Configuration of the problem of presets

Similar Questions

• The network configuration of the problems using my IP as URL - VMWare?

  Hello

  I had a few problems with trying to use my IP (via VMWare Player - Enterprise windows serv. 2008) but I keep getting as the page is not responding or these error messages. What I try to do is host a Web site on the server PC with IIS, but I do not know why it does not have to run it during the INVESTIGATION period (of course it works on localhost) but is not relevant in this case I guess... However, I was wondering if it MIGHT be some network setting within parameters of VMWare Player? For the moment under "Network connections" in the control panel I "Bridged: directly connected to the physical network.

  PS The IPv4 address on windows server 2008 ends par.200, while my pc (host) ends (3). Yesterday, I managed to make the WinServ avoir.19 on the end, I don't know if it matters in this case however.

  P.S.S. The right ports are open as well, so I don't really understand why it does not work...

  I hope that someone of you guys can help me solve my problem-i would be very grateful!

  Best regards

  Anton

  Lets start with some basics, the guest has base of Internet/network connectivity?  In other words you can access Internet from the guest operating system?  Also, the host can successfully ping the IP address of the host and the guest can successfully ping the IP address of the host?

• Found that this problem was due to windows being disabled "Wireless Zero Configuration" service. Found this automatic setting and then by installing the software corrected the problem.

  How to get through this process of changing windows 'Wireless Zero Configuration' service is disabled.  Found this automatic setting and then by installing the software corrected the problem.

  Hi Joseph,.

  1 are you always face the question or the issue are already fixed?

  2 Windows operating system you are using?

  If you still experience the problem, you can follow this link completely and check if the problem persists.

  In the Windows wireless network connection problems

  You can also read the following article and check.

  How can I disable wireless configuration and enable Windows XP Wireless Auto Configuration services

• HP Officejet Pro 8500 A909a USB 3 questions about the configuration of the network - port USB3 problem

  Fujitsu Windows 7 laptop (all USB2)

  used the full software and installed a printer HP Officejet Pro 8500 A909a Series as a network printer.

  The printer installed fine and don't have USB connection

  All the software and scanning twain installed, so I was able to scan the copy etc.

  I could browse and choose my PC from the front panel of the printer

  However, it was Tuesday confirmed to a friend that their printer would work on a new laptop - bought the laptop

  Fujitsu - but more recent model with 3 USB ports

  I have install and then used the same FULL configured driver to be installed (V14)

  selected as a network printer and then, during the installation, I get an error hardware error USB and USB drivers

  All the USB works, that I've used - BUT the printer is networked and no USB used

  tried to download the driver and install it-exactly the same question

  SO I configure using the devices and printers 'add printer' network and installed

  I can print OK

  BUT no analysis facilities

  and on the façade - cannot see the new PC to scan to

  The only real difference, is that this PC has USB3 and only mine has USB2

  DO not know why on a network installation USB even when searching for

  It's a problem because Drivet package not has not been updated for USB3 - y at - it a patch?

  Thanks for any help / advice

  Hi etaf,.

  I guess the short answer is: Yes, the problem with the software and the 3.0 Port.

  The long answer with a possible work around is as follows: first of all, the software looks for minimum requirements. Because the software is older, he doesn't know what a 3.0 port. You are right when you say that it should work since you do not use the USB and use wireless instead, but this is not the case.

  There is something we can try, but I can't guarantee it will work. I thought first we could connect a USB cable and run the software made to force the software to see the USB port, but then the software wouldn't even get far enough because you can't plug the cable to the most later in the installation.

  My second thought and most promising suggestion is to connect the USB cable (although we do normally not until the software prompts us to) and use the installation wizard HP Print to get the insteaad of software to use the CD or download from the printer driver page. Still, I can't say with certainty that it works, but I don't see why it would not be worth a try.

  If it works, and we get the software installed you can convert the USB connection to a wireless connection using the software. Fingers crossed! Download and run the with the following link. Printer HP install wizard for Windows

  If this does not work, or you don't want to bother with it (not worth trying), I might consider getting a new model of the printer. You can even call HP. They might be able to offer a discount on a newer model. If you are in the Canada, U.S. dial 800-474-6836 or you can Contact HP worldwide.

