Cisco VPN 3000 at work and at home

Similar Questions

• After the upgrade yesterday from Vista to Windows 7, now my Cisco VPN does not work and I get an error message titled: grounds 440 driver fault. Any ideas to fix this?

  After the upgrade yesterday from Vista to Windows 7, now my Cisco VPN does not work and I get an error message titled: grounds 440 driver fault.  Any ideas to fix this?

  This was the solution!  The works of vpn as $ 1 million now.  I followed the instructions above to enter the uninstall program and selecting the repair option.  I rebooted the machine, then used the troubleshooting on vpn software compatibility option.  Selected Windows windows xp (service pack 2) as the correct software and cisco vpn client started right up.

  Thanks, Nick!

  Rick

• Console Cable - Cisco VPN 3000 Concentrator

  Where can I get a cable from the console to the Cisco VPN 3000 Concentrator? The place I bought the hub of not sent me one with it.

  Thank you

  JP

  JP,

  Console port for the concentrator vpn being complient rs-232, you can buy two female DB9 to RJ45 / adapters, one for the concetrator and one for the PC to use in the COM1 port, then use a regular straight through CAT5 cable, that's the way I do and it is convenient as suppose to use the straight through serial rs-232 cable.

  http://www.sealevel.com/product_detail.asp?product_id=787

  With regard to the regular cable this hub comes with you can use it.

  http://www.stonewallcable.com/product.asp?Dept%5Fid=35&PF%5Fid=SC%2DS9%2DFF

  Adidtional information for your initial hub seup -.

  http://www.Cisco.com/univercd/CC/TD/doc/product/VPN/vpn3000/3_6/getting/gs2inst.htm#1050260

  Concerning

  PLS rate useful posts

• How many licenses are delivered with the suite? We must be able to connect at work and at home.

  How many licenses are delivered with the suite? We must be able to connect at work and at home.

  A single user license allows you to have two active facilities, in order to have a home and place of work or on a laptop or any other functional scenario where you have two computers with the software installed and activated is allowed.

• Cisco VPN does not work in the Sierra

  I just upgraded to OS Sierra and the Cisco VPN, I had the installer does connect more.  The Setup looks right into network preferences. When I click it looks like it is trying but stops without asking for a password.

  Cisco VPN client may need to update or re-installed. If she uses the PPTP Protocol, it will not work. Support for PPTP was ignored, because it is no longer considered as secure.

• IPSec site to site VPN cisco VPN client routing problem and

  Hello

  I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

  The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

  There are on the shelves, there is no material used cisco - routers DLINK.

  Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

  Can someone help me please?

  Thank you

  Peter

  RAYS - not cisco devices / another provider

  Cisco 1841 HSEC HUB:

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key x xx address no.-xauth

  !

  the group x crypto isakmp client configuration

  x key

  pool vpnclientpool

  ACL 190

  include-local-lan

  !

  86400 seconds, duration of life crypto ipsec security association

  Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

  !

  Crypto-map dynamic dynmap 10

  Set transform-set 1cisco

  !

  card crypto ETH0 client authentication list userauthen

  card crypto isakmp authorization list groupauthor ETH0

  client configuration address card crypto ETH0 answer

  ETH0 1 ipsec-isakmp crypto map

  set peer x

  Set transform-set 1cisco

  PFS group2 Set

  match address 180

  card ETH0 10-isakmp ipsec crypto dynamic dynmap

  !

  !

  interface FastEthernet0/1

  Description $ES_WAN$

  card crypto ETH0

  !

  IP local pool vpnclientpool 192.168.200.100 192.168.200.150

  !

  !

  overload of IP nat inside source list LOCAL interface FastEthernet0/1

  !

  IP access-list extended LOCAL

  deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  IP 192.168.7.0 allow 0.0.0.255 any

  !

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  !

  How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

  Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

  DE:

  access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

  access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

  TO:

  access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

  Also change the ACL 190 split tunnel:

  DE:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

  TO:

  access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

  access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

  Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

  Hope that helps.

• using cloud at work and at home.

  I log in the cloud at home using my user id and he pushes me as if I need the product license.

  What to do to log into the cloud at the office and at home?

  The system acts as if I am a new user who want a trial version.

  Hello

  First of all, disconnect, then back into creative cloud, using adobe id to pay for your subscription.

  https://helpx.Adobe.com/creative-cloud/help/sign-in-out-activate-apps.html

  Then, if you launch any product of CC 2015 and the pop up still shows a trial message window, please check this link for the resolution:

  https://helpx.Adobe.com/manage-account-membership/CC-reverts-to-trial.html

• NAT via LAN-to-LAN configuration between router IOS and Cisco VPN 3000

  Hello

  I have the following document on the creation of a virtual LAN2LAN including NAT private network.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00801ae24c.shtml

  It? s easily do this with the hub. Now, I have to set it up on the IOS router, and for this purpose, I can? t find any information. NAT, I have my private network to a single IP address that must be by tunnel as my local network official.

  Anyone have documentation on this szenario? I can? t is not on the OCC.

  Thanks for the support

  Hello.

  Concentrators are very friendly units (IMHO) to VPN with NAT and VPN.

  You build an acl defined traffic over the vpn (110) based on the nat wouldn't

  You create an acl to set what is NAT had (111) and create a NAT statement accordingly

  Here is an example configuration.

  !

  crypto ISAKMP policy 10

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  vpnsrock crypto isakmp key! address x.x.x.x

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  !

