Configuration for FWSM Guide

Similar Questions

• Cisco RV220W IPSec VPN problem Local configuration for any config mode

  Dear all,

  I need help, I am currently evaluating RV220W for VPN usage but I'm stuck with the config somehow, it seems that there is a problem with the Mode-Config?

  What needs to be changed or where is my fault?

  I have installed IPSec according to the RV220W Administrator's Guide. Client's Mac with Mac Cisco IPSec VPN, I also tried NCP Secure Client.

  I have 3 other sites where the config on my Mac works fine, but the Cisco VPN router is not.

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: remote for found identifier "remote.com" configuration

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: application received for the negotiation of the new phase 1: x.x.x.x [500]<=>2.206.0.67 [53056]

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: early aggressive mode.

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: RFC 3947

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received unknown Vendor ID

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsec-nat-t-ike-02

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: CISCO - UNITY

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: received Vendor ID: DPD

  2013-03-07 01:55:49: [CiscoFirewall] [IKE] INFO: for 2.206.0.67 [53056], version selected NAT - T: RFC 39472013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: floating ports NAT - t with peer 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload is x.x.x.x [4500]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT - D payload does not match for 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: NAT detected: Peer is behind a NAT device

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: request sending Xauth for 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association established for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REPLY" from 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: connection for the user "Testuser".

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] INFO: type of the attribute "ISAKMP_CFG_REQUEST" from 2.206.0.67 [52149]

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: ignored attribute 5

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28678

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] ERROR: local configuration for 2.206.0.67 [52149] has no config mode

  2013-03-07 01:55:50: [CiscoFirewall] [IKE] WARNING: attribute ignored 28683

  2013-03-07 01:56:07: [CiscoFirewall] [IKE] INFO: purged-with proto_id = ISAKMP and spi = 1369a43b6dda8a7d:fd874108e09e207e ISAKMP Security Association.

  2013-03-07 01:56:08: [CiscoFirewall] [IKE] INFO: ISAKMP Security Association deleted for x.x.x.x [4500] - 2.206.0.67 [52149] with spi: 1369a43b6dda8a7d:fd874108e09e207e

  Hi Mike, the built-in client for MAC does not work with the RV220W. The reason is, the MAC IPSec client is the same as the Cisco VPN 5.x client.

  The reason that this is important is that the 5.x client work that on certain small business products include the SRP500 and SA500 series.

  I would recommend that you search by using a client VPN as Greenbow or IPSecuritas.

  -Tom
  Please mark replied messages useful

• who can help me with "insufficient resources to meet the level of failover configured for vSphere HA.

  Hello world

  We tried to gif a 14GB of ram and make server complete a booking for her.
  This is a server for the exams and the vendor told us to do.

  I can't any more then 5500MB reservation on it, when I anymore that I get
  "Insufficient resources to meet the level of failover configured for vSphere HA.

  We have:

  2 X 5.1 ESXi hosts
  Each host has
  2 x processors (8 Cores each) with HT active.
  255,75 GB of Ram

  vSphere HA has been activated.
  Admission control policy is enabled and that the ability to failover is 1 host.

  What is the problem here?

  Thank you
  Ernst.

  
  

  Admission control policy is all about to give you the kind of guarantee that if the host failure happens then there will be enough resources to perform the successful failover.

  in simple terms, it comes to reserve the resources of failover.

  I would recommend going through the notion of vSphere HA, reduced control policy the following document.

  https://pubs.VMware.com/vSphere-60/topic/com.VMware.ICbase/PDF/vSphere-ESXi-vCenter-Server-60-availability-Guide.PDF

  From the Page number 22, the details that you need to study is given. Focus especially on part calculations Slot size of it.

  in your case you HA vSphere with number of failure of host to tolerate as admission control strategy defined.

  This means system will calculate CPU and memory slots out of the resources in your cluster, and the total number of units, it will keep some resources like reserved for failover, and others will be available to be used. It all depends on how much failure of hosts that you want to tolerate.

  now in your case, if you try to increase booking one of the virtual machine, which will then affect the number of locations in your environment, and so reserved ability to failover is violated, the system will not let you do what you want to do. As the energy on a virtual machine, or growing booking a powered VM etc..

  If you find that you have enough resources in your cluster and due to some virtual machines with very large cpu or memory reservation, number of places is less than you can still manage the settings some advanced in vSphere HA configuration, but I strongly recommend, try to take the help of someone who has done it before.

  also try to go through other admission control strategies which are explained in the document for more inputs.

• Thunderbird 38.3.0: No writable calendars are configured for the invitations with the provider for Google Calendar 1.0.4

  Hello

  I searched many hours today in the internet and your forums, but it seems that this problem is not solved yet:

  No writable calendars are configured for the invitations with the provider for Google Calendar.

