Communication series with Mettler Toledo 205 XS

Similar Questions

• Interfacing with Mettler Toledo IND560

  Hey everybody,

  I'm trying to get a scale (Mettler Toledo IND560) to work with a VI I have already created. It is connected by a serial connection 9 pins which is managed via a conversion Series / USB.

  It gives me a little trouble, and all I found through research is a pilot to balance work with a server of the OLC. I personally don't have access to one, and I was wondering if there is a simple step that I'm just missing.

  Thanks in advance!

  I think that you may need to be more specific.  Exactly how long do you have?  And exactly where are you stuck?

  The first thing you will need is the manual for the device.  Reading in place on their suggestions to communicate with the device.  They must specify the parameters of connection (for example, baud rate, etc).  And they could describe a specific high level protocol, you need to follow to get the data.

  And then to start with LabVIEW and serial communication, you will need to make sure that you have installed NI-VISA.  Then use built-in LabVIEW example Finder.  Take a look at this VI to go:

  Material input and output > series > basic writing and reading series

• LabVIEW with Mettler Toledo Balance through. Help!

  I design a VI that will take a measure of weight and this chart. I thought of her so that I have a stop button and a chart. What I need now is a zero and Tare button. It would be nice to get the correct format on how to use this range of Mettler Toledo device so any info would be great.

  Later on the road, I would like to add a timestamp to every second and a test for each identification number.

  I've tried everything! Help, please. I'm new to LabView and would hear all the advice I can get.

  Thank you

  Mike

  You should learn how to use case commands exhibition.  See below.

  

• communication series with VISA

  I'm trying to communcate with a power supply via a serial connection.  Communication works very well in Hyperterminal and putty, but I can't seem to run in labview.  It times out when trying to read the data.

  Hyperterminal parameters are the basis of everything and it works fine

  9600 baud

  8 data bits

  no parity

  1 stop bit

  no flow control

  Send "VOLT?" with CTRL + J for line break

  Returns under the voltage at the output of the UUT.

  I wonder if I send you the incorrect order in labview.  Any help would be great.  I have attached the VI, it's my first try at comms series so it's pretty baisc and I do not know I'm missing something

  You are not sending the line break.  You send only "Volt"?

  Make a right click on the string constant, visible display style and make \codes show.  Then enter \n at the end.  Now you send VOLT? with the line break.

  In addition, remove the shift regsiters on the son of reference and error.  (A single time-out error will keep your VI to run again until you stop and restart the VI)

  And put a close VISA outside the loop.

  

• Communication series with ANSI emulation

  I have a mass flow of gripper controller that uses a connection set to read/write.  I have the connection works in hyperterminal, but we are updating our computers and do not use more serial ports.  I have a cable USb232 and now trying to establish the connection through labview.  There are several required specific hyperterminal settings to get the device to communicate that I can't find in the settings of labview.  The device requires:

  1. 19200 bauds, 8 bits, no parity, no flow control (not a problem, can adjust these settings)

  2 terminal emulation must be set to ANSI

  3. under the ASCII Configuration

  Send line with line breaks ends is NOT enabled

  The echo typed local characters is turned on

  Add RSS to finish lines is running

  When I connect through the serial.vi base, I get a time-out error and do not have all the data of the device.  In hyperterminal, the news on the device are questioned by sending 'A' to the device.  Any help for this communication device would be appreciated.

  Thank you

  Problem solved, I just to activate the writing of the end and read with characters of endpoint and the hexadecimal value on D.

• Communication series with visa, need help

  IM G-codes(which is a string in this case) sending to my Board of Directors, Im using the structure of the event choose sent a code that, when sending as string constants program runs without problems, but when Im getting the format string to string program dosnt sent the code in this case, but its present when events change (so in other cases it works too previous)

  problem can be seen in the performance of climax too

  I will ask once again: do you need to send a character of endpoint with your order?

  Your 4 character button events 'home' have all orders ending in the line.  Other events are not.  My guess is that the unit does not recoginize newline character he received a valid full command until he got the line.

  PS: Those who touch terminals that belong in their boxes of the discipline concerned.

• Communication series with Miteq switching system

  Hello

  I am trying to contact a Miteq redundant switching system 1:8 for high power amplifier.

  My VI gives me an error of framing. I have already read the thread on the mistake of framing posted here and made sure my port is configured to match the settings of the device.

  (Data bits - 7; Parity - same, baud rate (9600) equipment is silent about data flow and the stop bits, (I guess NONE and 1.0 respectively)

  I use a laptop with a USB port. I have a USB-serial cable of NOR. I use an IC -? 855 RS232-RS485 converter because the system is RS485. I already checked the pinout for the port that I use a fact a connector corresponding Tx + in the converter with Rx +; TX - Rx-; and the other two wires are connected as well.

  I opened MAX and tried to write directly to the VISA driver, but I get an error as well.

  I do not know if the manual is just, he is a former switch and someone could have changed the port connections.

  Y at - it a trick to know what is the link?

  I'd appreciate any thoughts here

  Thank you very much

  Hi Jeff,

  I can't open the link you sent, but we finally thought that the problem is the connection of broaching. Me not according to the manual or any document we have.

  Sorry I did not before.

  Thank you very much for answering!

• Writing of multiple orders with communication series

  Hello

  I'm quite familiar with the basics of LabVIEW, but I'm new to communication series with VISA. I had no chance of finding a solution to my problem, but it is similar: http://forums.ni.com/t5/LabVIEW/VISA-read-write-to-serial-port-Unable-to-impelement-multiple/td-p/93....

