Cisco vpn client 5.0.07 no internet access

I am trying to configure access remote vpn for the ASA 5505 in my office.

The config is configured on my ASA, and I have cisco vpn client 5.0.07 installed on my laptop (64 bit) to Windows 7.  I can start the vpn, put in my references and it seems that everything goes through, but once I'm connected, I lose access to the internet, and I cannot ping anything (4.2.2.2, 192.168.1.1 (gateway), etc...)

I keep seeing something uncheck the "use default gateway on remote network", but this option is available in the TCP/IP properties.  Any suggestions?

Eric,

This should be the last change. Looks like you don't have inside the network split tunnel.

Here is the entry you need to do

TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0

disconnect and reconnect. It should work like a charm.

Thank you

Bad Boy

Tags: Cisco Security

Similar Questions

  • Cisco vpn client to connect but can not access to the internal network

    Hi all

    I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

    Any help would be much appreciated.

    Hi Samir,

    I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

    (The link above includes split tunneling, but this is just an option.

    Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

    Let me know if this can help,

    See you soon,.

    Christian V

  • What are the ports used by the Cisco VPN Client?

    Hello

    I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

    I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

    What are the ports used by the Cisco VPN Client?

    Thank you

    You need to open:

    UDP 500

    ESP protocol

    You must also open the UDP 4500 port (if using NAT - T).

    In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

    1. If using IPSec over TCP 10000, then open TCP 10000.

    2. If using IPSec over UDP 10000, open UDP 1000.

  • Cisco VPN client with internet

    Hello

    I have a big problem, we have implemented Cisco VPN client to connect to outside to our internal servers. My problem is that all users access to the internet while using the Cisco VPN client. We use the split tunneling, but still all VPN clients access the internet. An advisor to prevent access to the internet through VPN client.

    Thank you

    You said earlier that you allow split tunnel. Are you still doing that?

    We would need to see all of the VPN configuration - including access lists or objects referenced - to provide comprehensive advice.

  • Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

    Hello

    I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

    I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

    Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

    Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
    Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
    Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
    Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

    The router configuration

    IKE policy

    VPN strategy

    Client configuration

    Hôte : < router="" ip=""> >

    Authentication group name: remote.com

    Password authentication of the Group: mysecretpassword

    Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

    Username: myusername

    Password: mypassword

    Please contact Cisco.

    Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

    You can use the PPTP on the RV180 server to connect a PPTP Client.

    In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

  • Cisco VPN Client and Windows XP VPN Client IPSec to ASA

    I configured ASA for IPSec VPN via Cisco VPN Client and XP VPN client communications. I can connect successfully with Cisco VPN Client, but I get an error when connecting with the XP client. Debugging said "misconfigured groups and transport/tunneling mode" I know, they use different methods of transport and tunneling, and I think that I have configured both. Take a look at the config.

    PS a funny thing - when I connect with client VPN in Windows Server 2003, I have no error. The only difference is that client XP is behind an ADSL router and client server is directly connected to the Internet on one of its public IP of interfaces. NAT in the case of XP can cause problems?

    Config is:

    !

    interface GigabitEthernet0/2.30

    Description remote access

    VLAN 30

    nameif remote access

    security-level 0

    IP 85.*. *. 1 255.255.255.0

    !

    access-list 110 scope ip allow a whole

    NAT list extended access permit tcp any host 10.254.17.10 eq ssh

    NAT list extended access permit tcp any host 10.254.17.26 eq ssh

    access-list extended ip allowed any one sheep

    access list nat-ganja extended permit tcp any host 10.254.17.18 eq ssh

    sheep-vpn access-list extended permits all ip 192.168.121.0 255.255.255.0

    tunnel of splitting allowed access list standard 192.168.121.0 255.255.255.0

    flow-export destination inside-Bct 192.168.1.27 9996

    IP local pool raccess 192.168.121.60 - 192.168.121.120 mask 255.255.255.0

    ARP timeout 14400

    global (outside-Baku) 1 interface

    global (outside-Ganja) interface 2

    NAT (inside-Bct) 0 access-list sheep-vpn

    NAT (inside-Bct) 1 access list nat

    NAT (inside-Bct) 2-nat-ganja access list

    Access-group rdp on interface outside-Ganja

    !

