Unable to connect to the internet through the router using Linksys N - USB

Similar Questions

• EA6500 unable to connect to the router after Time Machine

  Just got an EA6500 - updated to the latest firmware available.

  I have attached 2 x WD NAS and 1 x WD through the USB port of the device.

  Each time after I finished running Time Machine on the MacBookPro (written to one of the WD NAS), I can no more connection to the router as neither the local IP, or the cisco connect cloud. The error message I get (loosely formulated) is: unable to connect to the router. Please ensure that the router is connected to the internet.

  At this point, all the devices connected to the router (wired and wireless) still can access Internet perfectly. Only the console of the router is therefore more accessible.

  Anyone else have the issue?

  Any ideas on how to solve it?

  Contact support for Cisco and the person advised me to do a factory reset (even if the router is new with no customization!). Regardless, it now works correctly. Cisco Cloud Connect works always before, during, and after a Time Machine.

  "When in doubt, try to turn the grid and the.

• Unable to connect to the Administration of Linksys to my WRT54G v.6 page

  Hello

  Recently, I moved into a new House and brought my old router with me.  I set up this router to my former place long ago, but when I hooked it up here, I am unable to connect to the Admin of Linksys page (http://192.168.1.1 for example).  I think that I changed the router what IP to 192.168.1.101... it was a long time ago so I don't remember exactly.  I tried find what it was by typing "ipconfig" in the command prompt and using the address "Default gateway" IP address as the address of router, but that has not worked.

  I tried to reset the router to factory default settings by pressing the button of reset for 30 seconds, then connect to http://192.168.1.1 but it does not help.  When I release the reset button, just power light continues to blink rapidly until I unplug the router.

  I can access the internet without any problem, but I noticed that I connect my router differently than the instructions provided here.  I connect an ethernet cable from my modem to 1 of the 4 ports on the router (just like my laptop) rather than the port of 'internet' on the back.  Don't know if that is related or not, or even what is the cause.

  I use Windows Vista on my laptop if it makes a difference.

  Thanks in advance for your help,

  Ryan

  The modem must be connected to the internet port of the router and the conputer on one of the 4 ports on the router... Now, check if you are able to ping the default gateway of the router. If you get 4 answers then, make broser on the computer settings... Open an IE, click Tools > Internet Options, then click on delete and delete all the files, cookies, history, forms... GoTo 'Connections', make sure that never Dial a connection is selected, click on network settings and make sure that all the options are unchecked... Once you are finished, click OK... Close IE and reopen...

  Now, try to open the linksys configuration page by typing 192.168.1.1 in the address bar. You can also try another computer.

• Printer Hp6700: unable to connect to the router wireless D - Link DI-514 when SSID Broadcast is set to no.

  HP6700 printer: unable to connect to the router wireless D - Link DI-514 when the router Broadcast SSID is set to no. My MAC laptop and HP laptop both work with the set SSID on no. If I change the router Wireless SSID Broadcast is YES, then the printer HP6700 can connect to the wireless router. I set up the printer it saying that the SSID and password have been, the same as both of my laptops, but it connects ever, unless I have change the router to broadcast the SSID. Help!

  Have you tried to update the firmware on the DI-514?

  You can also try to set a static IP address on the printer, and then assign the printer to the list of DHCP static in the interface of the router.
  To give a static IP address to your printer:
  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.
  Now, stop the router and printer, start the router, wait, and then start printing.

  After that you remove and re - add the printer to your Mac.

  Show support by clicking on the blue Kudos star in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• RCU error: unable to connect to the database using the contact information provided

  Hello

  I am not able to connect to the database using the remote control 11.1.1.10.1 to create patterns. I ran the UCR even a week ago and I managed to connect. My database and listener are up and running and the host and the credentials are correct. I don't know where is the problem. Any help will be appreciated. Attaching the screenshot for reference.

  

  Concerning

  Oumaima

  Hi Handal

  Thanks for the reply. Looks like someone had blocked the firewall settings, so I was unable to connect to the database using the port.

  Thank you

  Oumaima

• Unable to connect to the router

  -Please ignore this message: I did not wait enough to do the factory reset. It seems that launch a factory reset without waiting for 10 seconds only restarts the router.

  Hello

  Today I tried to connect to my router (I do not use it for a few years) and it didn't work at all.

  Initially, I plugged it in just 2 RJ45 cables: one for internet, one for the PC. The computer could not connect to the router (DHCP failed).

  I then restored the factory settings and tried again: same thing, the computer could not find the router via DHCP.

  I tried to force an IP address (IP: 192.168.1.5, mask: 255.255.255.0 Gateway: 192.168.1.1).

