computer does not CONNECT to c4480 after move from DSL to cable

Similar Questions

• I just installed a new router and now my desktop running Windows XP computer does not connect to the internet.

  Hello

  I just installed a new router and now my desktop running xp computer does not connect to the internet. I know that it is not the router because I plugged the cable into my laptop running 7 and it works fine. When I try to dhcp I get 169..., when I put manually the IP just get no access to the internet and can not ping to the router address. I tried to run the net work Assistant, emptied my dns, disabled all firewals, still nothing.
  Any suggestions?
  original title: connectivity Limeted

  The zero configuration utility works very well. But it is a desktop computer and on cable. All other wired and wireless PC in the office is working well, then it's definitely this PC. He came out of nowhere, I install a network printer on the PC but that's all.

  Your messages are a bit terse, but if I understand correctly

  • You have a router connected to the Internet and multiple computers connected to the router, some Ethernet cable and others by wireless.
  • All but one of these computers can reach successfully from the Internet via the router.
  • A computer that can't browse the Internet is connected to the router via an Ethernet cable.
  • You disconnected the cable between the router and the desktop problem and connected it to a Windows 7 laptop and the laptop connected to the Internet via the router.
  • You haven't seen any error message (except, perhaps, a message on "Limited or no connectivity").
  • You have installed Windows XP Service Pack 3 (or at least Service Pack 2)

  Assuming that all the foregoing is an accurate summary of the situation, I suggest that you do the following:

  Open a command prompt window (start > run > cmd > OK)
  Type the following lines and press ENTER after each line

  Netsh reset winsock catalog
  netsh int ip reset c:\resetlog.txt

  Close the command prompt window and restart the computer.

• Computer does not recognize the monitor after update of Win7.

  Computer does not recognize the monitor after update of Win7. Have a projector connected to the computer with the monitor; from clogging the last evening updates have been installed. When the computer has been restarted this morning the monitor is entered but did not detect a signal and fell asleep: do not get an image on the monitor or projector.  Suggestions?

  It is a laptop?

  And if you start in safe mode?

  Desktop

  Haven't tried safe mode
  Disconnected the projector, and then restarted; back to work now!

• I worked on the Web site of our Church and all of a sudden my computer does not connect to the site. I get a message saying that the connection to the server was reset while the page is loading. Can anyone has any ideas on how I fix?

  I worked on the Web site of our Church and all of a sudden this week, my computer does not connect to the site. I get a message saying that the connection to the server was reset while the page is loading. Can anyone has any ideas on how I fix?

  The error message "the connection was reset" can be caused by a bug for the attack of the BEAST fix (browser exploit against SSL/TLS) that the server does not support.

  • [918127/questions/918127]
  • [918028/questions/918028]

• Apparently, I got an automatic update of Windows XP. All of a sudden my computer does not connect to my HP Laserjet 1000 printer.

  All of a sudden my computer does not connect to my HP Laserjet 1000 printer. These work very well together for several years.

  Now all of a sudden I get a message that the computer cable is not connected.  I tried to charge the printer program.

  I unplugged and reconnect the cable to the computer, etc.. The system does not work.

  I learn by two other people, who have automatic updates of Windows, they had the same problem. We have a Kodak

  printer and the other has a Lexmark printer. This makes me think that the problem is in the updates of Windows.

  So, what should I do to fix this? I'm NOT a computer person and I'm confused.

  James

  Hello

  · The updates have been installed on the computer?

  You can follow the procedure from the following link: printers HP LaserJet - USB Devices closing work unexpectedly in Windows XP: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=45674&prodTypeId=18972&prodSeriesId=45674&objectID=bpl11421

  You can also access: family of products HP LaserJet 1000 - Error Messages on the computer (PC): http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=240170&prodTypeId=18972&objectID=bpl11045

• I've updated windows and now my computer does not connect to the wireless network.

  I've updated windows security updates and now my computer does not connect to the wireless network.  Until then, it worked very well and even now it will connect through wired connection but not wireless.