  10 VPN ipsec-isakmp crypto map

  defined peer x.x.x.x

  game of transformation-ESP-3DES-SHA

  match address 110

  !

  interface Fa0

  NAT outside IP

  VPN crypto card

  !

  !

  interface fa1

  IP nat inside

  !

  IP nat inside source list 111 interface fa0 overload

  IP route 0.0.0.0 0.0.0.0 y.y.y.y

  access-list 110 permit ip fa0 - ip network-remote control-generic generic-mask

  access-list 111 allow local-network ip network-remote control-generic generic-mask

  !

• Is there a problem with firefox does not, it's happening on all our computers at work and at home. It takes about 10 seconds, then stops responding.

  I read FF posts of the community, and it seems to be a problem with a lot of ppl. It happened for about 3 days now on all our computers at home and work. This cannot just be linked to a computer if this happens for many. I was wondering if there is a general problem with FF, is that what is happening for many users. When I start FF I am lucky to get 10 sec before it does more, ready to give FF film! I use it in safe mode now & use of IE next until I find another solution other than resetting FF. FF should maybe see if there is a problem at their end, & then show us how to fix it.

  To return to regard to extensions, you can view and update the extensions on page modules. Either:

  • CTRL + SHIFT + a
  • Firefox orange (or the Tools menu) button > Add ons

  In the left column, click Extensions. Click the "gear" above the list, and then use the check for updates.

  You can also disable non-essential or unrecognized extensions (or so obviously not good, remove them).

  Typically, a link will appear above at least an extension disabled/removed to restart Firefox. You can complete your work on the tab and click one of the links in the last step.

  Any improvement?

• "back" button does not work and the home page does not display on startup

  My buttons next and previous no longer work. They show just gray and I cannot click on them.
  Also my home page does not appear when I launch firefox.
  I reinstalled firefox 4 and then I went back to firefox 3.6.16 and have the same problem in both versions.
  Don't know what to do anymore
  I just found out that when I opened a second window everything works well in the second window, but it still does not work in the first window.
  The same thing happens when I close both windows. The first window of my home page does not appear and the back button does not work, but the second window is operating normally. Including my home page.

  Try:

  • http://KB.mozillazine.org/Corrupt_localstore.RDF

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the Add-ons is the cause of the problem (switch to the DEFAULT theme: Tools > Modules > appearance/themes).

  • Makes no changes on the start safe mode window.

  See:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox

• LAN-to-LAN tunnel between VPN 3000 and Cisco 1721

  Hello

  I have a current LAN-to-LAN tunnel configuration between VPN 3000 (3.6) and Cisco 1721 (12.2 (11) T).

  When I use the encryption = authentication and Des-56 = ESP\MD5\HMAC-128 for the IPSec Security Association, everything works fine.

  However, I would like to Turn off encryption for some time getting the speed improvements, so I changed

  Encryption = null esp (in 1721) and to "null" in VPN-3000.

  Now the tunnel is setup but I can spend only ICMP traffic. When I pass the traffic UDP\TCP the message below appears the Cisco 1721

  % C1700_EM-1-ERROR: error in packet-rx: pad size error, id 75, hen offset 0

  Has anyone seen this behavior?

  All those put in place an IPSec Tunnel with only the ESP authentication and NO encryption between VPN-3000 and Cisco 1721?

  Thanx------Naman

  Naman,

  Disable you the vpn Accelerator? "no accel crypto engine. Sure that you can't do with a null module vpn.

  Kurtis Durrett

• Cisco ACS 5.4 and VPN 3000

  Hello

  I'm trying to use CIsco ACS 5.4 for RADIUS authentication for VPN by using VPN concentrator 3000 users.

  I added the VPN 3000 on ACS and added GBA on VPN group with a shared secret authentication server. When I do a test on the authentication server using the local account that I created on ACS it happens as no response was received from the server so that I can see the RAIDUS AAuth in green.

  Any help would be much appreciated.

  Concerning

  AR

  Hey,.

  What is the report on GBA?

  "RAIDUS AAuth in green"

  If so, a pcap help between the two.

  Concerning

  Ed

• If I sign up for a year, canI use CS6 on more than 1 pc? (work and home)

  As the title really - just want to know if I join, I'll be able to use the account to use PS at work and at home?

  Thank you

  Fodley123 You can use applications CS6 on upto 2 machines.

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• Using Cisco VPN with desktop remotely

  Hi, I work with many customers that use Cisco VPN for remote access.  Unfortunately the Cisco VPN does not work well with my VPN IBM client so I can't have both running on my computer.  So, I thought that I would like to install the Cisco VPN on an old machine, connect to this computer via desktop to distance and VPN in the network from the customer via the VPN.

  Well, who does not work either.  As soon as I connect to the network via the VPN Remote Desktop client loses the connection.  Can someone tell me if it works as designed (WAD) or if there is a secret of configuration to operate?

  Thanks in advance...

  John,

  When you connect via VPN to the network client on the remote computer, the connection RD proper case?

  I think it's because the VPN connection that you have drawn on the client computer is configured to encrypt all traffic, and that's why the RD connection to your computer of the drops.

  You can do a quick test... on the VPN client computer under statististics (VPN software) verification and check if secure roads is 0.0.0.0 (no split tunneling).

  If Yes... and if having access to the VPN server, which can be changed.

  Federico.