Using Cisco VPN with desktop remotely

Similar Questions

• Can connect with desktop remotely all directions except via internet Windows XP to Windows 7

  I have a new computer with Windows 7 Pro to work I need with desktop remote access so that I can work from home and be with the family.  For years I used remote desktop connection from home using Win XP SP3 to my Win XP Pro SP3 computer at work.  I am able to connect my old WinXP computer work on my new Win 7 computer (locally).  I can connect from home computer Win XP Win XP computer via internet (DSL) to work.  I can connect from Windows 7 computer to work at Windows XP home computer over the internet (DSL).

  So, I have Setup port forwarding or modems DSL correctly, the IP addresses are correct, consistent remote desktop clients. Firewall exceptions are configured correctly.

  What is different.  The new computer with Windows 7 Pro has McAfee Internet Security all others running EAST of Kaspersky.  Win 7 computer is new.  Since I am on various possibilities of connections, changed listening port of 3389 on some computers, including the new Win7 computer (this should not be a problem that I'm able to connect locally).

  Disable the firewall (software Anti-anti-virus/IS) on both computers does not help. In any case, I can go to WinXP Pro to work on Win 7 computer to work locally.

  My thought is that there may some security policies, or maybe a protocol problem which is different with the new Windows 7 computer that does not have a connection outside the local network (via a public network).

  I also tried to set up a VPN connection integrated Microsoft: forwarded port 1723, the GRE protocol allowed to the DSL modem.  Tried all different scenarios between Win XP Home and Win 7 computer at work and cannot configure the VPN connection. I get error 678: the remote computer did not respond.

  I spent hundreds of discussions help/knowledge base and discussion review.  I have seen or followed all the instructions on the various sites of tech Web to configure VPN connections and Remote Desktop connections.

  Does anyone have an idea as to what could be the solution here?

  Hello

  Please post your request in the Microsoft TechNet forum, where experts on this platform can help you with the problem.

  Please see the link that will take you on the TechNet forums below:
   
  https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• Using Cisco VPN Client in Windows 7 Professional 64 bit

  Hi all!
  I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

  Open the XP VM itself, do not use the shortcut that was published in
  the W7 boot menu. You need to install Outlook / your email client
  Inside the virtual machine, as well as on the side of W7. You can point to the same
  PST files if you have local PST files, but you just can't open them in
  at the same time of W7 and XP VM.

  There is no way to bridge using the shortcut of publishing app

  Some people have reported success with the third party IPSec
  replacements as customer universal shrew or the NCP. Your IT Department.
  would like to know if these are supported

  :

  > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
  Barb Bowman www.digitalmediaphile.com

• Different classes using Cisco VPN Client VPN

  Hello

  on a cisco ASA 5510, I defined a vpn group used for remote teleworkers who have access to the entire LAN using Cisco VPN Client 4.8.

  I would give to others of this client, but I need to limit their access to LAN resources, which means that I have to have two types of users:

  Remote LAN access

  access to only certain IP addresses

  Both must use the Cisco VPN client.

  How can I do?

  Thank you

  This link should help.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080641a52.shtml

• Slow initial connection using Cisco VPN Client

  I am currently using Cisco VPN Client v5.0.07.0290.  Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully.  I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">

  Hi Sergio,

  You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.

  Thank you

  Delvallée

• Connection to remote desktop using proxy and gateway desktop remotely?

  I have setup a gateway desktop remotely using Windows Server R2 2012 server. I use Remote Desktop gateway as an intermediary between to offer remote desktop session more than 443 because 3389 is blocked in several places of the customer.

  However, I encountered a problem with a customer that the network seems to use a web proxy.

  Is is possible to set up remote desktop to connect via web proxy? If so, how? If this is not the case, does anyone have any suggestions on how to provide a remote desktop session through 443 on proxy for situations where you don't control the client PC or network? RemoteApps allows access through the web proxy when you use Remote Desktop gateway?

