computer laptop Windows vista may not start

Similar Questions

• Computer laptop Windows XP does not start? Help

  Hi I have a windows xp laptop I think that their system eis or something like that... Whenever I start the laptop, he's going on the error you get when your dosent laptop shut down correctly. If I click on start normally the bar will spend about a quarter of the way and then just stayed forever and only safe mode also gets a freeze from then. Y at - it something wrong with the laptop or what. How can I get my laptop to work again... someone help me please.

  It is up to tell you to us what brand of system and the model is... not "system ist or something like that."

  When you choose to start safe mode and you can see all the stuff being loaded and the system crashes, which is the last line on the screen to say?

  If you attached an external equipment, especially USB devices, disconnect everything and then you can see if things seem better.

  If you get an error message windows system config, exactly what he says?

  No error paraphrased messages please!

  It was something like this:

  Windows XP could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM

  Which usually indicate some sort of corruption of system files may be a loss of power, aborted reboot or abnormal termination? (This includes the plug pulling, buttons power and removing the battery).  None of this seems familiar?

  If you can boot from a CD, you can create a CD bootable XP (no XP media required) Recovery Console and run chkdsk with correction of errors on the afflicted to start System.

  Here's how:

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget what you have (no XP media required).

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

• Computer laptop Windows XP does not start.

  My laptop does not start. When I first put it on the screen says 'we apologize... ". Windows does not start automatically in... "Then the Windows XP screen as it tries to load there is this small blue screen that appears a second microphone, too fast to read, then goes back to 'we apologize...". "screen just keeps looping. I thought that my hard drive was going badly, so I ordered a new. I have XP SP3. Could someone help me please?

  Hi robestes3,

  1. When did you start to question?

  2. you remember to make changes to the computer before this problem?

  Method 1:

  First of all, you can tryLast good known Configuration and check if helps solve the problem.

  Check out the link:

  How to start your computer by using last good known Windows XP Configuration

  http://support.Microsoft.com/kb/307852

  Method 2:

  Step 1:

  If the above method does not work, then you can try to start in safe mode and check if the problem occurs.

  Check out the link for more information on starting your computer in SafeMode below:

  http://support.Microsoft.com/kb/315222

  Step 2:

  If you can boot into safe mode without any problem, and then try to perform a clean boot. A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  http://support.Microsoft.com/kb/310353

  If your problem is resolved after the clean boot, and then follow the steps mentioned in the article above to refine the exact source:

  In addition, after you resolve the problem, see the section on how to restore your computer to a Normal startup mode.

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows Vista does not start upward, with success since the closure complete

  Hello world

  I actually had this problem for a long time, but I'm just now to a point where I'm ready to take a lead in fixing it.

  I can't identify when it started, but Windows Vista does not start upward, with success of a full stop. He gets to the screen where, in general, the green bars will travel across the screen, but the green bars will not come. The screen looks dim and sits there, with the text of the copyright of Microsoft Corporation. So, after not having on the mound, I have to manually shut down the computer by holding down the power button. When I try to start again, told me to go through the Startup Repair tool. If I jump the repair, I just have to meet the same problem - a computer that will not go beyond the screen "green bar".

  So, I do the Startup Repair, and told me what I do for the restoration of the system. Windows starts normally after the restoration.

  Don't forget, this happens from a full stop. To remedy this, I just never completely shut down my computer. I left running and back just at the beginning of the day. The computer may start restart, it just may not start with a full stop.

  Given the start of repair takes, literally, around 4 or 5 hours of full stops complete, accidental or power outages are a nightmare, I am obliged to wait 5 hours to get access to the computer. Fortunately, I have my laptop.

  If someone has encountered this? I saw people talking about the loop of startup repair, but that's not the point, I have. I have yet to see any discussion of my specific problem.

  Thanks in advance!

  Hello

  4-5 hours to do a startup repair is too long.

  Often you get better results if you a using a DVD of Microsoft Vista startup repair.

  Jose how to do a startup repair, etc. using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  See you soon.

• Windows Vista does not start, turns to a blue screen error 2203

  original title: Windows Vista does not start, turns to a blue screen HELP PLEASE!

  Help, please! So I'm panicking here, just yesterday, I tried to download the update to Itunes, and it did not work. So I followed the instructions and uninstalled the program first, but one of the applications does not uninstall correctly. I thought I could just substitute with the update and replace. The error code was 2203.

  So I thought it was right after the download all itunes thing, and when I came back to check on the download, the screen turned to this black thing with words on this subject. I decided to force closing down by pressing the power button. Now everytime I turn on the computer, it leads to the screen saying 'windows is loading files', then this blue screen with a very large arrow (the mouse). I tried pressing the F11 key and stuff, but I have no idea what to do. PLEASE REPLY AS SOON AS POSSIBLE, REALLY NEED A COMPUTER!

  "I tried to do the second option, because the first really helped."

  Something works, or it doesn't work regarding: "really helped."

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  I'm sorry, but I don't understand where the procedure of ISO part 2 stops.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  You may be interested in this:

  Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  See you soon.

