Color is stuck on red with a low opacity

Similar Questions

• Windows Media Player 11. Stuck on red color picker

  Windows Media Player 11. Win XP SP3. Color picker does not and the color is stuck on red and can not change the color or tint on the sliders. Looked in the registry for all the settings but nothing works? Tried to reinstall but still the same...

  Windows Media Player 11. Win XP SP3. Color picker does not and the color is stuck on red and can not change the color or tint on the sliders. Looked in the registry for all the settings but nothing works? Tried to reinstall but still the same...

  I found this solution on an Avast forum (seems as if some Avast users have this problem) and it worked for me.

  Open the dialog box run (twice) and then paste into the pressing next OK after every time:

  regsvr32 jscript.dll

  regsvr32 vbscript.dll

  I did a registry backup first - just in case - but now my WMP is back to normal (black)

• HP Envy 4504: Envy 4504 photo prints too red with print quality = better

  Hello

  I hope someone can help.

  On my HP Envy 4504 photos are printed OK print normal quality, but when the print quality is set to best photos are printed to the red. In addition, with DPI Maximum printing photos are much too red.

  This takes place two times printed on paper Normal and on Photo paper

  With the GIMP, I tried to make an example of how a photoprint looks like.

  I made the example by changing the color Balance: Red cyan - about + 40:

  (my GIMP is Dutch...)

  

  Here is the result:

  LEFT: Photo printed in normal quality; Photo on the RIGHT printed in better quality:

  

  I have already completely remove the software HP Envy and did a clean reinstall. No change.

  I have print-head - cleaning cycles (2 times); color of HP-testprint strips looks very good: all are strong in alignment is correct

  Unfortunately: No picture change in best quality still too red.

  The ink levels are okay.

  Any suggestions what is wrong and what can solve this problem?

  Thank you for your support

  Kees-Jan Timmer

  Hi @Kees-Jan,.

  Welcome to the HP Forums!

  I noticed that your HP Envy 4504 prints photo is too red with print quality = best on Windows 10 operating system. I'm happy to help you!

  Where a setting is disabled, with GIMP, have you tried to print photo quality with other programs? If so, what happened?

  You use genuine HP cartridges or refills?

  None of your ink cartridges are low or empty?

  In the meantime, please make sure that all the steps in this guide, fixing poor print quality are executed. And let me know what happens!

  Thanks for posting and hope to hear from you soon!

  If this, or one of the posts on this thread, helped you to solve the problem, please click 'Accept as Solution' said post. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

• Can I solve the problems of alignment is to have my Color LaserJet CP1518ni? Red will not line up.

  Can I solve the problems of alignment is to have my Color LaserJet CP1518ni?  Red do not line up, I installed the latest updates, etc.  Calibration does not help.  The printer is only a few years old.  What gives?

  Hi threre, I just work on HP CP1518ni a client with this same alignment problem as most of you are describing. I went through some process and I think I found one that works... If all goes well it will work for

  You too.

  Things I tried before hand... also this machine has all the toners brand HP 90 + life on each of them.

  -Calibrate - has not fixed the problem (tried once)

  -reset the NVRAM - did not problem

  -removed and inspected print cartrides (no problem found), re-installed - fixed no problem

  The 'fix '...

  First, go to the HP website and download the firmware, make sure you only select the right operating system

  you are using. (for me it was Windows XP) Also the requirements of course read, I think you have to

  have with XP SP2 if it perhaps questions, always read the instructions before doing the firmware.

  Here is a quick link to the CP1518ni...

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=3422472 & LC = on & CC = US & DLC = in & lang = to & CC = US

  Then, assuming you have the appropriate printer driver installed, double-click the utility you just downloaded and select the CP1518ni from the drop-down list. Now, press the button 'send the firmware '. It will be

  Take a few minutes so just let it do its thing. After that she did try to print something, for me it was NOT fixed.

  Now you want to calibrate the device, maybe 2 or 3 times, on the control panel scroll to the right until

  you see "systemsetup" press ok and scroll to the right again until you see 'print quality' and press ok.

  the first item in this menu is press "calibrate color" ok, now he's going to say 'calibrate now' and press ok one

  last time. It will start the calibration process. Then he did print something new to see how he does.

  for me I had to do the calibration process twice before the quality was normal again.

  Good luck, hope this helps some, I read that some printers still presist even after this process.

• How can I customize the color of the pointer (red or green) mouse in Windows 7?

  I'm trying to help a colleague with a visual impairment to customize Windows 7, it can navigate more comfortably.

  She would like to change the color of mouse in red, green or yellow.

  Try the instructions here http://windows.microsoft.com/en-CA/windows7/Make-the-mouse-easier-to-use

• HP Envy 5530: HP Envy 5530 told to replace the color cartridge, even after replacing with a new one.

