Computer won't startup, startup repair doesn't work & stuck in loading programs, safe mode please wait.

Similar Questions

• Vista used to start, tried restore, recovery, startup repair doesn't solve anything

  Since about three weeks ago, I got serious starting problems. I restarted my computer and after the first HP screen where it usually starts loading windows, it went to a black screen. I turned my computer restarted offand and he did it again and again until finally he did something different, he went to the Startup Repair which I had never seen before. After doing this it says restart, I clicked on it and went back to the black screen. So finally I just decided to make a full recovery.  After the recovery of the first time, he did the same thing with the black screen. He went to the Startup Repair, but this time has given me the ability to send or not to send so I went to advanced options where I could retrieve, drive recovery, restoration, command prompt, test for diagnosis of memory, etc.. I chose the memory diagnostic test. It restarted after about 45 minutes and it worked. I was restarted for about a week. Then again of course in the beginning. I tried pressing F10 and go to the BIOS where I did a test of memory and a hard drive that has failed. I tried a recovery once again, and it's the same thing. Now, it takes about 10 times to begin to get the Startup Repair go. Pressing F11 to retrieve said Windows loading files as it usually does, but then won't go to the repair screen, it goes to the black screen. One thing that seemed similar in all cases, it is that I installed Service Pack 2. Im not sure if this is the reason. I also did some research and a ton of people have this same problem only about a year and a half after the purchase of their computer. I think it's ridiculous. Many people have had this problem when Windows Update arrives, and the last time this happened when Windows Update has occurred.  Something is not seriously and I have no idea how to solve this problem.  Microsoft should give Windows 7 for free to all buyers of Vista that are very disappointed with it.

  Do you know when this problem started?  Try a system restore to a point in time before the problem started (if you've already tried this, skip this part).  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.

  If the system restore does not work, do a startup repair (I know you tried, but try again) to boot from the Installation of Windows Vista genuine disc (or one you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not work, try to start in safe mode (repeatedly hit F8 key so that the start and go in safe mode with networking) or use command from the disk.  Then we will check some of your system files:

  Go to start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator (ignore it's using the disc).

  Type sfc/scannow, go and let it run.  It will scan and try to correct some of your system files.  If all goes well, it is completed with no corruption that he couldn't fix (if such try to analyze it to find the problem or files using http://support.microsoft.com/kb/928228 or corruption several post here and post the results back here.)

  While in the command prompt, type chkdsk /f /r and enter and let it run.  It will scan and try to solve any corruption or bad sectors on your hard drive and remove especially as a cause.

  If this does not work, you will need to do a repair/system upgrade using the Windows Vista Installation disc authentic (you own or that you can borrow from someone).  Here is the procedure: http://www.vistax64.com/tutorials/88236-repair-install-vista.html as well as the upgrade from an earlier version of the Windows section of the following: http://support.microsoft.com/kb/918884.  Although this will not affect your data, settings or programs, you should always back up your data before you start just be on the safe side. If other procedures do not work, it is almost certain to work.  You can have a lot of updates to re - install (including all you need to remove service packs).  If the version on system with SP1 or SP2 preinstalled cane and the disc is an earlier version, then you will need to do a slipstream drive as follows: http://www.vistax64.com/tutorials/151606-vista-sp1-slipstream-installation-dvd.html.  Chances are good that you won't be able to do this if you cannot boot normally into the system.

  If this does not work, I'm aftraid the only option is a clean install.  You can use Knoppix http://www.knopper.net/knoppix/index-en.html with a good ISO as Copier: http://isorecorder.alexfeinman.com/isorecorder.htm as well as a blank CD.  This should give you enough access to the system (if you do not have any other means) to backup your important data.  Once this is done, you can do a clean install or by using the Installation of Windows Vista genuine disc or the recovery disk with the recovery Partition (whatever the process is dictated by your computer manufacturer).  Do a clean install follow these steps: http://www.winsupersite.com/showcase/winvista_install_03.asp (taking into account the necessary adaptations by the procedures of the manufacturer of your computer).  Then you will need to re - install all your programs, reset all preferences, reconfigure your network settings and e-mail, restore your backup of the data, run Windows Update with possibly close to 100 updates pending...