• Error: "Windows cannot start because of a configuration of the disk of the computer problem" in computer Dell Dimension 2400 Windows XP startup problem.

  Original title: problem starting on a Dell Dimension 2400 - how to set up the drive with a keyboard.

  I have a Dell Dimension 2400 with Windows XP, start, he can't go to the home screen, so I can't use the suggestions to start right click.

  The error message indicates "Windows did not start because of a configuration of the disk of the computer problem".
  "Cannot read disc startup selected." check material stand of disk and the path.
  How to set up or fix this problem with a keyboard

  Hi MarieButler64,

  You did it of any material changes or software on the computer before this problem?

  You can follow this link & check if the problem persists:

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  Hope the helps of information.

• Get the following error on reboot of the computer: Windows did not start because of a configuration of the disk of the computer problem

  Original title: where can I download iso windows xp recovery CD

  I have a file.which damaged boot.ini file later, when I restart it could not start, with the message:
  Windows did not start because of a configuration of the disk of the computer problem.

  Could not read from the selected boot disk. Check the hardware path and startup disk.

  Please check the Windows documentation about the configuration of disk material and your reference manuals of the equipment for more information.
  So I need an iso file XP Recovery.
  I can simply copy the iso files on USB and start with usb?

  Hello

  1. don't you make changes on the computer before this problem?

  First I suggest you try the troubleshooting methods provided in the following article and the check if that resolves this problem.
  Error message: "Windows did not start because of a configuration of the disk of the computer problem.
  http://support.Microsoft.com/kb/314477

• How to "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected startup disk... "on a netbook without a CD/disk drive?

  I did a lot of research and unfortunately havnt found a road toward the front of the detroit to a fix. Long story short... I installed Jolicloud as a dual boot with windows xp on netbook gateway of my wife. This netbook has no cd/dvd drive. Jolicloud wanted to screw up the startup option to not allow me to boot into windows, going Strait to jolicloud without option of windows. I tried to change it via the "menu.lst" and Grub.cfg file (I think) the only value I changed was I think 'boot... ". ' value between 1 and 2. When I restarted, then finally got a startup list (although I don't think that my modification of the value gave me the list, I had already installed manually "Grub" via the cmd prompt. I should have just restarted from there without changing anything else... because when I chose 'windows xp' in the start menu... He gave me a black screen and kept going back to the start menu. Then, I tried the "Vista loader" option... hoping that it would some how solve my problem... He asked me if I wanted to run a repair any. I agree with him and when he finished he told me that there is no enough space on the hard disk to copy the files (or something like that) then it froze kind of there. I had to do a hard reboot after that that it froze, then I got the code "Windows did not start because of a computer disk configuration problem. Could not read from the selected boot disk.  check the hardware path and startup disk, please check the windows documentation about hardware disk configuration and your hardware for more information reference manuals.

  Again, I have no drive cd/dvd on a netbook... IM assuming that im going to have to return a key USB with windows boot info to load the Manu F2 at startup... But I do not know... Help, please. Thank you

  Hello

  Follow method 1 and 4 in the article below and check if that helps resolve the issue.
  Error message: "Windows did not start because of a configuration of the disk of the computer problem.
  http://support.Microsoft.com/kb/314477/en-us

  I hope this helps.

• Dual Boot with windows XP Pro with 2 HARD drive, error on secondary windows install: "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check boot path and disk hardware... »

  Hi, I recently bought a new Hitachi 1 TB internal hard drive. I wanted to do a clean install on the new drive (d), be able to dual boot my computer and leave my old 300 GB disk (C :) as the primary windows installation. After physically installing the new HARD drive, I noticed that "new hardware found" and the the brand name flashed in the bottom right corner. I thought I'd see the new hard drive in my computer, but I did not. I initialized the new HARD drive with the computer management window (right click on my computer - manage) and I also formatted in NTFS (I had to change my printer hard drive letter to assign the new HARD drive with the letter D, but I've made other changes after this step). Now, I could see and use in my main windows on the C: installation. I then installed a windows new copy XP pro with the installation CD I got for my C: but on the D: (Note: I have a Dell computer (and the Dell reinstallation CD) and my current version of windows has SP3 while the installation CD is only SP2) (I also reformatted my HARD drive during the installation of windows to NTFS)

  Now when I try to start on installing the new on my D: I get "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check startup disk and hardware access path. "and another line saying to refer to manuals HARD drive and windows.

