Computer laptop (A60) does not start

Similar Questions

• Satellite Pro A60 - does not start

  My A60 will not start. The power supply is plugged with a green light on the power supply and the A60. The battery is full (light began in orange and is now green). Nothing happens when you press the power button.

  Tried to take the battery out and running on AC, but no change.

  Any ideas?

  Thank you
  L

  HI Laurent,.

  Try to remove the battery and also diconnecting the AC power for a few minutes. Then re-install the battery and try to turn on the unit. If this does not work, then remove the battery and plug in the AC power. Again try to power on the device.

  If none of the above works then you will need to refer to a Service partner authorized to have the laptop checked.

  Kind regards

• Computer laptop Compaq could not start

  My laptop model is Compaq Presario CQ40-502AU. I used it for over 2.5 years.

  Recently, the laptop could not start from time to time. The LED flashes to keep, but the laptop does not start.

  Referring to this article:

  http://support.HP.com/us-en/document/c01732674

  I preformed hard reset and manged to get the laptop starts. However, the problem after several days reappered and perform a hard reset is not enough to start the laptop. Sometimes, I need to do the hard reset many times to start the laptop.

  I recorded a video on the State of Flash of the LED.

  https://SkyDrive.live.com/redir.aspx?CID=4aa65a2248b908f1 & RESID = 4AA65A2248B908F1% 21412 & parid = 4AA65A2...

  I don't know if it qualifies as keeps flashing indicating the problem on my adapter?

  Someone please help me on this. Thank you!

  Greetings,

  Disconnect the power adapter and remove the battery from the laptop. Once this is done, press in and hold the power button on the PC for a minute. Only reconnect the AC adapter and try to turn the unit back on. If this problem persists, turn off the device by pressing the power button for 8 seconds. Disconnect the power adapter and the battery. Try to start the PC again.

  If the PC starts, during the Compaq logo, press the ESC key to enter the boot menu. While in the boot menu press the diagnostic mode (should be F10) and run a diagnostics of complete systems. That should tell you which device is a failure. I hope it's nothing serious, maybe a defective battery.

  If your system seems to be stable during the startup and shutdown not randomly on its own, I would try to update the BIOS once started in Windows by downloading on:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-86224-1 & CC = US & DLC = in & LC = on & os = 4062 & Product = 3973096 & sw_lang =

  Don't forget to follow directions exactly as displayed on the HP site.

  Good luck
  Brent

• Computer Windows 7 does not start

  I closed my computer with windows 7 and it was downloading some updates, and then he stopped. After closing, I tried to erase any power left in my shooting off the power system and pressing the button of power supply but I forgot the turn the power off and I started the computer, then I immediately shut down the computer. He did get to any screen startup. I turn on the computer and it would not start. The light on the monitor did not any signal and led on hard drive and then went away. Now the computer will not boot even in bios. I remove the cmos battery and put it again to reset the bios, but not luck. I don't have a recovery CD because it is a system of pre-build by HP. need help ASAP!

  Try the last known good configuration:

  http://Windows.Microsoft.com/en-GB/Windows7/using-last-known-good-configuration

• Satellite Pro A60 does not start: missing or damaged config.sys

  Hello

  I turned off my computer Friday, I went back to his Monday - and it won't start. I thought that the config.sys file is missing or damaged.

  I tried all the usual methods - safe mode, last known good setting, OS etc, but none of it works. The computer does not recognize that the recovery CD is in the drive, either.

  As I don't have an original installation CD - the computer was shipped with the software already installed - I can't try either.

  I want especially to recover the entire system, but if I have to, I can live with that. Any suggestions would be welcome.

  Thank you very much.

  RONMAC

  Have you tried to boot your PC and press C after POST message? Recovery CD to be inserted.
  This C command forces the laptop to boot from ODD first.

  Maybe it works for you.

• Computer laptop XP does not appear in the network of Vista laptop

  My cell phone based on Windows-XP does not appear in my laptop Windows Vista-base and is not accessible from this Vista computer, but it appears in the network adapter connected to the network wireless by a double dashed line. At the same time, the laptop Vista appears in computers on the XP network and is accessible from there. I have already applied Windows XP - SP3 hotfix KB 922120 to XP laptop and checked the firewall on both machines (Exceptions) settings, and they seemed OK. Also, I checked the HKML restrictanonymous DWORD value data value data (0) of the XP machine.

  Can someone help me with this? Thank you so much in advance.

  Hello
  Maybe this can help.

  To get best results connect to each computer system screen and set all the computers to be on a bearing the same name of Working Group , while each computer has its ownunique name.

  http://www.ezlan.NET/Win7/net_name.jpg

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted
  Please Note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic.

  If you end up with the 3rd party software uninstalled or disabled, make sure that Windows native firewall is active .