  I hope one of these procedures can solve your problem - if not, then it is probably some sort of hardware problem. Return message anyway so we know how it turns out.

  Good luck!

  Lorien - a - MCSE/MCSA/network + / A +.

• during the installation of Vista Service Pack 2, the computor has been disconnected. Now, I don't have an operating system and startup repair does not work. What should I do now?

  Computor was disconnected during the installation of Vista Service Pack 2. I did now no operating system and startup repair does not work. What should I do now?

  You may have to reinstall Vista from the original media or from the recovery partition according to the type of computer you have.

  Hope that you made the backup recommended all of your data before attempting to install Vista SP2.

• Vista starts, the Startup Repair tool works for hours, even in Safe Mode

  In the course of the night, desktop went south.  Screen showing the morning ran Srartup repair.  Ran for hours with no result.  Stop computer and started several times, same thing.  Stop down and when started again, got in the Mode without failure.  He went into the Startup Repair again, ran for hours yet. no results.   Help, please.

  Hello

  You may have a faulty hard drive. I suggest to download and run a diagnostic tool of disc from the manufacturer of the computer or the hard drive manufacturer. Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Launch Startup Repair does not work

  Hi, the 'Launch Startup Repair' option does nothing for my installation of Windows 7 64-bit edition.  If I select the screen simply refreshes and presents me with the same two options - Launch Startup Repair and start Windows normally.  It's as if something prevents me to attempt any repair solution.  Anyway, which would cause Launch Startup Repair does not have to work.  Thanks if someone can advise.

  Hi, the 'Launch Startup Repair' option does nothing for my installation of Windows 7 64-bit edition.  If I select the screen simply refreshes and presents me with the same two options - Launch Startup Repair and start Windows normally.  It's as if something prevents me to attempt any repair solution.  Anyway, which would cause the launch startup repair does not work.  Thanks if someone can advise.

  Hello

  It may be damaged.

  If you have problems with the use of the built-in repair software:

  Make your own information system repair disc in this tutorial:

  "How to create a Windows 7 system repair disc"

  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  "This will show you how to create a system repair disc Windows 7 to be able to use to start the system recovery options to help recover your Windows 7 installation, if you have not a Windows installation disk, can't find your Windows installation disc or can not access the recovery options provided by your computer manufacturer.

  A system repair disc is not able to install Windows 7.

  Note

  If you are unable to start your Windows 7 to create a Windows 7 system repair disc, and then you could create on another computer for use on your computer. »

  _____________________________________

  Then, use this disk for System Recovery Options:

  "System recovery options".

  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  "How to run a startup repair in Windows 7"

  http://www.SevenForums.com/tutorials/681-startup-repair.html

  See you soon.

• Computer turns on but does not boot to Windows, startup repair does not work

  When I turn on my laptop, it brings me to a screen titled "Windows Error Recovery" which means the following:

  "Windows did not start.  A recent hardware or software change might be the cause. »

  He asks me if I want to '(recommended) launch Startup Repair' or 'Start Windows normally'.

  When I select repair system, the screen turns off for half a second only and brings back me to the exact page as I was already on.

  When I select "Start Windows normally", he brings me to the loading screen that usually starts with Vista (anyone who says (c) Microsoft Corporation), except that it never stops loading.  I left for hours, and he was still on the same screen.

  I have a laptop Dell Inspiron 1525 with a processor Intel Core 2 Duo and Windows Vista Basic.

  Follow these steps to try to solve your problems of boot.

   

   

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Dell recovery options:

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  Above is Dell to reinstall Vista from the DVD on your computer.

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

  And that way if you have a recovery partition on your hard drive.

  See you soon

  Mick Murphy - Microsoft partner

• Computer freezing and startup repair does not solve the problem.

  fix my computer when windows start dump then launch startup, but does not solve the problem. Can you help me solve the problem

  Hi Wwiese,

  Thanks for posting your query in Microsoft Community.

  I understand from the description of the problem, the computer freezes in the commissioning on the Windows 7 computer.

  I would appreciate if you can help me with the following information.

  1 were there any hardware or software changes made on the computer before this problem?

