Cisco telepresence sx20

Similar Questions

• Cisco TelePresence SX20 + VCS 8.2 Server and Skype for business 2015

  Nice day! My name is Dimitri! Have Cisco TelePresence SX20 + VCS 8.2 Server and Skype for business 2015. Is it possible to set up a conference call SFB and appeal to all subscribers of this conference? At present, we can only call on a single client and SFB. We have the current version of the software TCNC5.1.4.295090 SX20 - is it possible he obnoviti 7, and it will help to improve the situation? Thank you!

  I'm no expert on this technology, but I have some idea and already deployed some projects dealing with the integration of Cisco (CUCM, VCS) video infrastructure to Microsoft video infra like Lync. It would be the same process to make it work in your case.

  How does your deployed SFB? How do you do a conference for audio and video, participants can join the conference by dialing?

  • Mediation server would be required as a front-end server for you to integrate IP/PBXS using SIP trunk to enable voice (audio) Conference with the participants to the PSTN.
  • AVMCU Should be (Audio video Multipoint Conferencing Unit) will host the video conference that will include video endpoints as participants.
  • Video of Interop (SCREW) Server would be required to interface your SFB to third video conference infrastructure such as Cisco UCM or VCS for the endpoints Cisco call client SFB of endpoint of Cisco to participate to the conference organised on SFB by dialing the conference number.

  I'd say contact your AM SFB or Support as well for queries about how to plan your infrastructure SFB and direction.

  Kind regards

  Acevirgil

• Cisco TelePresence SX20 with laptop

  I use a Cisco TelePresence as autonomous SX20 endpoint configured with a public IP address (in Pakistan). I want to connect a portable computer (to Canada) to start video conferencing using the portable camera. Please advice me the software to install on the laptop so that I can start with my SX20 videoconferencing based on IP configured on my SX20.

  To understand kindly refer to the disposal of partner network.

  Please help me its urgent.

  Hello

  www.ciscojabbervideo.com

  BR Oleksandr

• Cisco Telepresence SX20 and Touch 8 Configuration after paired

  Hello

  I successfully connected and combined the SX20 Cisco's Telepresence and Cisco Telepresence Touch 8. Before using the 8 key, we used the remote control instead. As a result, I have two questions about this.

  1. as far as I know, when I use the 8 key, the remote control cannot be used. Is it possible to use both of them?

  2. How can I change the background of my SX20 touch 8? Previously, the remote I can easily choose the background for my SX20. But after pairing with Touch 8, background in my SX20 become a blue large clock. I really want to have a different background but cannot find the way how to change.

  Any help would be appreciated.

  Thank you.

  Sincerely,

  Bagus Hanindhito

  After you connect the 8 Touch, you can still use the remote control, you will need to put on the SX20:

  SystemUnit MenuType experimental configuration: full

  I think that the standard background when using a touchscreen device is what you see, blue with large clock.  However, after the MenuType return in full which will give you the full OSD which is used with the remote and not that of the button, you may be able to change the background then.

• Double screen in Cisco Telepresence SX20

  Hi all

  I have a recently installed SX20 units which are registered on a VCS. the unit has the following options installed.

  NaturalPresenter / MultiSite / PremiumResolution / DualDisplay

  When I make a call to another site and I m send a content, I´d like to see on the screen on the left side in full screen the remote site.

  And on the right screen, I need see what I m sending.

  Anyone know how to make this configuration?

  You suggest you have a look on the Administrator's guide, choose the one corresponding to the version of software you are using: http://www.cisco.com/c/en/us/support/collaboration-endpoints/telepresence-quick-set-series/products-maintenance-guides-list.html

  Go to control panel, category "Vidéo", "monitors:, select 'Dual' or 'DualPresentationOnly'. '. See screenshot below:

  SX20.gif

  

  Go to the video output and output hdmi 1 and hdmi 2 value what configuration you need. monitor i.e. first, second, presentation only, see the screenshot below:

  .

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• On Cisco telepresence SX20

  Hi telepresence Experts.

  When I connect my laptop with the sx20 and click on 'call tab control' a message presented in the two screens of the laptop. The message is "Snapshots require the option RemoteMonitoring key. Would you tell me the reason and function of 'Ctrl tab call' please...

  Thanks in advance.

  Concerning

  Nizam

  Suggest you take a look at the admin guide - page 10 shows you from everything about the web interface.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Integration of the Cisco Telepresence SX20 with Cisco Telepresence EX60

  Hi all

  I have a question, I have the following device:

  -SX20 together

  -EX60 with touchscreen controller

  Do I know if the EX60 can be deployed in an environment SX20? as each of them as functions of call I don't know if it will be in conflict or not because I have little knowledge about the voice and video. If the device can be integrated, can I request a deployment guide, the configuration guide on these? Thank you very much!