  HP Envy 5530 said to replace the color cartridge, even after replacing with a new one.  Printer is 1 year old and I replaced the cartridges several times over the past year.  I am enrolled in the program of HP ink.  I can run the printer mode single cartridge using a black ink only and it works with my pc XP, Ipad, Chrome pc and mobile phone.  My pc win 8.1 will not print anything other than a test page.  Printer on the pc file lists always attention required when you try to print from the pc win 8.1.  I believe that the problem may be related to surface of cartridge for printing inside the HP envy heads 5530.  This part is available for purchase, and if so, where?

  I found a work around.  On the pc win 8.1, it seems that the print request must see a reset of the HP envy 5530 to print mode single cartridge.  I just start the pc and then reset the printer by lifting the hatch for the print heads.  That's all.  Once this is done, the 'attention required' message goes to the loan and it is able to print.  It will open a window, which suggests you add the color cartridge, but it will disappear when printing.  Simply open the door once and you can print until you turn off the pc.

• MUTE button on Pavilion dv6z 3100 stuck on Red

  Hello

  Mute the button on my laptop is stuck on red, even when he is not dumb.  S/N is CNF0391Y54 and the number of product WV813AV.  Model number dv6z 3100

  I know from reading other messages that I should reinstall the audio driver, but I'm having a difficulty in finding the right driver.  Could you get it someone please let me know the link for the correct driver?  I hope I included enough information.

  Thanks for any help.

  Hello

  Try the following.

  Download IDT Audio Installer on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp50501-51000/sp50595.exe

  One time finished, open windows control panel, open Device Manager and open sound, video and game controllers.  Right click on the IDT device and select uninstall - also, you should get a command prompt to delete the current driver, check the box to enable this and then proceed to uninstall.

  When finished, restart the computer and let Windows load completely.  Open your download folder, right-click on the IDT Installer and select "Run as Administrator" to launch the installation.  Once done, restart the laptop.

  Kind regards

  DP - K

• Z820 - button Power LED blinks 4 times (red) with beep... bad card (Quadro 4000) graphics?

  Hello

  My Z820 at the office is suddenly having a few hardware malfunction.

  When I turn on my machine, the PSU/system fans don't rev and the Power LED button flashes red with a beep 4 times.

  According to this page of troubleshooting, this indicates a faulty PSU on the new UEFI computers:

  HP desktop - computer does not start and emits a LED or a beep Code

  Section "code beep and LED descriptions.

  Get the exact model of LED as the example of "power failure".

  Then, I got a new power supply replacement. I still have the exact same model LED and beeps...

  So, I have drawn deeper and found that when I removed the Quadro 4000 card graphics and then put on my machine, the power button LED is lit in blue (led code ' computer-S0 (normal operation) "") and all the normal spin fans.

  The Quadro card seems to be the culprit...

  Unfortunately, I have no alternative graphic card laying to verify this around, I'm waiting for a replacement of the graphics card (via HP service) to arrive tomorrow.

  Is it possible that the power LED button code (4 times red with beep...) has nothing to do with a bad power supply and that my Quadro is bad?

  Dries

  Dry... that Z820 has been giving you headaches.

  Many fault codes have not changed since the previous workstatons.  I hit this series of beeps of error in the past, and often doesn't mean that the power supply itself is the cause.  It can be a hardware device to the bottom of the chain causing a power surge to power, triggering his "crowbar circuit: fault protection

  http://en.Wikipedia.org/wiki/crowbar _ (circuit)

  Here are the instructions to deal with this series of beeps of a previous HP xw technical and repair.  Note the number 2 in the troubleshooting instructions... usually you don't have to go down to 3, in my experience.  I think that you have already found the faulty unit:

  Loss of power.
  1. open the access panel and make sure that the power cable is properly
  connected to the system board.
  2. Locate the faulty device by removing all devices and then reinstalling one at a time
  until the workstation fails. Replace the device at the origin of the failure. Continue to add
  devices to make sure that everything works correctly.
  3. check the power supply feature.
  a. turn off the AC power.
  b. remove all cables internal power on the system board.
  c. connect the power supply.
  ● If the power supply fan turns and the BIST LED lights, then the
  power supply is good. Replace the motherboard.
  ● If the power supply fan does not turn or the BIST LED does not
  light up, replace the power supply.

• I have printer color laserjet 5550N having problem with error 59.C0. What is the cause of the error?

  I have printer color laserjet 5550N having problem with error 59.C0. What is the cause of the error?

  Thanks Ray,

  Hello... How can I get the manual download for all the error on any printer laser color spray top of HP range.

  Kind regards

  Monday Nwankwo

• New problems to update with lower opacity effect

  Since the new update of Adobe Muse in February, I noticed that the text lower opacity on my pages do not work when I'm writing the site.

