Configuration of the IPS Cisco 2921

Similar Questions

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• Can Cisco Configuration Professional to use the IPS feature?

  Dear Expert

  Hello.

  Could you tell me about Cisco Configuration Professional.

  I would try the IOS - IPS on Cisco2901-SEC/K9.

  I was looking to the ORC on Cisco Configuration Professional.

  Cisco2901-SEC/K9 does not support SDM.

  But the Cisco2901-SEC/K9 support the Cisco Configuration Professional.

  Can you Cisco Configuration professional to use IPS as SDM function?

  Kind regards

  Takuro.

  Hello

  Yes, you can configure Cisco Configuration Professional IOS IPS.

  CCP has a wizard to guide you through the process, there is a link for it:

  http://www.Cisco.com/en/us/prod/collateral/iosswrel/ps6537/ps6586/ps6634/prod_white_paper0900aecd8066d265.html

  I hope this helps you.

  -------

  Mashal

• The ACE IPS Cisco and Cisco ASA AIP - SSM (IPS)

  Is there a difference between the features offered by the Cisco ACE IPS and Cisco ASA AIP - SSM (IPS) devices?

  Can we do without Cisco ASA AIP - SSM (IPS) of 'only' configuration/implementation Cisco ACE IPS.

  Cisco AVS/ACE emphasis on commissioning and to secure web-based applications. IP addresses do not focus on just the web applications and trying to get the multiple layers of the OSI stack. Consider the IPS as a general practitioner and the ACE/AVS as an eye surgeon, or something :)

  Here is the response from Cisco itself:

  http://www.Cisco.com/en/us/prod/collateral/modules/ps2706/ps6906/prod_qas0900aecd8045867c_ps6492_Products_Q_and_A_Item.html

  Q: how is Cisco AVS Firewall application differs from an intrusion prevention system (IPS)?

  A. IPSs are solid solutions of protection against targeted attacks of known vulnerabilities in major platforms such as Windows, Solaris, Apache or Microsoft Internet Information Services (IIS). Cisco AVS excels to protect against targeted attacks Web sites or enterprise applications. These applications can be built custom internal applications or software vendor. Signatures and security patches are generally not available for these types of applications, and building these security levels in each application, it would be almost impossible.

  Q: how is Cisco AVS Firewall application differs by a network firewall?

  A. The Cisco AVS 3120 and Firewall network such as the Firewall of Cisco PIX® and Cisco ASA 5500 Series Adaptive Security appliances are complementary products. The application Cisco AVS Firewall secures Web applications; excellent network in the network security firewall. and the Cisco AVS provides defense in depth for Web applications.

  Firewall network apply policy networks, IP addresses and ports; they have a wide range of application for many different protocols layer features. The firewall can and will be deployed in many locations, including the edge, edge of the enterprise network, branch, etc. Cisco AVS imposed the policy on data HTTP as URL, headers and parameters. Cisco AVS is deployed in the data center in front of Web applications

  Concerning

  Farrukh

• Correct configuration of the Cisco Access Point 1242AG

  Hi all

  Here's the situation:

  Recently, we decided to create a small network of WLAN in our company. We choose the Cisco AIR-AP1242AG-E-K9 with 2x2.4GHz 2.2dbi rotating dipole antenna.

  For better management, a new VLAN routable (ID:20) added to our router IP 192.168.55.1 and SNET 255.255.255.0

  Then, I made the following configurations in the autonomous AP through WEB Console:

  • Static IP:192.20.10.35, SNET:255.255.254.0, GWY:192.20.10.200
  • Vlan1 (native) and VLAN20 (Radio0 - 802.11 g) added in Services.
  • I put the encryption against zero for VLAN1 Mode and cipher AES-CCMP for VLAN20
  • In Server Manager, I've defined a new 192.20.10.35 RADIUS server (AP-IP) and a secret shared and left the default ports for authentication and accounting (1645 and 1646). Also, in the default server priorities section I put focused 1 time for authentication EAP and the IP (Radius Server) 192.20.10.35 Access Point MAC.
  • During the General local RADIUS server configuration, I add as a server for access to the network current (AAA client) the same IP address and the shared secret as the ones I use during the configuration of the RADIUS server above. In authentication protocols enable I left checked only the JUMP and the Mac. In addition, in the users individual section 2 new users created with passwords.
  • In the SSID Manager a new hidden SSID created for interface Radio0 - 802.11 g, associated with VLAN20 and in the Client authentication settings section, I left as accepted authentication open with MAC and EAP authentication method. Also, I left the option to use by default for EAP and MAC authentication servers in Server priorities Section and finally I choose mandatory for key management in the section Client authenticated and active the option enable WPA key management.