  My Thunderbird is 38.3.0 and the provider for Google Calendar 1.0.4.

  I put calendar.google.enableEmailInvitations; true but it did not help. I also tried [email protected]... @googlemail.com. Calendar works fine, it syncs, I see all the entries etc. But I can't accept invitations even IF she must have write access.

  What can I do? Is there a solution for this?

  Thank you!
  Daniel

  Use CalDAV here to access Google Calendar via lightning. I have no experience with the add-on of the provider.
  In any case, it is my understanding that you must assign an e-mail address to a calendar in order to be able to accept the invitations for this calendar. I see that in your screenshot.
  You can try to remove the Google calendar in lightning and re-create it. Given that all the data is on the server nothing will get lost.
  Or you may want to try CalDAV.
  https://blog.Mozilla.org/calendar/2013/09/Google-is-changing-the-location-URL-of-their-CalDAV-calendars/

• No writable calendars are configured for invitations

  A few weeks ago I created the lightning (with the great help of the participants to the forum of TB) so that when I get an e-mail meeting invitations, I could accept, and they show up on my Google Calendar. A week ago, it stopped working.

  When I receive an invitation, there is no button to accept. Instead, there is a notice that says "no writable calendars are configured for invitations, check the properties of calendar.

  I made sure that Google calendar is present and selected in the tab of the Flash. I checked the calendar properties, and the email address where I receive invitations to meetings (my work email) is set as the e-mail address in the Properties dialog box. And the checkbox is enabled to turn on the calendar.

  Thanks in advance, does anyone have suggestions to get TB/Lightning to work as it did before? That is to be accepted invitations to meetings and automatically add them to my calendar?

  Thank you!

  Well, you can then mark your message as 'Solution' for the topic?
  Thank you.

• Despite my Gmail that is configured for IMAP and continually confirming that my login and my password are correct, that it will not find my account

  My e-mail and password are correct when I try to configure my mail in Thunderbird, but I always get the error message: Thunderbird could not find your e-mail account settings.

  I have also entered with Gmail and was assured that it is configured for IMAP

  Thank you.

• SP A10 - Error 633: the modem is not installed or configured for Dial-Up

  I've already reformatted the hard drive and the utility CD to reinstall the modem driver. Anyone got tips on how to solve the problem? An external modem would solve it?
  Either way, it's a satellite pro A10

  Hello

  If the HARD drive is formatted, use the recovery CD and reinstall the OS. After that, the modem must be recognized and properly installed. After that, configure Dial connection and check the modem. If the modem is not defective, it should work.

  The strange thing is that there is Error 633 which means: the port is already in use or is not configured for remote access remote calls.
  Please check this interesting site http://www.modemsite.com/56k/duns633.asp.
  If there is no success please write again.

  Good bye

• Re: Brooded and configuration for Touchpad

  Win7 x 64
  L505 - 10 M

  It dishes all kinds of problems after an update of security windows for this system a few months ago.

  I put a backup of C:\ return, but various functions did not work.
  I have most of them are still working today. I installed Flashcard again but configuration for touch pad and display are still missing.
  Mouse drivers are HID-mouse PS/2 version: 6.1.7600.16385 Microsoft.
  I downloaded path touch driver - 20091202155841.zip, but it cannot be installed.
  C: \Program Line\TOSHIBA\Bulletin Council is present but likely damaged and not present in Windows Start-menu\Toshiba.
  How can I fix this?

  arnold12

  It is pretty damn good on your laptop.
  Is installation of recovery for you solution?

  I mean, after the new installation of the OS, everything will be OK again.

  All you need to do is to backup all your data and start the installation of the HARD disk.

• Hi, I just bought the Dm11 rhythms... How can I configure for use in Garageband?

  Hi, I just bought Dm11 drum machine apple app, how do I configure for use in Garageband?

  I guess you mean the Mac Version of DM1. The App is not closely integrated with GarageBand. Therefore, you must export each loop/beat you like WAV or AAC and import it in GarageBand.

• Where the smart wizard dowload can configure for OSX (El Capitan)

  Can you tell me where to download smart Assistant can configure for Macintosh OSX?

  Hello DaDirk,

  Welcome to the community!

  I'm sorry, but currently there is no Smart Wizard, Smart Control Center and Prosafe Plus utilities available that are compatible with Mac systems.

  Alternatively, you can configure the switch via user interface using its default LAN IP address on a web browser.

  Kind regards

• Where can I find instructions for alternative configurations for my time capsule?

  I am resident in a House with a router not apple using Uverse.  I just bought a Time Capsule, hoping to use it as a storage drive to backup my imac and mac air.  For the MacAir, I would be like it is able with time Capsule wireless backup, and depending on how I can configure the system, connect the imac directly to the TimeCapsule or wireless connection.

