CM500 and CM600 public or private IP assigned to the router?

Similar Questions

• Configuring the network for windows7 and computers portable XP with printer connected to the router

  Computer laptop windows 7 works with the printer lexmark that is connected to the router, but the laptop XP who worked with the printer can't find using the "add a Printer Wizard. Two portable computers connect to the internet O K

  Printers configured in this mode are better develop a fixed TCP/IP address.  Your printer manual should tell you how to do this.  In general, there is a 'Settings' menu on the printer where it can be defined.  The IP address should usually have the first three digits than other devices on the subnet (for home networks it would be something like 192.168.1.x) and the final number should be unique and apart from the DHCP numbers range that your router would normally assign (see the manual of your router).

  HTH,
  JW

• L2l VPN with public ip of the router and firewall with private IP

  Dear all,

  I have a requiremnt for site to site VPN configuration but the firewall on the remote end is not obtained public ip, public ip address is termintaed on the router. Please find the attached diagram

  LAN--> Firewall - privateip--> router-publicip - ISP

  How can I set up the site to site VPN tunnel, enjoy emergency assistance

  Thanks in advance...

  Mikael

  You can configure static NAT for 1:1 for the SAA outside interface with a spare public ip address of the router address.

  If you don't have spare public ip address, then you must configure static UDP/500 and UDP/4500 PAT on the router and enable NAT - T on the SAA.

• Configure the router WRT54G with the PUBLIC IP address and use the DHCP protocol for internal computers

  Hello

  I have a service online Internet with 5 public IP addresses.

  The router and the AP are connected to a switch.

  I would like to set up a WRT54G Router with a public IP address and use DHCP (with private ip address) for the computers that will connect to the AP.

  That the AP is connected to the switch, it is possible that the other wired computers that are connected to the same switch can get an IP from the DHCP?

  Thanks in advance

  In this case, the routing is automatic.

  WRT54G configuration:

  WAN:

  Internet connection: static IP address

  IP address: 180.X. X 170

  Subnet mask: 255.255.255.248

  Gateway: 180.x.x.x (Ex: 180.x.x.1)

  DNS: servers your ISP DNS

  LAN:

  The IP address of the router: 10.10.10.1

  DHCP range: 10.10.10.100 of-online 10.10.10.200

• No saved reports - no Public Option / private

  I created a new application with several interactive reports.  However, when my users click on save report, there is no option to make the saved report, public or private, as indicated in the documentation.  I have it configured incorrectly?

  Thank you.

  Under the documentation:

  Tip:

  To save a public report, the developer must select Save Report Public must be selected under include in the Actions Menu on the report attributes page. Developers can also apply for authorization scheme to enable or disable save the Public report. See "Customizing the search report interactive bar".

  So, it is possible that you don't have this game in your configuration of application report...

  Thank you

  Tony Miller

  Software LuvMuffin

  Blog: https://apex1.revion.com/pls/apex/f?p=217:1:P1_ARTICLE:

• The router RSV4000 does support multiple public IP addresses

  I have a client who has a RSV4000 router. The customer also bought a block of 5 usable public IP addresses. I need to be able to assign these public IP addresses for printers, either by configuring a static IP address on each printer directly or through mapping of intellectual property or any other method. Made support for RSV4000 using several treats public IP and if so what configuration is required in the router for printers to be seen by the outside world.

  Hi Winston,

  Thank you for posting. The functionality you need is one-to-one NAT, who does not have the RVS4000. Please watch the RV042 or RV220W for this feature.

• Can I have a home network that is a mix of wired and wireless, and be able to use devices connected to the pc without wire while working from a pc cable and the network map will show all?

  I have a router Linksys Wireless-N-large band with 4 catches on and 1 ethernet to my internet modem cable. Wireless connections work well in my relatively small house. Rather than to buy several USB wireless receivers, I thought just to use the ethernet # 1 and plug it into my computer close to the router.

  Hello

  Any computer that can connect to the router (wire or wireless) can be part of the same network.

• Since the reinstallation of Windows 7 I have same Wifi access so my laptop and I heard a small noise from inside the Tower

  Since the reinstallation of Windows 7 I have Wifi access even if my laptop and tablet of my wife can become if the router is OK. Also, it restarts or freeze without reason. Sometimes I hear a metallic noise inside the Tower, but not always. My friend suggests a hardware problem, but has no suggestions on how to solve it.