    Access remote 0.0.0.0 0.0.0.0 85.*. *. 1 2

    Route outside Baku 10.254.17.24 255.255.255.248 10.254.17.10 1

    Route outside Baku 192.1.1.0 255.255.255.0 10.254.17.10 1

    Outside-Baku route 192.168.39.0 255.255.255.0 10.254.17.10 1

    Route outside-Ganja 192.168.45.0 255.255.255.0 10.254.17.18 1

    Route outside-Ganja 192.168.69.0 255.255.255.0 10.254.17.18 1

    Route outside-Ganja 192.168.184.0 255.255.255.0 10.254.17.18 1

    Route outside Baku 192.168.208.16 255.255.255.240 10.254.17.10 1

    Route outside-Ganja 192.168.208.112 255.255.255.240 10.254.17.18 1

    dynamic-access-policy-registration DfltAccessPolicy

    Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

    Crypto ipsec transform-set newset aes - esp esp-md5-hmac

    Crypto ipsec transform-set esp-3des esp-md5-hmac vpnclienttrans

    Crypto ipsec transform-set vpnclienttrans transport mode

    Crypto ipsec transform-set esp-3des esp-md5-hmac raccess

    life crypto ipsec security association seconds 214748364

    Crypto ipsec kilobytes of life security-association 214748364

    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

    vpnclientmap 30 card crypto ipsec-isakmp dynamic dyn1

    card crypto interface for remote access vpnclientmap

    crypto isakmp identity address

    ISAKMP crypto enable vpntest

    ISAKMP crypto enable outside-Baku

    ISAKMP crypto enable outside-Ganja

    crypto ISAKMP enable remote access

    ISAKMP crypto enable Interior-Bct

    crypto ISAKMP policy 30

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    No encryption isakmp nat-traversal

    No vpn-addr-assign aaa

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.192 outside Baku

    SSH 10.254.17.26 255.255.255.255 outside Baku

    SSH 10.254.17.18 255.255.255.255 outside Baku

    SSH 10.254.17.10 255.255.255.255 outside Baku

    SSH 10.254.17.26 255.255.255.255 outside-Ganja

    SSH 10.254.17.18 255.255.255.255 outside-Ganja

    SSH 10.254.17.10 255.255.255.255 outside-Ganja

    SSH 192.168.1.0 255.255.255.192 Interior-Bct

    internal vpn group policy

    attributes of vpn group policy

    value of DNS-server 192.168.1.3

    Protocol-tunnel-VPN IPSec l2tp ipsec

    Split-tunnel-policy tunnelspecified

    Split-tunnel-network-list value split tunnel

    BCT.AZ value by default-field

    attributes global-tunnel-group DefaultRAGroup

    raccess address pool

    Group-RADIUS authentication server

    Group Policy - by default-vpn

    IPSec-attributes tunnel-group DefaultRAGroup

    pre-shared-key *.

    Hello

    For the Cisco VPN client, you would need a tunnel-group name configured on the ASA with a pre-shared key.

    Please see configuration below:

    http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

    or

    http://tinyurl.com/5t67hd

    Please see the section of tunnel-group config of the SAA.

    There is a tunnel-group called "rtptacvpn" and a pre-shared key associated with it. This group name is used by the VPN Client Group name.

    So, you would need a specific tunnel-group name configured with a pre-shared key and use it on the Cisco VPN Client.

    Secondly, because you are behind a router ADSL, I'm sure that's configured for NAT. can you please activate NAT - T on your ASA.

    "crypto isakmp nat-traversal.

    Thirdly, change the transformation of the value

    raccess 1 set transform-set vpnclienttrans crypto dyn1 dynamic-map

    Let me know the result.

    Thank you

    Gilbert

  • Cisco VPN Client

    Hello

    I would like to know why when it failed to connect to the private network through the Cisco VPN client and trying to establish an Internet connection, the connection Internet.

    Thanks in advance,

    SK

    Which would be configured on the vpn, firewall/router endpoint etc..

  • Cisco VPN client, PIX, and proxy

    Hi.I have problem in my company. We have users that go through a proxy server located in the DMZ of a PIX to the internet (allowed through the ACL of the DMZ on the outside, etc.). Which works very well.

    The problem arises when they use a Cisco VPN client to connect to another company, and they can no longer access the Internet, but may work via VPN to a remote site (client has been authorized by the Cisco PIX). Everything returns to normal when they no longer use the VPN client.

    Any ideas why this would happen?

    Without the proxy, browsing the internet via the vpn connection, or split tunnel is configured and you are leaving locally. If split tunnel is configured, the ip address of proxy server can overlap with the remote protected network.

    Fortunately, it is easy for you to know how the vpn is configured, just check the route details of vpn client statistics tab.

    Verify that the routing table local pc will also help you to solve this problem.

  • Cannot use Cisco vpn client

    Dear all,

    I have cisco vpn client v5.0.05.

    1 / when I lunch the customer, it connect to the asa, so I can't reach the network behind my ASA

    2 / when connected to the vpn client, I can not use my access to the internet, I configured splitunnel, but does not.

