Configuration network problem

Similar Questions

• Configuration network LaserJet P1606dn

  Hello world

  I have a problem with establishing a new LaserJet P1606dn on our network. The installation software provided with the printer assumes the environment uses a DHCP server to obtain an initial IP address and then you can evaluate the printer through the web interface and change it. My problem, we do not have DHCP on our network and I need to set up an IP address on this printer. My question, is there any other utility that can be used to find the printer, and then set the printer with a static IP address.

  Thank you in advanced for assistance.

  Steven

  Too bad. I found another way to access the printer. It seems to have assigned the printer an IP 169.254.x.x wherein I changed my desktop to the same subnet and then access the printers web interface to configure networking for the correct IP subnet.

• Vista unidentified network problem

  My HP G60 laptop under vista home premium got an "unidentified network" problem and not able to get on the internet. I even tried to reinstall vista to factory default, still the same problem with my wireless router.

  Spec:

  -HP G60 laptop computer, running vista Home premium 32-bit, with 3 GB of RAM

  -Belkin router

  -I am able to connect via a fine wired line but with a Wi - Fi, it shows constantly 'unidentified network', even if I changed the Private mode in network and sharing Center.

  -J' tried the following: listed an SSID different router, reset the router by default, to reinstall vista, tried other mechanisms, such as specified in the forum, with no difference

  -When you configure the router, I have clone MAC of the laptop to the router to get the connection with Comcast, has done that with network cable connected, internet connection worked well after cloning.

  -no virus SW installed.

  Any suggestions on what might be the solution here? Thank you.

  Hello

  It seems that something is blocking the wireless to connect to the wireless router and to obtain a valid IP address.

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• PE2950 intermittent network problems

  Hey guys, I have a PE2950 running Windows 2008 R2. It's a (non-primary) domain controller and I'm having all sorts of problems with replication errors. I also have problems with DNS errors.

  When I log on the 2950 and run nslookup ifc.local, sometimes it comes complete with success immediately. Then if I run it again a few seconds later, it expires. I checked the reverse on both servers search areas and have the correct PTR records (it seems) and points NIC of each server to the other server, and then to his self for DNS. There are forwarders in DNS records, but not on the network card. I seem to have no problem with the PDC network (a 1950).

  It seems that my network problem is intermittent and can be hardware/driver related, but I'm not sure. One thing I found interesting is that if I try to activate IPV6 on the 2950's NIC, I receive an error message that says I need to install a network card in order to configure TCP/IP, but there is clearly a here and IP4 is set up very well.

  IPconfig shows also two cards tunnel I'm not familiar with. Clear that they are not used. I would like to disable some how?

  Here are the results of an ipconfig/all and nslookup example. Of course, when I went to this post, I couldn't nslookup to expire, but when he does I have server: UNKNOWN and IP address correct and therefore three lines of time-out.

  Thanks in advance for any help you can offer!

  Windows IP Configuration
  
     Host Name . . . . . . . . . . . . : IFCServer2
     Primary Dns Suffix  . . . . . . . : IFC.local
     Node Type . . . . . . . . . . . . : Hybrid
     IP Routing Enabled. . . . . . . . : No
     WINS Proxy Enabled. . . . . . . . : No
     DNS Suffix Search List. . . . . . : IFC.local
  
  Ethernet adapter Local Area Connection:
  
     Connection-specific DNS Suffix  . :
     Description . . . . . . . . . . . : Broadcom BCM5708C NetXtreme II GigE (NDIS VBD Client)
     Physical Address. . . . . . . . . : 00-1C-23-CF-7E-6E
     DHCP Enabled. . . . . . . . . . . : No
     Autoconfiguration Enabled . . . . : Yes
     IPv4 Address. . . . . . . . . . . : 192.168.2.11(Preferred)
     Subnet Mask . . . . . . . . . . . : 255.255.255.0
     Default Gateway . . . . . . . . . : 192.168.2.1
     DNS Servers . . . . . . . . . . . : 192.168.2.10
                                         192.168.2.11
     NetBIOS over Tcpip. . . . . . . . : Disabled
  
  Tunnel adapter isatap.{865DC311-438F-4420-9B23-0062AF1CFBE5}:
  
     Media State . . . . . . . . . . . : Media disconnected
     Connection-specific DNS Suffix  . :
     Description . . . . . . . . . . . : Microsoft ISATAP Adapter
     Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
     DHCP Enabled. . . . . . . . . . . : No
     Autoconfiguration Enabled . . . . : Yes
  