  The error message is below to:

  Your computer cannot connect to the remote computer because the web proxy server requires authentication. To allow traffic not authenticated to a desktop gateway server remotely through your web proxy server, contact your network administrator.

  Thanks for any help!

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet Forum
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information helps.

• Using Cisco VPN Client VPN

  Is it possible to use a private network virtual created with the WRVS4400N router with VPN Client from Cisco Systems (ver 5) software? (Although QuickVPN works very well.)

  Is it possible to use with Account customer VPN mode? Or is it possible to use with IPSec VPN (Tunnel) mode? If so, please provide together how to client-side and the router. Thank you!

  Unfortunately Small Business routers are not compatible with the Cisco VPN Clients. The Cisco VPN Clients have more parameters that are not available in the materials of the series of small businesses, so all we can use is the application of QVPN.

• Professional Windows Vista crashes when you use Cisco VPN Client 5.05.0290

  I have a Dell Latitude E6400 Windows Vista Business (32 bit) operating system. When I go to turn on the VPN client, I get invited to my username / password and once entered, the system just hangs. The only way to answer, it's a re-start. I took action:

  1 disabled UAC in Windows
  2 tried an earlier version of the VPN client
  3. by the representative of Cisco, I put the application runs as an administrator

  If there are any suggestions or similar stories, I would be grateful any offereings.

  It IS the COMODO Firewall with the 5.0.x CISCO VPN client that causes the gel. The last update of COMODO has caused some incompatibility. I tried to install COMODO without the built in Zonealerm, but it is still frozen. The only way to solve it is to uninstall COMODOD. Since then, my CISCO VPN client works again...

• Cannot use Cisco vpn client

  Dear all,

  I have cisco vpn client v5.0.05.

  1 / when I lunch the customer, it connect to the asa, so I can't reach the network behind my ASA

  2 / when connected to the vpn client, I can not use my access to the internet, I configured splitunnel, but does not.

  3 / sometimes, cisco vpn client disable my network ip of the gateway card.

  Please, can someone help me?

  Concerning

  Can you please share the configuration of the SAA. There is no specific configuration that must be done on the vpn client.

• Unable to connect with desktop remotely

  With Windows 7 Pro, try connecting to office having same exact OS W7 pro, both machines are new Dell XPS 8700 s. I get message failed to connect as another 1.2.3 off voltage, i.e., cables etc bad machine. Not true because I can connect to the office with old laptop on XP machine. All other remote employees running W 7 pro can connect to their respective port passed from office machines. I tried every permutation in the desktop settings remotely. I disabled the firewall, checked the services, checked the Office remotely activate, checked the equipment completely but still unable to connect. Someone at - it a suggestions?

  Al

  Hello

  I apologize for the delay in response

  This query is better suited on the TechNet forums. The pros on this forum should be able to help with this query. So, I suggest you to post this query on the TechNet Windows 7 networking Forums by using this link:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking%2Cw7itprosecurity%2Cw7itprohardware&filter=AllTypes&sort=lastpostdesc

  Hope this information was useful. Please get back to us with the results and if you need help or have questions about windows, we will be happy to help you.

• How to use your laptop with ftp remote?

  Dear Sir.

  Does any - one has information on the way to another computer, the files on my computer using laptop tecra M2 (ftp,...)
  Maybe a question too long to respond to?
  Thanks in advance

  Reg weekx

  Hi again

  You are absolutely right. Answer to this question can be long and in my opinion, it is better to look for the solution using the internet. You will find lots of detailed information on this topic.

• Problem Cisco VPN Client with local authentication

  I configured PIX for the Cisco VPN client for remote access. It must be connected and also inside network is accessible. It is without any authentication username. It works well with a vpngroup name and the password for the vpngroup, configured on PIX and also on the Cisco VPN client. (version 4.6)

  When I configure crypto for local authentication, it did not work. configuration is as follows.

  #crypto card: name of the map of local authentication client

  I created a user with private = 15.