    3 / sometimes, cisco vpn client disable my network ip of the gateway card.

    Please, can someone help me?

    Concerning

    Can you please share the configuration of the SAA. There is no specific configuration that must be done on the vpn client.

  • Another problem with the configuration of Cisco VPN Client access VPN Site2site

    We have a Cisco ASA 5505 at our CORP. branch I configured the VPN Site2Site to our COLO with a Juniper SRX220h, to another site works well, but when users access the home Cisco VPN client, they cannot ping or SSH through the Site2Site.  JTACS contacted and they said it is not on their end, so I tried to contact Cisco TAC, no support.  So here I am today, after for the 3 days (including Friday of last week) of searching the Internet for more than 6 hours per day and try different examples of other users. NO LUCK. The VPN client shows the route secure 10.1.0.0

    Sorry to post this, but I'm frustrated and boss breathing down my neck to complete it.

    CORP netowrk 192.168.1.0

    IP VPN 192.168.12.0 pool

    Colo 10.1.0.0 internal ip address

    Also, here's an example of my config ASA

    : Saved

    :

    ASA Version 8.2 (1)

    !

    hostname lwchsasa

    names of

    name 10.1.0.1 colo

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.1.1 255.255.255.0

    !

    interface Vlan2

    backup interface Vlan12

    nameif outside_pri

    security-level 0

    IP 64.20.30.170 255.255.255.248

    !

    interface Vlan12

    nameif backup

    security-level 0

    IP 173.165.159.241 255.255.255.248

    !

    interface Ethernet0/0

    switchport access vlan 2

    !

    interface Ethernet0/1

    switchport access vlan 12

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    passive FTP mode

    permit same-security-traffic inter-interface

    permit same-security-traffic intra-interface

    object-group network NY

    object-network 192.168.100.0 255.255.255.0

    BSRO-3387 tcp service object-group

    port-object eq 3387

    BSRO-3388 tcp service object-group

    port-object eq 3388

    BSRO-3389 tcp service object-group

    EQ port 3389 object

    object-group service tcp OpenAtrium

    port-object eq 8100

    object-group service Proxy tcp

    port-object eq 982

    VOIP10K - 20K udp service object-group

    10000 20000 object-port Beach

    the clientvpn object-group network

    object-network 192.168.12.0 255.255.255.0

    APEX-SSL tcp service object-group

    Description of Apex Dashboard Service

    port-object eq 8586

    object-group network CHS-Colo

    object-network 10.1.0.0 255.255.255.0

    the DM_INLINE_NETWORK_1 object-group network

    object-network 192.168.1.0 255.255.255.0

    host of the object-Network 64.20.30.170

    object-group service DM_INLINE_SERVICE_1

    the purpose of the ip service

    ICMP service object

    service-object icmp traceroute

    the purpose of the service tcp - udp eq www

    the tcp eq ftp service object

    the purpose of the tcp eq ftp service - data

    the eq sqlnet tcp service object

    EQ-ssh tcp service object

    the purpose of the service udp eq www

    the eq tftp udp service object

    object-group service DM_INLINE_SERVICE_2

    the purpose of the ip service

    ICMP service object

    EQ-ssh tcp service object

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 clientvpn object-group

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

    inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    inside_nat0_outbound list of allowed ip extended access any 192.168.12.0 255.255.255.0

    outside_pri_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group NY

    outside_pri_access_in list extended access permit tcp any interface outside_pri eq www

    outside_pri_access_in list extended access permit tcp any outside_pri eq https interface

    outside_pri_access_in list extended access permit tcp any interface outside_pri eq 8100

    outside_pri_access_in list extended access permit tcp any outside_pri eq idle ssh interface

    outside_pri_access_in list extended access permit icmp any any echo response

    outside_pri_access_in list extended access permit icmp any any source-quench

    outside_pri_access_in list extended access allow all unreachable icmp

    outside_pri_access_in list extended access permit icmp any one time exceed

    outside_pri_access_in list extended access permit tcp any 64.20.30.168 255.255.255.248 eq 8586

    levelwingVPN_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0

    levelwingVPN_splitTunnelAcl list standard access allowed 10.1.0.0 255.255.255.0

    outside_pri_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    backup_nat0_outbound list extended access allowed object-group DM_INLINE_NETWORK_1 192.168.12.0 ip 255.255.255.0

    outside_pri_cryptomap_1 list extended access allow DM_INLINE_SERVICE_2 of object-group 192.168.1.0 255.255.255.0 10.1.0.0 255.255.255.0

    outside_19_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

    inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 object-group CHS-Colo

    VPN-Corp-Colo extended access list permits object-group DM_INLINE_SERVICE_1 192.168.12.0 255.255.255.0 10.1.0.0 255.255.255.0