  Tunnel adapter Teredo Tunneling Pseudo-Interface:
  
     Media State . . . . . . . . . . . : Media disconnected
     Connection-specific DNS Suffix  . :
     Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
     Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
     DHCP Enabled. . . . . . . . . . . : No
     Autoconfiguration Enabled . . . . : Yes
  
  /////////////////////////////////////////////////////////////////////////////////////////////
  

  Server:  ifcserver1.ifc.local
  Address:  192.168.2.10
  
  Name:    ifc.local
  Addresses:  192.168.2.11
        192.168.2.10
  

  Is that what your firmware up-to-date?  There were several problems with these early s NICS that have been addressed through firmware updates and driver (drivers was with 2003... have not heard anything specific about 2008).  You need to update your BIOS and ESM before updated the firmware of the NETWORK adapter.

• ESXi network problem

  I have a strange problem of networking with ESXi, my infrastructure is described below:

  I'm under vCenter 5.5 on a VCSA (5.5.0 update 2d, Build 2442330). The environment is a mixture of ESXi 5.1 (especially U2) and 5.5U1a. We have 1 primary site with 5 sites all remote connected via GRE VPN tunnels, The VCSA is in the main site, each remote site has at least 1 ESXi server managed by the VCSA. Each remote site has independent internet so for each site, the basic router (which ends the GRE VPN) routes inside networks (essentially 10.0.0.0/8) through the tunnel and has a default route to the local firewall. ESXi boxes that are not configured with the router as the default gateway, none of the custom static routes have been added to ESXi.

  Two of my remote sites (a site has two servers ESXi, the other has a site) ESXi servers keep losing contact with vCenter. Nothing else on these networks is never a problem to talk to the main site, including talking to the VCSA. Three servers are different versions of 5.1. Here's what I've done for troubleshooting:

  1. ESXi can ping on virtually any host through the tunnel to the main site with the exception of the VCSA.
  2. I isolated my network management in ESXi to a physical NETWORK card and made a SPAN on the switch port, a capture of packets revealed that when the rattling of the VCSA ESXi put the packet on the wire with a destination MAC of the firewall. For all the other hosts on the main site of subnet ESXi sends the packet with a destination MAC address of the core router. Packet capture on ESXi itself (using tcpdump-uw) shows the same thing.
  3. The ARP tables on all hosts show correct MAC addresses for the router base and the firewall.
  4. Make a "vmkping - I vmk0 - N < core router > < VCSA >" succeeds (destination MAC is correct in this case).
  5. Add a static route to ESXi to the address of the VCSA force it to the top of base does not work, ESXi continues to send the packet to the Mac static routes these firewall have been removed after the failed test of workaround.
  6. Restart the host will solve the problem for a short time.

  Some info:

  These three server 1 is an IBM x 3300 M4 using Intel I350 GB network cards, the other two are R620s from Dell. The R620s each have 1 4-port Broadcom BCM5720-1 4 Intel 82580 ports. IPv6 has been disabled on all three hosts. Right now vmk0 is linked to an Intel NETWORK card on three servers, but barely I started to watch it, so I don't know if we saw the problem with vmk0 with a Broadcom.

  The Dells are inherited, so we have not done installs it but I reinstalled one of them yesterday (it was 5.1 U2 I reinstalled 5.1 U3) at the request of support for VMware. Support noted that the firmware and drivers were outdated and did not meet the HCL for those who have been updated when I reinstalled.

  IBM has been purchased and installed by our care last summer, firmware and drivers correspond to this LIST with the exception of the version of the BIOS that is a future release (it corresponds to the HCL for 5.5).

  I have a pension case, SR 15633456803. Initially, they tried to blame the network. Although it is clear to me that this is not a network problem, I put a case of Cisco in any way. Cisco has quickly threw the evidence I had gathered and made the same determination. The only way that this could be a network problem is with ProxyARP. ProxyARP is disabled on my firewalls, ESXi has correct ARP tables and when you talk to anything on the main network, in addition to the VCSA it sends the packet to the MAC address so clearly not a question of ProxyARP. At this point VMware said essentially that they are running out of ideas. I hope my reinstalled host stay online for more than a week, then I'll reinstall the other two hosts and call it a day if all goes well, but I'm preparing for the possibility that may not happen.

  We never seen anything like this or have any ideas?

