Composition B2B Expressway Cisco tests

Similar Questions

• RMS Expressway Cisco licenses for B2B calls

  Hi Experts,

  We have Cisco Expressway Setup for B2B calls. We have 6 licenses RMS across Highway C & E, making 3 on EXP E and 3 on EXP C.

  Now, I'm able to do 3 Conference of the party including the host. Myself and 2 other B2B calls for a video conference. Where that we watched for 3 with the exception of the host Party Conference.

  We were under the impression that if we buy 3 licenses RMS, we have 4 video party conference. It's 3 outside calls excluding the host.

  Can someone explain how the RMS license.

  Our IPT put in place:

  CUCM 10.5

  SX20 - recorded at CUCM

  Motorway C - containing 3 licenses RMS

  Highway E - containing 3 licenses RMS

  Concerning

  Benyoucef

  Hi, Renaud,.

  Licenses RMS are concurrent, so in your case both licenses RMS (one in each Expressway) per call are necessary. You can check the following positions related to similar queries

  https://supportforums.Cisco.com/discussion/12444331/Jabber-guest-require...

  https://supportforums.Cisco.com/discussion/12522961/RMS-license-Cisco-ex...

  https://supportforums.Cisco.com/discussion/12240916/Expressway-LIC-exp-r...

  Manish

  -Does the rate of useful messages-

• Issue of Cisco Expressway MRA

  Dear all

  I'm testing the MRA of VCS - C and VCS-E feature

  I use the firewall architecture 3 ports that the VCS - C and CUCM are placed inside with the same subnet.

  The VCS-E is placed in the DMZ and static use of the ASA 5510 1-1 NAT to translate private IP address: 172.16.0.225 to the public IP address, for example 100.1.1.1

  In the context of VCS - C, I use the FQDN of the SCV - F that map to the public IP of VCS-E (100.1.1.1)

  And the VCS-E use the FQDN of the SCV - C to map to the IP private of VCS - C

  Area traversed in VCS - C is active, but the area crossed in VCS - E is inactive, it is said that server inaccessible.

  I found that my VCS-E is not the license of the Advanced Networking option.

  In the VCS-E ip settings page, there is not any NAT setting

  I want to ask if I need to use NAT, in addition to the NAT of firewall functionality, I need also the license of advanced networking option to activate NAT in VCS - E?

  Or it may work to use only the function NAT firewall without NAT for the VCS - F?

  Also, I put the reflection of the NAT to my ASA 5510

  Hello

  The option networking advanced to activate NAT on VCS - E or the edge of the highway is a requirement for the crossing of firewall deployment.

  Useful guide:

  Deployment Configuration Guide (Control with Expressway) Cisco VCS Basic (X8.7)

  With your case about the progress of the deployments of networks, you will need to follow the 3 firewall ports using single VCS Expressway LAN Interface DMZ on the guide on page 60.

  Kind regards

  Acevirgil

• Cannot test the Composite SOA

  Hello

  I'm new to SOA and when I deploy a composite, I'm unable to test the composite. As the test of the EM Console button is disable. It's a simple project with an FYI the task and start and end of activity.

  
  

  How does your process starts or what triggers the composite soa?

• Cisco DX80 Microphone Skype for business

  Hello

  I am facing a problem with a Cisco DX80 model. The device is registered to a CUCM.

  The problem is the microphone when you use Skype for business. Please see the attached picture.

  In the settings for the Skype for business, I can choose the DX80 as speaker and ringtone, but there is no entry for the DX80 microphone like the one for the laptop itself. Like the screen DX80 is also used as control for the laptop off course gives a poor sound quality to the listener. Now, I would like to have the Skype to use the construction of microphones in to the DX80. But it seems not to be possible. We use THIS software for the endpoints DX80.
  I tried to make calls using the DX80 as videoconferencing unit to another system of videoconf Cisco test and here we have no problem with the microphone / sound of the system.
  Of course, the problem is that the microphone can not be chosen in the settings of the Skype for business. I guess it must be possible?

  Best regards
  Brian

  When you have a laptop connected to the DX80 or any end point of telepresence, you can use it as an additional monitor and speaker, the microphone is not connected, and cannot be used with the computer.