  Hello
   
  You can follow below link that can help you to solve your problem:
  How to troubleshoot wireless network connections in Windows XP Service Pack 2
  http://support.Microsoft.com/kb/870702

• My computer does not connect to the wireless network

  My computer does not connect to a wireless network. It's almost like there is no WiFi. I go into the settings and nothing is. I know that the networks are there because the other computers connect to it. He says always "no connection available. When I try to pull of boredom he tells me to plug an Ethernet cable, which is the thing that I try to avoid. I want to connect to WiFi.

  Based on this information, your laptop isn't wifi, it is turned off, or it is broken.  A wifi used to work?  If so, what happened to your system, just as the problem started?

  Type "Device Manager" in the search box and press ENTER.

  • Look in the Device Manager to the network adapter section.
  • What devices are listed?
  • Are there warning icons?
  • It appears to be a wireless adapter, what's his name? Double-click it and to report to what is shown for "State of the device.

  You can also provide additional diagnostic information:

  • Type 'Information system' in the search box and press ENTER.
  • Click in the system information window and select all (CTRL + A) and copy (CTRL + C)
  • Paste (CTRL + V) the data in your response here
  • Return to system information window and click on the + next to "Components", then click on the + next to "Network", then click on 'map '.
  • Select all (CTRL + A) and then copy (CTRL + C)
  • Paste (CTRL + V) the data in your answer below, other data Information System

• OfficeJet 7410xi: computer does not have USB printer after upgrade to window 10

  The computer does not find the USB connected printer (Officejet 7410xi) after having modernized the window system 10.

  Hello

  Download and install the following software:

  http://ftp.HP.com/pub/softlib/software13/COL30951/MP-110165-3/AIO_CDB_Net_Full_Win_WW_140_408-5.exe

  During SOUTH clck the link (4th one) software selection step and uncheck the Bing toolbar due to incompatibility issues with MS Edge, then continue with the installation of you

  Please let me know the results,

  Shlomi

• Computer does not recognize router befsr41 after that I tried to reset it.

  So earlier today, I tried to reset my router because for some reason that I could not log in with my password I use normally, after switching to AT & T of the Charter (from DSL cable)

  Just after that, we moved the router does not either, but we called linksys for repair, but we had to pay $30 and I'd rather not do it again.

  Anyway, my computer will not completely recognize my router. I can't access it is based on the web options page, if I try to use the CD it will say that my computer is not connected. I know the cables are connected correctly.

  Oh and also, why I couldn't use my old password?

  Someone at - it an idea on what could be wrong?

  As you have activated your ISP to a cable on the DSL. The first thing you need to do is, pick up your Modem to the router. Let your Modem is connected to your computer. Press and hold the button of reset for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  Once you connect to the Setup page of your router, on the Configuration tab, you need to change the local IP address to 192.168.2.1 and click on save settings.

  Once the settings are successful, unplug the power from your router and Modem. Connect the Ethernet cable from your Modem to the Internet Port Linksys router. Connect the power to your Modem first, wait until all lights are cover, connect the power supply to the Linksys router. Once all the lights are solid check if you are able to browse the Internet on your computer.

• My computer does not connect to my network... !!!

  Hi, my Dell laptop (Inspiron 1420) work properly after that only after a certain time he reported that the wireless card will not work correctly. Now, the laptop does not connect to my network more, even with cable LAN, I checked the Device Manager and I found a yellow exclamation on the Microsoft ISATAP #2 map then I double clicked it only to discover in its properties of this statement, "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Well, I try all I can, but the problem is still there, and the laptop won't always connect to my network, please anyone has an idea as to what I could do please answer as soon as possible. tThank you.

  Go to the website of the manufacturer of your router > make sure you have the latest Firmware in Vista for it.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  Try without commitment TCP/IPv6:

  If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

  http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

  See you soon.

  Mick Murphy - Microsoft partner

• I recently changed my ISP sky broadband and now my computer does not connect. Why is this?

  I tried all possible ways to connect this computer again to wide band wireless, but it does not connect. All other computers in the House connected without problem.

  Hi Joesafe,

  What exactly happens when you try to connect? You receive messages or error codes?