    Note to OUTSIDE-NAT0 NAT0 customer VPN remote site access-list

    OUTSIDE-NAT0 192.168.12.0 ip extended access list allow 255.255.255.0 10.1.0.0 255.255.255.0

    L2LVPN to access extended list ip 192.168.12.0 allow 255.255.255.0 10.1.0.0 255.255.255.0

    pager lines 24

    Enable logging

    debug logging in buffered memory

    exploitation forest asdm warnings

    record of the rate-limit unlimited level 4

    destination of exports flow inside 192.168.1.1 2055

    timeout-rate flow-export model 1

    Within 1500 MTU

    outside_pri MTU 1500

    backup of MTU 1500

    local pool LVCHSVPN 192.168.12.100 - 192.168.12.254 255.255.255.0 IP mask

    no failover

    ICMP unreachable rate-limit 100 burst-size 5

    ICMP allow any inside

    ICMP allow any outside_pri

    don't allow no asdm history

    ARP timeout 14400

    NAT-control

    interface of global (outside_pri) 1

    Global 1 interface (backup)

    NAT (inside) 0-list of access inside_nat0_outbound

    NAT (inside) 0 inside_nat0_outbound_1 list of outdoor access

    NAT (inside) 1 0.0.0.0 0.0.0.0

    NAT (outside_pri) 0-list of access OUTSIDE-NAT0

    backup_nat0_outbound (backup) NAT 0 access list

    static TCP (inside outside_pri) interface https 192.168.1.45 https netmask 255.255.255.255 dns

    static TCP (inside outside_pri) interface 192.168.1.45 www www netmask 255.255.255.255 dns

    static TCP (inside outside_pri) interface 8586 192.168.1.45 8586 netmask 255.255.255.255 dns

    static (inside, inside) tcp interface 8100 192.168.1.45 8100 netmask 255.255.255.255 dns

    Access-group outside_pri_access_in in the outside_pri interface

    Route 0.0.0.0 outside_pri 0.0.0.0 64.20.30.169 1 track 1

    Backup route 0.0.0.0 0.0.0.0 173.165.159.246 254

    Timeout xlate 03:00

    Conn Timeout 0:00:00 half-closed 0:30:00 udp icmp from 01:00 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 01:00 uauth uauth absolute inactivity from 01:00

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    AAA authentication enable LOCAL console

    AAA authentication http LOCAL console

    the ssh LOCAL console AAA authentication

    http server enable 981

    http 192.168.1.0 255.255.255.0 inside

    http 0.0.0.0 0.0.0.0 outside_pri

    http 0.0.0.0 0.0.0.0 backup

    SNMP server group Authentication_Only v3 auth

    SNMP-server host inside 192.168.1.47 survey community lwmedia version 2 c

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown cold start

    Sysopt connection tcpmss 1200

    monitor SLA 123

    type echo protocol ipIcmpEcho 216.59.44.220 interface outside_pri

    Annex ALS life monitor 123 to always start-time now

    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set esp-3des-sha1 esp-3des esp-sha-hmac

    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

    life crypto ipsec security association seconds 28800

    Crypto ipsec kilobytes of life - safety 4608000 association

    Crypto ipsec df - bit clear-df outside_pri

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    card crypto outside_pri_map 1 match address outside_pri_1_cryptomap

    card crypto outside_pri_map 1 set pfs

    peer set card crypto outside_pri_map 1 50.75.217.246

    card crypto outside_pri_map 1 set of transformation-ESP-AES-256-MD5

    card crypto outside_pri_map 2 match address outside_pri_cryptomap

    peer set card crypto outside_pri_map 2 216.59.44.220

    card crypto outside_pri_map 2 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    86400 seconds, duration of life card crypto outside_pri_map 2 set security-association

    card crypto outside_pri_map 3 match address outside_pri_cryptomap_1

    peer set card crypto outside_pri_map 3 216.59.44.220

    outside_pri_map crypto map 3 the value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    outside_pri_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    card crypto outside_pri_map interface outside_pri

    crypto isakmp identity address

    ISAKMP crypto enable outside_pri

    crypto ISAKMP policy 5

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 10

    preshared authentication

    the Encryption

    sha hash

    Group 2

    life 86400

    crypto ISAKMP policy 30

    preshared authentication

    aes-256 encryption

    md5 hash

    Group 2

    life 86400

    crypto ISAKMP policy 50

    preshared authentication

    aes encryption

    md5 hash

    Group 2

    life 86400

    !