• Disable the TEST button in the console SOA 11 g Em

  Hi all
  
  I am using SOA 11 g (11.1.1.3 version). I have deployed some composites and wanted to test them. But in the em console web service test button is disabled. I don't see an option to test the web service when I right click on the composite.
  
  All the world is facing this problem. What I have to do all the new configurations. Note that it is a new 11g soa environment.
  
  
  Thanks in advance

  you have exposed a (soap) service in your composite? (dragging a component from the middle lane to the left lane swimming swimming)

• B2B-101 - Custom_1.0_orders_generic_file application not working properly

  Hello
  
  
  I followed all the steps to build the sample b2b-101 - Custom_1.0_orders_generic_file for a custom protocol.
  
  I have configured the channel for receiving trading partner globalchips as c:\globachips as I have configured the channel listening to the host partner Acme c:\AcmeListening Channel commercial.
  
  I have deployed the composite b2b-101-custom_file_inbound_application and b2b-101-custom_outbound-application.
  
  But when I try to send the message using the composite output (i.e. the file read machine using the file adapter and send the message to b2b using adapter b2b trading partner: Acme and trading partner: globalchips) of Acme at globalchips the duly filled in reports, but the composite deployed watch message is not looking for B2B message.
  But when I put the GlobalChips_123.dat file in the channel listening to Acme, the file is processed and the message appears filled in reports. Also composite entering picks up this message and writes the file to the local computer.
  
  So is it that the composite entering only retrieves the message send receving trading partner not partner commercial host?
  
  
  Can someone please help me to debug it.
  
  Thanks in advance
  Jonathan
  
  Published by: Jonathan on January 11, 2011 22:30

  Hello Jonathan.

  Log shows clearly that the remote endpoint TP channel is C:\\INDU\UMANG\B2B\INPUT-

  [2011-01-12 T 14: 34:41.186 + 05:30] [soa_server1] [TRACE] [] [oracle.soa.b2b.engine] [tid: weblogic.work.j2ee.J2EEWorkManager$WorkWithListener@1af4fbd] [username: ] [ecid: 0000IptU43f5i ^ R8mZ0Vtn1DBKSv0001hA, 0] [SRC_CLASS: oracle.tip.b2b.system.DiagnosticService] [APP: soa-infra] [decided: f53f2be3008c681a:18f7492:12d78df7167: - 7ffd - 00000000000032f4] [SRC_METHOD: synchedLog_J] oracle.tip.b2b.transport.TransportInterface:send URL: FILE://LOCALHOST/C:\\INDU\UMANG\B2B\INPUT

  Acutally the path of channel tp is c:\indu\Umang\B2B\GlobalChips

  I don't know where you see point endpoint c:\indu\Umang\B2B\GlobalChips but the mentions of B2B newspaper that deployed agreement no TP as C:\\INDU\UMANG\B2B\INPUT channel endpoint

  Double-check your agreement and your remote TP configuration. Send me the export agreement if you are still not able to find endpoint

  Kind regards
  Anuj

• public or private vcs-e dns?

  in my current setup my vcs-e uses local dns server, but I read there a public need, even if currently jabber works very well without any problem and mcu conferences work ok, my questions is do the need of vcs-e a public dns? and why? It would explain why I can't make calls outside my network when my video units are stored in the vcs - c?

  For PT. 1 & 2, you establish a B2B call to the external endpoints.

  # 3: Jabber Cisco will use a different area, which is the crossing area and if you say that it works if the area is in place.

  You have a DNS Zone configured on your VCS-E?

  DNS zone is used to find systems that are hosted on the outside (which are not locally, for example, a company). Destination alias are sought by a name using a DNS lookup.

  # 4: After creating a DNS on VCS - E Zone, you must create a search rule that will target your DNS Zone. See the configuration guide on and go through the task of 11 to 13 on p. 24-28.

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/VCs/config_guide/x8-7/Cisco-VCs-basic-configuration-control-with-Expressway-deployment-guide-x8-7.PDF

  For #5. For SIP using B2B calls, see VCS for Cisco IP using the Port for Firewall Traversal Deployment Guide on pages 8-11 for a list of ports.

