Computer opens in the BIOS after reboot

Similar Questions

• ESXi 5.5 build 2456374 is unable to reconnect to the vcenter after reboot

  Hello

  Have been hitting my head against it for the past few weeks. A host that has worked very well to a previous 5.5 build fails to reconnect to the vcenter after reboot once upgraded to build the 2456374. This also happens to the newly built guest. When a reconnection is started manually, it produces up to 80% (data of the host processing), then dies with a "general system error: internal error. I tried to remove the vpxa account, resetting the config network via the console, Cup NIC of the vswitch, removal of additional interfaces vkernel. The network via the console configuration reset allows me to reconfigure the net and tie vcenter and complete the host host configuration. However, as soon as I restart the host, is no longer, it reconnects to vcenter and I'm back where I started.

  Unfortunately, this is not a 100% event. If I rebuild a host enough times, one of the new buildings will finally works correctly.

  any ideas on how to solve this problem would be appreciated.

  Elmārs

  QUESTION REOLVED!

  Ok. so that was the easy part. Open a folder with vmware to identify the cause for this. After much digging, friction, pull hair, we found a clue in the hostd.log on the ESXi host.

  2015-04 - T 02, 04: 49:05.481Z [23381 B 70 error 'Hostsvc.NetworkProvider' user opID=HB-host-185064@917-1d029f4d-d2 = vpxuser] an error occurred during extraction of stack instance configuration: incompatible value of ccalgo for the Netstack instance: defaultTcpipStack.

  In my network performance test I did recently, I have significantly improved network iSCSI performance from the cubes NewReno network congestion control algorithm. For each of these hosts, as part of the installation procedure I now set the control algorithm of congestion on cube through the web interface. Finally, it is a little bug with that VMware believed fixed. Is not.

  To confirm doubling you encounter this problem, connect to the host (ssh or remote cli) and run the following command:

  list of esxcli ip network netstack

  You should get a message saying that there is an inconsistency in the netstack configuration.

  To fix, run the following command:

  esxcli network ip put netstack defaultTcpipStack cubic n - c

  the netstack from above list command should now display detailed information and will now be able to connect to vcenter.

  If I understand correctly, an article will be published on this in the near future.

• Have been left in charge all night I get the message "after reboot requires the password" question is why is this automatic restart, and is this normal

  Have been left in charge all night I get the message "after reboot requires the password" question is why is this automatic restart, and is this normal

  Occasionally, it may restart because something was wrong. It is not a problem unless this happens frequently.

• My computer will display the BIOS boot screen then do nothing yet, I insert the Windows installation disc. What should I do with it?

  My computer will display the BIOS boot screen then do nothing yet, I insert the Windows installation disc and I press F11, 12 > no response, F10 > BIOS Setup. What should I do with it?

  Brand: HP
  Type: laptop
  Model No.: Pavilion zt3000
  512 MB DDR1 RAM
  Thank you very much!

  Hi Dominic,

  Are you able to get into BIOS to make changes?

  If so, you can try to reset the default settings of the BIOS and check.

  NOTE: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  You can also try to remove all external usb devices that can be connected to the system and start-up and see if the system boots.

• I restart the computer and changed the BIOs to boot from the CD. So as usual, I'm prompted to press any key to start from the CD or DVD.

  Hello Comunity Microsoft :D My name is Mike and I built a gaming pc. Everything was going well for the first 3 days, but now I have a few crashes very violent. Speakers in loop and buzz and screen lock. I have to completely shut down to go back to a working state. I did everything I could possibly think of to solve this problem, but I can't.