    track 1 rtr 123 accessibility

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.0 inside

    SSH timeout 5

    Console timeout 0

    management-access inside

    dhcpd auto_config outside_pri

    !

    dhcpd address 192.168.1.51 - 192.168.1.245 inside

    dhcpd dns 8.8.8.8 8.8.4.4 interface inside

    rental contract interface 86400 dhcpd inside

    dhcpd field LM inside interface

    dhcpd allow inside

    !

    a basic threat threat detection

    statistical threat detection port

    Statistical threat detection Protocol

    Statistics-list of access threat detection

    a statistical threat detection host number rate 2

    no statistical threat detection tcp-interception

    WebVPN

    port 980

    allow inside

    Select outside_pri

    enable SVC

    attributes of Group Policy DfltGrpPolicy

    VPN-idle-timeout no

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    internal GroupPolicy2 group strategy

    attributes of Group Policy GroupPolicy2

    Protocol-tunnel-VPN IPSec svc

    internal levelwingVPN group policy

    attributes of the strategy of group levelwingVPN

    Protocol-tunnel-VPN IPSec svc webvpn

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list levelwingVPN_splitTunnelAcl

    username password encrypted Z74.JN3DGMNlP0H2 privilege 0 aard

    aard attribute username

    VPN-group-policy levelwingVPN

    type of remote access service

    rcossentino 4UpCXRA6T2ysRRdE encrypted password username

    username rcossentino attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    bcherok evwBWqKKwrlABAUp encrypted password username

    username bcherok attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    rscott nIOnWcZCACUWjgaP encrypted password privilege 0 username

    rscott username attributes

    VPN-group-policy levelwingVPN

    sryan 47u/nJvfm6kprQDs password encrypted username

    sryan username attributes

    VPN-group-policy levelwingVPN

    type of nas-prompt service

    username, password cbruch a8R5NwL5Cz/LFzRm encrypted privilege 0

    username cbruch attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    apellegrino yy2aM21dV/11h7fR password encrypted username

    username apellegrino attributes

    VPN-group-policy levelwingVPN

    type of remote access service

    username rtuttle encrypted password privilege 0 79ROD7fRw5C4.l5

    username rtuttle attributes

    VPN-group-policy levelwingVPN

    username privilege 15 encrypted password vJFHerTwBy8dRiyW levelwingadmin

    username password nbrothers Amjc/rm5PYhoysB5 encrypted privilege 0

    username nbrothers attributes

    VPN-group-policy levelwingVPN

    clong z.yb0Oc09oP3/mXV encrypted password username

    clong attributes username

    VPN-group-policy levelwingVPN

    type of remote access service

    username, password finance 9TxE6jWN/Di4eZ8w encrypted privilege 0

    username attributes finance

    VPN-group-policy levelwingVPN

    Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn

    type of remote access service

    IPSec-attributes tunnel-group DefaultL2LGroup

    Disable ISAKMP keepalive

    tunnel-group 50.75.217.246 type ipsec-l2l

    IPSec-attributes tunnel-group 50.75.217.246

    pre-shared-key *.

    Disable ISAKMP keepalive

    type tunnel-group levelwingVPN remote access

    tunnel-group levelwingVPN General-attributes

    address LVCHSVPN pool

    Group Policy - by default-levelwingVPN

    levelwingVPN group of tunnel ipsec-attributes

    pre-shared-key *.

    tunnel-group 216.59.44.221 type ipsec-l2l

    IPSec-attributes tunnel-group 216.59.44.221

    pre-shared-key *.

    tunnel-group 216.59.44.220 type ipsec-l2l

    IPSec-attributes tunnel-group 216.59.44.220

    pre-shared-key *.

    Disable ISAKMP keepalive

    !

    !

    !

    Policy-map global_policy

    !

    context of prompt hostname

    Cryptochecksum:ed7f4451c98151b759d24a7d4387935b

    : end

    Hello

    It seems to me that you've covered most of the things.

    You however not "said" Configuring VPN L2L that traffic between the pool of VPN and network camp should be in tunnel

    outside_pri_cryptomap to access extended list ip 192.168.12.0 allow 255.255.255.0 object-group CHS-Colo

    Although naturally the remote end must also the corresponding configurations for users of VPN clients be able to pass traffic to the site of the camp.

    -Jouni

  • Cannot access remote resources - Cisco VPN Client

    I'm having a problem with my Cisco VPN Client. I am new to VPN configuration, so this is probably something easy I'm missing. I have a my internet gateway for my LAN 2611XM router and my VPN server. I do all my tests of a society with a high card laptop mobile broadband. VPN connects, but anytime I ping anything in the network Cabinet, he returned with the public IP address of the external interface. I have NAT overload configured so any network can access the internet, inside which it looks like may be causing my problem. I don't know how to fix it. My config running is attatched. No one knows what might happen.