  I can ping VLAN20 IPs from any PC which is a member of the VLAN native both AP

  As wireless clients, I use 2 Motorola MC5574 with Windows Mobile 6.1 professional. Both of them have a WLAN Jedi adapter that is configured with the following:

  IPs:192.168.55.10 and 192.168.55.11

  SNET:255.255.255.0

  GWY:192.168.55.1

  In addition, a unique profile has been created on all of them to use for the authentication of the association AP. Each profile has been configured for WPA2-Enterprise with AES and LEAP and identification information predefined user (those defined in the PA for individual users)

  The problem:

  Association of clients with AP is always successful but, authentication fails, and I can't ping the AP IP, IP VLAN20, nor the other customers.

  What I'm missing here? I'm sure it's quite simple somenthing but although I tried several different configurations (even WPA - PSK, WPA2-PSK with TKIP) I always find myself without an appropriate solution to unable to ping.

  Thanks in advance for any help

  Hello

  Can you please paste the show run out of AP?

  Kind regards

  Madhuri

• Check the IPS configuration

  I am very new on the front of Cisco IPS and have configured an ASA 5510 with the SSM-10 IPS module.  We have a compatible interface with multiple VLANs on this interface.  I installed the IPS, to the best of my ability, and I think it's okay as inline doesn't open in a configuration of active / standby asa.  Is it possible to check that the traffic flows properly to this IPS module?  Also, I've mentioned on the Setup it of because this version of the IPS, if I understand correctly, will not allow pairs VLAN, then when I put the policy to inspect all traffic, this traffic inspected between all the VLANS.  Another mystery, this is when I discovered my IPS interfaces (management and is not) that is not configured as management shows no matched.

  I know it of a lot, so let me summarize:

  -How can I check that my setup works as intended where all traffic between all them VLAN is inspected.

  -Why my interface managers showing 'matched '.

  -Looking through all of the Cisco documentation, I noticed the mention of the "contexts"; I don't see any reference to these contexts within the IDM.  It's just for my knowledge, but may be necessary for installation... I do not know.

  Thank you!

  Hello Mote, heat

  With regard to your questions:

  -How can I check that my setup works as intended where all traffic between all them VLAN is inspected?

  Since you're using an IPS module, traffic that matches the class configured on the SAA is under inspection, you can configure a capture on the dataplane Interface (the Interface used to send traffic to the ASA to IPS) using this command:

  capture ips int asa_dataplane buffer 15000000

  Check capture using the:

  See the FPS capture

  The output should display the packets from for each VLAN.

  -Why my interface managers showing 'matched '?

  

  Modules ASA IPS (ASA 5500 AIP SSM, ASA IPS 5500-X SSP and ASA IPS SSP 5585-X) do not support pairs VLAN inline.

  You can associate a VLAN in pairs on a physical interface. This is known as pair mode for the VLAN inline. Packets received on one of VLAN matched are analyzed and then forwarded to another VLAN in the pair. Because the module has only a detection interface, this is why it is shown as Unpaired.

  Literature speaks of "security contexts. You can partition an ASA unique in several virtual devices, called security contexts. Each context is an independent device, with its own security policy, interfaces, and administrators. Several contexts resemble have several stand-alone devices. Many features are supported in multiple context mode, including the routing tables, features of firewall, IPS, and management.

  Please rate the answer if you find it useful.

• Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.

  Configure the router Cisco E2000 wireless for my laptop HP with Vista, I can't work.  I spoke with Cisco and they said that my Atheros AR5007 adapter does not work with Cisco E2000 and contact my computer vendor

  Hello

  HM... I guess that the Cisco people know what they're taking everything. The AR5005 is a b/g card and there should be a good reason to not work with a router that is able (the E2000 is able g) g.

  This is HP drivers for the card, http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?cc=us&lc=en&dlc=en&softwareitem=ob-55737-1

  If you can't make it work, you must decide between a new card or another router.