  Then. on the problem. Today, I decided that I was able to solve all the problems by reinstalling windows. I had my keys together and put the disc in. I restart the computer and changed the BIOs to boot from the CD. So as usual, I'm prompted to press any key to start from the CD or DVD. I do and I get normal loading windows files, and at the end of this road, I get the Welcome screen in windows7 with no option and a fat slider. I don't have the little box that tells me that I can fix my computer or reinstall windows, NOTHING. I tried several times and received the same result<--(Insanity: root="" meaning...="" just="" saying)="" so="" i="" called="" windows,="" or="" had="" windows="" call="" me="" rather,="" and="" the="" tech="" says="" she's="" never="" heard="" of="" such="" a="" thing="" happening,="" and="" walked="" me="" through="" all="" these="" steps="" that="" i="" have="" already="" tried....="" still="" no="" help.="" so="" i="" am="" asking="" the="" community.="" has="" this="" ever="" happened="" to="" you="" and="" how="" did="" you="" make="" it="" work.="" and="" please="" don't="" post="" a="" list="" of="" regurgitated="" back="" log="" fix="" lists.="" rest="" assured="" i="" have="" already="" done="" it="" and="" failed="" to="" receive="" a="" different="">

  Just to isolate the problem, try to download a new copy of Windows 7, and then try again:

  For 5 years, Microsoft made it fairly easy for users of the Windows 7 operating system to get reinstall media. If you have lost your support disc or installation retail collection; either it has been damaged or defective; You can download a copy of the edition that you have licensed from a membership site called Digital River. More recently, Microsoft ended the availability to reinstall media that you can download as a. File ISO in Digital River, which is a digital reproduction of an optical disc.

  It was particularly convenient for people who could not easily get the manufacturer's recovery media, did not want to pay the fees required to get or preferred a clean configuration without the software packaged manufacturers or even a recovery partition does not work. It's easy to use, all you had to do was reinstall and reactivate using the product key located on the certificate of authenticity and download all the drivers on the manufacturers website.

  Given that this option is no longer available, what are your options? See the article for more details:

  How to: What are my options for Windows 7 reinstall media?

  Make sure you scroll down and read the section:

  What to do if you cannot get your manufacturer recovery media, refuse to use or to buy it or the Microsoft Software Recovery Website does not work?

  Regarding problems with the computer itself, try to disconnect all nonessential equipment attached to it to see if the problem persists.

  I would also try switching around components such as modules of memory to see if the problem persists.

  I would also check to make sure that all components are mounted and installed correctly.

• Hello muse adobe at the opening of the program after entering my account details, he said an unexpected error has occurred, what do I do

  Hello adobe muse during the opening of the program after entering my account information he said: an unexpected error has occurredwhat should I do

  Just sign in and out Adobe Muse and creative cloud, then restart the program.

  Check out my website LJDezignz.com

• After that update the BIOS cannot reboot my Satellite A200

  I did the bios update for the trueearnings tol, just instructrion restart so I can't reboot my computer, then, what can I do?

  Hello James

  It sounds pretty bad for me. It is typical behavior if the BIOS is damaged.
  What you can do? Unfortunately not much besides make the closest meetings of Toshiba authorized service provider and ask for help.

  I'm sorry. :(

• Satellite L850 - opens the BIOS on reboot, even if no one press F2

  My laptop opens if restarted BIOS through Windows, even if no one supports on F2, but this only happens when I stop. I recently updated to the latest version of Windows updates. Funny, it's guaranteed expired 2 days ago. I had to manually, press the power button just started my unit.

  The unit is a model of Satellite L850-B150.

  > My laptop opens if restarted BIOS through Windows, even if no one press F2, but this does not occur when I shutdown

  I understand this correctly?
  The laptop and the system works properly. If you click on restart the device stops, then boots to the top and switches in the BIOS.
  Is this correct?

  Hmm its really strange.

  To be honest, I don't think that its a software issue related because no application is able to access the BIOS directly after the POST (power selft test) has been produced.
  This is why I think it could be a motherboard problem material? Keyboard? I m not quite sure

  However, go to BIOS (F2) manually and set it to default settings (F9). Save the changes and restart the device.
  Check if the device would still access the BIOS automatically.

  In which case the matter would be always available, recover laptop using Toshiba recovery media.
  This would create the laptop back to factory settings.

  Finally if this is insufficient, the device must be checked by professional service guys.

• SSD not detected in the Bios after stopping

  Hello

  I bought a SanDisk SSD II specially 2 days.

