Closing of ports & no time closing of LMS 4.2

Similar Questions

• Setting up Time Capsule 3 to

  Advice please, I'm a little confused as to how set up my Airport Time Capsule to do what I want it to do.

  I currently have:

  -A "Superhub" recently installed offering fast home Internet access via a cable fibre optic supplier.

  -J' bought a Time Capsule from Apple before hand and want to put it up to do the following:

  -Connect two external hard disks accessible storage from my Mac Mini and MacBook (USB connection).

  -To connect a USB printer accessible to these two computers, (more than the iPad and an IPhone).

  (Meanings attached to the ATC via a USB hub)

  -Use 3 TB storage in ATC as a backup Time Machine of Mac Mini and MacBook.

  I understand that ATC must be connected on the beautiful via Ethernet to the WAN socket cable to a plug on the hub.

  I'd be grateful if someone could please explain/point me to an explanation that describes how to set up my Mac Mini ATC in order to achieve the above requirement clearly and in simple terms.

  Thank you very much

  Before you begin, you must understand that to connect a printer to the USB port on the Time Capsule, as the iPhone and iPad iOS devices will NOT be able to print to the printer?

  That being said, a third party application like Printopia pourrait be able afford this, but there are no guarantees, and our ability to help on such things is limited, at best.

  The reason is that iOS devices required an AirPrint -compatible printer that connects to a wireless network. In other words, Apple takes the 'Air' in AirPrint very seriously.  Please take a look at this support document Apple for more information on AirPrint compatible printers.

  On AirPrint - Apple Support

  Order of the day. Depending on the brand and model of your printer, your Mac may or may not be able to print on a printer connected to the USB port on the Time Capsule.  Unfortunately, Apple does not provide a list of compatible devices in this regard.

  So, while we provide some tips on 'how to' attempt to put in place, we cannot tell you if it will work or not. Not sure how well... or if it will work until you try it on your own network.

  We will try to help, but normally, you could get information on how to set up your printer by people of support for your printer, not to Apple.

  Regarding the connection of two hard disks and a printer to the USB port of Time Capsule, this will require the use of a powered USB hub which manages devices USB 4 or more.  The problem... some powered USB hubs will not accept a USB to operate simultaneously, so you wouldn't be able to print, for example, while you have been back up data on a hard drive connected to the powered hub.

  So, you will need to check with people of powered support for your hub to ensure he will allow the simultaneous for USB devices use.

  If you want to move forward, we can help get the set up time Capsule and work with your Superhub, but our ability to help printers and hard drives may be limited.

• Best config Time Capsule - Airport Express

  Hi all.

  My home network at present are as follows:

  -My ISP, with a disabled Wi - Fi router;

  -Mac and PC connected via ethernet cables using the router's LAN ports.

  -Airport Express (WAN port) connected by ethernet to a LAN port of the router that gives Wi - fi in the House: note that the router and AirPort Express are in different rooms (router: bedroom, AirPort Express: living room)

  I want to add a time Capsule to my network, but I want to put in the living room, where the Express is at the moment. I don't have a single cable ethernet connecting the bedroom to the living room because there is not enough space in the walls of two sons.

  What I would do is:

  -Time capsule in the living room, connected via an ethernet cable to the router, generating the signal Wi - Fi;

  -AirPort Express connected by ethernet to a LAN port of the router, which extends signal Wi - Fi in the bedroom.

  This configuration can work? And how? Should I use the same SSID?

  If this is not possible, my only option is to connect the Time Capsule via ethernet to the router and then connect the WAN port on the Express to a port of time Capsule, right? Would not be my best installation in the House, but if it's the only one that works, I'll go with it. If I didn't have the problem of the single cable connecting the two rooms, everything would be super easy. Extending Wi - Fi wireless is not in my case, having this second wired option.

  Any other suggestion is appreciated!

  What I would do is:

  -Time capsule in the living room, connected via an ethernet cable to the router, generating the signal Wi - Fi;

  -AirPort Express connected by ethernet to a LAN port of the router, which extends signal Wi - Fi in the bedroom.

  This configuration can work? And how? Should I use the same SSID?

  Of course, it works very well. Download Time Capsule set up and running using Apple "Installation Wizard", and then reset the Express back to the settings by default and set up using Configuration Apple "Assistant" as well.

  The wizard will affect automatically the same SSID and password to the AirPort Express, which uses the Capsule, so by default, you will have what is called a "mobile network". For the configuration, I would recommend that you temporarily connect the Express to the time Capsule using a short Ethernet cable to spare before you run the installer... no matter how long will do.  Connect from a port LAN <>- on the Time Capsule to the "O" in L'Express WAN port. Once the Express is set up, you can move it to the location of the router to establish Ethernet connection here.