    Oh, almost forgot to add. When I remove the nat overload on my interface fa0/1, the vpn will connect to any resource on the inside.

    Your nat configuration seems to be the origin of the problem. If you are using an ACL to match the source for NAT, then it will be necessary to add the line 1A refuse for the local ip pool for your vpn clients to one only. try that to see how it goes.

    Sent by Cisco Support technique iPhone App

  • Cisco VPN client put in place

    Hi guru of cisco

    Help me please to configure VPN access on ASA 5505 for Cisco VPN Client. I want to let the customers gateway, but access remote 192.168.17.0/24 and 192.168.10.0/24 (connected through site-to-site) networks.

    Will be much appreciated for your help.

    My config:

    Output from the command: 'display conf '.

    !
    ASA Version 8.2 (2)
    !
    name of host host1
    domain domain name
    activate the encrypted password password
    encrypted passwd password
    names of
    !
    interface Vlan1
    Description INTERNET
    0000.0000.0001 Mac address
    nameif WAN
    security-level 0
    IP address a.a.a.a 255.255.255.248 watch a1.a1.a1.a1
    OSPF cost 10
    !
    interface Vlan2
    OLD-PRIVATE description
    0000.0000.0102 Mac address
    nameif OLD-private
    security-level 100
    IP 192.168.17.2 255.255.255.0 watch 192.168.17.3
    OSPF cost 10
    !
    interface Vlan6
    Description MANAGEMENT
    0000.0000.0106 Mac address
    nameif management
    security-level 100
    IP 192.168.1.2 255.255.255.0 ensures 192.168.1.3
    OSPF cost 10
    !
    interface Vlan100
    Failover LAN Interface Description
    !
    interface Ethernet0/0
    !
    interface Ethernet0/1
    Shutdown
    !
    interface Ethernet0/2
    Shutdown
    !
    interface Ethernet0/3
    Shutdown
    !
    interface Ethernet0/4
    Shutdown
    !
    interface Ethernet0/5
    switchport access vlan 100
    !
    interface Ethernet0/6
    switchport trunk allowed vlan 2.6
    switchport mode trunk
    !
    interface Ethernet0/7
    Shutdown
    !
    boot system Disk0: / asa822 - k8.bin
    passive FTP mode
    DNS domain-lookup WAN
    DNS server-group DefaultDNS
    Server name dns.dns.dns.dns
    domain domain name
    permit same-security-traffic intra-interface
    object-group Protocol TCPUDP
    object-protocol udp
    object-tcp protocol
    object-group service RDP - tcp
    RDP description
    EQ port 3389 object
    object-group Protocol DM_INLINE_PROTOCOL_1
    ip protocol object
    icmp protocol object
    object-protocol udp
    object-tcp protocol
    Access extensive list ip 192.168.17.0 LAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
    Standard access list LAN_IP allow 192.168.17.0 255.255.255.0
    WAN_access_in list of allowed ip extended access all any debug log
    WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 192.168.10.0 255.255.255.0 inactive debug log
    WAN_access_in list extended access permit tcp any object-group RDP any RDP log debugging object-group
    WAN_access_in list extended access allowed icmp a.a.a.a 255.255.255.248 a.a.a.a 255.255.255.248 debug log
    MANAGEMENT_access_in list of allowed ip extended access all any debug log
    access-list extended OLD-PRIVATE_access_in any allowed ip no matter what debug log
    access-list OLD-PRIVATE_access_in allowed extended object-group DM_INLINE_PROTOCOL_1 interface OLD-private 192.168.10.0 255.255.255.0 inactive debug log
    access-list OLD-PRIVATE_access_in allowed extended object-group TCPUDP interface OLD-private no matter what inactive debug log
    access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.10.254 interface private OLD newspaper inactive debugging
    access-list OLD-PRIVATE_access_in allowed extended icmp host 192.168.17.155 interface private OLD newspaper debugging
    access-list 101 extended allow host tcp 192.168.10.7 any eq 3389 debug log
    Access extensive list ip 192.168.17.0 WAN_1_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
    WAN_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
    WAN_cryptomap_2 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.0
    Capin list extended access permit ip host 192.18.17.155 192.168.10.7
    Capin list extended access permit ip host 192.168.10.7 192.168.17.155
    LAN_access_in list of allowed ip extended access all any debug log
    Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0
    WAN_nat0_outbound list of allowed ip extended access all 192.168.17.240 255.255.255.252
    WAN_nat0_outbound to access extended list ip 192.168.2.0 allow 255.255.255.0 192.168.2.0 255.255.255.248
    Access extensive list ip 192.168.17.0 WAN_2_cryptomap allow 255.255.255.0 192.168.10.0 255.255.255.0
    permit inside_nat0_outbound to access extended list ip 192.168.10.0 255.255.255.0 192.168.17.0 255.255.255.0
    LAN_IP_inbound list standard access allowed 192.168.10.0 255.255.255.0
    Standard access list IPSec_VPN_splitTunnelAcl allow a
    access extensive list ip 192.168.17.0 vpnusers_splitTunnelAcl allow 255.255.255.0 any
    sheep - in extended Access-list allow IP 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0
    vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
    pager lines 24
    Enable logging
    logging trap information
    asdm of logging of information
    Debugging trace record
    MTU 1500 WAN
    MTU 1500 OLD-private
    MTU 1500 management
    mask 192.168.1.150 - 192.168.1.199 255.255.255.0 IP local pool VPN_Admin_IP
    IP local pool vpnclient 192.168.2.1 - 192.168.2.5 mask 255.255.255.0
    failover
    primary failover lan unit
    failover lan interface failover Vlan100
    15 75 holdtime interface failover pollTime
    key changeover *.
    failover interface ip failover 192.168.100.1 255.255.255.0 ensures 192.168.100.2
    ICMP unreachable rate-limit 1 burst-size 1
    ICMP permitted host b.b.b.b WAN
    ICMP allow 192.168.10.0 255.255.255.0 WAN
    ICMP permitted host c.c.c.c WAN
    ICMP allow 192.168.17.0 255.255.255.0 WAN
    ICMP deny any WAN
    ICMP permitted host OLD-private b.b.b.b
    ICMP allow 192.168.10.0 255.255.255.0 OLD-private
    ICMP allow 192.168.17.0 255.255.255.0 OLD-private
    ICMP permitted host c.c.c.c OLD-private
    ICMP permitted host b.b.b.b management
    ICMP permitted host 192.168.10.0 management
    ICMP permitted host 192.168.17.138 management
    ICMP permit 192.168.1.0 255.255.255.0 management
    ICMP permitted host 192.168.1.26 management
    ASDM image disk0: / asdm - 631.bin
    don't allow no asdm history
    ARP timeout 14400
    Global (WAN) 1 interface
    Global (OLD-private) 1 interface
    Global interface (management) 1
    NAT (OLD-private) 0-list of access WAN_nat0_outbound
    NAT (OLD-private) 1 0.0.0.0 0.0.0.0
    WAN_access_in access to the WAN interface group
    Access-group interface private-OLD OLD-PRIVATE_access_in
    Access-group MANAGEMENT_access_in in the management interface
    Route WAN 0.0.0.0 0.0.0.0 a.a.a.185 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    the ssh LOCAL console AAA authentication
    local AAA authentication attempts 10 max in case of failure
    Enable http server
    http 192.168.1.0 255.255.255.0 WAN
    http 0.0.0.0 0.0.0.0 WAN
    http a.a.a.a 255.255.255.255 WAN
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Service resetoutside
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
    Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    card crypto WAN_map 1 corresponds to the address WAN_1_cryptomap
    card crypto WAN_map 1 set peer b.b.b.b
    WAN_map 1 transform-set ESP-DES-SHA crypto card game
    card crypto WAN_map WAN interface
    ISAKMP crypto enable WAN
    crypto ISAKMP policy 10
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 86400
    crypto ISAKMP policy 30
    preshared authentication
    the Encryption
    sha hash
    Group 1
    life 86400
    Telnet timeout 5
    SSH b.b.b.b 255.255.255.255 WAN
    SSH timeout 30
    SSH version 2
    Console timeout 0
    dhcpd auto_config OLD-private
    !