  I plugged it in the first my motherboard SATA port and a SATA power cable. Then I started up my computer and installed Windows 7 Pro without any problem on the SSD, but after I shut down the PC, the SSD is not longer detected in the bios.

  The thing is that if I enter the BIOS, the SSD is not detected the first time, but if I restart the computer it will be detected on the next launch.

  Identically, Windows, if I do a "reboot", everything works fine, but if I make a stop, then SSD will not be detected the next time I start the computer.

  Do you think I should return the SSD?

  Thanks in advance

  I fixed it by choosing the AHCI mode (instead of IDE).

  FYI, my motherboard is an Asus P7P55D.

• Satellite A350 - 12J Faliure of the BIOS after update.

  Hello world.

  I am owner of Toshiba Satellite A350-12J (it's the PSALME series). Recently I received the message in Toshiba Tempro, having said that I should update my BIOS, so I decided to do. I downloaded proprer version from the Toshiba site, which was 1.5 and follow the instructions to update (I want to mention here, this isn't my first update of the BIOS). After that update was done to my restarted laptop and does not start again. The screen is black all the time.

  When I try to turn the fan runs for a few seconds and then goes down, there is an activity in the USB and DVD devices but it's only for a few seconds and then more nothing.

  Oh, almost forgot that HARD drive also works. I read that in the Phoenix based BIOS there is that something called crisis recovery, so I tried, laptop starts in this mode (I can say, because in it is fan of fashion goes up to system and RPM max tries to boot from USB Floppy).

  I tried crisis Revovery in several combinations and during the process, it seems that it is flashing my BIOS (crisis recovery disk whith Floppy is read for about 2-3 minutes), but after I wait and give him time to reflash (10-15 minutes each time) for computer laptop stiil starts.

  I think that maybe this version of BIOS (1.5) is bad or something. Maybe Somone have original BIOS for this laptop, I would be very grateful for these BIOS or maybe someone has an idea of what is wrong there.

  In case someone has the original BIOS was kind enough to send me, here is my email:
  [email protected]

  I ' sorry for my English, it is not my mother tongue.

  Hello

  > I have a Toshiba Satellite A350-12J (it's the PSALME series).
  It s NOT PSALME series but series PSALWE!

  > I decided to do. I downloaded the correct version of the Toshiba site, which was 1.5
  On the page of Toshiba Europe, I find the BIOS update version v2.10

  However, there is only one real solution;
  You should get in touch with ASP in your country in order to solve this problem.

• ThinkPad Yoga, can not change the settings in the BIOS after upgrade

  Hi guys,.

  I just flashed BIOS on my thinkpad yoga 20CD00B1US.

  I got the lates BIOS 1.18/1.09 and sice this flash, I can't make changes in BIOS. I may list in the BIOS but can't highlite and change any setting expect fast start enabled

  My Manager the same get me this warrining: the controller board (EC) returned data when none was requested. The BIOS may try to access the European Community without synchronization with the operating system. These data will be ignored. No further action is necessary; However, you should check with the manufacturer of your computer for an updated BIOS.

  I have put the supervisor for the BIOS password password to power on. When you go into the BIOS, I ask me to put the password, which could be the problem. But why, I have no idea.

  Help please!

  Sorry guys,

  problem sorting, my password BIOS supervizer was different from the power on password, always when I was promt to password, I put here one for power and he let me go in BUT when I wen in the BIOS, I was not able to access the settings.

  After I set supervisor password good everything works how suppose to.

• How to recover the BIOS after erasing the CMOS RTC RAM?

  My HP a6541sc froze during the update of the BIOS (using sp44500.exe found here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=pv-82094-1&cc=no&dlc=no&lc=en&...)

  After that, I get a black screen and some components running inside the wardrobe.

  I erased the RTC of RAM according to this info: http://support.hp.com/us-en/document/c01357175

  Now, I would like to know if there is anything I can do to save my computer? I found information on starting a new BIOS from USB, but I need help on what to do. How can I Flash a new BIOS?

