Cisco SX80 removing 'no camera not connected' OSD warning

Similar Questions

• Need help - camera not connected in Tandberg 6000 MXP

  Hello

  After connection to the tandberg 6000 mxp codec HD camera, I get message camera not connected.

  There is no speicial cable to this code? and what is the axis of the s-video on the codec that mark as "'primary' cam?

  Thanks in advance

  Shy

  Camera cable aboard MXP is similar, but it does not work with 6000 MXP codecs. I assume that your cable is marked with C3000 (works only with Edsge and 3000 MXP codecs). You need the cable marked with C6000. I don't know the SKU of CISCO for this cable. It may help you reference TANDBERG:

  115420 camera HD t6000s cable, 2 m

  115421 camera HD t6000s cable, 5 m

  I hope this help you!

• HD Lifecam Softwaew charges but camera not connected message

  I tried to use the new lifecam HD on a new laptop of Dell Studio 1555 with 4 GB, 2.4 GHz dual core, a lot of disk space and last Vista 64-bit.

  The software loaded and I connected the camera when told too, not before. Loads of software 3.0, but when it starts it says that there is no camera connected. Rebooted, tried different ports USB etc. No luck. I've never had a Logitech camera on the laptop.

  I checked the drivers via the control panel and the hardware and the driver have load/activated and no material error.

  I tried the camera on the desktop Vista 32-bit, 4 GB, 2.4 GHz (dual-core) with the same results, although once the recognized but camera performance was very poor in terms of speed in HD. After a reboot, I got the error of the device not connected.

  I returned the camera to Frys and they managed to get the camera running with authoring software (I don't think it was the HD).

  Anyone know what the issuance or the corrective action?

  Dave

  The problem is that you may have installed the wrong drivers and it was not to recognize the camera that he was trying to find the camera that was compatible with the driver you have installed.

  All the best!

• Camera not working - seems to have disappeared?

  Hello - I searched for this question but couldn't find answer to my question. I get the message 'no camera not connected' when I connect to Photobooth and tried "sudo killall" stuff but keep not getting the error "no matching found process."

  I then had a glance system information and under camera, it says "no video capture devices found '.

  My camera has been removed? My son pulled the macbook on the floor the other day and I thought that he had escaped unscathed but wonder if he has fucked the camera?

  I'm on a retina Pro 15-inch early 2013, 2.7 GHz, 16G if this is helpful to all.

  Thanks in advance!

  One of them will solve your problem of camera:

  (1) If your Mac restart does not solve the problem,

  (2) use http://support.apple.com/kb/HT2090 from Apple.

  (BTW - troubleshooting section called an "iSight" camera.  However, after that article was published, Apple has changed the name of the built-in camera on the recent "iSight" Macs "FaceTime", then "FaceTime HD."  Whatever the name of your built-in camera, the same info and troubleshooting applies.)

  Be sure to test several Apple app (photo booth, FaceTime, iMovie, QuickTime Player, etc.) in more than one user account.  Do NOT use the 'Guest' for this test account.  If you don't have more than one user account for testing, create one now.  If you need help, how is explained in http://support.apple.com/en-us/HT201754.

  A 'Standard' user account is all you need for the tests.

  (3) If your camera will work correctly even with Apple applications, use OS X Recovery to completely reinstall your Mac OS since system recovery stored on your startup disk.  Don't bother test Skype or other 3rd party apps until you have your camera works with applications Apple.

  (4) If none of the suggestions above resolve your issue, contact Apple or one of the Apple-Authorized Service Provider to have your Mac professionally repaired. Don't forget to back up your Mac and Deauthorize iTunes before the call for tenders for the service.

  MrsLister wrote:... Information System says "no video capture devices found '...

  Lack of Information system to recognize your camera is normally an indication of a hardware problem.  There is no serviceable parts by the user of the camera to the Mac.  With the help of equipment, contact one of the Apple-Authorized Service provider or Apple for service.

  Post edited by: Jim EZ

  Mac OSX 10.11.3

• Problem of built-in webcam. He says always "not connected".