  I understand the problem, ESXi does not correctly release the generated ICMP redirects. You can force the issue by restarting the vmk0 interface (or any port of kernel VM is your management interface) VMware KB: Internet control management protocol redirects, because a permanent fix I will disable ICMP redirects on my routers.

• Cannot download the software due to a network problem

  Hi all I'm on MacBook Pro (retina, 15 inches, end of 2013).
  I try to install Windows 10 with the version downloaded from the Microsoft Web site.
  I finished uploaded and am trying to use Boot Camp to install Windows 10.
  However, I faced a question and it is that he "cannot download the software due to a network problem".
  I'm stuck here for an hour and I can't find a solution.
  I did all right until now by the following online tutorial but it prevents me to continue.
  Any help will be appreciated.
  Thank you.

  It is a very common problem. To fix this, first try to start your Mac in safe mode by following these steps-> safe mode try if your Mac does not commissioning - Apple Support

  Then, restart your Mac as usual and try to download the Windows support software again.

• Cannot install updates due to temporary network problems

  Hi need help please teporary network problems are interfering with windows update

  Read this: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/1467f44b-ee27-4f7d-98d7-f1c4b35b3395

  Help us help you.

  Is this relevant: you may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• Recently, I installed Microsoft Works 9, and now I have trouble to download the Windows Update update of security for Microsoft Works 9 (KB967044). I am getting error 646. What is a network problem? ___

  Recently, I installed Microsoft Works 9, and now I have trouble to download the Windows Update update of security for Microsoft Works 9 (KB967044). I am getting error 646. What is a network problem?
  I have also recently set up a wireless network.

  Hello

  Try this 1st to see if it helps, and it should:

  Description of the Patch registration cleanup tool
  http://support.Microsoft.com/kb/976220/

  ------------------------------------------------------

  If necessary :

  Try this - Panel - Windows Updates - on every update that will not be installed - click on the important updates
  or the update itself - double click a view more information (or click top then discovers on the right)

  Those who will take you to a page where you can download the update.

  Or go here and the KBxxxxxx number to download it.

  Download Center - mount the KBxxxxxx.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  Download - SAVE - go to where you put them - click on - RUN AS ADMIN

  Then you can right click on the update in the updates Windows and HIDE.

  If you get an error Installer install this version:

  Windows install 4.5 Redistributable
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

  ----------------------------------------------------

  Then run this:

  How to reset the Windows Update components? -a Mr Fixit
  http://support.Microsoft.com/kb/971058

  Description of the system for Windows Vista, Windows Server 2008, update tool and
  for Windows 7
  http://support.Microsoft.com/kb/947821

  ------------------------------------------------------------
  Because these are all Office updates you might get more information if necessary in the Agency of those groups that
  may have experienced the same problem.

  Office newsgroups
  http://www.Microsoft.com/Office/Community/en-us/FlyoutOverview.mspx

  Microsoft.public.office.misc discussions
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.Office.misc&cat=en_us_01cb749f-c998-4762-8099-df71793c11c7&lang=en&CR=us

  ------------------------------------------------------------

  If necessary you can incident free get reports however the above should take care of it for you.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps and happy holidays!

  Rob - bicycle - Mark Twain said it is good.

• Outlook Express 6: your server has unexpectedly ended the connection. The potential causes for this include server problems, network problems, or a long period of inactivity. Error number: 0x800ccc0f

  Original title: Windows XP and Outlook Express 6

  I have a new computer with outlook express and went through the set up instructions.  When I tried to send a test email, I got this error message:

  "Your server has terminated suddenly the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Account: 'pop.mail.yahoo.com', server: 'pop.mail.yahoo.com', Protocol: POP3, Port: 110, secure (SSL): Yes, error number: 0x800CCC0F. »

  How can I fix this error message and have e-mail sent via Outlook?

  Hi Jeanette Logan,
   
  Here is an article that addresses this issue. Follow the steps listed in the article for this problem:
   
  Troubleshooting error messages that you receive when you try to send and receive e-mail in Outlook and Outlook Express

• Wireless network problem: disconnects randomly anywhere between 1 and 4 hours.

  I have a wireless network problem, it disconnects randomly anywhere between 1 h and 4 h. The network consists of a Samsung 4 G hotspot and a Linksys AE1000. The signal strength is excellent, the AE1000 is 1 ft of the computer and 1 ft of the HotSpot.  The computer is a Dell Dimension 2400. Any ideas?