  If your devices are not connected to any call (VCS or CUCM) control, search for SX20 autonomous in the forums - there are many threads that describe what you need to configure the settings.  Do the same configuration on the SX and exodus once this is done, you should be able to call the IP address of one of the other.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Ways to receive calls from address book on Cisco Telepresence SX20?

  I got many unknown calls on my teleconferencing equipment and I would like to know if there are ways to block these calls or even perhaps only to receive calls on the address book.

  This has been discussed before in the forums many times more.  Take a look at some of the following threads:

  • nuisance-h323-call-sx20
  • Ghost-calls-tandberg e20
  • sourceh323idcisco-incomingcalls
  • VCS-sip-abuse-reported

  If your endpoint has a public IP address, depending on the configuration of endpoint, you could get behind a NAT device or restrict access of your firewall to allow only specific IP addresses this conference you with.  If you use H323, you must also disable SIP endpoint.

• Cisco Telepresence SX20 H323 autonomous "no video call.

  This system can receive calls IP to external systems. But when I dial to test outgoing calls (IP calls) see the other side of the call to come and he received but no video/audio on their side. On the side of the appellant, I receive the following message if poster on the screen "no video in" then the call ends. The only messages in the log are below.

  Log messages:

  WARNING: Default call Protocol

  The default call protocol is set to H323, but the system is not registered on this Protocol. The system isn't able to make all the calls. Please change the default call Protocol, verify that Protocol is enabled, or check the configuration of H323.

  Caution: setting up an IPv6 address

  The IPv6 address configuration is statically defined for an invalid address (or mask, gateway or subnet). Enable the DHCP, or enter a valid static IPv6 assignment

  Oh yes, whenever you deal with video, any type of inspection of the firewall must be disabled because it could cause a delay or simply no video sent/received.

• Configure Cisco Telepresence SX20 to use H323

  The engineer back a configuration a model for this unit. Because SIP is not used by the seller which we will be conferences with I have to configure this device in the call manager to use H323. Can someone guide me where in Call Manager I can install this device to use the H323 Protocol.

  CUCM is SIP only, if you need make a H323 call. You will need to either Setup of endpoint without CUCM self-sustaining, as Acevirgil mentioned, however it isn't bigger than its configuration already with CUCM. The other alternative is if you have a VCS or highway, or of those who can ensure Interworking using SIP to H323 and vice versa.

  Do you know why the other side can't H323, is there a way to ensure the interoperability of H333-SIP calls?

• Is any impact of a change of the password of the local user account on an instance of a content server Cisco TelePresence virtual computer?

  Hello

  I'm looking to see if there is an impact to change the password of the local user account on an instance of a content server Cisco TelePresence virtual machine?

  The software version is v6.2 build 4073.

  Thank you in advance,

  Robert

  I'll assume, you are referring to the administrator account, but it can be applied to any local account which is located on the TCS server itself.  It has no impact to change the password, unless you are using doesn't say account to connect to the server of TCS or web interface, it will not affect the application of TCS as most things such as external storage or clustering rely on domain accounts and not the local server.

• Driver of Cisco Telepresence - room LoopBack

  Hello world

  Is it possible to create a meeting room on Cisco Telepresence driver that will return the video to the appellant alone in the room? As the [email protected] / * / Cisco's Sip URI? (A kind of selfview room)

  Thanks for your help.

  It is possible to show only one participant connected to a MCU conference selfview, but not for telepresence Server conferences.  It comes without caring if the driver is involved or not.  The service provided by Cisco closure is obtained with the C40/60 endpoints where the audio and the video plays in a loop directly to the connected call (output HDMI to HDMI-in, output audio RCA audio-in RCA/RCA).

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• Cisco TelePresence Manager version 1.7 does support Windows Small Business Server 2008?

  Hello

  Is Microsoft Windows Small Business Server 2008 supported the Protocol LDAP, AD and MS Exchange server for Cisco TelePresence Manager version 1.7?

  Thank you

  AA

  Hello Ahmed - although this configuration "can work", Windows 2008 Small Business Server is not on the support list. This means that it has not been tested and it certifies to work with telepresence.

  To my knowledge, he's not on the roadmap for the future support however, I search and repost as soon as I have an answer for you.

  Kind regards

  -Andrew

  Sent by Cisco Support technique iPhone App

• Activation of presence on the web setting in cisco telepresence SX-20

  I have EDT cisco telepresence SX-20 devices, want to allow the web presence but the poster ' mistake: it will be changed setting OSD "guid .pls myself

  What setting exactly are you trying to change?