Computer with Vista unable to connect to the internet through two computers with Windows 7.

Similar Questions

• What happens if I am connected to the internet through two different sources or more?

  What happens if I am connected to the internet through two different sources or more?

  You get Internet from two sources. What did you expect to happen?

  This is not double the speed of anything...

• Unable to connect to the internet through WRT110

  Hello

  I can't connect to the internet through my WRT110. I am connected directly but my modem at this point shaw. My DHCP settings will not retain an IP address. I'm going to status on the router (192.168.1.1) and find all information, IP address, subnet mask, Gateway etc. Defautlt are set to 0.0.0.0. I click on the intellectual property of release, then renew the ip and that everything remains as 0.0.0.0.

  I tried to set my router to static mode and entering the information in bold to ipconfig below, but which does not either. I also tried to reset the router back to factory default and tried everything on again, without success.

  What I'm doing wrong here?

  IPConfig:

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : vc.shawcable.net
  Link-local IPv6 Address...: fe80::c056:e161:d17f:3 b 09% 11
     IPv4 address...: 70.79.143.236
  ... Subnet mask: 255.255.252.0.
  ... Default gateway. : 70.79.140.1.

  Tunnel adapter ISATAP.VC.shawcable.NET:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : vc.shawcable.net

  Card tunnel Local Area Connection * 11:

  The connection-specific DNS suffix. :
  IPv6 address: 2001:0:4137:9e50:3 c 46:300 d: b9b0:7013
  Link-local IPv6 Address...: d fe80::3c46:300: b9b0:7013% 13
  ... Default gateway. :

  Card adapt 6TO4 tunnel:

  The connection-specific DNS suffix. : vc.shawcable.net
  IPv6 address: 2002:464f:8fec:464f:8fec
  ... Default gateway. : 2002:c058:6301:c058:6301

  Decreed a second IP address of my modem and I could contact my ISP. My router works now after power off.

• Unable to connect to the internet after you have reinstalled Windows

  It came with Vista on it, but it is basically screwed up... There was no recovery disk... so I did a clean install with a XP disk... all right except that I can't get on the internet... In the OTHER DEVICES ethernet controller PCI device, PCI Modem, SM Bus controller, unknown device and video controller (VGA Compatible) are all highlighted with a yellow question mark... Try to find the driver with my son's computer, but everything I find says that there in an internet search... until this problem is fixed, I can't connect to internet... Help, please! Thank you!!

  Hi Dreman1970,

  ·         What is the brand and model of the computer?

  Of yellow exclamation, PCI Modem and other devices Ethernet controller describes the drivers necessary for the device are missing.

  I suggest you use another computer connected to the internet to find your manufacturer's Web site. Then you need to find the driver to download links for your computer model. Once you have downloaded the drivers, you can transfer them to your computer and install them. Once the drivers are installed, you will be able to connect to the internet.

  See the following article for more information on installing the drivers:

  How to manage devices in Windows XP

  http://support.Microsoft.com/kb/283658

   

  Let us know if that helps.

• Unable to connect to the internet through the wireless network

  original title: this computer does not have an installed and configured wireless network adapter

  Hello, about a week ago I just reformatted my Windows vista computer, and now I do not have a wireless network and I cannot connect to the internet, I use another computer to do this, and only the network card I have is Marvell Yukon 8888036 PCI - E Fast ethernet controller. Please help I really wanet to go on the intrnet. My computer is mobile intel r 945gm express chipset controller 0 microsoft corporation wddm

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > looking for Vista drivers newer network adapters/etc > download/install the.

  The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Troubleshoot network adapter problems to Microsoft link above.

  See you soon.

  Mick Murphy - Microsoft partner

• Unable to connect to the internet through guest account

  We cannot connect to the internet using the guest account. I suspect a security update or my mischievous adolescent son changed a setting. This just recentlty that happened (in the past 48 hours) HELPS... I spent over 2 hours trying to get it online. The journal of WMD works very well and I was able to create another account just to see, and it also connects very well. What is the problem and how can I fix it?  Thanks, Biggator

  You do not want to connect to the Internet by using the guest account because it is precarious. In fact, you won't use the guest at all account. The guest account is a special system account, not one for when you feel hospital. For some reason, it is disabled by default in Windows XP, Vista, Windows 7, Linux, Unix and OS X.

  On TechNet:

  "The guest account is intended for users who need temporary access to the system. However, if this account is activated, a security risk may exist because an unauthorized user could have anonymous access to the system through this account. »

  http://TechNet.Microsoft.com/en-us/library/bb418978 (TechNet.10) .aspx

  So if you have enabled comments, turn it off now and create a standard/Limited (Vista, Windows 7, XP Professional/XP Home) for your visitors. Call the new user account to something like "visitor".

  And since you mentioned a teenage son:

  Make sure that the computer is clean:
  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  MS - MVP - Elephant Boy computers - don't panic!

• Unable to connect to the internet through a host mac

  2 weeks ago, I wasn't able to get on the internet. Fact diagnostic the test on my laptop and it said I had no internet access.  The Mac host in our home is ok and can connect without any problems. I tried several things and that you still can't find the problem. Any suggestions?