  Personally, if it's new and I could return it, I'd get a different router model. But YMMV

  ------------

  My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• D9036 - GUI Login - IP Configuration of the Cisco encoder

  Dear all

  I try to open D9036 encoder Cisco to get access to the Web Interface of GUI.

  In the manual of the encoder, Cisco informed that we have to connect via RS232 to the encoder and configure its IP address, but I did not

  but I noticed that the encoder Eth1 has an IP "192.168.1.100" and whenever I am trying to ping ping.

  Please advice for the method to connect to the encoder via the Web Interface of GUI.

  Follow these steps:
  1. access to the serial port on your PC.

  2 in the main connection, type root and then press ENTER.

  3 at the root prompt, type set_mgmt_port_config.py and press ENTER.
  4. When you are prompted, type a pair of IP address/netmask and press ENTER.
  5 if necessary, at the prompt of gateway IP address configured, type y to set the IP address of the gateway and press ENTER.
  6. at the prompt of gateway IP address, type the IP address of the gateway and press ENTER.
  7 at the prompt of the writing MGMT port configuration file, type y and press ENTER to save the configuration file.

  8 networking restart for guest MGMT port, type y and press ENTER to apply the changes immediately.

  9 type ifconfig to check the ip address.

  10. after the above steps, try to encode via GUI. It should work.

• The services configuration of firepower on Cisco asa 5506 with ASDM

  I have a few 5506 firewalls, and they are fully licensed with services of power, control, Protection, URL filtering, malware. I have intend running and configuration of all of this on the 5506 by ASDM. I was wondering if there are guides for a basic configuration and the implementation of policies available. Something to show a basic configuration which would technically begin inspection of traffic and work. Then I can edit and make changes to my taste.

  Thank you

  My recommendation to clients is to look at the Cisco Live, BRKSEC-2018presentation. Please refer to the 56 slide from for a good overview of how policies are installed in a module of firepower.

  There are also a number of other detailed guides available in the FireSIGHT Management Center product support page should you care to learn more about customization and operations. You can also find the series of videos of ASA FirePOWER on request to Labminutes.com useful to guide you on execution of operations of your system.

• The ISE Cisco switch configuration

  Hi experts,

  I got the following network:

  Devices-> switch access-->--> access switch central office switch-> ISE Server

  All switches are capable IOS for the 802. 1 X and configurations of AAA for ISE to manage network devices. However, I read in the guide on the configuration of the switches in preparation for the deployment of the ISE of CIsco, but I wonder what should I configure switches for access and basic switches or only configure the switches for access to EHT?

  Thanks for your time to read!

  If all clients are non-DHCP clients, then no configuration is based or distribution at all.

  But you may need to search different options of profiling, if the customers are not active DHCP. Access switch supports the function of detection IOS? Would be very useful to have such a that it would send important profiling information at ISE. You may need to use the right options for ISE of profiling to determine the details of the endpoint.

  Concerning

  Vivek

• Configuration of the Cisco ACS Radius

  Hello

  I'm trying to set up authentication radius on cisco ACS but short question. When I set up my group of network devices in the configuration of the AAA Client as one of ray device groups, my authentications fail with authentication as a failure code"

  CS invalid password' but when I change my group of devices to "Unassigned", everything started working.

  On my AAA client, when authentication fail, I see

  Server RADIUS audit package fails:

  Please note that the AAA client is a non-cisco device.

  Any suggestions?

  It seems that you run ACS 4.x. You are facing this problem because the key is set on the excessive rides of the level (Group of devices network XYZ in your case) NDG key at the level of the AAA client.  Please make sure that you don't have different secret key on the client inside the NDG AAA and on the NDG himself.

  Not affected is working because it has no key defined in the NDG.

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/NetCfg.html#wp342738

  "Each device that is assigned to the network device group will use the shared key you enter here. The key that has been attributed to the device when it has been added to the system is ignored. If the Enter key is null, the key of the AAA client is used. »

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• Need help with the configuration of the Site with crossed on Cisco ASA5510 8.2 IPSec VPN Client (1)

  Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).

  Here is the presentation:

  

  There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.

  I was able to configure the Client VPN IPSec Site

  (1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa

  (2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.