    a basic threat threat detection
    host of statistical threat detection
    Statistics-list of access threat detection
    a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
    NTP server 129.6.15.28 source WAN prefer
    WebVPN
    attributes of Group Policy DfltGrpPolicy
    Protocol-tunnel-VPN IPSec svc webvpn
    internal admin group strategy
    group admin policy attributes
    DNS.DNS.DNS.DNS value of DNS server
    Protocol-tunnel-VPN IPSec
    internal vpn_ipsec group policy
    attributes of the strategy of group vpn_ipsec
    value 192.168.17.80 DNS server dns.dns.dns.dns
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list vpn_ipsec_splitTunnelAcl
    the address value vpnclient pools
    username admin password encrypted password privilege 15
    n1ck encrypted password privilege 15 password username
    type tunnel-group admin remote access
    tunnel-group admin general attributes
    address pool IPSec_VPN_pool
    vpnclient address pool
    LOCAL authority-server-group
    strategy-group-by default admin
    tunnel-group admin ipsec-attributes
    pre-shared-key *.
    tunnel-group b.b.b.b type ipsec-l2l
    tunnel-group b.b.b.b General-attributes
    strategy-group-by default admin
    b.b.b.b tunnel ipsec-attributes group
    pre-shared-key *.
    NOCHECK Peer-id-validate
    type tunnel-group vpn_ipsec remote access
    tunnel-group vpn_ipsec General-attributes
    vpnclient address pool
    Group Policy - by default-vpn_ipsec
    vpn_ipsec group of tunnel ipsec-attributes
    pre-shared-key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    maximum message length automatic of customer
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    Review the ip options
    inspect the icmp