  You can read the article and try the steps to solve the problem:

  Windows wireless and wired network connection problems

  You can also get in touch with the broadband provider for help on the issue:

  http://helpforum.sky.com/

• Send a message that the computer does not shut down properly after the resumption he out of the hibernation mode.

  My laptop has Windows Vista and is about 3 years old.  It is in excellent shape, but recently it has been brought to my attention that whenever I put into hibernation mode and resume, I receive a message that indicates that the system or computer is not stopped correctly, and so I have to restart the computer.   Why is this happening? and any solution for this?   Thank you in advance.

  Hi SuzanneSchwester,

  Thanks for posting your query in Microsoft Communities. It seems that you are getting a message that the computer is not shut down properly after the resumption he out of the hibernation mode. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  Follow the steps in the article.

  You have problems after you resume Windows Vista from sleep or Hibernate computer

  You can see these articles for more information:

  Solve power problems

  Turn off a computer: frequently asked questions

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• 7 original slate does not connect to wifi after update

  My daughter-in-law has a 7 Slate origin. It was working fine; connected to our wifi without problems, etc. I used it the other day and noticed there was an OTA update so I installed. Now, the Tablet does not connect to our wifi at all. I tried to do a factory reset, but it still won't connect. You can see my SSID and seems to try to connect; the wifi symbol shows the signal strength but gray remains and refuses to turn blue and complete the connection.

  Is there anything else I can try to make it work?

  As a contributor of top of page on the Forums of media consumer, HP, HP gives me access to the HP Slate 7 more free of charge so I can better answer questions on the Forum.

  Why not to delete the network connection original, that you used to connect to your router and then scan for wireless devices?

  @abo999

  As seen in the screenshot below pictures, go to the settings--> Wi - Fi and click on your SSID and then click on forget. Scan and when you see your SSID again click on connect and provide the password. This should work for your question.

  

  

  Once you have done this, connect to the SSID of your router again.

  The nice thing about operating systems, it is that there are usually several ways to attack and possibly solve the problem.

• Computer does not connect to the printer epson stylus CX3810.

  Original title: computer will connect to the printer because the loader program does not list the stylus CX3810 epson and I can't find a few good sub. The printer worked ok before two days ago.

  Can not recharge my Epson stylus CX3810 because it is not listed in the list of available printers. It worked fine yesterday.

  Hello

  1. what operating system is installed on the computer?

  2 have you made any changes to the computer before the show?

  Method 1: Uninstall and reinstall printer

  See the following article:

  Install a printer

  http://Windows.Microsoft.com/is-is/Windows7/install-a-printer

  Method 2: Because it worked yesterday, you can restore the computer to a date where it worked fine before.

  Reference:

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

• My computer does not connect to facebook, it keeps displaying the message "a connection expires", how fix this?

  Whenever I try to access facebook.com, I get a message telling me that there was a problem loading the page, the connection has expires. This only happens with facebook. How can I fix?

  Hello

  Thanks for posting your query in Microsoft Community!

  I see that you are facing problems accessing Facebook.

  Do not worry! We're here to help.

  Quick questions:

  1. which version of Internet browser are you using to access Facebook?

  2 is the issue limited to Facebook?

  3 did you changes to the computer before the show?

  4. What is the full error message?

  Come back with more information so that we can help you better.

  If you are using Internet Explorer Please refer to these methods and check:

  Method 1:

  Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base. How to back up and restore the in the Windows registry: http://windows.microsoft.com/en-us/windows7/Back-up-the-registry

  You can try the steps from the following link and check if it works:

  Internet Explorer error "connection timed out" when server does not

  http://support.Microsoft.com/kb/181050

  Method 2:

  You can try to optimize Internet Explorer and check to see if that fixes the problem.

  See this link for more information.

  How to optimize Internet Explorer
  
  http://Windows.Microsoft.com/en-us/Windows/help/Internet-Explorer/slow-five-tips-to-boost-performance
  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  I hope that helps!

  Come back with more information so that we can help you better.

  If the problem persists, or you need help with Windows, please keep us informed.

  We are to help you.