  Vista file and printer sharing - http://technet.microsoft.com/en-us/library/bb727037.aspx

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040

  In Win XP Pro with simple sharing Off, you can visually see the Permission/security level and set them up at your convenience.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP - http://support.microsoft.com/kb/875357
  Windows XP Patch for sharing with Vista (no need for XP - SP3) - http://support.microsoft.com/kb/922120

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  -------------

  If you have permission and security issues with Vista/Win7, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  * Note . All the users who are allowed to share need to have an account onall computers that they are allowed to connect to.

  Everyone is an account, that means a group of all users who already have an account now as users. It is available to avoid the need to configure permission for each on its own, it does not mean all those who feel that they would like to connect.

  -----------

  If more control is needed to take a look at this page http://windows.microsoft.com/en-US/windows-vista/Share-files-and-folders-over-the-network-from-Windows-Vista-Inside-Out

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• Pavilion laptop g7 does not start

  I have a HP Pavilion g7-1167dx Notebook PC running Windows 7 Home Premium.  When I turn it on, the LED only lights are LEDs of power (on the power switch and side) and the network LED on the F12 key.  I am not able to enter the diagnostics of material via the F2 key.  The fan is operating normally. It was produced before intermittently, but I wanted to just wait awhile and it would eventually start again.  When he finally is never returned, I disassembled carefully, according to the maintenance and care, guide (on an ESD protection adequate workstation) and gave it a good cleaning.  It was very dusty inside.  Unfortunately when I reassembled it, it still does not work.  The computer is a little more than two years. Product number: LW414UA #ABA

  I sent the motherboard to repair parts of computer out of Miami, Florida and they fixed it and returned.  I was told it was the video chip.  They charged $70.00.  With each shipment way I got it fixed for $90.00.   Hallelujah!  With their setting of the original motherboard, I didn't have to worry about problems of CMOS and "tattoeing" a new motherboard, which would have cost a lot more.

• my hp laptop 15 does not start

  I used my laptop hp 15 after about 2 hours I closed the lid came back in about 60 minutes. Open the lid and looked like he was starting then the screen went black and turned off the coast when I turned it on the light came and then turn off in 3 seconds. I removed the battery and put it back on and is the same thing, I removed the battery and pluged the power cord and it did the same thing so I put the battery back and it does the same thing, so I switched back on it and opened the cd/dvd out of my drive and it sounded like he was going to start but the stad to black screen but he kept making the same sound that was yesterday and today There the light red and in 30 seconds. It turns off again there windows 8.1 64-bit x 64 processor intel (r) laptop is ome months Please help if you can and thanks for all those who try to help

  read that if I leave the battery on the pc and not plug in turn pc on bottem and hold the button for 10 seconds it would start took about 20 tries and turning the pc in different ways so that it can stay on for only 10 dry. AND CELA WORKED YAY! now the key board does not work then I used git on-screen key Board in the pc, I am now refreshing my pc to see if it works.

• I have a Pavilion a6244n desktop computer. It does not, start just beeps long short 2 and 1. Beep codes HP

  identify the video card. He has a card of Nvidia GeForce 8300GS. Because I can not start the computer, can I safely replace the card with a GeForce 520 and will recognize it and start the computer? It is almost 5 years and I have already replaced the power supply. The computer worked very well all these years and think it can last from several others. Any suggestions? And thank you for taking the time to read this.

  I replaced the video card. New card is a GeForce GT 520 Galaxy. Everything is back to normal.

  Thanks for your advice.

• Computer laptop XP does not connect to the broadband network.

  I'm trying to connect a laptop Medion XP to our fiber BB home connection using a Wi - Fi connection. However, our network (which uses the WSP) is not yet displayed in the list of available wireless networks. WSP n/w of that another neighbor (no fiber) is displayed (while I should be able to see several other networks). So I tried to connect the laptop to the router with an ethernet cable, but it still does not see the network. I checked this automatic dynamic DNS and IP addressisng is activated, and I installed the SP3 download first on my PC. However, this made no difference. Any suggestions please?

  Hi, thanks for your response.

  1. I talked to the ISP and excluded all router problem.
  2. There is only one other pc connected to the network. We connected the other phones before and never had a problem.

  According to me, it's that the laptop is old and may be damaged. A grumpy at work looked for me and we can't even get a wired connection works.

  Time it's bin and get a new one, I think!

  Thanks again.

• Laptop HP 630: computer laptop fan does not increase speed

  I had problems of heating very wrong with my pc it would tend to turn off all the tkme when it overheats, I decided to blow into the fan and dust came out. He continued to work perfectly until last night where he continued to heat up, I checked on the Internet and I found I just had to clean the fan, that's why I opened my laptop this morning and cleaned the fan. But now the fan does not accelerate if the temperature is high before her and make a horrible noise, now the fan is on, but does not change its speed when the cpu heats up! I tried a lot of freeware that increases the speed of the fan but the fan cannot be detected, but the fan is always on and idle. I opened the laptop 3 times to check if everything is connected and they are, but what could be the problem? Please help my laptop is my life right now.

  Yes I used to blow from the outside, it is very help full. I took it to get it fixed but the guy could not fix it, so he said he has tried to change the CPU and RAM, but nothing happened so I gave up. An amd box external hard drive, I bought a Hp Pavilion Dv6 of second hand, I thought my lapt lasy forever, that is that a good model does not only take care of it right. I still have faith in HP products and will soon buy a new laptop for their part again!

