the phone is locked can not answer the calls received by the Cisco Jabber only a window appears with a message that I have a call, but I can't answer. Is there a way to solve this problem. ????

  Greetings.

  Fernando

  Since this request is not an Apple application, I suggest make you contact with the developer of application or their support and ask your question.

• If I can do an Airport Extreme mobile network with a modem/router cable xfinity manufactured by Cisco?

  Can I create an Airport Extreme (current generation) network of roaming with a cable modem/router xfinity manufactured by Cisco (DPC3939 to be exact)?  The modem-router Cisco/Xfinity put into bridge mode?

  Can I create an Airport Extreme (current generation) network of roaming with a cable modem/router xfinity manufactured by Cisco (DPC3939 to be exact)?

  Yes, if the Airport Extreme will be connected to the Cisco DPC3939 back using wired Ethernet wired, permanent.

  The modem-router Cisco/Xfinity put into bridge mode?

  No. I you have done this, the Cisco/Xfinity device would only act as a simple modem... so it would not be a wireless service to all.

  A note of caution here... the support document you are referencing... Wi - Fi base stations: install and configure a roaming network (802.11 a/b/g/n)... use the examples that are long outdated does not follow with the versions present on a Mac AirPort Utility or iPhone/iPad.

  There are some good general information in the document.

• Is it possible to download a previous version of firefox that latest update blocks the characteristics I absolutely have to have for my cisco courses?

  I can't get my password box or my java tool correctly load or work on the update for firefox java tool is something that I have to complete my work in my cisco course. So I would like to know if there is a way to download and install an older version of firefox, so I have something I can do my job without having to use a browser that I don't have confidence.

  If you decide to try the version Extended Support Release (ESR) of Firefox, here is how I suggest to install:

  Clean reinstall it

  We use this name, but it isn't about deleting your settings, this is to ensure that the program, files are clean (not incompatible, corrupt or exotic code files). As described below, this process does not disrupt your existing settings. Don't uninstall NOT Firefox, that does not need.

  (A) download a fresh Installer for Firefox 38.2.0esr of https://www.mozilla.org/firefox/organizations/all/ in an ideal location. (Scroll down your preferred language).

  (B) the release of Firefox (if any).

  (C) to rename the program folder, either:

  (Windows 64-bit folder names)

  C:\Program Files (x86)\Mozilla Firefox
  

  TO

  C:\Program Files (x86)\Fx40
  

  (Windows 32-bit folder names)

  C:\Program Files\Mozilla Firefox
  

  TO

  C:\Program Files\Fx40
  

  (D) run the installer downloaded to (A). It should automatically connect to your existing settings.

  Install and run?

  Note: Some plugins can only exist in the old folder. If it is missing something essential, present in these files:

  • \Fx40\Plugins
  • \Fx40\browser\plugins

• FireFox 39 Incompatible with all Cisco devices

  With the last update access to all devices Cisco via FireFox is no longer supported. Now, I get the following errors:

  The secure connection failed
  An error occurred during a connection to [IP]. SSL has received a low ephemeral Diffie-Hellman key in the handshake message exchange the server key. (Error code: ssl_error_weak_server_ephemeral_dh_key)
  The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
  Contact the Web site owners to inform them of this problem.

  Is there a way to roll back the version to avoid this or a permanent fix? FireFox is currently the only browser that works very well with Cisco devices, and now it won't work at all.

  What happens if you set these false in two: config:

  Security.SSL3.dhe_rsa_aes_128_sha
  Security.SSL3.dhe_rsa_aes_256_sha

  Are you able to connect with disabled ciphers?

• I have a large address book (1,700). I want to send an email to everyone except 50

  I have a large address book (1,700). I want to send an email to everyone except 50 - and these 50 are in their own list. Y at - it a tip/trick to remove them?

  Thank you
  Patrick

  Well, I think that the answer to your question is 'no '.

  But I wonder how you intend to send to the recipients of 1700. Thunderbird will not let you send a message to as many addresses in one fell swoop, and I suspect that your email provider might be objected too.

  I suggest that consider you a merge and merge, which would create discreet messages from 1700, but then your main problem will receive relevant addresses of 1700 (minus 50) in a proper file.

  And I must say that the merge module and direct mail to Thunderbird is somewhat fragile, and I would direct you instead to free agency and its built in fusion facilities, or a service like Mailchimp.

• Is the plugin "OpenH264 video Codec provided by Cisco Systems, Inc." supposed to come with firefox?

  I recently reinstalled Firefox on my computer and now there is a plugin called "OpenH264 video Codec provided by Cisco Systems, Inc.". I've used Firefox for some time and have never seen this. -What is that supposed to be there. It come with the download of Firefox now?

  Hello DuckBilledPlatypus, yes it is a legitimate plugin that was introduced in firefox 33. for some technical experience on this subject, please see: http://andreasgal.com/2014/10/14/openh264-now-in-firefox/

• What is the best way to copy the 700 lots of e-mail files to a new computer?

  I'm moving my wife and an old (Thunderbird, Win XP) computer to a new computer (Thunderbird Win 7). It has about 700 local folders with thousands of emails in them. What is the best way to copy to the new computer?

  The easiest is just to copy the whole profile.

  Menu help > troubleshooting information

  Close Thunderbird

  In windows Explorer, select all and copy.
  just stick on a thumb or other portable media to read/write (not the CD or the DVD)

  on the new Machine to repeat the troubleshooting and close the steps to get the current profile folder

  This time all the portable media stick in the profile to replace what is there

  Open Thunderbird, your additions of e-mail contacts does it all