  System:

  HP a6541sc

  Vista 64-bit

  Thank you!

  Thank you. Unfortunately I couldn't interest the BIOS screen and I had to get a new BIOS chip. This solves the problem.

• How to turn the computer back at the office after sleep?

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: this is the 1 time I use the function slee...

  • I don't know how to get back on the desktop after using sleep.i cannot find any button to return, as seen as running off.whay should I do...
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Usually just move the mouse or using the keyboard wake it.

  1 I want to erase the General corruption and repair/replace damaged/missing system files:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------

  Check the settings (BIOS/CMOS) that you can start and ensure that this suite of lan, Wake on modem and
  similar are not enabled.

  Shoot sleep problems - hibernation
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  All the default power plans and then set them as you wish.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Access to the BIOs after Windows 10 upgrade

  Hello

  I recently improved my 8300 small form Factor Desktop of WIndows 7 window 10 HP. I need to access my system in the BIOS and have trouble making. I need to access my system BIOS in order to activate Intel VT - x, so I can create a Ubuntu Virtual 12.04.5 by using VMWare Workstation.

  Here's what I know:

  -My system has no parameters UEFI when I restart the computer while now shift then click on "Troubleshooting > advance Options.»

  -Pressing keys such as ESC, F1, F2 and F9 - F12 do not take me to the BIOS. Instead, they take me to the next menu;

  -Esc: Start Menu

  -F2: HP PC Hardware Diagnostics UEFI

  -F9: Please select Boot Device Menu

  -F10: Hewlett - Packard computer put in place

  -F11: System Recovery

  -My BIOS is inheritance according to my request for information system.

  -J' have an Intel Core i5-3570, clocked at 3.4 GHz

  My questions are:

  1 should. what course of action I take to access MY BIOS to activate Intel VT - x?

  2. I plan to the system through the Legacy BIOS mode BIOS flashing.  Am I wrong?

  3. is there another way to activate Intel VT - x without access to the BIOS?

  If anyone can help I will be greatly appreciated. Thank you!

  shaw_brandon wrote:
  

  Hello

  I recently improved my 8300 small form Factor Desktop of WIndows 7 window 10 HP. I need to access my system in the BIOS and have trouble making. I need to access my system BIOS in order to activate Intel VT - x, so I can create a Ubuntu Virtual 12.04.5 by using VMWare Workstation.

  Here's what I know:

  -My system has no parameters UEFI when I restart the computer while now shift then click on "Troubleshooting > advance Options.»

  -Pressing keys such as ESC, F1, F2 and F9 - F12 do not take me to the BIOS. Instead, they take me to the next menu;

  -Esc: Start Menu

  -F2: HP PC Hardware Diagnostics UEFI

  -F9: Please select Boot Device Menu

  -F10: Hewlett - Packard computer put in place

  -F11: System Recovery

  -My BIOS is inheritance according to my request for information system.

  -J' have an Intel Core i5-3570, clocked at 3.4 GHz

  My questions are:

  1 should. what course of action I take to access MY BIOS to activate Intel VT - x? See the following image.

  2. I plan to the system through the Legacy BIOS mode BIOS flashing.  Am I wrong?  Yes.

  3. is there another way to activate Intel VT - x without access to the BIOS? No.

  If anyone can help I will be greatly appreciated. Thank you!

  

• Could not load the BIOS after RAM upgrade - Satellite A200

  Hello

  I've updated my RAM memory on my laptop Thishiba Satellite A200 (from 2 GB to 4 GB) but unfortunately now I can't enter the BIOS. Automatically load the operating system (windows 7 64 bit).

  How can I solve my problem?

  P.S. The new RAM works perfectly and it is recognized by Windows 7.

  Post edited by: bennito

  I don't know what you've done and why this happens, but what you can do is to check if the quick start option is enabled.
  Open Toshiba Assist > optimize > HWSetup > priority Boot and check the startup speed option it.
  Remember that it is set to Normal.

  Please, check and send comments.