• I am using windows 7 and my computer laptop wifi does not connect to the modem. It worked correctly with the other modems. I had the prob with the new modem provided by optus. can someone help me please?

  my computer laptop wifi works with other modems. and my modem works with other laptops. they have one problem with each other.

  I don't know why, please help me...

  Hello Omar.

  Thank you for keeping us posted.

  It seems that you did not try the method 2 and 3 after running the troubleshooter from network. Please, try it both ways and see if that solves the problem.

  Reply with the results. We will be happy to help you.

• Pavilion dv6 Notebook: laptop still does not start if equipped upward of battery

  Pavilion dv6 daughter Notebook always primer not beyond the screen HP enrobeur battery if

  Product number: WR498EA #ABU
  Serial number: [personal information deleted]

  Operating system: Windows 7

  Hello @HPNovice1,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that your notebook always primer if if mounted battery and I'd love to help you in this case!

  Since you have already calibrated and tested the battery, I suggest following the steps below re - install the battery method compatible ACPI Microsoft control:

  Step 1. Go to the Device Manager
  Step 2. Select the stacks
  Step 3. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 4. Click on uninstall
  Step 5. At the command prompt, put a checkmark in the box to remove the current driver
  Step 6. Shut down the computer
  Step 7: Remove the battery for a minute and then put new

  When the computer returns to the top it should automatically find the driver.

  Step 8. Go to the Device Manager
  Step 9. Select the stacks
  Step 10. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 11. Click "automatically search for an updated driver.

  Do the same thing with embedded controller compatible ACPI Microsoft.

  In addition, I also recommend you to restore your laptop default power plans by following the steps below:

  Step 1. Click the Start button
  Step 2. In the search box, type "Command Prompt"
  Step 3. Right click on command prompt

  Step 4. Click on run as administrator
  Step 5. At the command prompt, type powercfg /restoredefaultschemes and press enter

  reference: http://superuser.com/questions/669571/Windows-8-1-64-bit-power-schemes-gone

  If the problem persists, please call our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps!

  Concerning

• Computer laptop Gateway does not load windows Vista, reads configuration data read error: System.

  OK a friend knows me to fix his laptop. Apparently what she was experiencing major problems, so he erased the disc and tried to reinstall Win Vista from disk. Will not work. I can get to where you can choose a partition to install the operating system to, and it says: Windows cannot find a system volume that meets its criteria for installation. My friend says he has just tried, form disassemble the computer an audit of all the parties to try ALL the different options during installation, as well as the options for the BIOS. Any ideas people? Here are the approximate specifications, because the owner has not been able to get the computer working for awhile:
  4 GHz, 4 GB RAM computer Gateway laptop, 2006, Phoenix TrustedCore, and a string of other interesting info that appears on the first screen of the error:

  9D.03 BIOS version

  632K RAM passed system
  3966M extended RAM passed
  1024 KB of L2 Cache
  System BIOS with a shadow
  Video BIOS with a shadow
  ATAPI CD-ROM: Optiarc DVD RW AD-7563 has
  Fixed disk 0: WDC WD2500BEVS-26VATO
  Initialized the mouse
  Updated System Configuration data
  ERROR
  System Configuration data read error.

  I'm not very tech savy and I'm not the owner of the PC, so I don't know all about it so go easy on me :).

  If your friend tried to reinstall Windows by using the defined gateway recovery disc (and this is the best way) and this recovery fails, the laptop has hardware problems. Disassemble laptops is a fickle business at best and while it sounds like the hardware problems started before your friend did this, it may have put the nails in the coffin of the laptop to take apart.

  At this point, you can try troubleshooting hardware or your friend can take the laptop to a competent professional (not a type of BigComputerStore/GeekSquad of the place). However, if the laptop has had hard use, your friend must remember that a cell of 4 years with major hardware problems probably won't be cost effective to repair.

  http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot MS - MVP - Elephant Boy computers - don't panic!

• Equium A60 does not start correctly

  Hey,.
  I was working on my laptop and it froze, so I restarted, but it froze again.
  When it restarts again the laptop attempted a System Check, but to try to initialize steps 3 > (newspaper?) it happened extremely slow so I restarted it.

  This time, the laptop not boot but produces a blank screen showing:
  "For (x) Realtek RTL8139 810 x PCI Fast Ethernet Controller v 2.13 /8130/ (020326) PXE - E61 Media Test fails, check the cables." PXE-MOF-leave PXE ROM.

  However, when I am sometimes inclined to my laptop, it starts, but slowly?
  I test the University, but I don't understand what to do; I took it to our technicians, and they don't know what to do. Can anyone help please?

  Hello Joseph

  I assume that the HARD drive is at the end of his life. Like written Marina trying to check if you have access to the HARD drive otherwise, I think you need to buy new HARD drive.

  Please let us know if you will find what is the problem.