  My Boot.ini file at this time was:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I looked towards the top of this help page, but for now I'm unlucky:

  http://support.Microsoft.com/kb/314477

  (The next steps I took by throwing from the Windows CD and go into the repair console)

  I tried to use the bootcfg /rebuild but the line to boot.ini for my secondary HARD drive still does not work.

  He gave me something like:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (1) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I also tried to change the signature() to multi (0), but it did not work. (or try almost all possible permutations of disk() and rdisk() partition() 0 to 2).

  I also tried to use expand F(dvd-drive):\i386\ntkrnlmp(I_have_a_duo-core).ex_ D:\windows\system32\ntoskrnl.exe and a few other combinations, but I when I login as D:\windows simply, it fails to extend with a message like "could not develop" or C:\windows I get "restricted access".

  I have not yet tried CHKDSK/r, but since I did a clean install on a newly formatted drive... I don't think it would work.

  I've also marked the partition on the D: as active (in computer management), but it did not help me.

  I've done a first installation of windows repair, strangely, I couldn't fix this one... Still does not work...

  My default windows installation yet works very well & I see that windows has been installed on the D: but I'm ideas from how to operate the dual-boot, can someone throw me a BONE on what to do?

  Maybe try to do something with the Boot Manager (whatever it is?) Create a new partition and use it as a boot manager? I don't really want to do this, because if I made a mistake I will be unable to use my computer and dual boot should work without going through all this trouble... But I found this page: http://technet.microsoft.com/fr-fr/library/ee829686%28WS.10%29.aspx

  Could a clean install two HDD help? I hope I won't have to do...

  Someone has an idea?

  PS: I'm not such an advanced user so I need a solution step by step, thanks!

  Edit: I also noted that I can't see my new HARD drive in my BIOS... weird... SATA-0 is my old drive HARD 1 and 2 are my dvd 3-5 readers are 'off' and it doesn't seem to be anything that it is plugged in. I also have 4 bays for internal HARD disks. Now, 2 are busy.

  Edit2: I looked inside my case and enabled the good Sata in the Bios after a reboot it detected the drive correctly. Dual boot doesn't always work well... The fact that it was disable in the BIOS while I was installing the new HARD drive could change anything? Hmm...

  In case I wasn't clear enough: I had a windows XP Pro installed on my C:, bought a new hard drive and installed the same copy of windows on it (d). I think that should allow me to double boot between the two installs different. Even if for some reason I can't boot from one on my D:. Andrew, I do not understand why you so far physically disconnect the other drive, the point of the whole operation is to build a boot.ini file so that the BIOS knows that it y facilities 2 windows and you allow to choose (and not have conflicting problems between the 2 systems), someone correct me if I'm wrong? "Expand" the part of my first post made reference to one of the solutions provided by Microsoft in the first link that I have included in my previous post (but I can't seem to work).

  In addition, it is the procedure that I followed: http://www.ehow.com/how_5950826_boot-two-different-hard-drives.html

  (except I've had the first installation already done).

  Andrew "also, once a new hd is plugged on the pc & running, most of the BIOS will place (them) as 1st priority hd, set the BIOS to do this", you mean that by installing separately from windows on each unit when the other is not plugged in, I could choose what disk to start from defining their priority in the BIOS once they are all plugged back? It's too tedious (as I intend to move frequently between the 2 installs) and requires a computer to other users of the lack of computer knowledge. Unfortunately, it is not a viable option.

  EDIT: I DID IT! Hmmm... Well, I double checked in the recovery console, the path of the new HARD drive with the arc command Scan. Tried to start again with the MULTI (0) in my boot.ini and it worked... I also had my windows install CD in. Maybe that is why I could not start, windows needs the CD to complete the installation? Weird, I don't know what I did to the difficulty it... but hey, it works! Thanks for your ideas guys!