  Mick Murphy - Microsoft partner

• computer laptop Windows 7 saves not CD / dvd

  my computer laptop windows 7 is no recorded any cd / dvd... Ive checked everything on my computer and online, but couldn't find a solution! does anyone else have this problem? If so how do solve you this problem? Help, please...

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and

  
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Windows Vista does not start - only Safe Mode

  Hello

  Windows Vista does not start. Starts only in Mode safe. Same system of recovery is not backward by date

  Press F8 all turn the laptop.
  Choose the first option: by computer repair and try to repair the operating system automatically.

• Windows VISTA does not start - shows a green bar horizontal scrolling forever, safe mode stops at crcdisk.sys

  Windows Vista does not start.  It shows the horizontal scrolling green bar with microsoft (c) and then goes to a black screen with the mouse arrow that moves. Start in safe mode loads the drivers to the extent of the crcdisk.sys but meet once again at the black screen with the mouse arrow.   Have not the SATA drives connected.  Impossible to get to the command prompt to delete all files.  No work from safe mode.  Restore computer does not work.  I have looked at other posts regarding the renaming/deleting files, but cannot get to the command prompt to resolve this problem.  The computer is less than 2 years.

  Toshiba Satellite A205-S5831, dual processor running.  Running Windows Vista BASIC.  Hard drive seems to work, lighting, well working properly, no error at startup.  No perifpherals or a mouse, or a USB attached.  Disabling USB does not boot.

  Can someone give a help?

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > find the latest Vista drivers for it > download/install the

  See you soon.

  Mick Murphy - Microsoft partner

• Windows Vista does not start after installing Linux OS

  original title: Windows Vista does not start after the installation of the Linux OS... Help!

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  I installed Fedora 10 Red Hat Linux on my HP laptop and now each time it powers on, I can't do vista windows at startup.  Goes directly into Linux.

  I need to get back to normal.  Any help would be appreciated.

  Hey Oscar Jose

  Download the correct ISO file and make a disk bootable from the link below

  Then use the Startup Repair option when you start from

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  or at startup press F11 to start the process of restoration of hp and see if you can reinstall vista from the recovery partition and place your machine, back to the way you bought

  warning you all data loss and 3 third-party programs that you have installed unless there is a non-destructive option in your hp recovery options

  Thirdly try to ask in a fedora forum to solve the problem, he has caused

  http://fedoraproject.org/

  Walter, the time zone traveller

• Update of Windows Vista does not start - remains just white

  I have a new computer with Windows Vista Home Premium installed. I have updated the computer with windows updates by using the Windows Update tool.
  However, it has stopped working and I can no longer get updates or visit the update page.  I know that there are updates to install but when I open windows update, the schedule is displayed but there is nothing in it.  That is to say: in the browser bar, it says: > Control Panel > Windows Update, but the window is otherwise empty and nothing loads.  I have no error messages.  I tried to close the program, but it does not and I have to close it using Task Manager.  I also rebooted the computer several times and tried to leave for an hour or two, but still nothing happens.

  How can I update my computer?  or even reinstall windows update?  I think that the program is may be defective...

  Hello Christopher,

  I'm sorry that you have problems with your Windows Update. It takes a little the pleasure of having a new computer isn't?

  Try a few bugs, starting with the easiest:

  In the Vista Start Menu Search Bar, type run and press ENTER.

  Then, type the following, one after the other and click OK after each.

  regsvr32 jscript
  regsvr32 vbscript
  regsvr32 /i mshtml

  I hope it will work for you. If this isn't the case, you can try the following:

  Note: The following assumes that you have, or have access to the
  original Vista 32 - bit .iso or can otherwise use the file
  in the .iso image file install.wim.

  1. place the original Vista .iso image file on your hard drive.
  2 extract the iso install.wim.
  3. extract all the files from c:\windows\system32\wu*.* install.wim.
  4. place all the excerpts wu *. files in their own folder, for example, C:\wu for
  later use.
  5. run start, all programs, accessories. Right click on command prompt
  and click on run as administrator.
  6. go to your System32 directory.
  7. to replace current wu *. files in the System32 directory.
  you will need to first ownership of each of them as follows:
  Run: takeown /f "path and name ' [note: I ran this command for]
  each of the wu *. [* files, one at a time]
  then
  Run: cacls 'path and file name' / g : F
  8. replace all the wu *. files using those c:\wu
  9 save each of the original wu*.dlls in System32 - for example
  (regsvr32 c:\windows\system32\wuapi.dll)
  10. reboot
  11 place Windows Update in manual mode as a test and run it.

  If please post here and let us know if this helped.

  Thanks Dave D
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My HP laptop with vista does not start.

  Vista will not start. Startup Repair says it cannot start automatically. Stuck in a loop without any difficulty.

  Hello

  Please tell us the brand and model of this computer. Also, you happen to still have discs Windows Vista of origin that goes with it?