  If for any reason, you want the AirPort Express to use a different SSID as the time Capsule, you can use AirPort Utility to go back and change the SSID (and the password as well if you want) on the AirPort Express Terminal.

• How to configure a printer wireless connected to Time Capsule?

  I just bought a printer HP Color LaserJet Enterprise M577z MFP Flow. It has capabilities of wireless printing. So far, I was able to connect wirelessly to one of my MacBook Pro computers, but only by having the printer create an Ad - hoc network that allows up to 5 devices to connect to the printer. But that of not what I want because every computer should manually disconnect the Wi - Fi network, connect to the Ad hoc network, the print job and then reconnect to the Wi - Fi network whenever a print job is required. It is very difficult and frustrating.

  What I would like is striking is the printer act like a network printer by wireless connection to my Time Capsule. I can't connect the printer to the USB port of time Capsule because they are far away from each other, and I don't want to use cables throughout my place. But I have no idea on how to do it because I can't find this option in the menu of the writer or configuration of the United Nations the HP utility software.

  I hope someone here could help me, please. Thank you!

  I have an Epson printer, so some of my experiences may or may not apply.

  I also have a time Capsule, and my printer and Time Capsule are far apart.

  My current configuration looks exactly what you are looking for: a wireless network provided by Time Capsule than all my Apple devices to a wireless connection, and my printer connects to the same wireless network.

  When I first bought the Epson printer, I needed to connect it to the Capsule of time via a USB port.  This sounds as if it were true for you as well.  So, for this very short period. I moved the printer via the USB port next to the printer, the connected Time Capsule, made the setup and then the printer recognized my standard wireless network.  I've returned to steady state, which I use now, with the printer and the far (actually on different floors) Time Capsule.

• retrieve the time backup machine for new ssd internal

  I had to replace my internal HD on a 2012 end iMac, so I went to SSD.

  I had saved my first system and files in Time Machine before that.

  What is the process of a) formatted internal SSD new and b) recovering the original of external backup Time Machine?

  As I have to reseal the iMac just to make it work, I don't want to have to open it again to play with the new SSD!

  Hope that you already have a boot USB OS X in hand disc (I always have a copy must have on hand).

  Plug the USB into the USB port and Time Machine,

  by key pressing 'option' as soon as 'chime' begins.

  You can choose the selection of the boot drive.

  OR

  If your SSD does not start on her file (e.g. blank) - it should start automatically via the USB.

  (a) - Yes, using "disk utility" - in the menu bar superior, to partition the drive (GUID) first

  (b) then choose 'continue' to install the OS X - at the end, you will be asked few options - recover via Time Machine.

  After the restoration, you can run a few updates so that the system will work like the old set up.

  Most of the software should work, but somehow, some software required "activation key" again.

  Those notorious - Rosetta Stone (language). -J' had to communicate with them, uninstall the old drive first.  Microsoft Office can be too fickle.

  Make sure that OS X are the same version (you can't have 10.11 on Time Machine, try using the boot USB 10.10 disk) targeted installed OS X must be the same or more recent than the OS X version of the time Machine.  For example, if your Time machine backup contains 10.10, then you can either use drive start USB 10.10 and 10.11 for the restore process.

  Sam

• can I use an external hard drive LaCie Raid time capsule?

  I am trying to hang a LaCie Raid to my Time Capsule for additional storage. I don't see the LaCie. Thanks in advance for the help.

  Support Apple mentions that you can plug a simple USB to the port on the router from the airport, or several readers if you use a powered USB hub.  There is no mention of Raid type disk, which I interpret as meaning that the RAID is not supported by the firmware on the USB port on the airport.

  Uses for the USB port of Time Capsule, AirPort Extreme, AirPort Express - Support Apple Airport

  From my experience, the Raid type drives are not recognized by the USB port on the Time Capsule or AirPort Extreme.

  Even if the RAID drive was recognized, probably would NOT ever want to connect a RAID stack on the port.

  The reason is that the port is USB 2.0 only... and due to the limitations of the processor in the airport router, the port runs at half the speed of a USB 2.0 on a computer. Thus, it would be incredibly slow with this type of installation.

• Port USB USB-6009 bug

  Hello

  I would ask for advice. This is the scenario in a few words:

  We have a new project already written in LabView to control a mass of a machine from K - Ar spectrometer and record two analog channels of an NI USB-6009 device data. Rate is the maximum: 24 kHz per channel.