• The volume of the recorded sound is very low when played. I tried to solve the problems through Control Panel of configuration-sound options and increased the volume to 100 form my mic too. All the other volume options, it's 100 too. It has no effect. Hel

  The volume of the recorded sound is very low when played. I tried to solve the problems through Control Panel of configuration-sound options and increased the volume to 100 form my mic too. All the other volume options, it's 100 too. It has no effect. Help needed ASAP

  Hello

  Control Panel - SOUNDS - Audio peripheral devices configuration-manager

  Make sure you write down the description and model double click top - tab drivers - write version. Now
  Click on update drivers who cannot do anything like MS is far behind the certification of drivers. Then RIGHT
  CLICK above and UNINSTALL - REBOOT - this will rebuild the driver stack.

  If your driver shows 06 you have the default windows and part of the question.

  Go to the system manufacturer's website and get the latest Audio/Sound drivers - download - SAVE - go to the place where you
  Put them - right click on Reboot - RUN AS ADMIN -.

  Check the Version on the tab of the driver in the device as a sound Manager often restoring drivers, then install
  the current version. Restart and check after each try, not uncommon to have to run the pilot of 1 to 4 times or more.
  Just make sure that the version you have installed appears in the tab of the driver.

  Then navigate to the site of the manufacturer of the device and search for the drivers more recent and repeat the installation procedure.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  ---------------------------------------------------------

  After the updated driver.

  Click with the right button on the speaker near clock - recorders - right click in the box - check show disconnected devices
  and show disabled devices - check your micro - highlight them, then lower right properties. Do
  of course the appropriate injector is enabled and check that other settings - on the levels tab make sure MUTE is not checked
  and APPLY / OK changes.

  Also in the search for some Audio Manager Panel (perhaps named after the manufacturer of the sound driver). Mine
  is the RealTek Audio Manager, yours can be quite different name if you have one.

  How to activate Audio devices hidden in Vista
  http://www.Vistax64.com/tutorials/143447-audio-device-enable-hidden-devices.html

  Connect one microphone, music player or other audio device to your computer
  http://windowshelp.Microsoft.com/Windows/en-us/help/b0e3d7fb-1b4a-4926-8254-65da289209261033.mspx

  Problems with sound and audio or no sound - a Mr Fixit
  http://support.Microsoft.com/GP/NO_SOUND

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• My laptop is one of the 4 home cannot connect to the internet, it's Vista and it has connected w/Ethernet no problem, I called Xfinity tech, that says, is the problem of configuration! Can you help me?

  Acer laptop, Vista is, she can connect wirelessly with my friend modem but my house, she can't, I use the service of Comcast, they checked the modem is fine, they think that the problem of configuration! I'm not computer too, thank you!

  Ryan (Shih Chi)

  Hello

  How do you try to connect the computer to the House? Wired
  or wireless?
  Try the methods provided and see if it helps to solve the problem.
  Method 1:
  Check out the link and follow the troubleshooting steps in the article.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 2:
  If you try to connect to t Wireless net work then refer to this link and follow the steps.
  Connect to a network with Windows Vista wireless
  http://TechNet.Microsoft.com/en-us/library/bb878035.aspx
   
  Method 3:
  Reset TCP/IP on your computer and check. Check out the link and follow the steps.
  How to reset the Protocol Internet (TCP/IP)
  http://support.Microsoft.com/kb/299357
   
  Method 4:
  You can also visit this link and follow the steps.
  
  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us
   
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/ ) how to back up and restore the registry in Windows

• launch of checkers problems: error: trying to re-launch your game. If the problem persists, it may be network with the server problems or a problem with the configuration of your firewall.

  Windows Vista can not launch problem of checkers: try to re-launch your game. If the problem persists, it may be network with the server problems or a problem with the configuration of your firewall. Please check your firewall settings by visiting the Open Ports FAQ.