  Looks like we'll have to try to recover directly from the CD so if you don't have it, I would like to talk with the manufacturer of the computer for another copy

• Windows Vista will not start and cannot recover

  I have a desktop PC HP Compaq Presario, which has about 2 years. The problem started when Windows Vista was not able to start. It would load up on the "COMPAQ" screen and then it would just go to a slider black white screen with a flashing white light on the top left. Now that I've seen a lot of discussions with this similar problem, but it seems that people would rather not reformat in order to lose any important data. But in my situation, I have some important data on my computer so reformatting would be fine, except...

  -Recovery system won't work. I insert the 1 system recovery disk, all files loading correctly, it allows me to choose if I want to reset the computer to factory settings, I click Yes and it finishes the reformatting step. But then the problem comes when I insert disc 2, original content relocation step. It fills up to 10-16% and then I get a blue screen of death STOP: 0 x 00008086. I tried SEVERAL times and the same thing happens.

  -The next thing I tried to do is to fix the computer via a copy burned Windows Startup Repair. Loads everything up, I spent the page where I choose my language, currency, etc. The problem comes when I get to the System Recovery Options. There is no listed BONES and a box appears and says "Searching for Windows installations", and then it stalls just on this pop up. This problem is quite recent, because before there is no pop up and there is simply no OS listed, so I still could not repair or restore in any case.

  -Before, when I was able to go into the advanced options on the Startup Repair disk (when he was not of "searching for Windows installations" pop up to stall on), I'd go to the command prompt in attempt to chkdsk/r C:. All bad sectors or groups or something else would be fixed, and then he would hold to step 5 of 5 when checking free space.

  -In addition, I tried to make a diagnosis of memory via the Startup Repair tool. That's what I get:

  File: \boot\memtest.exe

  Status: 0xc000000f

  Info: The selected entry could not be loaded because the application is missing or corrupt

  
  

  Furthermore, I cleaned my computer, it is now almost completely free of dust. In addition, I can't get into the BIOS, I can't get into safe mode, and now I can't have in the command line

  Hello

  If you are unable to enter the BIOS and all the other problems, you have hardware problems
  and need the help of a real store of the computer (no leeks and glances at a Best Buy or any other
  Department stores) or Support of HP/Compaq.

  Compaq Presario Support
  http://www.Compaq.com/country/cpq_support.html

  Forums for HP/Compaq
  http://h30434.www3.HP.com/PSG/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Interrupted for laptop - Windows 7 does not start

  M6 computer - laptop - HP pavilion

  Operating system - Windows Home Premium

  Unfortunately I dropped this computer from a height of 4 feet after closing it.

  Since their start-up is not possible.

  I started the "the option computer repair"-it seems to start but then hangs indefinitely.

  Al the other options safe mode, safe mode with networking, etc., including "start windows normally" do not start and all back to 'Repair your computer' which still once blocks indefinitely.

  I tried to get the recovery option by turning on the computer by pressing F12 repeatly before the windows logo appears.

  The system recovery words appear, but I again picked option 'Repair your computer' which once again blocks indefinitely.

  Advice please - the situation seems hopeless. ?

  Concerning

  Flynne

  ______________________________________________________________________________________________________

  Thank you for your quick response.

  I managed to get the option of recovery has begun and now my computer works well.

  I ran a disk check and all sectors appear to be intact.

  I'm very lucky to get away with this.

  I have discovered that my computer is equipped with a device that limits or prevents damage to the hard drive.

  Thank you for your interest.

  Concerning

  EFLYNN

  _______________________________________________________________________

• What to do with my computer laptop windows vista which does not start? He gets a screen before before her windows error recovery screen restarts.

  Tittle says it all, I tried safe mode and the rest of them, but I can't start

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Installed new module memory for laptop, found original was bad, while windows Vista does not start by going blank after the "status bar".

  I have a Windows Vista running on a Sony VIAO laptop and has been updated with level 3 to 4 GB of memory. During the memory test, I found that 2 GB of original module was bad and replace it with the new 2 GB module end back where I started with 3 GB. However, Windows starts only at a little past the rectangle with 3 points moving ("State Bar"?) and them it goes to black and the desktop never appears. I tried to roll back to the last working version of Windows settings, but always the same results.

  What can I do now? Is there a way to check and fix disk errors?  Is it possible to install Windows XP Pro or I have to go to Windows 7.  I even has System Mechanic Pro running on this laptop and it did help some casued the problem. It's as if the disc is damaged for some reason any.  Only with Vista felt this helpless.

  It seems to me that the new memory you have installed is bad or incompatible with the system.  First, remove all chips and reinstall them and then try to make sure that they are correct and secure again - don't just press them in place, effectively remove and the replacement and make sure they are in the right direction.

  Boot from the Installation of Windows Vista genuine disc (or you can borrow from someone) or a recovery disc with recovery options included in this topic. If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD (perhaps made on another computer, or perhaps in SafeMode with network if it does not - that would be a good sign if it is true). You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.  Select recovery options and follow the instructions until you see the menu.  Once there, select the Windows Memory Diagnostic tool and run it and see what it says.  If it detects problems (and I suspect it might), you may need to replace the new chip memory.

  I hope this helps.  If this isn't the case, after return and we will try other options.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.