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/VCs/config_guide/x8-7/Cisco-VCs-IP-port-usage-for-firewall-traversal-deployment-guide-x8-7.PDF

  Also try to test call B2B with this test site:

  [email protected] / * /.

  This tool also allows you to check the records of services/SRV SIP for successful B2B calls. You can check the SIP endpoint domain name you call and your video network SIP domain name if these entries have been found: https://cway.cisco.com/tools/SrvRecord/

  • _sip._udp. Domain
  • _sip._tcp. Domain

  Kind regards

  Acevirgil

• Need for a coefficient of fish using deformation measurement gage (wheatstone)

  Hello

  I'm building this interface labview eventualy do strain meter measures on composite samples. I tested what I've done so far in half-bridge config. and so far so good. I read about the need for my wages on the material in half or full-bridge ( http://www.ni.com/white-paper/4172/en/#toc1 ). My question:

  LabVIEW should a ratio value (s) accurate material fish when you use DAQmx (one of the "Measurer of strain information" requested as input for DAQmx) to get good accurate values of strain?

  (1) in other words, if I use 2 measurers (half-bridge: one in the axial direction of the sample, one at 90 ° from the axial direction on the sample), Labview DAQmx will not use the "ends of balance (accuracy/temperature/offset) of the half/full-wheatstone-bridge-config with only a. relevant fish worth?

  (2) If Yes: This means that I must first find coefficient of fish of the material for each type of material (composite). So, what would be the best way to put my wages (half of the full bridge) on the material to know an "accurate experimental value" coefficient of fish without having? (looks like using bending modes are the only way)

  (please consider http://www.ni.com/white-paper/4172/en/#toc1 as a reference)

  TY,

  Daniel

  Strain_Life,

  From what I could dig up, LabVIEW will not calculate a coefficient of specific real fish since it is purely an entry and uses only this entry for v.f..  Half and full bridge configurations are only for the "purposes of balance." This limits you to calulating your own fish for the composite ratio, which, at best, would be a way of the materials that you use.  This is a pretty good site for known values of the coefficients of fish from: http://www.engineeringtoolbox.com/poissons-ratio-d_1224.html

• Unity 4.0 (2) and /ForestPrep for Exchange 2003

  We plan to upgrade our Active Directory in Windows Server 2000 and Exchange 2000 to Exchange 2003 and Windows Server 2003 AD network. We currently have two unit 4.0 (2) servers (Unified Messaging) in two separate locations, each serving a different group of offices. All in all, we have more than 1,000 users in 5 different locations. All these users and locations upgrade to Windows 2003, Exchange 2003 and unity 4.0 (4) at the same time is not an option. Therefore, we would gradually migrate each location to Exchange 2003, Windows 2003 and unity 4.0 (4).

  I understand that unity 4.0 (4) is the recommended version to use with Windows 2003 and Exchange 2003, but I've also read in Cisco documentation as 4.0 (4) unit when running on Windows 2003 requires that you are already running Exchange 2003. What confronts a dilemma in that we have separate locations of mutiple supported by one server shared unity and we simply cannot risk all these sites simultaneously to unity 4.0 upgrade (4), Server 2003, and Exchange 2003. So, what would be the best strategy to go where we want to be? This brings me to the following questions:

  a. If we run / Exchange 2003 ForestPrep against our field now even if we are always unity 4.0 (2)?

  b. can we begin to introduce Exchange 2003 servers in each of our branches (administrative groups & routing Exchange) while staying at unity 4.0 (2) provided that these servers are not designated as a partner of unity and without voice mail server or connectors of the unit (for example, unity voice bridge connector) are on these servers?

  c. would make sense to upgrade the servers of the 4.0 unit (3) first and then move to unity 4.0 (4) once all the Exchange servers in all our branches have been improved in Server 2003 and Exchange 2003? This interim update seems to give us more flexibility in our path to upgrade its operating system to Microsoft Exchange server version requirements are less onerous

  Windows 2003 is not necessary for the 4.0 unit (4). Likewise, it is not recommended because there is evidence of the way in which Windows 2000 with the unit, but we do support Windows 2003 if the client really wants to use it. We ship the unit on Windows 2000 and that's what we recommend at this time. No functionality is lost under Windows 2000.