  Client VPN must be connected, and then it pops up a window user name and password. After giving these details. The user is not authenticated.

  Are there patterns more to do in / isakmp / ipsec / aaa configurations.

  Thank you

  AAA-server local LOCAL Protocol

  client authentication card crypto remote_vpn LOCAL

  client configuration address card crypto remote_vpn throw

  client configuration address card crypto remote_vpn answer

• Unable to connect to the Cisco VPN using the branch line

  Hello

  We use Cisco VPN Client 5.0.07.0290 to connect to our servers. We have a Sonicwall NSA2400 FW and we have 2 ISPS. We have configured load balancing on firewalls in mode 'Spill-Over '.

  So whenever the 1st line is on full charge, it will automatically moves users on the 2nd line.

  The problem that we face here is the users who get 1st line ISP, they can easily connect to the client VPN Cisco IP, but the users who receive the IP of the 2nd line of the ISP, they are not able to connect to the Cisco VPN Client. It's really annoying because everyone should be able to connect.

  It will be really great if someone can help me as well.

  Thank you

  PS: If Exchange us the line of Sonicwall haapens scenario of Vice versa as mentioned above.

  Hello Sam,.

  Correct me if I help you,.

  In your network that is inside the firewall, you are trying to connect to Cisco VPn client resides outside your network/Public network.

  If the above is the question.

  Please check the routes and roads of sonicwall priority.

  example:

  Isps1: the value of the metric as 1 for traffic destined for cisco VPn IP of the gateway and specify to leave traffic isps1 interface

  ISP2: set the metric 1 once again for the traffic to cisco VPn IP of the gateway and specify to leave traffic ISP2 interface

  interface metric 1 source destination

  Kindly, please note the useful messages and.

  Thank you

  Srikanth

• a PC can not the desktop remotely to a server by using the service account

  The scenario, I have:

  A Windows 7 Enterprise SP1 64 bit pc, lets call it PC1.

  A Windows Server 2008 R2 Enterprise SP1, lets call him Server1.

  A service account, lets call him Service1.

  -PC1 on ad domain network, can ping Server1 by IP and vice versa. PC1 on the same subnet as the other PC.

  -Server1 on a working group, has same DNS as PC1

  -Service1 is used for all the desktop remotely to Server1.

  The problem:

  All the PC's on the field are able to Server1 using Service1 remote desktop, but unable to PC1. (This displays Server1 accepts the remote desktop connection, and credential Service1 works very well)

  Tested PC1 can desktop remotely for all other servers on the network. (cela poster services the PC1 Remote Desktop works fine)

  Error:

  This computer cannot connect to the remote computer.

  Try to connect again. If the problem persists, contact your network administrator or the owner of the remote computer.

  Any idea?

  Server are better to ask questions on the Technet site.

  http://social.technet.Microsoft.com/forums/en-us/categories/

• Lost the VPN tunnel between 2 site when internal client using client vpn

  We currently have VPN tunnel connected to the remote desktop using router VPN Hotbrick 2.

  When 1 of the internal computer try to connect to another server VPN customer using Cisco VPN Client v4.8, she will appear in drop/disable/loss of the tunnel between us VPN and remote offices. The tunnel is still established but no traffice between site 2. (cannot all ping)

  What are the causes of the problem? Hotbrik problem? Customer Cisco VPN setting or something else?

  I don't know what causes the problem. Help, please. Thanks in advance.

  Hello

  The problem is that your NAT device will not translating properly, and when the 2nd customer triggers (ISAKMP packets-UDP 500) connections port isn't transalated, so for the SAA is as the first user tries to connect again, then it rejects the initial connection.

  The trick is, as you have discovered, use global UDP.

  The problem is that UDP 10000 is not a standard, so you need to check if multiple users can be connected at the same time behind the same NAT device.

  If this is not the case, use the NAT transparency standard industry (UDP 4500). This should be configured only on the SAA.

  Please rate if this helped.

  Kind regards

  Daniel