    Thanks a lot for the confirmation. There is some lack of configurations and also some configuration errors.

    They are here:

    (1) Split tunnel-access list is incorrect:

    vpn_ipsec_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0

    It should be allowed in your internal network. Please, add and remove the following:

    standard access list vpn_ipsec_splitTunnelAcl allow 192.168.17.0 255.255.255.0

    No vpn_ipsec_splitTunnelAcl of the standard access list only allowed 192.168.2.0 255.255.255.0

    (2) NAT 0-list of access should also include the traffic between the local subnet to the Pool of IP VPN:

    Access extensive list ip 192.168.17.0 WAN_nat0_outbound allow 255.255.255.0 192.168.2.0 255.255.255.0

    (3) dynamic-map has not been created and assigned to crypto card:

    Crypto-map dynamic dynmap 10 game of transformation-ESP-3DES-SHA

    card crypto ipsec WAN_map 65000-isakmp dynamic dynmap

    (4) Finally, you have not enabled protocol IPSec in your group strategy:

    attributes of the strategy of group vpn_ipsec

    Protocol-tunnel-VPN IPSec

    Hope that helps.

    If it still does not after the changes described above, please kindly share the latest config and also the output of the following debugs when you try to connect:

    debugging cry isa

    debugging ipsec cry

  • Cisco VPN Client causes a blue screen crash on Windows XP Pro (Satellite M30)

    Hello

    I have a Satellite Pro M30 running Windows XP Professional.

    After you start a vpn Tunnel via a customer of Cisco VPN (Version 4.6 and 4.7), the system crashes with a blue screen.

    I see that the key exchange is successful, but immediately after the vpn connection is established Windows XP crashes with a blue screen.

    Someone has any idea how to solve this problem?

    Perhaps by the updated device driver? And if so, which driver should be updated?

    Kind regards

    Thorsten

    Hello

    Well, it seems that the Cisco client is a problem.
    I m unaware of this product because it of not designed by Toshiba.
    I think that the drivers are not compatible with the Windows operating system.
    However, I found this site troubleshooting cisco vpn client:
    Please check this:
    http://www.CITES.uiuc.edu/wireless/trouble-index.html

  • Receive message "Validation of C:\WINDOWS\System32\VSINIT.dll failure" error message when trying to run Cisco VPN Client.

    windows\system32\vsinit.dll

    I try to run CISCO "VPN Client" connect from my PC at home for my work PC.

    Then, I get a message:

    Validation failed for C:\WINDOWS\System32\VSINIT.dll

    Any ideas?

    Martin

    Hello

    Run the checker system files on the computer. Link, we can see: Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe): http://support.microsoft.com/kb/310747

    Note that: if he asks you the service pack CD, follow these steps from the link: you are prompted to insert a Windows XP SP2 CD when you try to run the tool on a Windows XP SP2 computer system File Checker: http://support.microsoft.com/kb/900910 (valid for Service pack 3)

    If the steps above is not enough of it please post your request in the TechNet forum for assistance: http://social.technet.microsoft.com/Forums/en/category/windowsxpitpro

  • Professional Windows Vista crashes when you use Cisco VPN Client 5.05.0290

    I have a Dell Latitude E6400 Windows Vista Business (32 bit) operating system. When I go to turn on the VPN client, I get invited to my username / password and once entered, the system just hangs. The only way to answer, it's a re-start. I took action:

    1 disabled UAC in Windows
    2 tried an earlier version of the VPN client
    3. by the representative of Cisco, I put the application runs as an administrator

    If there are any suggestions or similar stories, I would be grateful any offereings.

    It IS the COMODO Firewall with the 5.0.x CISCO VPN client that causes the gel. The last update of COMODO has caused some incompatibility. I tried to install COMODO without the built in Zonealerm, but it is still frozen. The only way to solve it is to uninstall COMODOD. Since then, my CISCO VPN client works again...

Maybe you are looking for