  Hi, I bought a new Sony Vaio VPCCA series and when I got it, the webcam was working fine and then I started to use it with facebook videocall and it was fine, but the next day when I went to use it again, it said no camera not connected. My friend already looked and found that there is an unknown device that has been incorrectly installed then it uninstalled and then relaunch the software for the webcam. But then the next day it happened again, now the problem is that whenever I have uninstall so-called usb device that was not properly installed and executed the quiet software of webcam reboot the computer, it does everywhere again. The thing is restarting the laptop each time it will say "software device driver is not properly installed" and is I click on it it says is a USB device when there is no USB device connected to the laptop? So how could he say that? Please help me, this problem has been bothers me everyday and I really need the webcam, which was one of the reasons why I bought this laptop. Help, please!

  Hello

  1. what operating system do you use?

  2 did you change on your computer?

  If you use windows7, I suggest you to follow the links and check out them.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  What to do when a device is not installed correctly

  http://Windows.Microsoft.com/en-us/Windows7/what-to-do-when-a-device-isn ' t-installed-correctly

  I also suggest you to contact the center of support of sonny and check.

  http://eSupport.Sony.com/Perl/select-System.pl?PRODTYPE=1, 24,26,66,9,70,5,72

• Connection of third-party cameras Cisco SX80

  Is it possible to connect any third party camera Cisco SX80.  I'm looking to plug pregnant vaddio Auto Trak 2.0 camera to the Cisco SX80 instead of the Precision60 or speaker track monitoring cameras.

  We use third-party cameras (Sony) with all of our SX80, however, they must be controlled by a third party such as AMX system. Works very well for us - however, none of us is "followed by speaker.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Overheating of Cisco SX80 double camera

  We have a SX80 Cisco codec with dual cams installed at the front of the room who the speaker / auto track feature. This room was originally installed about 1 year ago. And just recently, I started to notice some flickering with capture our video cameras in the room of the VTC. In addition, the Auto Track feature pans and zooms to an individual speaker during a video call no longer works and manual tabs on the touch screen to control the cameras are inoperable as well.

  At this 1st, it was just the flickering I noticed and I simply unplugged feeding on both cams for a little to solve this problem. However, a week later... twinkling is back, but now came the problem with the Auto Track and manual controls for each input. After power to the Assembly of the whole camera to mount on the front of the room for about 30 minutes, it seems to solve the problem. But now again once this morning the Auto track does not work and the emission of heat from the base that the cameras are on is very hot.

  I've determined that the power that feeds on the Assembly of the camera at the front of the room is separated BC from the system of room in other words, when you stop AV system of the room through the touch screen, it is always power supplied to the Assembly of the camera with a separate. What has power constantly running on the cams, making them HOT.

  Has anyone else had this problem with the Assembly Speaker SX80 track? And if yes, what is the resolution other than intermittently, turning them off the coast from time to time. I know that this device is relatively new, so wonder if the circuit design within the frame of the Assembly of the camera is shotty and needs reworking.

  Thanks in advance!

  Check out this link. It explains your problem

  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCuu06180

• Satellite Pro L650: cannot use Skype - cam and microphone are not connected

  Having problems connecting to Skype.
  It seems that the microphone and web cam are not connected.
  Skype self-test will not respond with the voice test.

  Hello

  Have you checked the Skype settings?

  There, you should check if the right microphone and the internal webcam have been chosen.

  By the way: is the webcam properly recognized in Device Manager?

  You can use the webcam using the preinstalled software webcam?

• Re: Installation Canon IXUS V - connection of the camera not detected

  I installed the driver from the website of Canon, but when I connect the camera, I get a message saying "connection Camera not detected' followed by an error message saying pscN109 has stopped working.

  Then a message from Microsoft saying no soloution found. Can someone help me?

  Hey Buddy

  May I ask why you post this message here on the forum of Toshiba?

  I think you should contact the manufacturer of the device for support

• Application that created on another computer will not connect usb-camera

  Hello, friends!

  I have a problem:

  My application that was created on my computer does not connect usb-camera on the other computer. I installed the LabView run-time engine and the runtime of vision on this computer but it is not useful :-(application is open, but the usb device not running.

  I'll be thanked for any help with this problem!

  Thank you very much!

  It's the solution to the problem:

  Solution:
  To run an exe containing NEITHER-IMAQ for USB functions, follow these steps on the computer that is running the EXE file:

  1. Install the following execution engines:
     • LabVIEW Run - time Engine (same version that was used to develop the VI)
     • Execution of vision engine (same version that was used to develop the VI)
       • One Vision single-seater deployment license is required for each computer target on which you install the runtime of the Vision. See all the related links for more details.
  2. Copy the following dll files to the directory on your development computer system, usually C:\Windows\system32 directory of your target machine system.
     • ImaqDirectShowDll.dll
     • ImaqDirectShowExport.dll
  3. Register at ImaqDirectShowExport.dll by the Windows Start Menu , click run. Type regsvr32 C:\WINDOWS\system32\ImaqDirectShowExport.dll, and then click OK to register the DLL.