  Original title: launch of the problems of checkers:

  Hello

  If you have not yet tried to disable the antivirus/firewall software, then try the following steps to disable them.

  Disable the anti-virus software: http://windows.microsoft.com/en-US/windows-vista/Disable-antivirus-software

  Enable or disable Windows Firewall: http://windows.microsoft.com/en-US/windows-vista/Turn-Windows-Firewall-on-or-off

  IMPORTANT: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks

• The network connectivity status appears as only 'Local' error message ' there may be a problem with your domain name server (DNS) configuration "when trying to diagnose the problem.

  Original title: connection internet wireless Sony Vaio problems

  I get connection "local only" and then when I try to diagnose and repair he said: "it may be a problem with your domain name server (DNS) configuration. He said that this problem cannot be fixed automatically and I have no idea what to do.

  How do you connect to the Internet (method/ISP)? What is a stand-alone computer or a corporate work station? What is the status of virus/malware of the machine? Please give us more details so that we can help you.

  Help us help you:

  http://www.elephantboycomputers.com/page2.html#Tech_Support - See the article "how to write a Post.
  http://support.microsoft.com/default.aspx/kb/555375 - how to ask a Question

  Troubleshooting Internet connectivity

  1 answer to the first and second troubleshooting Questions:

  First Question of troubleshooting: If the problem is new, what has changed between the time things worked and the time they do not have?

  The second issue of Windows troubleshooting: what is the status of virus/malware of the machine? If you think it's clean, what programs (and versions) allows you to determine this?

  Make sure that the computer is clean - http://www.elephantboycomputers.com/page2.html#Removing_Malware

  Many variants of malware will allow a proxy server if you are unable to Internet. Go to control panel > Internet Options > connectivity tab > LAN button. If all is selected in the section Server Proxy, uncheck the box, apply/OK outside.

  2. If nothing has changed and that the computer is clean, what antivirus/security programs are you running? Have AVG 8 or Zone Alarm? These two programs have had updates that caused Internet connectivity problems. I don't recommend either of these programs, but if you want to keep check them on the mftrs.' support websites.

  3. If #2 is not applicable:

  a. unplug the router.
  b. disconnect the modem. (If you have a DOCSIS 3 modem with battery backup, press the Reset button to reset the modem so the lights go out).
  c. wait 60 seconds.
  d. plug the modem (or wait until the reboot is completed) and expect that all the lights are on.
  e. plug the router and wait until all lights are on.

  You now have an Internet connection? Otherwise:

  4. connect your computer directly to the cable/DSL modem. You now have an Internet connection? If so, there is a problem with the router. They do not last forever. Replace it.

  If there is no Internet when your computer is connected directly to the cable/DSL modem, call your ISP because something is wrong with the cable/DSL modem or your Internet service.

  MS - MVP - Elephant Boy computers - don't panic!

• During the installation of the ultimate upgrade, get "one or several components of the system could not be configured", then it restarts and pours me to premium.___How can I say what is the cause of the problem and fix it?

  I have the same problem as Laweaver.
  I have a HP pavillion Model # m9040n running the 32-bit version with service pack 1.
  My Vista Ultimate Upgrade drive is 32 bit and also has Service Pack 1 on it.
  I ran my system through the Microsoft Update and it is common.
  I ran Vista Advisor and he tells me that everything is good to go.
  I also ran my system through the center of update of HP and he is current.
  I tried the Ultimate Upgrade three times and got the same message twice.
  Of course, it waits until it reaches "end of the upgrade" before it fails.
  I turned all the extra wide including the firewall when I tried the upgrades
  My computer came with the home edition Premium already installed on it and I have the disks of backup for him if I have to do a repair on it.
  I have the same question though - how to tell what the cause of the problem and fix?
  Thank you
  Rich

  Hi Eaglesoar1,

  This problem occurs because some features of Windows Vista cannot be migrated to the upgraded version of Windows Vista.