  After deployment, we started to get a DAQmx driver strange error, but only when we used a certain port on a DELL laptop (this port was a 2.0, the other SS 3.0). USB ports did not create this error. After several days, when we realized, the error is not in our LabView code, we found this conversation in the forum:

  http://forums.NI.com/T5/Multifunction-DAQ/USB-6009-overflow-error-on-continuous-mode-after-restart-o...

  We believe that it would be strange to tell the client that "Please do not use this device ON this port, because it's a little bug...". ", then

  We were very happy, because this DAQmx property through the property node solved the error of USB port (see attachment file).

  However, a few days ago, we got an unexpected behavior: our program during a mode over DAQ completed the acquisition of a few seconds earlier, then he should have done. There was no signal error, but only this strange behavior, like in the "task done? VI DAQmx reported "too early."

  Since this 'error', we could not reproduce it yet (so far), we have used the program several times without problems via this "slow" USB 2.0 laptop port.

  Well, I'm always interested in a definitive solution of OR to fix this in their products and in the DAQmx driver. I heard many colleagues that they run into this bug of USB port several times when they use NI HWs, and this problem is very annoying. I know that the solution usually easy: plug the device into a different port. But I think that these materials should run flawlessly on the USB ports on all THE...

  Hi man,

  If you found your own workaround by plugging the USB module to another USB port.

  You said the accures only mistake on the special USB computer ports. This can be caused by an internal hub used in the computer. USB hubs may cause difficulties with hardware OR.

  Do you have other questions?

  Kind regards

  Melanie

• 2D table are displayed in a table, 1 row at the same time

  I use a loop to read a serial port 40 times and display the values in a table of 40 lines and 5 columns.  I have auto index out of the loop For to build the string 2D array. The problem is that the serial port takes too long to respond and the VI takes about two minutes to display the values in the table because it do not do until that loop to complete its 40 iterations. Is it possible to display every iteration it runs? I mean, pass the value of the iteration 1-the 1st line of the table and then make the 2nd iteration, pass its value to the 2nd line of the table and so on? Thank you very much! (Happy Christmas to those who celebrate the it)

  Yes.  Put your picture inside the loop indicator.  Use the Array function to build to build your table.  Insert the table into a shift register.

• How to find the mobile average for perticular time step for the same time series

  Hi all

  I'm new in labview and I have a question. I have a huge text with the value of different pressure of various ports.

  I do the VI in which all first I read the text file and identify the column of perticular port. In this column, there is pressure value 32768.

  Port of Port 102 times Num Port 101 103... Port 532

  0         1

  2 0.001

  .          .

  .          .

  50 32768

  And reading this all takes 50 sec and I divide this reading in 4.5 sec... There are in all 4.5 sec 2969 values...

  Now, please check the attached VI... I am able to find the average value in step 12 2969 value time...

  Now, I want to do is to find the average value of 2969 (2970 to 5938) values with time of 12 steps and so on up to 32768. It is 11 times in the series...

  So anyone can change my VI?

  Thank you

  Hello

  Thank you very much. It's the perfect VI that suits my needs.

  Thank you again... Have a great day ahead.

• Need to monitor the media port use on 8510

  Info on MCU:

  Cisco TelePresence MCU MSE 8510

  Serial number SM021XXX

  Software version 4.4 (3.49)

  Build 6.18 (3.49)

  Availability 6 days, 22 hours, 15 minutes

  It is a HD blade that is configured for the ports of 40 media

  I have to be able to look at the use of the port over time to know when we have exceeded the maximum number of ports and the appellant has been abandoned to the audio only

  Thoughts?

  --

  Dan

  You can find exactly what you are looking for in the event logs.  I just maxed out our 8510 by a participant, the same fall first one I added in the test that matched my allocation of port instead of going 1-sending video of my test results are below.

  30330	17:40:09.423	CONFERENCE	Info	Unable to send the video to "Patrick Sparkman" - allocation exceeded
  30331	17:40:09.536	CONFERENCE	Info	now able to send the video extended to "Patrick Sparkman"

• LMS Reporting errors

  Hi all

  I'm working with a new client that use a bit of an outdated LMS. They have all kinds of problems with the declaration of completion of their e-learning modules.

  After many conversations with the LMS vendors, I was informed that the statement errors are caused by a session time-out the LMS's, where if 20 minutes past where the SCORM does not somehow contact or "ping" the LMS, it will be time.  This means that the learner went 30 minutes doing an e-Learning module, the last 5 minutes which is a quiz, but the results of the quiz and completion are not getting the LMS spokesperson because the session has expired before you start the quiz.