  Hello

  1 have had any changes made on the computer before the show?

  2. do you get an error message? If Yes, what is the full and exact error message?

  Method 1:

  Check the link and try to run the troubleshooter to check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  Check the link and see if it helps:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know if it helps.

• Unable to connect to the Internet through a router can just connect by Modem

  Hi, I am a user of the Inspiron 1525 Labtop.

  My home use 2 desktops and 1 this labtop and 2 days ago, I changed my wireless router.

  2 desktop computers connect to router with wire and there is no problem to use internet. but my laptop

  could ' t connect to the internet with no wire or cable. So, I tried to connect the Modem directly and can connect

  Internet. Only my labtop cannot connect to internet through this router (desktops work well).

  So, first I thought of my lancard which might be too old, so could not provide this new router, but no way

  because the desktop is older than that.

  Now, I want to just connect to internet with wire or wireless, either. Please help me.

  Laptop: Inspiron 1525

  O / s: Microsoft XP proffesional

  Network card: Dell Wireless 1395 WLAN Mini Card, Marvell Yukon 88e8040 PCI-E Fast Ethernet Controller

  Modem: Conexant HDA D330 MDC V.92 Modem

  Router: Xtreme N D-Link DIR-655

  
  

• Unable to connect to the Internet through a Linksys router Vista Satellite L300

  Hello guys,.

  I hope someone can help me.

  I tried to configure connect wireless to the internet using my new laptop. I used the wizard to set up the connection and he found my linksys router and it binds with it very well. Then when he tries to test the internet connection, it will just say error. I have not had this problem before and I'm a bit confused. When I thrn try to access a web page, I just get "Page cannot be displayed". I have troubleshooted and tried to reset the router, cable modem and laptop with no luck.

  Please could someone help with this?

  Any help would be greatly appreciated.

  Thank you

  Chris

  Hello

  To my knowledge, the router first with the data from your ISP.

  If done correctly, you should be able to connect to internet via LAN cable.
  Did you check that first? Do this!

  So if you can properly connect to internet via LAN cable, I would recommend set up the WiFi network on the router.
  There is a will to put the SSID (name of the WLan) encryption settings, MAC address filtering, firewall, etc.

  If these settings have been configured correctly, then you could try to configure WLan settings on your laptop!

• Unable to connect to the internet through the router using Linksys N - USB

  network connection

  I have a Linksys G wireless router on my computer and a wireless adapter Linksys N - USB on my wife's computer. Wondering why she can't get on the internet via my router? Thank you

  Thanks for the response, took the computer to the PC Nerddss and they had all connected it in a few minutes. All right

• Unable to connect to the internet through hp5510 printer

  As the subject line says:

  It's a printer Photosmart 5510. It prints and scans perfectly and all four laptops I installed it, the hp update downloaded software.

  When I first set up the printer, I was able to access additional applications online. After about half an hour, I lost the internet connection through the printer.

  I had installed using the automatic ip address selector and he gave me an address of 169.254.xxx.xxx.

  I have re-configured manually with a 192.168.xxx.xxx and even if the printer was working well with the PC it still wouldn't connect with internet.

  I have reset to factory settings and automatically and manually configured without success. Also, I restarted my router and changed the wireless channels.

  I can not yet use the eprint service anddownload any apps.

  My son tried to use a proxy, but it still wouldn't connect.

  As I said... .it worked for a short time and then stopped.

  Is there any solution for this?

  Thanks for any answers

  Hello

  Please try to manually set the DNS addresses in the EWS page:

  From your web browser, go to the EWS by typing the IP address of the printer.

  Enter the network tab.

  Click Network

  Click on the network (IP) address

  Under the DNS address Configuration, select manual DNS server and provide the following parameters:

  Define DNS preferred as 8.8.8.8

  and the alternative e-mail address 8.8.4.4

  Click on apply and try to access the Web Serives again.

  If the connection still does not work, and that the configured proxy address, enter the Web Services tab.

  Click the Proxy settings.

  Uncheck the option button, make sure that any field is left blank and click on apply.

• Unable to connect to the internet through Firefox or Chrome, but Internet Explorer works fine - what's up?

  Ping-works - I can get to google - but both Chrome and Firefox will not - connect I can't even download the Mozilla or Google code to reinstall BUT Internet Explorer (which I don't like) works very well

  Any ideas - just started to happen yesterday after years of use of Firefox and Chrome - what has changed in the last 24 hours - I have reset the router and have not installed new software.

  concerning

  Scott

  You might already have encountered these items when you send your question, but just in case:

  • Firefox and other browsers cannot load websites
  • Firefox cannot load websites but other browsers may

• Unable to connect to the internet after the removal of important processes in the task bar

  I am not very tech-savvy then let me explain.

  I have a laptop Lenovo I recently bought in August 2014.  A friend suggested that I have download the free application "Open Office" in line, so I could open a school power point.  Open Office gave me a handful of viruses, which I managed to delete, then having served the system well, panic I accidentally opened the Task Manager and deleted a bunch of processes that are running.