  By forcing the INVESTIGATION period, I was able to connect to the router, but when I tried connect to 192.168.1.1 with admin/password, it wouldn't let me (bad password - don't forget I restored it to factory settings, several times actually). The address http://routeurlogin.net/ is not found (404) and I was unable to go on websites (404). A curious thing is, using this connection, I was able to connect to Skype (and send/receive messages), although the sites Web could not be reached from a browser.

  I'm running out of ideas to solve the problem, but I suspect a hardware problem, so any help would be welcome.

  Yes he did.

  I couldn't find an option to delete my message, otherwise I would have done it.

• Unable to connect to the router (even after reset)

  I'm really frustrated, and I hope that this community can provide an answer. After all the hype around this router, it is he who gave me the most trouble.

  About a month and a half... completely randomly it seems to me, I could not connect to the router more. Not through intellectual property, routerlogin.net/com...nothing. It just says: cannot display the page. I did everything I could possibly think, tried all of the suggestions I could find here and elsewhere and still nothing would work.

  I finally did a hard reset and obviously lost all my settings... and RIGHT AFTER the hard reset after upgrading the firmware, I can't connect to the router again. This could be the cause? Is there a way around it?

  The router worked fine until about a month and half ago. Then I stopped being able to connect to the admin page. Several resets hard did nothing.

  I ended up RMA'ing it and the new replacement works fine (for now).

• Unable to connect to the router WLan - Satellite L300D

  Please help me so that I have still a few hairs left!

  I installed WLAN driver on my laptop Satellite L300D with Vista Home installed.

  I see my network in the available connections, but when I go to connect, it will not connect.

  My other two desktop computers can connect to the router without a problem.

  Any suggestions?

  Thank you
  Neil

  Hello

  I think that you didn t try updates. Right?
  Therefore, my first recommendation would be an update of the BIOS and driver WLan.

  Check the current version of the BIOS that is available on your laptop. If the latest version has been released then update the BIOS.
  In addition, to download the latest WLan driver from the Toshiba WLan portal and to update:
  http://APS2.toshiba-tro.de/WLAN/

  On this Wlan site, you will find three different WLan drivers for three types of WLan cards. First check your wireless network card, and then use the right driver!

  See you soon

• Unable to connect to the router (BEFSR41 V4.0)

  I have a Linksys BEFSR41 (Version 4.0) wired router and I am not able to connect to it. It has been in storage (the top of a closet shelf) for the past two years and when it when it was still used it worked like a pro.

  I used the downloaded from the site Web of Linksys router configuration utility to install it, and when it gets to the final stage, he says that it cannot connect to the router. Try to go to 192.168.1.1 translates into a (very long) network timeout.

  I have reset the router several times (retained in the for more than 10 seconds reset button) and have had no result. All the lights on the front of the router work normally.

  I already checked and I'm set up to get the IP addresses of network automatically rather than assigning a static.

  Any help appreciated,
  ~ Darxide

  Number set by putting the ADSL modem in bridged Ethernet mode.

• Satellite A500 - 03P: unable to connect to the WLan using Win 7 + event message

  Hi all

  I recently bought the Satellite A500 with the offer included Windows7 while he was available late October 09.

  So I had the Toshibe DVD for the upgrade and followed the steps and Visa home premium upgrade to Windows 7. Now I have two questions.

  (1) I get a system event Notification after start, talk to me about the system event log. The full message is below.

  Unable to connect to a windows service
  Windows could not connect to the System Event Notification service. This problem prevents limited users to logon to the system. As an administrator, you can view the system event log to see why the service failed

  (2) I was able to use this laptop for the internet before the upgrade, both via a USB wireless drive as well to the office via a DSL modem.
  Now I can't access the internet after the upgarde of Windows 7!

  For example the Optus dial-up box pop up appears commandeLorsque I click on 'connect', it does not connect.

  Can anyone help please?

  Thank you
  C I

  Hey Buddy,

  (1) did you check the Configuration of the Service for this service? The Boot System Event Notification Service type must always be set to automatic. This service is absolutely necessary for Windows and shouldn't t be disabled or set to manual startup type.
  Check it!

  (2) to be honest I never heard on the internet BEFORE, but normally, it should also be possible to access the Internet with Windows 7.
  Make sure that the WLAN or LAN card is installed properly and check the TCP/IP settings. If you are missing some driver you can get on the page of Toshiba.

• Unable to connect to the router with windows 7?

  I have just bought an Acer Revo R3700 and installed Windows 7 above, but I can't connect to my router.

  My router is heaven and successfully has 4 laptops (both under Vista, two 7 running), an Xbox and a Wii and two smartphones connected to him. Yet I just can't do this system to connect to him.