  Original title: Windows

  Since the reinstallation of Windows 7 I have Wifi access even if my laptop and tablet of my wife can become if the router is OK. Also, it restarts or freeze without reason. Sometimes I hear a metallic noise inside the Tower, but not always. My friend suggests a hardware problem, but has no suggestions on how to solve it.

  Hello

  After a reinstall of the operating system, you must reinstall the latest drivers from your computer manufacturer's website:

  Go to the website to make your computer > Driver and Software Support Section > search your computer or hardware model number > then your operating system > locate the correct drivers > download and install.

  ________________________________________

  And you do not tell us why you did a reinstall and if there reboot/freeze before you did this reinstall.

  FYI: Desktop computers normally are Wi - fi unless you install additional hardware for this.

  ________________________________________

  Noise inside a desktop computer can be caused by fan/s or harddrives about to fail.

  Go to the website of your computer manufacturer > search your computer specifications > know brand of hard drive > access the Hard Drive manufacturer's Web site > find and download hard drive Diagnostic software and make a record of start of it on the computer that you use to get here, following their instructions > test your hard drive...

  See you soon.

• Hi I have a problem to connect on wifi I have reset all the setting ang simultaneously press the home buttom ang poewr but not wrking buttom, I can't and on the router because I was on a public area as hotel thank you

  I have 5 16 g model A1428 phone

  FCC ID * A IC * A IMEI; ***

  I TRY TO OPEN MY PHONE TO CHANGE THE BATTREY AND REMOVE THE LCD CABLE TO CHANGE THE POWER ON SWITCH, BUT UP TO THAT ONLY TO REMOVE THE LCD SCREEN, I GAVE ALL MY BECAUSE IS DIFFICULT... WHEN I PUT I CAN NOT CONNECT TO WIFI.

  I TRY to RESET all THE SETTING or RESET or PRESS TOGETHER HOME BUTTOM AND POWER SWITCH ONLY MARKET THE ROUTER NETWORK I can't DO it BECAUSE it OF in CRUISE BOAT or in public space...

  Thank you!

  ALFREDFROMTAGBILARAN

  < personal information under the direction of the host >

  Please do the following and after each test to see if the problem is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Please see recommended settings of WiFi routers and Apple access points
  4. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  5. Settings - WiFi - < network name > - Click on forget network - do a restart forced 4 and then again add the network
  6. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  7. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  8. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  9. Backup the device to iTunes - restore as NEW (no backup) using iTunes - see if solves problem - if yes - restore backup
  10. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• Port of public to private ip address mapping

  I'm trying to change a netopia router in Bridge mode and put a UTM5 behind the bridge newly netopia.

  I see in the netopia there are several IP cards that take some of the assigned public addresses and direct them to addresses internal ip. I need to know if this is possible on the UTM5. I added the other public IP addresses on the Wan as well as the default.

  I need to do the following (example used IPs):

  64.129.001.001--> 192.168.1.151
  64.219.001.002--> 192.168.1.152
  64.219.001.003--> 192.168.1.153
  etc...

  Someone at - it any information on how to get this feature within the UTM5

  Hmm ok, thanks for the info.

  From what I see and read, when the Netopia is placed in bridge mode, it erases all the Routing and IPMaps out unfortunately, so why I think that the UTM5 should do the mapping.

  Granted I'm not very familiar with the characteristics of the Netopia and this is an old old installation. Just buying some time before the line is replaced by a more stable connection.

  UPDATE:

  Looks like that the Netopia is mapped correctly because I deleted an IPMap of the device and address was still ping successfully at least, so I set myself follows her and hope that it works:

  

• 2600 NAT outside public to private inside addresses

  I would like to put servers with private addresses at disposal of guests (with public addresses) on the other side a router. Can someone give me a pointer?

  TIA

  you want to configure static NAT.

  Suppose that 10.10.1.5 is the server inside and 193.234.211.12 is your free external IP. Joanie configure this line:

  ' ip nat inside source static 10.10.1.5 193.234.211.12.

  And all those who will have access to the external IP address will go to internal (static nat)

  see you soon

  Robert

• The IP address private VC directly to the public IP address

  Hello

  I'm a bit puzzled as to why a specific call, I saw worked for a couple of guests and wonder if there was no change in the situation in the H.323 protocol that allows a form any NAT crossing built natively into the codec without involving and external gateway function.

  the reason I ask is the following

  I got a call from a customer with a codec on a private no routable IP to my system that is located on a public IP address, the client had no details of NAT configuration in the endpoint and was able to call my system directly without issue by calling directly to my public IP address.

  historically now if I had a system on a private IP address was sitting behind a NAT, I expect that the public system IP would see no routable IP address of the H.225 message and try to answer the private IP RTP media that would not go through, it does not seem to occur.

  the call that I have lived seemed ends without problem, media flowed in both directions.