  2. are you able to boot into office?

  3. you receive an error message/code?

  I suggest you try these methods and check if it helps.

  Method 1

  Disconnect all external devices (printers, scanner, USB (universal serial bus) drives, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue. Then download drivers software updated for this particular device.

  Method 2

  Try to start in last good known Configuration and see if you can start very well.

  Using the last good known Configuration

  http://Windows.Microsoft.com/is-is/Windows7/using-last-known-good-configuration

  Method 3

  Start the computer in safe mode and check if the problem persists, if the question does not persist then perform the clean boot and check if the problem resolves.

  Step 1

  Safe mode starts Windows with a limited set of files and drivers. Startup programs do not work in safe mode, and only the basic drivers needed to start Windows are installed. Please click the below mentioned link.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  http://support.Microsoft.com/kb/929135

  Note: After completing the steps in the clean boot troubleshooting, follow step 3 from the link to start the computer to a Normal startupmode.

  Method 4

  If the problem persists, I suggest you perform a startup repair and check if it makes a difference.

  Startup Repair: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  What are the system recovery options in Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  In addition, you can do a System Restore the Windows Recovery Console.

  It will be useful.

  Let us know if you encounter problems with Windows in the future. We will be happy to help you.

• Computer won't startup connection step and keeps restarting

  Wednesday, my brother came downstairs and said that his computer crashed while he was on the internet, (dirty Web sites, I think) and when he trys and in turn, it leaves him open a session.

  So I went to take a look, since I understand computers more than anyone in my family and the computer kept restarting itself at the stage of the connection after 4 seconds to be on it. I wentwww.ijinni.com and asked advice there and they said to try to access the computer through network in safe mode, but I don't have the chance of the night here.

  Tonight, I finally got a chance to try to do, and when I try and access the computer through network in safe mode, another page appears saying

  Please select the operating system to start:

  Microsoft Windows XP Professional

  I chose it because it is the only one available and is the system that the computer is running on, however, after having done that, the computer goes through the same processes similar to load upwards. for example dell loading screen, screen loading windows xp, and then you connect to the stadium. When he arrived at the stage of connection, the computer restarted itself once again, which means that I can not even access the computer through safe mode.

  PLEASE CAN YOU TELL WHAT CAN I DO TO SOLVE THIS PROBLEM, AND WHAT IS THE PROBLEM!

  Bug Check Code 0 x 44 http://msdn.microsoft.com/en-us/library/ff558982(v=VS.85).aspx

  Download and install Malwarebyes (free version for individuals only), updated definitions and run in safe mode. Disable other security software while you do the analyses.

  http://www.Malwarebytes.org/

  Hope this helps, Gerry Cornell

• the computer restarts on startup and then only works in safe mode

  I'm running out of options.

  I have a MSI all in one pc which runs on windows vista Basic. I turn on my computer and it will show my lock screen, but just before I can type my password, it restarts itself and give me different options of safe mode. I tried a lot of different solutions, but none of them seem to work. Can anyone help me, please.

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode (which you already know)

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If it doesn't, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  See you soon.

• Satellite A300 - startup repair does not work

  When I went to use the Startup Repair option in the advanced boot options at startup that he told me that the application cannot run and shut down the computer.

  I have a laptop Satellite A300-1OM.

  As far as I know, this option has nothing to do with Toshiba and this is the Microsoft function.

  What is the problem with your A300?

• Startup Repair does not work it starts when it wants... .and when it does not I must start up for hours before his sucsessfull...

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 1033

  More information about the problem:

  BCCode:                                               a

  BCP1: 000000000000002A

  BCP2: 000000000000000C

  BCP3: 0000000000000000

  BCP4: FFFFF80001EB5D17

  OS version: 6_0_6002

  Service Pack: 2_0

  Product:                                               768_1

  Files helping to describe the problem:

  C:\Windows\Minidump\Mini012210-02.dmp

  C:\Users\Deb\AppData\Local\Temp\WER-100698-0.SysData.XML

  C:\Users\Deb\AppData\Local\Temp\WER9F0C.tmp.version.txt

  Hello

  Added new hardware, updated drivers to date (don't forget to check in Control Panel - Windows Updates - pilot
  updates), or add key software lately? Pilots and security/antivirus/antispyware products are also likely
  suspects. Next message is my generic driver updated methods to use when you get to this section of the
  troubleshooter.