  I'm at my wits end... I've tried absolutely everything. I searched the Microsoft answers site found several similar problems and tried a lot of solutions, including adding files in the registry and update drivers.

  At first I could connect to the internet every now and then, but it was biblically slow (I tried to download Google Chrome and got him to 0.2 Kbps) and soon disconnected. Now I can't connect at all.

  I just downloaded a the Ethernet controller driver and updated a driver WLAN as they apparently do not come with Windows, but it still doesn't work. Although the message has now changed to "Unable to connect" to "Limited connectivity" (even though I think it's more coincidence than anything else)

  It should not be a question of signal strength, like the Xbox and laptop computers work fine when placed next to her.

  Really needed a solution to what running an ethernet cable is not really an option :(

  Thanks in advance guys. I'll be happy to provide any additional details if you need it :-)

  EDIT: / / I would add that I seem to be able to connect fine with a phone as a hotspot? It is very very weird.

  EDIT: / / I just managed to connect, but its very slow and not changed anything for the last 100 times? Everything seems to be completely random when it let me? : S

  Hardware support comes equipment - including the drivers/software manufacturers to use such software in all operating systems.

  Looks like a possibly faulty hardware or shotty (the wireless network device.  Make and model)?

• Portege 2010 PP201E - unable to connect to the router encrypted with WPA

  Hello

  I just bought a Toshiba (? 2002) Portégé 2010: PIII 866 MHz/XP... Part number: PP201E-00GPP-EN. support for the Wi - fi network: 802. 11 b

  When I try to connect to the internet using my sky router (WPA / PSK) my Toshiba does not connect because it asks for the WEP.
  I tried to change it on Assistant, but that's it or turn it off.

  I have only one option is to change the router WEP, but I heard it is an old and easily hackable, technology
  In any case, I don't want to mess with my router, another PC wireless and my playstation.
  I looked on update of the driver toshiba but that did not work.

  Does anyone know if there is a updated for my lapptop driver or do I have to buy a USB product?

  Thanking you

  Hello

  Maybe the internal WLan card does not support the newer WPA encryption but only the WEP key.

  The fact is that encryption is hardware related. This means that an update of the driver will not help you. If the hardware does not support WPA, then you need to replace the WLan card or buy a USB WiFi dongle that supports WPA.

  I have thin external USB WLAN key is the easiest solution

• Satellite A300D - unable to connect to the router

  I can't connect to my wireless modem that works correctly for other laptops at home.

  I bought this phone 2 weeks ago and when I discovered that it can not connect, I took it to the shop, I bought it. Here, surprisingly it connected to wireless internet so they told me that there must be sth wrong with my modem. I reinstalled my modem but still not good. I can connect with other laptops that have vista as well.

  I can view the connections. Sometimes, he tells me that the password is wrong that I'm sure I get right! I even tried to completely disable password security, then it seemed like it was connected, but I could not access Web sites, including google.com. Sometimes it is said that id verification timeout. I reinstalled the wireless driver that did not work. He has no problem with the connection to the local network. I almost tried everything but still can't connect.

  Help, please!

  Hello

  Why you try to reinstall the modem driver if you have a problem with your wireless network card?

  Anyway, if you can plug it into the router in the shop everything should set up and installed correctly on your laptop and the reason must be the router.

  So in your case, I would try to update the firmware on your router.
  If you use DHCP, try static IP addresses. Try to also disable filtering of MAC addresses and try another encryption, e. g. WPA2.

• ea4500 unable to connect to the router smartwifi

  Since yesterday my linksys smartwifi account says that it cannot connect to my ea4500.

  I pedaled power the router itself and it is not fixed.

  The router has access to the internet. I can also access the router locally using 192.168.1.1

  Is there a setting somewhere in the router UI that will allow me to sign out and back in on the account of smartwifi?

  Linksys system has been up and dow lately so it's most likely the problem. Sometimes its down for days at a time. Very unreliable. Give him one day and see if it comes back. Can the mods can follow it and put it on a sticky?

• Error in the configuration wizard. Unable to connect to the router.

  All connections are correct.  I am able to connect to IE and FireFox with ethernet and connected my corner via "Linksys".  I opened with ISP address and configure security.  Is there more in the configuration I have to do?

  What is the model number of your router? If the internet connection is working well, then you need not to worry the installation disc. As long as you know how to set up the router manually and able to access the interface of the router then there is nothing to worry about. It is with the disk configuration wizard is exceeded or there could be some firewall software on the computer that is blocking the setup of your router to detect Wizard. It is the most common problem I encountered, but well it's always the manual configuration. If you do not need to install and use the software just go to the linksys download site, or you can also consider using another computer.