  Hi Jack,

  Problem solved.  I did 2 assumptions about the original problem.  I assumed that the 2 Tech that I spoke made the hurt their product. Battery saver has been activated on the hotspot.

  Thanks again

  Greg

• Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity.

  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Topic "business profile]', account:"pop.bizmail.yahoo.com", server:"smtp.bizmail.yahoo.com"', Protocol: SMTP, server response: ' 451 see http://pobox.com/~djb/docs/smtplf.html. ', Port: 25, secure (SSL): no, Server error: 451, error number: 0x800CCC0F"

  Your server suddenly put an end to the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Topic "business profile]', account:"pop.bizmail.yahoo.com", server:"smtp.bizmail.yahoo.com"', Protocol: SMTP, server response: ' 451 see http://pobox.com/~djb/docs/smtplf.html. ', Port: 25, secure (SSL): no, Server error: 451, error number: 0x800CCC0F"

  You must make a few changes, not only on outgoing parameters, your incoming parameters also need changes.

  Open your e-mail program > tools > accounts > your bizmail account > properties > servers, under outgoing mail server, check "this server requires authentication" > apply > advanced, under outgoing (SMTP) mail change to 465 not 25. Put a check mark on "this server requires a secure connection (SSL)" > under incoming (POP3) mail, change it to 995 no 110. Put a check mark on "this server requires a secure connection (SSL)" > OK

  t-4-2

• Whenever I have a network problem and solve this problem, my computer is given a different number. For example, I'm a 4 device on my network, but I want to be the number of device 1.

  Whenever I have a network problem and seem to fix I get a new network number and now is showing Network 4. How can I get that back at number 1?

  I see this on my Vista Machine as well as my 7 machine

  original title: Networking

  Remove the connection from the Device Manager and reinstall the network drivers.

  Check also:

  Windows 7 - Rename network connections in Windows 7
  http://www.SevenForums.com/network-sharing/24286-Rename-network-connections-Windows-7-a.html

  Unidentified network is displayed on every reboot of Windows 7 and stop access NW
  http://social.technet.Microsoft.com/forums/en-AU/w7itpronetworking/thread/3f8999b6-495D-4065-9825-2271b4c898f6

• How can I configure network server in blackberry phones smart blackBerry bold 9700

  How can I configure network server in blackberry bold 9700

  I want that my third-party applications to access the organization intranet using your organization's network.

  When I tried to change the permissions of third-party application, it shows RIMconnections, interactions, data from the user... don't allow, deny permission is there.

  How can I set thesehttp://docs.blackberry.com/en/smartphone_users/deliverables/23895/Third_party_application_connection...

  Yes, if you read the link you posted, these settings are for OS6 and higher devices.

  Not for OS5 and you're on OS5.

• Network problem between Windows 7 laptop with the Windows XP desktop computer via Linksys WRT54 router.

  Original title: network problem!

  How can I get my laptop with Windows 7 Home Edition to connect to my desktop with Windows XP on it. I have a router Linksys WRT54 plugged directly to the desktop via ethernet and my laptop has an excellent signal but I can't access programs or the printer with it. I know the 'host group' on 7 but XP isn't that. Are there alternative than to put 7 on my desktop? Any suggestions?

  Thank you!

  Hello

  Thanks for posting your query in Microsoft Community and we give the opportunity to help you.

  According the description of the problem face you connection problems in Windows 7 laptop with the Windows XP desktop computer via Linksys WRT54 router.

  Residential group option is available on Windows 7 and Windows 8 operating systems. However, you can see the following article for more information on the connection of Windows 7 and Windows XP computers:

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-in/Windows7/networking-home-computers-running-different-versions-of-Windows

  Hope this information helps. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you.

• "The profile could not be signed on-line. There may be a network problem or the Windows Live ID service may not be available. »

  "The profile could not be signed on-line. There may be a network problem or the Windows Live ID service may not be available. »

  Please help Thierry

  You can send me a mail on * address email is removed from the privacy * when you got an answer for me.

  Hi ziphovicHlubi,

  When exactly do you get this error message?

  Try the steps from the following link:

  Games for Windows LIVE: you can not connect to LIVE and you receive an error message
  http://support.Microsoft.com/kb/938705
  http://www.Microsoft.com/games/en-us/support/pages/technicalissuesguide.aspx

  If the steps above fail, then I suggest you to post:
  http://windowslivehelp.com/