  But I was not able to make the tradiotional model Hairpinng to work in this scenario.

  I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?

  Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:

  LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)

  race-conf - Site VPN Customer normal work without internet access/split tunnel

  : ASA Version 8.2 (1) ! ciscoasa hostname domain cisco.campus.com enable the encrypted password xxxxxxxxxxxxxx XXXXXXXXXXXXXX encrypted passwd names of ! interface GigabitEthernet0/0 nameif outside internet1 security-level 0 IP 1.1.1.1 255.255.255.240 ! interface GigabitEthernet0/1 nameif outside internet2 security-level 0 IP address 2.2.2.2 255.255.255.224 ! interface GigabitEthernet0/2 nameif dmz interface security-level 0 IP 10.0.1.1 255.255.255.0 ! interface GigabitEthernet0/3 nameif campus-lan security-level 0 IP 172.16.0.1 255.255.0.0 ! interface Management0/0 nameif CSC-MGMT security-level 100 the IP 10.0.0.4 address 255.255.255.0 ! boot system Disk0: / asa821 - k8.bin boot system Disk0: / asa843 - k8.bin passive FTP mode DNS server-group DefaultDNS domain cisco.campus.com permit same-security-traffic inter-interface permit same-security-traffic intra-interface object-group network cmps-lan the object-group CSC - ip network object-group network www-Interior object-group network www-outside object-group service tcp-80 object-group service udp-53 object-group service https object-group service pop3 object-group service smtp object-group service tcp80 object-group service http-s object-group service pop3-110 object-group service smtp25 object-group service udp53 object-group service ssh object-group service tcp-port port udp-object-group service object-group service ftp object-group service ftp - data object-group network csc1-ip object-group service all-tcp-udp access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3 access-list extended SCC-OUT permit ip host 10.0.0.5 everything list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3 access CAMPUS-wide LAN ip allowed list a whole access-list CSC - acl note scan web and mail traffic access-list CSC - acl extended permit tcp any any eq smtp access-list CSC - acl extended permit tcp any any eq pop3 access-list CSC - acl note scan web and mail traffic access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4 access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp

  access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3

  access-list extended INTERNET2-IN permit ip any host 1.1.1.2

  access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0

  access list DNS-inspect extended permit tcp any any eq field

  access list DNS-inspect extended permit udp any any eq field

  access-list extended capin permit ip host 172.16.1.234 all

  access-list extended capin permit ip host 172.16.1.52 all

  access-list extended capin permit ip any host 172.16.1.52

  Capin list extended access permit ip host 172.16.0.82 172.16.0.61

  Capin list extended access permit ip host 172.16.0.61 172.16.0.82

  access-list extended capout permit ip host 2.2.2.2 everything

  access-list extended capout permit ip any host 2.2.2.2

  Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0

  pager lines 24

  Enable logging

  debug logging in buffered memory

  asdm of logging of information

  Internet1-outside of MTU 1500

  Internet2-outside of MTU 1500

  interface-dmz MTU 1500

  Campus-lan of MTU 1500

  MTU 1500 CSC-MGMT

  IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1

  IP check path reverse interface internet2-outside

  IP check path reverse interface interface-dmz

  IP check path opposite campus-lan interface

  IP check path reverse interface CSC-MGMT

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  ASDM image disk0: / asdm - 621.bin

  don't allow no asdm history

  ARP timeout 14400

  interface of global (internet1-outside) 1

  interface of global (internet2-outside) 1

  NAT (campus-lan) 0-campus-lan_nat0_outbound access list

  NAT (campus-lan) 1 0.0.0.0 0.0.0.0

  NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255

  static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255

  Access-group INTERNET2-IN interface internet1-outside

  group-access INTERNET1-IN interface internet2-outside

  group-access CAMPUS-LAN in campus-lan interface

  CSC-OUT access-group in SCC-MGMT interface

  Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1

  Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  dynamic-access-policy-registration DfltAccessPolicy

  the ssh LOCAL console AAA authentication

  AAA authentication enable LOCAL console

  Enable http server

  http 10.0.0.2 255.255.255.255 CSC-MGMT

  http 10.0.0.8 255.255.255.255 CSC-MGMT

  HTTP 1.2.2.2 255.255.255.255 internet2-outside

  HTTP 1.2.2.2 255.255.255.255 internet1-outside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  crypto internet2-outside_map outside internet2 network interface card