  Website: http://www.ampaevents.com/wed/about-us.html

  For example, the dreams of design should be transparent.

  I took the PNG of your page and placed it with opacity reduced on the other elements of a provision of the Muse. Everything worked well.

  Could you reduce as much as possible a single page, upload it to a provider of cloud like dropbox and post the link here?

• Application loader stuck on "authentication with the iTunes store."

  I'm trying to submit my app via iTunes Connect. I was stuck on "authentication with the iTunes store" for more almost 20 min. Is this normal? Something wrong?

  

  I followed the Guide step by step Adobe publishing applications iPad and everything went smoothly thanks to the DPS App Builder. I was able to download both the app developer .ipa and distribution app .zip following the steps very well. But eventually, all measures are useless: interface of iTunes Connect has changed since the guide Adobe did, and now I'm completely lost.

  I downloaded the app Loader and try to submit this .zip app developer I have to iTunes Connect via the Application Loader. But in vain.

  Any help would be really appreciated. Thank you

  You can ignore this warning. You will, however, probably to encounter other errors. Please see http://status.adobedps.com/ for later.

  Neil

• Change the color of Clip from movie with the external Variable

  I have a movieclip in my flash file (WhiteBarMC) I want to be able to change the colors on the use of a variable (hexadecimal number) assigned from an external file. I found a script that comes close to what I want to achieve, but I don't know how to run the changes I need to make it work.
  
  on {(overview)
  var colorful = new color ("_root. WhiteBarMC");
  colorful.setRGB (0 x 006699);
  }
  
  It is narrow because it changes my object/Movie Clip on roll. BUT I have two problems...
  
  1) I want to set the hexadecimal color code in an external file as a flash variable retrieves and then applies to this movieclip. If it helps to explain why, it's because I have multiple variants of this swf throughout my site with a different text that just overlap the coloured bar movieclip (i.e. galleries, contacts, subject, etc.) So, with a change in an external file, I have the ability to change the color bars in the world to match the changing colors on the site.
  
  I created an external file ".txt" with only "myColor var = CC0033" in the file. I don't know if it's right, or even the wrong way, but I thought it help those smarter about what I'm doing.
  
  (2) I don't want my viewers having to "roll" to activate the change. I want it to happen during loading.
  
  
  Anyone who can help is a hero. Don't forget, I'm not this control to the action script, so a little guidance and clarity in your response will allow immensley! I owe you a dinner!

  Place this code on the root timeline containing your video:

  my_lv = new LoadVars();
  my_lv. OnLoad = function (s) {}
  If (s) {}
  var colorful = new color (_root. WhiteBarMC);
  colorful.setRGB (this.myColor);
  } else {}
  trace ("failed to load the file");
  }
  }
  my_lv. Load ("Colors.txt");

  Where colors.txt is a file with: & myColor = 0xCC0033 & (as kglad said)

• HP 5940 - color cartridge status light flashes with new HP 97 cartridge

  Just installed a new HP 97 cartridge and the light flashing color cartridge status. Put in old 95 HP cartridge and the lights are out, but this cartridge is empty. I have cleaned all connectors (inside the printer and the cartridge), tried reinstalling several times. Any ideas or am I stuck with a bad cartridge? The only difference I see between the cartridges, it is that the 97 is a greater variation of the 95. Thanks for any help.

  Never forget, faulty cartridge. He took over and replaced it, it works now.

• How youprint a test page, I get only colors Blue/gray without red or yellow

  new printer and ink, but do not print red or yellow

  You can print a test page from Windows from printers and faxes, right click on your printer icon, selecting Properties.  There is a 'Print Page of Test' button under the general tab of the Properties dialog box.

  Many printers can also generate a test page for their controls on the front panel.  Read the User Guide.

  In general, the failure to print certain colors means that something is wrong with the print head or ink cartridge (depending on the printer).  Refer to troubleshooting in the user's Guide for your printer.

  If you can't resolve it with the suggestions in the Guide, and this is a new printer, I would take it back.

• USED ALL THE NEW INK COLOR COMES OUT MOSTLY RED

  Printer: HP Officejet Pro 8500 has o/s Win 7-32 bit

  With the help of new cartridges but the color comes out with too much RED

  The 8500 has uses a printing mechanism where the ink cartridges are installed in the front left side of the printer and the print heads are internal.  The ink is channeled from the print cartridges for the in-house print heads.  With this printer, a question as it is usually an indication of a spurious print head.

  I would recommend printing a report of quality Print the Configuration menu > tools on the control panel of the printer.  This will help to give a better idea, if the problem is hardware (printhead) associated with the printer, or a problem of software with the driver on the PC.

  There is also a document to help solve print quality problems in the Officejet 8500 A910 a.  The document can be accessed here.

  Let me know how it goes.