  I am able to send a command and read the response with the device, but I can't send several commands to change the settings of the device. For example, I send 'F' to the device to read the current operating frequency and read the response (22). But if I send 'f' to the device to change the operating frequency, read the answer ('send frequency... (''), then send my desired frequency (120), I get no response.

  The default frequency at the opening of the port of the unit is 22. I would like to change the frequency to 120, then read the current operating frequency to ensure that it was indeed changed.

  I'm confused about the format of data to be sent in LabVIEW. In MatLab, it works fine if I send 'f' as a character (fwrite), followed by the desired integer frequency. However, in LabVIEW, it seems that the number I want to send is not read correctly. I have tried to cast the integer to a string and read that the slash code, hexadecimal, normal code, all I could think about.

  Help, please

  This give a try. Press the button "Prepare", followed by the 'Set Freq' button. You need to configure your serial port properly first well.

• Communication series

  Hello

  I'm using communications series VISA in my vi to communicate with the hardware. My laptop has two COM COM1 and COM2 ports. I'll be using VISA configure a serial port to set specific Com Port.

  COM port will be indicated by using the name of resource VISA. I should know the status of com before another operation takes place. IE say I chose com2 on behalf of the resource for the COM port configuration, but I connected the hardware serial cable on COM1. How can I know the difference? I tried the line of the error checking, but unfortunately his does give no error since the COM1 is present in the laptop.

  Thanking you,

  sushmith

  Hello

  The idea would be to write * IDN? (or you can select the order based on the expected answer your device connected to COM port) command individually, to the COM port

  This should return the identification of the unit (or a known response) of the device connected to the COM port when trying to read the data for the number of available bytes to the port.

  If the returned string is empty (or not the expected answer) then that would mean that no device is connected to the COM port.

• Communication problem with the printer

  I'm trying to print on a printer Lexmark 1200 series of a Toshiba laptop. Laptop computer identifies the printer is the printer is displayed in the control panel. Whenever I try to print even if I get a message that says: "communication problem with the printer. Any help is appreciated.

  Hi Nick,

  1. What is the exact model of the printer number?

  2 is this problem limited to any specific application such as Internet Explorer, Microsoft Word etc.?

  It seems that some of the 1200 Series printers is not compatible with Windows 7. You can enter the number of exact model and research for more information.

  http://www.microsoft.com/en-us/windows/compatibility/win7/CompatCenter/ProductViewerWithDefaultFilters?TempOsid=win7&Locale=en-us&TextSearch=lexmark%2B1200%2B&Type=Both&CurrentPage=0&TotalPages=1&ShowCriteria=0&SortCriteria=Relevance&Compatibility=Unknown&LastRequested=14

  If the printer is compatible and you are always faced with the question, you can proceed with the steps.

  Method 1:

  Run the troubleshooter and update printer drivers.

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Method 2:

  If the problem persists. I suggest you perform the steps described in the article.

  "Communication not available" or "Document Failed to Print" Error Message and the print job hangs in the print queue

  http://support.Lexmark.com/index?page=content&ID=SO4473&locale=en&UserLocale=en_US

  Note: Antivirus software can help protect your computer against viruses and other security threats. Have a computer without any security software can cause a potential danger to your computer. Therefore, make sure to activate the firewall and security software once you are finished with the test.

  Hope this information helps. Response with status so that we can help you.

• Management communication series through liaison camera card

  I have a card OR cameralink and want to handle the integration of a camera time using the controls of the camera series.  Is it possible to place orders of series using other software like MatLab (heresy I know)...

  My experience using MATLAB is absent, but if you can call the C API for IMAQ, then you should be able to do.  You can take a look at the help of the reference of the NOR-IMAQ function and specifically examine the functions of Communication series under features low level.

• That engine run time is necessary for communication series build Setup

  That engine run time is necessary for communication series build Setup

  You need NI-VISA. If you are using a National Instruments serial port card or device, then you also need OR Serial. All software can be found in the Technical Support page.

  Obviously, you have also the runtime for the software development environment itself as well. For example, for LabVIEW, you need to the LabVIEW Run-Time.

• On the Sync Palm m500 using connection series with a dock under Windows 7

  Palm: m500

  Link: Serial (cradle)

  OS: Windows 7

  Problem: Palm Desktop 4.1.4 cannot be installed and does not synchronize Palm Desktop 6 using the serial connection.

  How can I synchronize the m500 using connection series with a version of PD under Windows 7?

  Nevermind, helped http://forum.brighthand.com/sync-windows-palm-os/261651-synching-legacy-pim-databases-palm-desktop-v-6-2-a.html .

• Driver tools - Mettler Toledo

  Hello

  ICH möchte eine Mettler Toledo Waage Typ AB204-S/fact mit LabView ansteuern uber RS232. Lt. Mettler Toledo function alle Waagen uber six instructions. Leider ist meine Waage bei den Drivern Instrument nicht aufgefuhrt. Weiss someone, ob auch sharp mit dem Treiber works/function would? ICH habe are already versucht, aber leider erfolglos (mit diesem: http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=0472641F8294078BE0440003BA7CCD...)

  Vielen Dank für die Hilfe.

  Hello

  Do you have to doublecheck your serial line?

  It's a straight or crossover cable?

  the handshake is correct?

  This is probably the way to check and balance in the right mode to be read by a pc?

  I groped almost one day a few years before it really worked.

• Get "communication error with kernel" message when you try to run a virus scan program

  Get "communication error with kernel" message when you try to run a virus scan program

  Hello

  What antivirus do you use?

  Follow the steps in the article mentioned below and check if this solves the problem.

  
  The error message "error communicating with kernel":
  http://KB.eset.com/esetkb/index?page=content&ID=SOLN2280