  Crypto ca trustpoint _SmartCallHome_ServerCA

  Configure CRL

  Crypto ca certificate chain _SmartCallHome_ServerCA

  certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as

  a67a897as a67a897as a67a897as a67a897as a67a897as

  quit smoking

  ISAKMP crypto enable internet2-outside

  crypto ISAKMP policy 10

  preshared authentication

  aes encryption

  md5 hash

  Group 2

  life 86400

  Telnet 10.0.0.2 255.255.255.255 CSC-MGMT

  Telnet 10.0.0.8 255.255.255.255 CSC-MGMT

  Telnet timeout 5

  SSH 1.2.3.3 255.255.255.240 internet1-outside

  SSH 1.2.2.2 255.255.255.255 internet1-outside

  SSH 1.2.2.2 255.255.255.255 internet2-outside

  SSH timeout 5

  Console timeout 0

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  internal VPN_TG_1 group policy

  VPN_TG_1 group policy attributes

  Protocol-tunnel-VPN IPSec

  username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx

  privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx

  username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx

  username vpnuser1 attributes

  VPN-group-policy VPN_TG_1

  type tunnel-group VPN_TG_1 remote access

  attributes global-tunnel-group VPN_TG_1

  address vpnpool1 pool

  Group Policy - by default-VPN_TG_1

  IPSec-attributes tunnel-group VPN_TG_1

  pre-shared-key *.

  !

  class-map cmap-DNS

  matches the access list DNS-inspect

  CCS-class class-map

  corresponds to the CSC - acl access list

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  message-length maximum 512

  Policy-map global_policy

  CCS category

  CSC help

  cmap-DNS class

  inspect the preset_dns_map dns

  !

  global service-policy global_policy

  context of prompt hostname

  Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y

  : end

  Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN

  Please tell what to do here, to pin all of the traffic Internet from VPN Clients.

  That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)

  I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.

  Thank you & best regards

  MAXS

  
  

  Hello

  If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.

  I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.

  The command format is

  packet-tracer intput tcp

  That should tell what the SAA for this kind of package entering its "input" interface

  Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)

  -Jouni

• Default configuration of the PFS on the Cisco ISR

  Hello

  I want to learn more about the default configuration of PFS on the Cisco ISR router.

  -Introduction to IP Security (IPSec) encryption - create a Crypto map
  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_tech_note09186a0080094203.shtml#cryptomap

  You can also change the configuration of your PFS here. PFS Group1 is the default value in this example. You can change the PFS to group2, or turn off all together, you should not do.

  DT3-45 a (config) #crypto card armadillo 10 ipsec-isakmp
  DT3 - 45's (config-crypto-map) #set counterpart 192.168.10.38
  DT3 - 45 session key has seconds (config-crypto-map) #set 4000
  DT3 - 45's (config-crypto-map) #set transform-set HAAT PapaBear BabyBear
  DT3 - 45's (config-crypto-map) #match address 101
  --------

  This example has no configuration PFS PFS is set to group1.
  However, the following command reference indicates that PFS is not requested.
  Which is the correct description for the PFS setting?

  -the pfs value
  http://www.Cisco.com/en/us/docs/iOS/Security/command/reference/sec_s2.html#wp1063163

  Default values
  By default, it is not required of PFS. If no group is specified with this command, the Group1 keyword is used by default.
  -------

  Thank you for your cooperation in advance.

  Order is correct.

  If pfs set is not configured in the crypto map configuration, pfs will be negotiated not.

  If set pfs is configured without any group, then it uses default group1

  And if you do not want to use the other group, you set the group # in the command set pfs.

  I hope it is clear now.

• SSL VPN may be configured on the router from Cisco 881/K9?

  I'm now confused if SSL VPN can be configured on the router from Cisco 881/K9.

  Please someone advise me.

  If Yes, for only 5 users, what I need to buy the license or license is supplied with the router?

  Thank you.

  Yes, and you need a license:

  FL-WEBVPN-10-K9

  License SSL VPN functionality for up to 10 users (incremental), to 12.4 T based only IOS versions

  FL-SSLVPN10-K9

  License SSL VPN functionality for up to 10 users (incremental) for the only based 15.x IOS versions