  BCCode: a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the Windows Advanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  It is my generic troubleshooting tool and can probably give more specific help when you give the ICC codes.

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• MY COMPUTER DOES NOT START, NOT EVEN WHEN YOU TRY TO PUT IT IN SAFE MODE, EVERYTHING GOES TO A BLACK SCREEN, PLEASE HELP ME!

  OK, so last night, my computer was freezing up so I held the power button down to turn off, I turned it back and he asks me if I want to start in safe or just normally.  I chose because it starts as usual, it's just sitting there, it goes through the motions as it will start but it never does, I went to sleep woke up to the top and all I have is a black screen with mouse pointer again, nothing has changed, the same things happen when I try to start it in safe mode.  I tried to get the disks it is came up with, but the computer seems to not even acknowledge that they were never inserted, I don't know what to do, can anyone help me, I'm sitting here on the laptop of my bf and I am interested in this black screen with the pointer of the mouse in the Middle, I don't know what to do...

  Hello

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you don't have the disks your
  system manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (making the system restore it)
  must be bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation
  (if all goes well, the data records and need to reinstall programs). Be sure to do a good backup or three.

  You can use another DVD that aren't copy protected but you you need to own
  Product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (a line type or copy and paste one line at a time and hit enter - enter a bracket)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)

  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Difficult virus that won't let me turn off the coast of the restoration of the system, use regidit, blocks the pc in safe mode (please help)

  I think that this virus - the main I think is trojan. BHO-keep coming back on my computer using System Restore.  Panel crashes every time I try to disable the system restore.  It crashes whenever I try to do anything in safe mode.  As mentioned, I can't get rid of it in the registry as it won't let me.  I have Microsoft Security databases, which doesn't quite work.  I have temp got rid of it with malwarebytes, more than once, but this virus so that perhaps others stay on my pc. I have Vista.

  I tried several analyzers and I don't know what to do if it won't let me get rid of it manually.  Also, he won't let not use my sidebar.  When I click on it anywhere it just makes a noise.  Could someone please help?  I'd be happy.

  If the suggestion above does not resolve the problem, then you might do well to deny a free online help to rid your computer of malware.  Try one of the following online forums that specialize in resolving these issues.

  Malware removal Forum

  Safer-Networking Forum

  What is the Tech Forum

• ' ' MUST BE ANSWERED ON ' HOW TO PUT THE COMPUTER IN SAFE MODE "PLEASE

  I HAVE A COMPUTER THAT I NEED TO PUT IN 'SAFE MODE' QUESTION WHAT SHOULD I DO TO PUT IN SAFE MODE?
  I TRY WITH MY KEY "F8", BUT THAT DOES NOT HELP.IS IT ANOTHER WAY THAT THIS IS POSSIBLE?
  PLEASE SEND ME E-MAIL ON THIS ISSUE PLEASE... MY COMPUTER IS DOWN. NEED HELP?
  E-MAIL ADDRESS IS
    E-mail address is removed from the privacy *.
  Thank you...

  Turn on the computer.

  Start typing the F8 key. The Windows Advanced Options Menu appears. If you start to press the F8 key too soon, some computers display a "keyboard error" message or if too late continues start. To resolve this issue, restart the computer and try again.

  Check that the safe mode option is selected.

  Press ENTER. The computer then begins to start in safe mode.

• the mouse disappears at the level of the office. F8 doesn't let me do it in safe mode

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem
  • restarted several times without success

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  krdav4446,
  We could use a little more information on this issue.  What version of XP and service pack are you running?  If something has changed on your system recently (hardware or software)?  Have you tried another mouse?  What happens when you try to start safe mode?  Do you get any error messages?

  Here are some delicious dishes.

  If the mouse is USB, try another port (do not pass through a USB hub).

  If the mouse is wireless, replace the batteries.

  Unplug all external devices (printers, USB hubs, USB keys, etc...).

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.