  To resolve this issue, follow these steps:

  1. click on Start, type programs and features in the search box, and then click programs and features in the list programs.
  2. under tasks, click on turn Windows features on or OFF.
  If you are prompted for an administrator password, type the password. If you are prompted to confirm, click continue.
  3. Click to clear the check boxes for the following features:
  o Microsoft .NET Framework 3.0\XPS Viewer
  O remote differential compression
  O DFS replication service window
  4 upgrade Windows Vista to a more advanced version and then click to select the check boxes that you clicked to clear in step 3.

  For more information see the Microsoft kb article below.
  Error message when you try to upgrade Windows Vista to a more advanced version of Windows Vista: "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation.
  http://support.Microsoft.com/kb/946078

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "No access to the network" problem in Windows 7 and error message "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."

  Hello, I have a desktop PC and a laptop (DELL Inspiron N-4050).
  I have problem with my internet connection cable which is working fine on my PC, but does not not on my laptop giving an error "no access to the network.

  When I troubleshoot it says "your computer seems to be correctly configured but the device or resource (DNS SERVER) is not responding."
  I said to many technicians of microsoft online response, but they could not solve my problem and said this is my DNS problem and advised me to contact my Internet service provider. Guess it's because of my internet so why it works on my PC not on laptop?

  Yesterday, my ethernet cable pulled out my cell phone and I couldn't connect to the internet more. But on my desktop PC, it works perfectly fine. (I do not use wifi, if this information is also required) I have studied several threads with similar situations, and I have tried different methods to solve the problem to no avail. I did a system restore, but I'm having no luck. Also, I did not of the latest changes with my anti virus software and my LAN card drivers look to date.

  When I remove my cable from the laptop and again connect my cable then it works but only after the PC sat for awhile.
  1.I did flush DNS by typing "ipconfig/flushdns" in the command prompt.
  2. my IP address, DNS, subnet mask etc are set to automatic.
  3.I also added physical address taken from command line giving "ipconfig/all". for the properties of the network driver settings.
  4.I ' installed the drivers to date of 2014 on my laptop.
  5.I did a lot of searching the web, but they do not solve my problem.

  Please help me to solve it.
  I appreciate your help.
  Thank you.

  Hello Hall,

  Please keep us updated on the status of the issue.

  I suggest you to follow the steps in this Microsoft article troubleshooting and check if it helps:

  Error message "your computer seems to be configured correctly, but the device or resource (DNS server) is not responding" in Windows 7

  http://support.Microsoft.com/kb/2779064/en-us

  Hope the helps of information.

  Please reply with the results, in order to help you solve the problem.

  Thank you

• problem with the configuration of the Windows on Windows 8 updates

  hated, I an asus X553M I think its name everything was fine but but now ever time I'll start up it goes to black screen (lack of configuration of windows, undo changes updates off your computer), then it will reboot, but it just back upward with the failure to set up the screen and it continues to is time and time again iv tried everything I have photos on the laptop that are too important to lose is there a way I could get him...

  Original title: help

  Hello

  Thanks for posting your query in Microsoft Community.

  I suggest you to start from the installation media and then Auto repair and check if it helps.

  Method 1: create installation media.

  Check out the following link to create an installation media for Windows 8.

  http://Windows.Microsoft.com/en-GB/Windows-8/upgrade-product-key-only

  Method 2:

  Step 1: auto repair

  See the next procedure to start on the installation media and auto repair

  1. Insert media such as (DVD or USB key) and press the F12 key and click change default or any other option located at the bottom of the screen.

  2. In the next screen, click on the Troubleshooting option, you WinRE (Windows Recovery Environment) different options to solve the problems with the computer when it is in no State to start is displayed.

  3. Now click on repair automatic, this will open a wizard that automatically diagnose and repair problems with starting the computer.

  Step 2: System Restore

  See the next procedure to start on the installation media and perform the system restore.

  1. Insert media such as (DVD or USB key) and press the F12 key and click change default or any other option located at the bottom of the screen.

  2. In the next screen, click on troubleshooting option, allows you to display different options of WinRE (Windows Recovery Environment) to solve the problems with the computer when it is in no State to start.

  3. Now, click on the system restore, this will open a wizard that automatically diagnose and repair problems with starting the computer.

  Hope this helps, please let us know if you have further questions about Windows.

  Thank you.