     If you are on a different operating system or if the system folder is different and that you want to copy the path instead of typing all the way, you can drag the file to the command line at the prompt to run it, highlight the path, right-click and select it copy.  Paste in the command prompt by right-clicking and selecting window block.

     The ImaqDirectShowDll doesn't have to be registered.

  Once these steps are completed, and the DLL is registered successfully, your EXE will work.  Vision Acquisition software or Vision Development Module must be installed on the target computer.

• The user * address email is removed from the privacy * could not connect, could not access the directory.

  For the second time in the last two weeks going through my event logs, I noticed several hundred newspaper failed attempts at the course over a period of twenty minutes.  they are random user accounts that don't exist not user 1, user 2, www., or just names at random, the papers say newspaper caused by a wrong password or account.  "the first of these events several connected has this message:" user * address email is removed from the privacy * could not connect, could not access the directory. ».  What does that mean?  Do you need access and control my computer?  Any info would be a great help.

  Looks like someone trying to log on your computer.  Check your firewall settings to make sure that they can't.

  Visit https://www.grc.com/x/ne.dll?bh0bkyd2 the site "shields up" to perform a check.  Some people to dismiss the guy who runs it, but the test doesn't show you which allows your computer to the world to see.

• Internet not connected during the installation of life Cam 3.0

  Original title: when I try to install my new life Cam 3.0

  He says that I am not connected to the internet and try again later. BUT I am connected and tried disabling my firewall, nothing works... Please help me, I'm windows xp2

  Hello

  1. What is the accurate and complete error message that you receive?

  You can try the troubleshooting provided in the links below steps to fix the problem.

  Troubleshoot installation of Intellipoint and IntelliType LifeCam software

  http://support.Microsoft.com/kb/953691

  Troubleshoot failures to find the new LifeCam hardware

  http://support.Microsoft.com/kb/929087

• I have a laptop with Windows XP. After getting a virus, I scanned with AVG and removed the threat. After re-booting, I can not connect to wireless internet.

  I have a laptop with Windows XP.  After getting a virus, I scanned with AVG and removed the threat.  After re-booting, I can not connect to wireless internet.  The icon shows "acquiring network address".  I connected the router directly on laptop computer connected to the wireless network and still unable to connect.  I tried to restore the system as well, but the message says "unable to restore the system, no changes were made.  Help?

  original title: acquisition of network address

  Hello, Steve.

  Try this link below on how to reset IE and let me know if it helps.
  http://support.Microsoft.com/kb/923737

• the digital camera driver does not load when a sony camera is connected to the computer vista laptop.

  At the same time the downloaded movies netflix has more audio.  Device Manager does not display a driver of the camera when the camera is attached via firewire and running?  I tried to reload the drivers and worked with the pilot web-based updates.

  Hi mstradt,

  1. which version of the operating system are you using 32-bit or 64-bit?

  2. What is the model of the camera number?

  3. you try to use the camera of Sony for the first time?

  4. How do you try to connect the camera?

  You can first try connect the camera with the different port and check if it is detected.

  Also try to use only Sony 4 firewire cable 4-pin to connect the camera.

  You can also visit the following links and see if it helps:

  Can what types of connections and digital video cameras be used to import video?

  http://Windows.Microsoft.com/en-us/Windows-Vista/which-types-of-digital-video-cameras-and-connections-can-I-use-to-import-video

  Troubleshoot camera connection

  http://Windows.Microsoft.com/en-us/Windows-Vista/Troubleshoot-camera-connection-problems

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• My camera SonyDSC-S85 will not connect to windows 7 said no driver available, why go to this if it does not support my equipment

  My Sony DSC - S85 will not connect to windows 7. He said no driver is available I can't believe what is happening simply because do upgrades of windows I yo buy all new appliances and video equipment.

  You're right - the site of Sony says that your camera is not supported under Windows 32 or 64-Bit 7. However there is a simple solution - take the memory stick in and out of the camera and a card reader allows you to transfer your photos to your PC.

  If your PC does not have a card reader, you can buy USB very cheap ones. Just make sure it's one that can read the memory stick into your camera.