  Officially we do not support have all Exchange 2003 servers or even execution of ForestPrep if you have lower than 4.0 (3). That said, the only flaw we've never seen this is when the unit is connected under the local system or when the subscriber accounts are on Exchange 2003 servers. You wouldn't be the first customer to do so and it should be fine but really understand that it is not technically a Cisco tested and taken in charge of the configuration.

  Thank you

  Keith

• Replaced VCS

  Are VCS replaced totally by CUCM? Could someone please give a link documentation on how VCS complish on CUCM features? Thank you.

  "Venture capital" has not been completely replaced by CUCM... so that you can now register directly SIP endpoints in a call rather than VCS Manager, a VCS will still be required for some of the endpoints older existing.

  The VCS-control and VCS Expressway are always kind to present in a CUCM world - now called the Series Expressway Cisco.  They do have the same basic with a different license software.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Motorway E overlap in srv records

  Hello

  In a design of the Express way, using a cluster of Highway MRA for registration and another cluster for B2B call (and jabberGuest).
  We use the domain name "example.com".
  This means that clients jabber and video endpoint use the URI as [email protected] / * / your registration through cluster MRA.
  If outside the appeals of a jabber client or a videoendpoint on the "example.com" domain call must pass through the pole B2B.
  Question:
  The sips 5061 SRV records must be made on the domain 'example.com' but where it should point the MRA cluster or Cluster B2B?

  Henry

  For ARM, you only need the SRV tip collab.  According to the Expressway Administrator's guide, it is said of SIP SRV record is not necessary for mobile and remove access.  The SIP SRV should point to your cluster B2B Expressway, for incoming calls.

• Cannot uncheck a footer on some points

  Hi, so there are three .png images on all pages of my Web site and all are marked as footer and I can not uncheck for a reason any (the icon in the upper right and the option to footer in the menu 'Object' are inaccessible). I'm on a macbook with Muse CC 2015. Someone please help, I don't want to have to redo the ENTIRE site again. Thank you thank you thank you

  

  It seems that the images are inside a widget (State button) or Composition? I just tested it. If image frame has been defined as a footer element, before it was moved to widget, it retains its status as a footer, but it will be gray, even if the widget containing is not defined as part of the footer itself. Drag the image out of the container of the widget, you should be able clear the footer selector. You can then place it in the widget.

  David

  Creative muse

• I have a viewer with a link button problem with vimeo

  I have a viewer with a vimeo link, so when the video plays the darkened background. The problem Im having is the button to launch the video is just Gray, I can't change it. I want her to be in the form of a graph not a thumbnail of the video if possible

  This isn't the Image that creates the gray line. Its the fill color of the relaxation.

  If you created it with LightBox view Composition so the following test

  1. Select the trigger in question

  2. Select None in the fill in the toolbar such as mentioned in the screesnshot below

  3. make sure to do this for all States of relaxation. Particularly active state.

  

  Let me know if you have it created with the help of the jQuery slideshow.

  Kind regards

  Vivek

• Style of text that can be changed to auto-update of any instance of this class in the same project EA.

  In programs like Dreamweaver and Muse, we have a range of properties/tool to define and styles of text and stored to be reused and editable - so if you say change all the titles under the project in a different typeface, color, size etc. you can just change the settings in the css Panel (or equivalent). How do you do that on board? It must be possible, right?
  
  I use Edge animate 2015.
  
  Thanks, Shaun
  
  

  Hello

  You get by using code. You can browse your composition.

  Code tested with edge 6.0.0

  SYM.$("p") ==> returns paragraphs. If a collection.

  SYM.$("p"). each () ==> browse each item.

  SYM.$("p"). each (function(index,item) {}

  Console.log (sym. $(item). ) CSS('font-family')) ==> returns the family of police for each item

  } )

  Therefore, you can create a conditional statement.

  SYM.$("p"). each (function(index,item) {}

  If (sym. $(item). ) CSS('font-family') == "sought fonts") {sym. $(item). } {CSS({... new font...})} ;

  } )

  Note: jQuery is not necessary.