  My endpoint is a Cisco edge 85 on the version of the firmware F9.x

  the other codec parts is an 85 edge on the version of the firmware F9.x

  My codec is on a public IP address that is completely open to the H.323 ports

  the other codec parts is on a private IP address.

  while I can't call the other party, the other party may call for me, and I wonder how it worked, taking into account the fact that there is no gateway service aware H.323 in the call, either a VCS or aware firewall H.323.

  Experience, firewalls and other gateways outside of Cisco, Tandberg, Polycom, have struggled to deal with the new H.323 version, again this is why I'm puzzled as to why the call worked.

  I did a bit of reading on the new version of H.323 and noticed the option multiplex logical channel, however on a call where I saw this apparently works again of a life-size codec for a Codian MCU 4505 shows no sign of this logical channel multiplex, unless that is named differently in the newspapers that the ITU document calls the function.

  greatly appreciated all all all the answers, I don't understand exactly how the firewall impact VC calls.

  Thinking with portals

  The MXP has NAT builtin functions. Please take a look at the guide admin 9.x:

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/MXP-series/F9/administration_guide/mxp_series_administrator_guide_f90_excl-full-menu-structure.PDF

  The description of the NAT setting is on page 77.

  EX series admin guide http://www.cisco.com/en/US/docs/telepresence/endpoint/ex-series/tc6/administration_guide/ex-series-administrator-guide-tc62.pdf has the same details on page 63.

• Specifying the NIC Public private network cards during the Installation of the grid

  Version: 11.2
  Operating system: Solaris
  
  We will install the 11.2 grid.
  These are IP addresses, we will allocate for the Public sector and private Interfaces
  

  bge0--->10.80.143.214 ---- for public network (Subnet mask 255.255.255.0 )
  
  bge1--->172.132.116.81 ----- for private Interconnect (Subnet mask 255.255.255.0 )

  But, during the Installation of the grid, the grid Setup will ask only those IPs with the last byte 0 as shown below url

  bge0--->10.80.143.0 ---- for public network 
  
  bge1--->172.132.116.0 ----- for private Interconnect 

  http://4.BP.blogspot.com/_0ut-UEg1S3k/SqI3w1QgVLI/AAAAAAAAA1w/Zq6jwWWh_48/S1600-h/8.PNG
  
  The installer actually displays the "subnet". But Public and private NIC of the subnet is 255.255.255.0
  Is this really? Why the installer of the grid is not inviting the real IPs allocated to networks of Public and private?

  Hello
  Litte Note:

  Why the installer of the grid is not inviting the real IPs allocated to networks of Public and private?

  The cluster runs under Network (e.g. 10.80.143.0) under any one or two IP, because several IP addresses of the network in question can be used (it is about scalability and availability), you install a cluster it show the networks used, not used IP (this occurs in any system of cluster, you must specify the network).
  Kind regards
  Levi Pereira

• Oracle synonyms: public or private

  The LiveCycle installation instructions specify that for the creation and initial filling of the database THESAURUS 'CREATE' privilege is necessary. I presume this means LK who actually will use to create synonyms. The DBA is now whether these synonyms will be public or private, and I can't find in the documentation. Could someone advice?

  Can you share the URL where it is documented and the version of database you set up? In line with the preparation for installation , the Oracle user account must have the following privileges:

  • CREATE SEQUENCES
  • CREATE VIEW
  • UNLIMITED TABLESPACE
  • CREATE TABLE
  • CREATE THE CLUSTER
  • CREATE SESSION

  ~ Vishal

• Public vs private

  When I publish my application through the creator of folio tools gives me the possibility of Public or private. Can someone explain exactly what they mean? If I put it to the private sector can I still share it with customers? They have to sign in their applications of Content Viewer with my login or can they still use their own? What about the Public? Who can see it then?

  I assume that these decisions have no impact when I eventually send the app to iTunes, or are they?

  When you publish a folio as private, the folio is published on the service of distribution (Akamai servers rather than acrobat.com servers), and it is available only in the viewer of the iPad. The private folio appears in the library without the blue band. When you publish a folio as Public, you make it available to all of you who have your custom Viewer.