  During the content slides (no quiz), so I need to find a way for the SCORM module interact with the LMS and perpetuate the session without changing the structure of the module.  I don't like the idea to follow the slides in the completion of the report (because there are a few branches, and not everyone discovers the same number of slides at the end of the module). Can someone suggest a simple solution for this?

  Thanks in advance!

  Hannah

  'Send the data on each slide' should do what you need. If nothing else, CP should send "resume data" (since you have 'Never' checked ' on each slide.)

  If sending data on each slide is indeed applicable only to the slides that send interaction data (which I doubt), then you could possibly workaround by including a next button on each slide with a value of 1... so that the partition should be sent to the LMS.

  However, who will surely shake your score real quiz.

  May be worth a try just to see if it solves or proves the issue...

  How can you be sure that the option to send data only applies to the quiz on the slides?

  Cause if you look at configure it button options next to SCORM 1.2... who has a "SendTrackingDataAtEnd" model which is exactly to send all the data at the end... which involves with design 'Default' data are sent across, not only for the quizzes...

• Can I use USB 2.0 drive into a USB Port on my computer 3.0 portable g6-2235us

  Can I plug in a device of USB disk 2.0 to a USB 3.0 port on my computer laptop 2235us g6?

  Hello

  If it is a new laptop, the USB ports can be a little tight.  Try to insert and remove a device which plug into USB 3.0 ports several times and then try again the USB 2.0 device.

  Kind regards

  DP - K

• Close TCP leaves the connection open

  Hello guys,.

  I use an ethernet connection to query the data of 2 units of acquisition of sensors.

  This request is motivated by a second timed loop period 30.  As this rate is very low, I have the close connection and reopen it each time.

  I try to connect to the device via the same 2 ports each time, 50,000 and 50 001.

  I get the error message that the connection is already used for a close connection of TCP executed without error before.

  The network view TCP tool monitor gives me the screen following [network_connections.png] when I run w/o specifying the local port. It seems that the previous connection are not adequately closed and are always in the TIME_WAIT state. This list is continuouslly prices, leading to errors of networks. (For the units IP address is 200.0.4.152 and 153)

  Could you please help me on this?

  Thanks in advance

  Kind regards

  Bruno

  Hello

  This seems to be a common behavior:

  http://digital.NI.com/public.nsf/allkb/119D334B8B78732E862574E1006D1839

• Connections Rs232 multi

  Hello

  I have developed a small test bench equipment controlled by RS - 232. The trial will be done with TestStand and LabWindows. I want to use several RS-232 ports that communicate with Labwindows (dll). I want to know if is possible to keep these connections open simultaneously, or can not do this. If we succeed, do you recommend this method or it is best to open and close a connection whenever I order the material.

  Thank you

  Hello

  I have a Setup with 32 serial ports (via maps OR). As a general rule, all available instruments are in communication with the software, timer controlled (note their status on a time scale of 10 to 60 seconds). This should answer your first question: Yes, you can have several ports simultaneously.

  Regarding your second question: in my application, ports are kept open until the instrument is closed. However, I can not answer, if it is better or worse than the reopening of the port each time...

  Hope this helps a little,

  Wolfgang

• Rogue Hub/Switch blocks?

  Hello

  I noticed MAC addresses with a 0000.0000.0000 on some of our switch ports in a particular building.  It turns out that some end users have been connect hubs personal/no authorized and/or cheap 5 ports switches in our network on these interfaces.  We have disabled the ports manually, then of course end users called the helpdesk informing us that they have lost network connectivity.

  PortFast and BPDU guard is enabled all leading edge devices.  However, given that these are switches and concentrators cheap I don't think they make same STP.  In order to have custody BPDU err - disable the port isn't our fix.

  So, is there another way to block these devices?  ACL?  MAC filtering?  Can you just block MAC 0000.0000.0000?  Maybe someone can explain what that means MAC 0000.0000.0000?

  I am aware of the port security, and which is currently in the works, but there the hope of a quick solution in the meantime.

  Thank you!

  -Brett

  Depending on what type of switch you have, you have dynamic inspection of arp, where you record only trust mac on the database of the switch and the switch will reject any other mac connection. Port security is another option, allow a maximum of 1 mac on the port, but the problem will persist that connect a hub + computers, the port will be closed and you will need to reactivate the suspended port each time.

  Also here is a good post to review an ACL

  https://supportforums.Cisco.com/message/3727181#3727181

  -Tom
  Please evaluate the useful messages