  Now, I find that, although I am connected to WiFi, I can't open Internet.  I click on Firefox, but it shows that I am unable to connect to the Internet.

  I have Windows 8; an easy way I can solve this problem?

  Thank you.

  Original title: I accidentally turned off the program that allows my computer to connect to the Internet

  Hi Tunasushiroll,

  Thanks for posting your query in Microsoft Community.

  I imagine the inconvenience that you are experiencing and will certainly help you in the right direction to solve the problem.

  The problem can occur for various reasons, including incorrect TCP/IP settings configured, firewalls third of anti-virus programs blocking the connection, or due to bad the advanced sharing settings. So, I would suggest trying the following methods and check if you system is able to detect the wireless network.

  Method 1:

  Run the troubleshooter network first, and then test your Internet connection.

  Open the Network Troubleshooter by hitting on any fly in the Dashboard screen, quilting Search(or if you use a mouse, pointing to the top right of the screen, move the mouse down and then clicking search), entering the network troubleshooterin the search box, type, or by clicking settingsand then by typing or clicking on identify and fix network problems.

  If the problem persists, try the following method.

  Method 2:

  Second of all, please check if the WLAN service is started and set to automatic. If it is stopped, then I suggest you to start the service and set it to automatic.

  1. Press the Windows key + R, type services.msc in the Run dialog box and press ENTER.
  2. Select the Autoconfiguration WLAN service in the list and double-click it.
  3. Change the startup to Automatic type, then click Start to start the service.
  4. Click apply and then click OK.
  5. Restart the computer and verify if the network is detected. If this is not the case, go to method 3.

  Method 3:

  Reset the DNS and TCP/IP settings.

  1. Press the Windows key + X, click prompt (Admin).
  2. Please enter the following commands and press ENTER after each one.

     netsh int ip reset resetlog.txt
     netsh winsock reset
     ipconfig/registerdns
     ipconfig/flushdns
     ipconfig/release

  3. Restart the computer to check the issue.

  Check if the system is able to detect the network. If this is not the case, go to method 4.

  Method 4:
  Temporarily disable the security software (if any), and check if it helps.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Additional information:

  Windows wireless and wired network connection problems

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• Computer shows it's connected, but unable to connect to the Internet

  Original title: also connected but unable to connect

  I have a HP Pavilion a1710n 64 Dual Core Processor running Windows Vista Home Premium.

  The computer shows that I am connected to the internet, but I can't connect to IE or firefox.

  My Internet Protocol Version4(TCP/IPv4) properties shows that the two buttons marked for obtain an IP address automatically as well as the use the following DNS server address.

  My network card is NVIDIA 10/100/1000 Mbit / s, and the computer shows that it works correctly. I tried to do a back roller and re - put to date but still the two marked buttons.

  Large number of background information...

  I was trying to understand why the windows installer did not work on my son's account. I went in systems and changed to start and automatic manual. Rebooted PC and the firewall do not come. Tried to do a restore, but failed and lost all my restore points.

  At this point, I lost my internet connection to know after vainly trying to figure out the problem I contacted an ATT(my internet server) of things ATT me had to do was change the properties to get the use of a DNS server address automatically and had typing me the address. After reviewing the many things ATT concluded there was not a problem with my connection and the PC is configured correctly and suggested that I should speak to technical support and of course, it was not free.

  Tech support determined there was something that crashes me to connect to the internet and had run me malwarebytes. He detected 24 traces of adware and 2 traces of a virus in the registry database. I deleted everything and still no connection to the internet. Next Tech had me run Combofix and says everything should run fine after that. Still no connection to know Tech # 3 had executed me guests of orders with ping commands. Finally, he had me check the auto config button and that's where I discovered the two buttons were lit. Tech said "can't be." Well it is. That's when I tried to roll back the driver, but no luck so tech says only option is to restore the whole system.

  GRRRR... After several internet searches that I'm about to do except nothings saved and whenever I try to use my backup and restore fails.

  Any help would be appreciated. I'm still fairly new to PCs so please be patient with me. Laughing out loud

  I know that my options have been counted, I was able to save what was important and made a full system recovery. I am happy to say that I'm back on the internet.

  Thank you very much for your help and support. I learned a lot on my computer, as well in location wonderful are the microsoft forums :)

• Vista PC is offline, unable to connect to the Internet by LAN or wireless.

  Original title: Vista (Japanese OS)

  My Vista pc is offline (unable to connect to the internet), how install and run the Fixit tool?

  I have read that the English, however, my pc is in Japanese. I can't connect to the Internet by LAN or wireless.
  How can I get the Fixit tool to work on the said pc?
  Help, please!

  Hello

  1. what Fixit tool you try to run?

  2. what exactly happens when you try to connect to the Internet? You receive messages or error codes?

  You can read the following article and check if it helps:

  Windows wireless and wired network connection problems

  You can also read the following article to change the display language:

  Change the display language

  You can use another computer to download the Fix from Microsoft, then use portable storage such as a USB drive, CD, DVD, etc., to carry the Microsoft fix it on your computer.