  What I can't do connect the Capsule of time with an ethernet cable to the router not apple, that is in a different room than my desktop.  I have permission to use the internet service provided by the non-apple router - so right now, I don't have time Capsule to provide internet access in itself - as long as it can enable to backup wireless option at least for my mac air.

  Any suggestions?

  Unfortunately, you're stuck in the middle of a router that is not apple and an Apple router without ethernet... and therefore no way to connect.

  What you need is a wireless bridge (wireless to ethernet bridge if you want that it is more accurate).

  Wireless bridges are pretty cheap... Look at TP-Link, because a lot of their wireless access points will make wireless bridge...

  Or you can purchase an airport express... It's the only apple router which allows the wireless bridge. However, it is more than twice the price of an equivalent of non-apple.

  With the bridge... you plug in ethernet on the TC and run the TC in bridge (it is the router bridge)... your clients can then connect to the TC directly and the two backup and get internet at the same time... otherwise you can do it in the order...

  That is, you can plug the TC to the iMac by ethernet. It's a bit complicated, but I've given instructions here. Then you have wireless internet and backup on ethernet... It is indeed the best configuration for the imac.

  Time Capsule using wired for Mac for backup only.

  What you can't do, is use wireless for internet and backup at the same time... you will need to do one and then sometimes switch for the wireless of TC to run a backup... not a great idea.

• HP Pavilion p7-1240: desktop will be falling asleep and wake up, and then on its own since configuration for Windows 10

  Desktop has been configured for 10 Windows Home Premium and works very well.  However, a slight annoyance is whenever I put the machine to sleep, he wakes up in the minute each time.  So I do not use 'sleep' and turn every time that I'm done using it.

  However, I prefer to sleep until needed again.

  Already used administrator command prompt: powercfg /requests to check for power to the sleep problem issues and nothing appeared on the command line.

  Already tried disabling hybrid sleep - no help

  Already turned off all timers wake - no help

  Already changed the power of sleep settings using adapters - no network

  Any help you could give me would be much appreciated. !

  Hi there @Berndtoro,

  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that you have a problem with the computer wake up sleep mode. I'll be happy to help you.

  You've done most of the things I want.  I see that you posted on the malware, which may be what wakes up the computer. Please follow the step of Troubleshooting sleep and hibernate issues (Windows 7).

  Please keep me informed of the progress of things. If you need help, let me know and I will gladly make all that I can to help you.

  Please let me know if that solves the problem by marking this post as "accept as a Solution.
  To simply say thank you, click the Thumbs up below!

  Thank you.

• I can open Office configured for text to speech in Windows XP?

  Original title: Windows XP Pro

  I have Windows Xp, I can open Office configured for speech synthesis

  Support for OpenOffice is here--> http://www.openoffice.org/support/index.html

  And see--> https://forum.openoffice.org/en/forum/viewtopic.php?t=47332

  And--> http://support.microsoft.com/kb/306902

• PIXMA PRO 10 can not configure for WiFi

  Everything works fine on USB key, but I can't seem to configure for WiFI. I am using the recommended network driver

  MP68-victory-mg3200-1_02 - ejs.exe

  but for some reason some it does not detect the network. I use Xfinity and have the router SMCD3GNV. I have a printer HP on WiFi but no luck with this one. I don't have the original CD that came with it I bought it used and the seller couldn't find. Is there a better network driver? Thanks, Jim

  Hi, Jim!

  Thanks for posting on our forum! This community is designed for Canon owners your colleagues help each other any problem they may encounter. If it is a question of time-sensitive, contact our technical support team at the United States is the most effective way to get these issues straightened. They are standing, ready to help you 24/7 by Email http://bit.ly/Canon-Support or by phone at 1-800-OK-CANON (1-800-652-2666) Monday to Friday between 10:00 and 10: 00, et (07:00 to 19:00 PT).

  Thank you and have a great day!

• Computer is not configured for Microsoft FixIt. Why not?

  Original title: when I try to use the hotfix program it won't work and it did until I get a reprt error saying that my computer settings are not configured for microsoft fixit program

  I get an error reprt back saying that my computer settings are not configured for microsoft fixit program

  Hello

  ·         Who solve this running?

  ·         The problem occurs with all fix Microsoft?

  ·         Which exact issue are you facing with the computer?

  Some of the fixit tools are designed to work with specific operating system. If you try to run Windows 7 repair on Windows XP, it cannot run. Please provide us with more information about the issue so that we can help you further.

  If you are faced with the question with all Microsoft Fixit, you can post your query to Microsoft fix Center solution for better support.

  http://social.Microsoft.com/forums/en/fixitcenter/threads